MP4034 [MPS]
Offline LED Driver;
| 型号： | MP4034 |
| 厂家： | 
MONOLITHIC POWER SYSTEMS |
| 描述： | Offline LED Driver |
| 文件： | 总19页 (文件大小：873K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MP4034
Offline LED Driver
The Future of Analog IC Technology
DESCRIPTION
FEATURES
The MP4034 is an offline regulator that
provides accurate constant-current regulation.
The LED driver circuit design is simplified by
removing the opto-coupler and the secondary
feedback components.
•
Primary-Side–Control without Opto-coupler
or Secondary Feedback Circuit
Precise Constant Current Regulation
Integrated 700V MOSFET with Minimal
External Components
•
•
•
•
•
•
•
•
•
Variable Off-Time and Peak-Current Control
550µA High-Voltage Current Source
Up to 7W Output Power
Over-Voltage Protection
Over-Temperature Protection
Open-Loop Protection
The MP4034 has an integrated 700V MOSFET.
Its variable off-time control allows a flyback
converter to operate in discontinuous
conduction mode (DCM). The MP4034 also
features complete protection functions such as
VCC under-voltage lockout, over-voltage
protection, over-temperature protection, and
open-loop protection.
Natural Spectrum Shaping for Improved
EMI Signature
•
•
Low Cost and Simple External circuit
SOIC8-7A Package
The MP4034's variable switching frequency
provides natural spectrum shaping to smooth
the EMI signature, which can reduce the EMI
filter’s size and cost.
APPLICATIONS
•
Offline LED Driver
All MPS parts are lead-free and adhere to the RoHS directive. For MPS green
status, please visit MPS website under Products, Quality Assurance page.
“MPS” and “The Future of Analog IC Technology”, are Registered Trademarks
of Monolithic Power Systems, Inc.
TYPICAL APPLICATION
L
N
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
1
MP4034 – OFFLINE LED DRIVER
ORDERING INFORMATION
Part Number*
Package
Top Marking
MP4034GS
SOIC8-7A
MP4034
* For Tape & Reel, add suffix –Z (e.g. MP4034GS–Z);
PACKAGE REFERENCE
TOP VIEW
1
2
3
4
8
6
5
SOIC8-7A
ABSOLUTE MAXIMUM RATINGS (1)
Drain to GND ................................-0.7V to 700V
VCC to GND ...................................-0.3V to 30V
FB Input ..........................................-0.7V to 10V
Thermal Resistance (4)
SOIC8-7A ..............................76...... 45... °C/W
θJA
θJC
Notes:
1) Exceeding these ratings may damage the device.
2) The maximum allowable power dissipation is a function of the
maximum junction temperature TJ (MAX), the junction-to-
ambient thermal resistance θJA, and the ambient temperature
TA. The maximum allowable continuous power dissipation at
any ambient temperature is calculated by PD (MAX) = (TJ
(MAX)-TA)/θJA. Exceeding the maximum allowable power
dissipation will cause excessive die temperature, and the
regulator will go into thermal shutdown. Internal thermal
shutdown circuitry protects the device from permanent
damage.
(2)
Continuous Power Dissipation (TA = +25°C)
SOIC8-7A…………………………………...1.3W
Junction Temperature...............................150°C
Lead Temperature ....................................260°C
Storage Temperature............... -60°C to +150°C
ESD Capability Human Body Mode.......... 2.0kV
ESD Capability Machine Mode .................. 200V
3) The device is not guaranteed to function outside of its
operating conditions.
4) Measured on JESD51-7, 4-layer PCB.
Recommended Operating Conditions (3)
Operating VCC range ......................6.6V to 28V
Operating Junction Temp. (TJ). -40°C to +125°C
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
2
MP4034 – OFFLINE LED DRIVER
ELECTRICAL CHARACTERISTICS
VCC = 15V, TA = 25°C, unless otherwise noted.
Parameter
Symbol Condition
Min
Typ
Max
Units
Supply Voltage Management (VCC Pin)
VCC ON threshold
VCCH
VCCL
16.8
6
17.3
6.3
17.8
6.6
V
V
VCC OFF threshold
VCC operating voltage
Quiescent current
6.6
28
V
IQ
At no load condition, VCC=20V
60kHz, VCC=20V
360
500
0.1
410
μA
μA
µA
Operating current
IOP
Leakage current from VCC Pin
Internal MOSFET (Drain Pin)
Break down voltage
ILeak_VCC VCC=0VÆ16V, Drain float
1
VBRDSS VCC=20V, VFB=7V
ICharge VCC=4V, VDrain=100V
700
450
V
Supply Current from Drain Pin
550
1
750
10
µA
µA
Ω
Leakage current from Drain Pin ILeak_Drain VDS=500VDC
On-state resistance
RON
ID=10mA, TJ=20 degree
VFB=-0.5V
10
13
Internal Current Sense
Current Limit
ILimit
tLEB
365
230
380
300
395
370
mA
ns
Leading-edge blanking
Feedback input (FB Pin)
FB pin input current
IFB
VFB=4V
0.2
120
-0.15
4
0.5
160
-0.08
4.07
6.5
μA
mV
V
DCM detect threshold
FB open-circuit threshold
First-level FB OVP threshold
VDCM
80
-0.22
3.93
6.2
VFBOPEN
VFBOVP1
V
Second-level FB OVP threshold VFBOVP2
6.35
V
OVP sampling delay
tOVP
3.5
µs
Thermal Shutdown
Thermal shutdown threshold
150
120
°C
°C
Thermal shutdown recovery
threshold
MP4034 Rev. 1.02
www.MonolithicPower.com
3
12/4/2013
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
MP4034 – OFFLINE LED DRIVER
TYPICAL CHARACTERISTICS
Charge Current vs.
Leakage Current vs.
Junction Temperature
Breakdown Voltage vs.
Junction Temperature
Junction Temperature
850
4.0
700
3.5
800
750
700
650
600
550
500
650
3.0
600
550
500
450
400
2.5
2.0
1.5
1.0
0.5
0.0
-50 -25
0
25 50 75 100 125
-50 -25
0
25 50 75 100 125
-50 -25
0
25 50 75 100 125
V
ON Threshold vs.
V
OFF Threshold vs.
First-Level OVP Threshold
vs. Junction Temperature
CC
Junction Temperature
CC
Junction Temperature
18.0
17.5
17.0
16.5
16.0
15.5
15.0
7.00
6.75
6.50
6.25
6.00
5.75
5.50
5.25
5.00
4.100
4.075
4.050
4.025
4.000
3.975
3.950
3.925
3.900
-50 -25
0
25 50 75 100 125
-50 -25
0
25 50 75 100 125
-50 -25
0
25 50 75 100 125
DCM Detect Threshold
vs. Temperature Chart
FB Open Circuit Threshold
vs. Junction Temperature
Second-Level OVP Threshold
vs. Junction Temperature
0.000
-0.020
-0.040
-0.060
-0.080
-0.100
-0.120
-0.140
-0.160
-0.180
-0.200
7.000
0.130
0.125
0.120
0.115
0.110
0.105
0.100
6.750
6.500
6.250
6.000
5.750
5.500
5.250
5.000
-50 -25
0
25 50 75 100 125
-50 -25
0
25 50 75 100 125
-50 -25
0
25 50 75 100 125
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
4
MP4034 – OFFLINE LED DRIVER
TYPICAL CHARACTERISTICS (continued)
OVP Sample Delay vs.
Junction Temperature
On State Resistance vs.
Junction Temperature
Current I
vs.
Junction Temperature
Limit
400
390
380
370
20
15
10
5.0
4.5
4.0
3.5
3.0
2.5
2.0
5
0
360
350
-50 -25
0
25 50 75 100 125
-50 -25
0
25 50 75 100 125
-50 -25
0
25 50 75 100 125
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
5
MP4034 – OFFLINE LED DRIVER
TYPICAL PERFORMANCE CHARACTERISTICS
Performance waveforms are tested on the evaluation board of the Design Example section.
VIN = 230VAC, VOUT = 40V, IOUT=0.13A, L = 1.2mH, TA = 25°C, unless otherwise noted.
Input Power Startup
OCkP Recovery
SCP Entry
Input Power Shut Down
OCkP Entry
V
V
V
DS
DS
DS
100V/div.
100V/div.
100V/div.
V
CC
10V/div.
I
OUT
I
I
OUT
OUT
100mA/div.
50mA/div.
50mA/div.
OVP Entry
OVP Recovery
V
V
DS
DS
V
DS
100V/div.
100V/div.
100V/div.
V
V
V
CC
CC
CC
10V/div.
10V/div.
10V/div.
I
I
I
OUT
OUT
OUT
100mA/div.
50mA/div.
50mA/div.
SCP Recovery
Output Current Ripple
V
V
DS
DS
100V/div.
100V/div.
I
OUT
V
V
CC
CC
50mA/div.
10V/div.
10V/div.
I
I
OUT
OUT
50mA/div.
50mA/div.
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
6
MP4034 – OFFLINE LED DRIVER
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Performance waveforms are tested on the evaluation board of the Design Example section.
VIN = 230VAC, VOUT = 40V, IOUT=0.13A, L = 1.2mH, TA = 25°C, unless otherwise noted.
Normal Operation
Output Current Regulation
5
4
3
2
1
0
V
DS
-1
-2
-3
-4
-5
100V/div.
V
CC
10V/div.
V
FB
10V/div.
I
OUT
100mA/div.
80 100120140160180200220240260
INPUT VOLTAGE (V)
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
7
MP4034 – OFFLINE LED DRIVER
PIN FUNCTIONS
SOIC8-7A
Name Description
Pin #
Supply. An internal high-voltage current source charges VCC voltage to VCCH to start the IC.
VCC The internal high-voltage current source will also turn on when VCC falls below VCCL to
charge VCC. Connect a 0.1µF ceramic decoupling capacitor as close as possible to this pin.
1
Feedback. Controls the OVP function. If VFB=4.0V, the first-level OVP triggers and output
FB voltage remains constant. If VFB=6.35V, the second-level OVP triggers, switch immediately
shuts off, and IC restarts.
3
2, 4, 5, 6 GND Ground.
8
Drain Internal MOSFET Drain. Input for the startup high-voltage current source.
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
8
MP4034 – OFFLINE LED DRIVER
FUNCTIONAL BLOCK DIAGRAM
Figure 1: Functional Block Diagram
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
9
MP4034 – OFFLINE LED DRIVER
OPERATION
Transformer Design
Figure 4: Isolated Flyback LED Driver
Figure 2: Simplified Flyback Converter
The MP4034 ensures that the circuit operates
in discontinues conduction mode (DCM). When
the IC internal MOSFET turns on, the current (iP)
flowing through transformer’s primary-side
winding (NP) increases linearly until it reaches
its peak current limit (IPK)
Startup
Initially, the IC is self-supplying through the
internal high-voltage current source, which is
drawn from the Drain pin. The internal high-
voltage current source will turn off for better
efficiency when VCC reaches the VCC ON
threshold. Then the transformer’s auxiliary
winding takes over as the power source. When
VCC falls below the VCC OFF threshold, the IC
stops switching and the internal high-voltage
current source turns on again. See Figure 3 for
the start-up waveform.
0
Vcc
Regulation Occurs Here
Auxiliary Winding Takes Charge
Figure 5: Current Waveform
V
17.3
Assume switching frequency is fs, the power
stored in the inductor is given by:
6.3V
1
P = LM ×IP2K × fS
Drain
2
Switching Pulses
Then inductance of coupling inductor is then:
2×PO
LM =
IP2K × fS × η
High voltage
current source
Where PO is output power and η is the
estimated efficiency.
ON
When MP4034’s internal switch turns off, the
freewheeling current (iS) will flow through
secondary-side diode and decrease linearly, as
shown in Figure 5.
OFF
Figure 3: VCC UVLO
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
10
MP4034 – OFFLINE LED DRIVER
The relationship of peak current at ON period
and OFF period is:
This provides enough information to design the
transformer turn ratio.
Leading-Edge Blanking
NP
IPK _S
=
×IPK
Turning the power switch on induces a spike on
the sense resistor. To avoid falsely terminating
the switching pulse, the MP4034 includes a
300ns leading-edge blanking period. During this
blanking period, the current sense comparator
is disabled and the gate driver can not switch
off.
NS
Where NP is the number of primary winding
turns, and NS is the number of secondary
winding turns.
The MP4034 detects the secondary side diode
duty cycle by sampling the auxiliary winding
voltage and generates a ZCD signal as shown
in Figure 6.
DCM Detection
The MP4034 is designed to operate in
discontinuous conduction mode (DCM). To
avoid operating in continuous conduction mode
(CCM), the MP4034 detects the falling edge of
the FB input voltage with each cycle. If the chip
does not detect a 120mV falling edge, it will
stop switching.
Over Voltage Protection
The MP4034 has two levels of over-voltage
protection based on the FB voltage.
Figure 6: VFB and ZCD Waveforms
In normal operation, MP4034 samples the FB
pin voltage 3.5μs after the primary switch turns
off, as shown in Figure 6.
When the FB voltage is high—which means
that the current is flowing through secondary-
side diode—the ZCD signal goes high.
Conversely, when the FB voltage is low—which
means no current flows through the secondary-
side diode—the ZCD signal goes low, meaning
the secondary-side diode duty cycle (DS) is:
TS _ ON
DS =
TS _ ON + TS _ OFF
Figure 7: Auxiliary Voltage Waveform
Then the average output current is:
1
The relationship of output voltage and VFB is :
IOUT
=
×IPK _ S ×DS
2
NP _ AU
NS
RDOWN
VFB
=
×
×(VO + VD )
TS _ ON
1 NP
×
RUP + RDOWN
=
×IPK ×
2 NS
TS _ ON + TS _ OFF
Where VD is the secondary-diode forward-drop
voltage.
The MP4034 keeps
current is:
at 0.4. Thus the output
DS
When the MP4034 detects that the FB voltage
equals 4.0V, the first level OVP triggers. The
switching frequency drops to maintain the
output voltage at a constant value. If VFB
voltage exceeds 6.35V for 3.5μs, it will shut
down immediately and discharge the VCC
1 NP
1 NP
IOUT
=
×
×IPK ×DS =
×
×IPK
2 NS
5 NS
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
11
MP4034 – OFFLINE LED DRIVER
voltage. When VCC drops to UVLO, the MP4034
will restart.
1
2
N-1
N
Figure 8: LED String
Assume the forward voltage of one LED is VF
and the total number of LEDs on the string is N.
So the output voltage can be calculated as
N×VF. To ensure that OVP won’t trigger during
normal operation; the VFB should not exceed
VFBOVP1 (typical 4.0V). However, avoid a large
output voltage when OVP occurs. So the
voltage reflected on the FB pin should be:
NP _ AU
NS
RDOWN
VFB
=
×
×(N× VF + VD ) = 0.85VFBOVP1
RDOWN + RUP
Open-Circuit Protection (OCkP)
The MP4034 has open-circuit protection
(OCkP). If the −0.15V falling edge of VFB can
not be monitored—which means the feedback
loop is open—the MP4034 immediately shuts
off the driving signals and enters hiccup mode.
The MP4034 resumes normal operation when
the fault has been removed.
Thermal Shutdown (TSD)
When the temperature of the IC exceeds 150°C,
the over-temperature protection is enacted and
the IC enters auto-recovery mode. When the
temperature falls below 120°C, the IC resumes
working.
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
12
MP4034 – OFFLINE LED DRIVER
APPLICATION INFORMATION
If the VDC(min) can not satisfy this express,
increase the value of the input capacitors to
COMPONENT SELECTION
Input Filter
Input filter produces a DC source through the
rectifier from the AC input power Figure 9 shows
the input filter and Figure 10 shows the typical
DC bus voltage waveform.
increase the VDC(min)
.
Output Diode
Use a Schottky diode because of its fast
switching speed and low forward voltage drop for
better efficiency.
If a lower average efficiency (3%-4%) is
acceptable, replace the output diode with a PN-
junction diode or other non-Schottky diode to
lower costs.
Leakage Inductance
The transformer leakage inductance will
decrease the system efficiency and affect the
output
current
constant
precision.
The
Figure 9: Input Filter
transformer structure should be optimized to
improve the primary side and secondary side
coupling and minimize the transformer leakage
inductance of transformer. Aim for a leakage
inductance that is less than 5% inductance.
RCD Snubber
The transformer leakage inductance causes the
MOSFET drain voltage spike and the excessive
ringing on the drain voltage waveform.
The RCD snubber circuit can limit this Drain
voltage spike. Figure 11 shows the RCD snubber
circuit.
Figure 10: DC Input-Voltage Waveform
Bulk capacitors C1 and C2 filter the rectified AC.
Inductor L forms a π filter with C1 and C2 to
restrain the differential-mode EMI noise. The
resistor (R) in parallel with the inductor (L)
restrains the mid-frequency-band EMI noise.
Normally, R is selected between 1kΩ and 10kΩ.
The DC input capacitors, C1 and C2, are usually
2µF/W to 3µF/W for the universal input condition.
For a 230VAC single-range application, the
capacitor can be half that value. Normally, the
minimum DC voltage should not be too low to
ensure the converter can supply the maximum
power to the load which can be express as
follows:
Figure 11: RCD Snubber
NP
NS
DS
VDC(min)
≥
⋅(N⋅ VF + VD )⋅
1−DS
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
13
MP4034 – OFFLINE LED DRIVER
Select RSN and CSN for an acceptable voltage
spike and better system operation.
The power dissipated in the snubber circuit is
approximately:
VSN
1
2
PSN = ⋅LK ⋅IPK
⋅
× fS
2
VSN −NPS × VO
Where:
•
•
•
LK is the leakage inductance,
SN is the clamp voltage,
V
Figure 12: FB Pin in Series with ON Resistor
NPS is the turn ratio of primary and secondary
side.
Dummy Load
A dummy load is required in open-output
applications for good over-voltage protection.
Use a dummy load of ~10mW for good load
regulation.
The power consumed in the snubber resistor
(RSN), the resistor (RSN) is:
2
VSN
RSN
=
Maximum Switching Frequency
Because of the parameter tolerance of the
sampling detecting time and inductance
PSN
The maximum ripple of the snubber capacitor
voltage is:
tolerances, select
a
secondary-side-diode
conduction time that exceeds 5.4µs as follows.
VSN
ΔVSN =
NS ⋅LM
NP ⋅(VO + VD )
CSN ⋅RSN ⋅ fS
TS _ ON = IPK ⋅
> 5.4μs
Generally, a 15% ripple is reasonable. Use the
previous equation to approximate CSN.
For high or low temperature operation, select a
maximum switching frequency below 75kHz.
The damping resistor (R) in series with the RCD
has a relatively large value to prevent any
excessive ringing voltage that can affect the EMI.
Use a damping resistor of about 200Ω to 500Ω to
limit the drain voltage ringing.
Resistor Divider
For better application performance, use a resistor
divider with values in the range of 10kΩ to 100kΩ
to limit noise from adjacent components on the
FB pin. Connect a resistor with a value ranging
from 1kΩ to 2kΩ from the FB pin to the resistor
divider to limit substrate injection current effects,
as shown in Figure 12.
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
14
MP4034 – OFFLINE LED DRIVER
PCB Layout Guide
PCB layout is very important to achieve reliable
operation, and good EMI and thermal
performance. The use design guide as follows
to help optimize performance.
1. Minimize the loop area formed by the input
capacitor, the MP4034 drain-source, and the
primary winding to reduce EMI noise.
2. The copper area connected to source pins
acts as a heat sink. Provide a large copper area
to improve the thermal performance.
3. Minimize the clamp circuit loop to reduce EMI.
Bottom Layer
4. Minimize the secondary loop area of the
output diode and output filter to reduce the EMI
noise. In addition, provide a sufficient copper
area at the anode and cathode terminal of the
output diode for heat dissipation.
Figure 13: PCB Layout
Design Example
Below are design examples following the
application
guidelines
for
the
given
specifications:
5. Place the AC input away from the switching
nodes to minimize the noise coupling that may
bypass the input filter.
Table 1: Design Example
Example 1
VIN
VOUT
IOUT
85VAC-265VAC
6. Place the bypass capacitor as close as
possible to the IC and source.
40V
0.13A
7. Place the feedback resistors at the FB pin
and minimize the feedback sampling loop area
to minimize noise coupling.
Example 2
VIN
VOUT
IOUT
85VAC-265VAC
10V
8. Use a single point connection at the negative
terminal of the input filter capacitor for the
MP4034 source pin and bias winding return.
0.35A
Figure 14 and Figure 15 show the detailed
isolated application, while Figure 16 and Figure
17 show the detailed non-isolated application.
These examples were used in the Typical
Performance Characteristics section. For more
applications, please refer to the related
evaluation board datasheets.
Figure 13 shows a layout example.
Top Layer
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
15
MP4034 – OFFLINE LED DRIVER
TYPICAL APPLICATION CIRCUITS
Figure 14: Typical Application Example
Universal Input, Driving 14 LEDs in Series, 130mA LED Current, 6W Isolation Flyback Converter
L1 1mH/0.1A
T1
1
R1 10k/0805
R2
499k
1206
C3
D3
NP
ES1D/200V/1A
2.2nF/630V
1206
6
LED+
10V/0.35A
LED-
FR110/1W
2
3
L
R7
10k
C5
22uF/16V
1206
BD1
MB6S
600V/0.5A
C2
2.2uF/400V
C1
D1
NS
4.7uF/400V
85VAC~265VAC
N
5
R3
PGND
NP_AU
510
0805
EE13
AGND
Lp=1.1mH
NP:NP_AU:NS=95:23:19
4
PGND
D2
BAV21W
200V/0.2A
CY1
1nF/4kV
U1
R4
R6
20/0805
5
6
4
3
2
1
GND
GND
FB
32.4k/1%
PGND
AGND
GND
R5
GND
VCC
13.3k/1%
PGND
8
Drain
C4
MP4034/SOIC8-7A
4.7uF/50V
1206
PGND
Figure 15: Typical Application Example
Universal Input, Driving 3 LEDs in Series, 350mA LED Current, 3.5W Isolation Flyback Converter
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
16
MP4034 – OFFLINE LED DRIVER
Figure 16: Typical Application Example
Universal Input, Driving 14 LEDs in Series, 150mA LED Current, 6W Non-isolated Buck-Boost Converter
Figure 17: Typical Application Example
Universal Input, Driving 3 LEDs in Series, 350mA LED Current, 3.5W Non-isolated Buck-Boost Converter
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
17
MP4034 – OFFLINE LED DRIVER
FLOW CHART
Start
Y
V
CCL
VCC
<
Monitor V
CC
N
N
Monitor V CC
VCC
>
VCCH
Y
N
Monitor V
FB
N
CC Operation
VFB >-0.15V
for entire
cycle
VFB>4.0V
Y
Y
OCkP
Operation
First Level OVP
CV Operation
N
VFB>6.35V
Y
Shut Off
Switching
Pulse
Discharge
Vcc to OFF
threshold
MP4034 Rev. 1.02
www.MonolithicPower.com
18
12/4/2013
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
MP4034 – OFFLINE LED DRIVER
PACKAGE INFORMATION
SOIC8-7A
0.189(4.80)
0.197(5.00)
0.050(1.27)
0.024(0.61)
8
5
0.063(1.60)
0.150(3.80)
0.157(4.00)
0.228(5.80)
0.244(6.20)
0.213(5.40)
PIN 1 ID
1
4
TOP VIEW
RECOMMENDED LAND PATTERN
0.053(1.35)
0.069(1.75)
0.0075(0.19)
0.0098(0.25)
SEATING PLANE
0.004(0.10)
0.010(0.25)
0.013(0.33)
0.020(0.51)
SEE DETAIL "A"
SIDE VIEW
0.050(1.27)
BSC
FRONT VIEW
0.010(0.25)
0.020(0.50)
x 45o
NOTE:
1) CONTROL DIMENSION IS IN INCHES. DIMENSION IN
BRACKET IS IN MILLIMETERS.
GAUGE PLANE
0.010(0.25) BSC
2) PACKAGE LENGTH DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS.
3) PACKAGE WIDTH DOES NOT INCLUDE INTERLEAD FLASH
OR PROTRUSIONS.
4) LEAD COPLANARITY(BOTTOM OF LEADS AFTER FORMING)
0.016(0.41)
0.050(1.27)
0o-8o
SHALL BE0.004" INCHES MAX.
5) JEDEC REFERENCE ISMS-012.
6) DRAWING IS NOT TO SCALE.
DETAIL "A"
NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third
party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal
responsibility for any said applications.
MP4034 Rev. 1.02
12/4/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
19
相关型号：
MP404W-BP
Bridge Rectifier Diode, 1 Phase, 40A, 400V V(RRM), Silicon, ROHS COMPLIANT, PLASTIC, MP-50W, 4 PIN
MCC
©2020 ICPDF网 联系我们和版权申明