MPQ4458DQT [MPS]
Industrial Grade ,1A, 4MHz, 36V Step-Down Converter;型号: | MPQ4458DQT |
厂家: | MONOLITHIC POWER SYSTEMS |
描述: | Industrial Grade ,1A, 4MHz, 36V Step-Down Converter 开关 光电二极管 |
文件: | 总16页 (文件大小:362K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MPQ4458
Industrial Grade ,1A, 4MHz, 36V
Step-Down Converter
The Future of Analog IC Technology
FEATURES
DESCRIPTION
•
•
•
•
•
Guaranteed Industrial Temp Range
120μA Quiescent Current
Wide 3.8V to 36V Operating Input Range
300mΩ Internal Power MOSFET
Up to 4MHz Programmable Switching
Frequency
The MPQ4458 is a high frequency step-down
switching regulator with an integrated internal
high-side high voltage power MOSFET. It
provides 1 A output with current mode control
for fast loop response and easy compensation.
The wide 3.8V to 36V input range
•
•
•
Ceramic Capacitor Stable
Internal Soft-Start
Precision Current Limit without a Current
Sensing Resistor
accommodates
a
variety of step-down
applications, including those in automotive
systems. A 120µA operational quiescent current
is suitable for use in battery-powered
applications.
•
•
•
Up to 95% Efficiency
Output Adjustable from 0.8V to 30V
Available in 10-Pin 3x3 TQFN Package
The frequency foldback helps prevent inductor
current runaway during startup and thermal
shutdown provides reliable, fault tolerant
operation.
APPLICATIONS
•
•
•
•
•
High Voltage Power Conversion
Automotive Systems
Industrial Power Systems
Distributed Power Systems
Battery Powered Systems
By switching at 4MHz, the MPQ4458 prevents
EMI (Electromagnetic Interference) noise
problems, such as those found in AM radio and
ADSL applications.
All MPS parts are lead-free and adhere to the RoHS directive. For MPS green
status, please visit MPS website under Quality Assurance. “MPS” and “The
Future of Analog IC Technology” are Registered Trademarks of Monolithic
Power Systems, Inc.
The MPQ4458 is available in thin 10-pin 3mm x 3mm
TQFN package.
TYPICAL APPLICATION
Efficiency vs
Load Current
100
V =5V
I
C3
150pF
90
80
70
60
50
40
30
20
4
3
7
5
8, 9
10
COMP
EN
VIN
BST
SW
V
IN
36V Max
V =24V
I
C6
NS
V =12V
I
CONTROL
L1
C4
MPQ4458
FREQ
2.2∝H
100nF
1, 2
6
V
OUT
C2
5V @ 1A
10MQ100N
22∝F
FB
GND
V =3.3V
O
0
500
1000
LOAD CURRENT (mA)
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
1
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
ORDERING INFORMATION
Part Number*
Package
Top Marking
TQFN10 (3mm x3mm)
MPQ4458DQT
T2
* For Tape & Reel, add suffix –Z (e.g. MPQ4458DQT–Z).
For RoHS Compliant packaging, add suffix –LF (e.g. MPQ4458DQT–LF–Z)
PACKAGE REFERENCE
TOP VIEW
SW
SW
1
2
3
4
5
10 BST
9
8
7
6
VIN
EN
VIN
COMP
FB
FREQ
GND
EXPOSED PAD
ON BACKSIDE
ABSOLUTE MAXIMUM RATINGS (1)
Supply Voltage (VIN).....................–0.3V to +40V
Switch Voltage (VSW)............ –0.3V to VIN + 0.3V
BST to SW.....................................–0.3V to +6V
All Other Pins.................................–0.3V to +6V
Thermal Resistance (4)
TQFN10 (3mm x3mm)............50...... 12... °C/W
θJA
θJC
Notes:
1) Exceeding these ratings may damage the device.
2) The maximum allowable power dissipation is a function of the
maximum junction temperature TJ (MAX), the junction-to-
ambient thermal resistance θJA, and the ambient temperature
TA. The maximum allowable continuous power dissipation at
any ambient temperature is calculated by PD (MAX) = (TJ
(MAX)-TA)/θJA. Exceeding the maximum allowable power
dissipation will cause excessive die temperature, and the
regulator will go into thermal shutdown. Internal thermal
shutdown circuitry protects the device from permanent
damage.
(2)
Continuous Power Dissipation (TA = +25°C)
............................................................. 2.5W
Junction Temperature...............................150°C
Lead Temperature ....................................260°C
Storage Temperature.............. –65°C to +150°C
Recommended Operating Conditions (3)
Supply Voltage VIN ...........................3.8V to 36V
Output Voltage VOUT.........................0.8V to 30V
Operating Junct. Temp (TJ)..... –40°C to +125°C
3) The device is not guaranteed to function outside of its
operating conditions.
4) Measured on JESD51-7 4-layer board.
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
2
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
ELECTRICAL CHARACTERISTICS
VIN = 12V, VEN = 2.5V, VCOMP = 1.4V, TJ = -40°C to +85°C, unless otherwise noted. Typical values
are at TJ = 25°C.
Parameter
Symbol Condition
Min
Typ
Max Units
0.776
0.770
0.8
0.824
0.830
1.0
V
TJ = 25°C
Feedback Voltage
VFB
4.5V < VIN < 36V
Feedback Bias Current
Upper Switch On Resistance
Upper Switch Leakage
Current Limit
IFB
VFB= 0.8V
0.01
300
1
μA
mΩ
μA
A
RDS(ON) VBST – VSW = 5V
VEN = 0V, VSW = 0V, VIN = 36V
Duty Cycle = 50%
1.2
1.8
COMP
Transconductance
Error Amp Voltage Gain (5)
to
Current
Sense
GCS
3.1
A/V
200
60
V/V
µA/V
µA
µA
V
Error Amp Transconductance
Error Amp Min Source current
Error Amp Min Sink current
VIN UVLO Threshold
ICOMP = ±3µA
VFB = 0.7V
VFB = 0.9V
20
100
5
–5
2.55
3.0
0.35
1.5
2
3.45
VIN UVLO Hysteresis
Soft-Start Time (5)
V
0V < VFB < 0.8V
RFREQ = 45kꢀ
RFREQ = 18kꢀ
VEN = 0V
ms
MHz
MHz
µA
µA
°C
1.55
3.10
2.45
4.90
18
Oscillator Frequency
fS
4
Shutdown Supply Current
Quiescent Supply Current
Thermal Shutdown
12
IQ
No load, VFB = 0.9V
120
150
15
165
Thermal Shutdown Hysteresis
Minimum Off Time
Minimum On Time (5)
°C
100
100
1.5
300
ns
ns
EN Up Threshold
1.2
1.8
V
EN Threshold Hysteresis
mV
Note:
5) Guaranteed by design.
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
3
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
PIN FUNCTIONS
Pin #
Name Description
Switch Node. This is the output from the high-side switch. A low Vf Schottky rectifier to
ground is required. The rectifier must be close to the SW pins to reduce switching spikes.
Enable Input. Pulling this pin below the specified threshold shuts the chip down. Pulling it up
above the specified threshold or leaving it floating enables the chip.
Compensation. This node is the output of the GM error amplifier. Control loop frequency
compensation is applied to this pin.
1, 2
SW
EN
3
4
COMP
Feedback. This is the input to the error amplifier. An external resistive divider connected
between the output and GND is compared to the internal +0.8V reference to set the
regulation voltage.
5
FB
GND,
Ground. It should be connected as close as possible to the output capacitor avoiding the high
6
7
Exposed current switch paths. The exposed pad and GND pin must be connected to the same ground
Pad
plane.
Switching Frequency Program Input. Connect a resistor from this pin to ground to set the
switching frequency.
FREQ
Input Supply. This supplies power to all the internal control circuitry, both BS regulators and
the high-side switch. A decoupling capacitor to ground must be placed close to this pin to
minimize switching spikes.
Bootstrap. This is the positive power supply for the internal floating high-side MOSFET driver.
Connect a bypass capacitor between this pin and SW pin.
8, 9
10
VIN
BST
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
4
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
TYPICAL PERFORMANCE CURVES
VIN = 12V, VOUT = 5V, fS = 500KHz, TA = +25°C, unless otherwise noted.
4.0
3.5
V
V
OUT
OUT
AC Coupled
20mV/div.
AC Coupled
20mV/div.
3.0
2.5
2.0
1.5
1.0
V
V
SW
SW
10V/div.
10V/div.
I
L
1A/div.
0.5
0.0
I
L
1A/div.
10
100
1000
V
EN
5V/div.
V
V
EN
5V/div.
EN
V
OUT
5V/div.
2V/div.
V
V
OUT
OUT
2V/div.
2V/div.
V
V
SW
SW
V
10V/div.
10V/div.
SW
10V/div.
I
L
I
L
1A/div.
I
1A/div.
L
1A/div.
V
EN
V
OUT
5V/div.
2V/div.
V
OUT
2V/div.
V
OUT
2V/div.
V
SW
I
10V/div.
L
1A/div.
I
I
L
L
1A/div.
1A/div.
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
5
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
BLOCK DIAGRAM
V
VIN
IN
+
--
+
--
5V
2.6V
REFERENCE UVLO/
INTERNAL
REGULATORS
EN
THERMAL
SHUTDOWN
BST
SW
SW
--
+
I
SW
1.5ms SS
SS
V
OUT
I
Level
Shift
SW
FB
Gm Error Amp
--
+
COMP
SS
0V8
OSCILLATOR
CLK
V
OUT
FREQ
GND
COMP
Figure 1—Functional Block Diagram
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
6
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
OPERATION
The MPQ4458 is
a
variable frequency,
chip can be enabled and disabled by EN which
has positive logic. Its falling threshold is a
precision 1.2V, and its rising threshold is 1.5V
(300mV higher).
non-synchronous, step-down switching regulator
with an integrated high-side high voltage power
MOSFET. It provides a single highly efficient
solution with current mode control for fast loop
response and easy compensation. It features a
wide input voltage range, internal soft-start
control and precision current limiting. Its very low
operational quiescent current makes it suitable
for battery powered applications.
When floating, EN is pulled up to about 3.0V by
an internal 1µA current source so it is enabled.
To pull it down, 1µA current capability is needed.
When EN is pulled down below 1.2V, the chip is
put into the lowest shutdown current mode.
When EN is higher than zero but lower than its
rising threshold, the chip is still in shutdown
mode but the shutdown current increases slightly.
PWM Control
At moderate to high output current, the MPQ4458
operates in a fixed frequency, peak current
control mode to regulate the output voltage. A
PWM cycle is initiated by the internal clock. The
power MOSFET is turned on and remains on
until its current reaches the value set by the
COMP voltage. When the power switch is off, it
remains off for at least 100ns before the next
cycle starts. If, in one PWM period, the current in
the power MOSFET does not reach the COMP
set current value, the power MOSFET remains
on, saving a turn-off operation.
Under-Voltage Lockout (UVLO)
Under-voltage lockout (UVLO) is implemented to
protect the chip from operating at insufficient
supply voltage. The UVLO rising threshold is
about 3.0V while its falling threshold is a
consistent 2.6V.
Internal Soft-Start
The soft-start is implemented to prevent the
converter output voltage from overshooting
during startup. When the chip starts, the internal
circuitry generates a soft-start voltage (SS)
ramping up from 0V to 2.6V. When it is lower
than the internal reference (REF), SS overrides
REF so the error amplifier uses SS as the
reference. When SS is higher than REF, REF
regains control.
Error Amplifier
The error amplifier compares the FB pin voltage
with the internal reference (REF) and outputs a
current proportional to the difference between the
two. This output current is then used to charge
the external compensation network to form the
COMP voltage, which is used to control the
power MOSFET current.
Thermal Shutdown
Thermal shutdown is implemented to prevent the
chip from operating at exceedingly high
temperatures. When the silicon die temperature
is higher than its upper threshold, it shuts down
the whole chip. When the temperature is lower
than its lower threshold, the chip is enabled again.
During operation, the minimum COMP voltage is
clamped to 0.9V and its maximum is clamped to
2.0V. COMP is internally pulled down to GND in
shutdown mode. COMP should not be pulled up
beyond 2.6V.
Internal Regulator
Floating Driver and Bootstrap Charging
The floating power MOSFET driver is powered by
an external bootstrap capacitor. This floating
driver has its own UVLO protection. This UVLO’s
rising threshold is 2.2V with a threshold of
150mV.
Most of the internal circuitries are powered from
the 2.6V internal regulator. This regulator takes
the VIN input and operates in the full VIN range.
When VIN is greater than 3.0V, the output of the
regulator is in full regulation. When VIN is lower
than 3.0V, the output decreases.
The bootstrap capacitor is charged and regulated
to about 5V by the dedicated internal bootstrap
regulator. When the voltage between the BST
and SW nodes is lower than its regulation, a
Enable Control
The MPQ4458 has a dedicated enable control
pin (EN). With high enough input voltage, the
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
7
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
PMOS pass transistor connected from VIN to
current of the internal power MOSFET is
internally limited.
BST is turned on. The charging current path is
from VIN, BST and then to SW. External circuit
should provide enough voltage headroom to
facilitate the charging.
Startup and Shutdown
If both VIN and EN are higher than their
appropriate thresholds, the chip starts. The
reference block starts first, generating stable
reference voltage and currents, and then the
internal regulator is enabled. The regulator
provides stable supply for the remaining
circuitries.
As long as VIN is sufficiently higher than SW, the
bootstrap capacitor can be charged. When the
power MOSFET is ON, VIN is about equal to SW
so the bootstrap capacitor cannot be charged.
When the external diode is on, the difference
between VIN and SW is largest, thus making it
the best period to charge. When there is no
current in the inductor, SW equals the output
voltage VOUT so the difference between VIN and
VOUT can be used to charge the bootstrap
capacitor.
While the internal supply rail is up, an internal
timer holds the power MOSFET OFF for about
50µs to blank the startup glitches. When the
internal soft-start block is enabled, it first holds its
SS output low to ensure the remaining circuitries
are ready and then slowly ramps up.
At higher duty cycle operation condition, the time
period available to the bootstrap charging is less
so the bootstrap capacitor may not be sufficiently
charged.
Three events can shut down the chip: EN low,
VIN low and thermal shutdown. In the shutdown
procedure, power MOSFET is turned off first to
avoid any fault triggering. The COMP voltage and
the internal supply rail are then pulled down.
In case the internal circuit does not have
sufficient voltage and the bootstrap capacitor is
not charged, extra external circuitry can be used
to ensure the bootstrap voltage is in the normal
operational region. Refer to External Bootstrap
Diode in Application section.
Programmable Oscillator
The MPQ4458 oscillating frequency is set by an
external resistor, RFREQ from the FREQ pin to
ground. The relationship between RFREQ and fS
refer to table1 in Application section.
The DC quiescent current of the floating driver is
about 20µA. Make sure the bleeding current at
the SW node is higher than this value, such that:
VO
IO
+
> 20μA
(R1+ R2)
Current Comparator and Current Limit
The power MOSFET current is accurately sensed
via a current sense MOSFET. It is then fed to the
high speed current comparator for the current
mode control purpose. The current comparator
takes this sensed current as one of its inputs.
When the power MOSFET is turned on, the
comparator is first blanked till the end of the turn-
on transition to avoid noise issues. The
comparator then compares the power switch
current with the COMP voltage. When the
sensed current is higher than the COMP voltage,
the comparator output is low, turning off the
power MOSFET. The cycle-by-cycle maximum
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
8
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
APPLICATION INFORMATION
Setting the Frequency
A few µA of current from the high-side BS
circuitry can be seen at the output when the
MPQ4458 is at no load. In order to absorb this
small amount of current, keep R2 under 40kꢀ.
A typical value for R2 can be 40.2kꢀ. With this
value, R1 can be determined by:
The MPQ4458 has an externally adjustable
frequency. The switching frequency (fS) can be
set using a resistor at FREQ pin (RFREQ). The
recommended RFREQ value for various fS see
table1.
Table 1—fS vs. RFREQ
R1= 50.25 × (VOUT − 0.8)(kΩ)
R
FREQ (kΩ)
fS (MHz)
4
For example, for a 3.3V output voltage, R2 is
40.2kꢀ, and R1 is 127kꢀ.
18
20
3.8
3.5
3.3
3
Inductor
The inductor is required to supply constant
current to the output load while being driven by
the switched input voltage. A larger value
inductor will result in less ripple current that will
result in lower output ripple voltage. However,
the larger value inductor will have a larger
physical size, higher series resistance, and/or
lower saturation current. A good rule for
determining the inductance to use is to allow
the peak-to-peak ripple current in the inductor
to be approximately 30% of the maximum
switch current limit. Also, make sure that the
peak inductor current is below the maximum
switch current limit. The inductance value can
be calculated by:
22.1
24
26.7
30
2.8
2.5
2.2
2
33.2
39
45.3
51
1.8
1.6
1.4
1.2
1
57.6
68
80.6
100
133
200
340
536
⎛
⎜
⎝
⎞
⎟
⎟
⎠
0.8
0.5
0.3
0.2
VOUT
VOUT
⎜
L1=
× 1−
fS × ΔIL
V
IN
Where VIN is the input voltage, fS is the
switching frequency, and ΔIL is the peak-to-
peak inductor ripple current. Choose an
inductor that will not saturate under the
maximum inductor peak current. The peak
inductor current can be calculated by:
Setting the Output Voltage
The output voltage is set using a resistive
voltage divider from the output voltage to FB pin.
The voltage divider divides the output voltage
down to the feedback voltage by the ratio:
⎛
⎞
⎟
⎟
⎠
VOUT
VOUT
⎜
ILP = ILOAD
+
× 1−
⎜
⎝
2 × fS × L1
V
IN
R2
VFB = V
OUT R1+ R2
Where ILOAD is the load current. Table 2 lists a
number of suitable inductors from various
manufacturers. The choice of which style
inductor to use mainly depends on the price vs.
size requirements and any EMI requirement.
Where VFB is the feedback voltage and VOUT is
the output voltage.
Thus the output voltage is:
(R1+ R2)
VOUT = VFB
R2
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
9
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
Table 2—Selected Inductors
Inductance Max DCR Current Rating
Dimensions
Manufacturer
Part Number
(µH)
2.2µH
3.3µH
4.7µH
10µH
15µH
22µH
2.2µH
3.3µH
4.7µH
10µH
15µH
(Ω)
(A)
L x W x H (mm3)
Wurth Electronics
Wurth Electronics
Wurth Electronics
Wurth Electronics
Wurth Electronics
Wurth Electronics
TDK
7447789002
7447789003
0.019
0.024
0.033
0.035
0.025
0.031
0.012
0.02
4A
7.3x7.3x3.2
7.3x7.3x3.2
7.3x7.3x3.2
10x10x3.8
3.42A
2.9A
3.6A
3.75
3.37
5.4A
4.1A
3.4A
3A
7447789004
744066100
744771115
12x12x6
744771122
12x12x6
RLF7030T-2R2
RLF7030T-3R3
RLF7030T-4R7
SLF10145T-100
SLF12565T-150M4R2
7.3x6.8x3.2
7.3x6.8x3.2
7.3x6.8x3.2
10.1x10.1x4.5
12.5x12.5x6.5
TDK
TDK
0.031
0.0364
0.0237
TDK
TDK
4.2
TDK
SLF12565T-220M3R5
22µH
0.0316
3.5
12.5x12.5x6.5
TOKO
TOKO
TOKO
TOKO
TOKO
TOKO
FDV0630-2R2M
FDV0630-3R3M
FDV0630-4R7M
#919AS-100M
#919AS-160M
#919AS-220M
2.2µH
3.3µH
4.7µH
10µH
16µH
22µH
0.021
0.031
5.3
4.3
3.3
4.3
3.3
3.0
7.7x7x3
7.7x7x3
0.049
7.7x7x3
0.0265
0.0492
0.0776
10.3x10.3x4.5
10.3x10.3x4.5
10.3x10.3x4.5
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
10
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
Output Rectifier Diode
should be placed as close to the IC as possible.
The output rectifier diode supplies the current to
the inductor when the high-side switch is off. To
reduce losses due to the diode forward voltage
and recovery times, use a Schottky diode.
Choose a diode whose maximum reverse
voltage rating is greater than the maximum
input voltage, and whose current rating is
greater than the maximum load current. Table 3
When using ceramic capacitors, make sure that
they have enough capacitance to provide
sufficient charge to prevent excessive voltage
ripple at input. The input voltage ripple caused
by capacitance can be estimated by:
⎛
⎞
⎟
⎟
⎠
ILOAD
VOUT
VIN
VOUT
⎜
ΔV
=
×
× 1−
IN
⎜
⎝
fS × C1
V
IN
lists
manufacturers.
example
Schottky
diodes
and
Where CIN is the input capacitance value.
Output Capacitor
Table 3—Output Diodes
The output capacitor is required to maintain the
DC output voltage. Ceramic, tantalum, or low
ESR electrolytic capacitors are recommended.
Low ESR capacitors are preferred to keep the
output voltage ripple low. The output voltage
ripple can be estimated by:
Voltage Current
Part
Manufacturer
Rating Rating Package
Number
(V)
(A)
B240A-
13-F
Diodes Inc.
Diodes Inc.
Central semi
Central semi
40V
2A
SMA
SMA
SMA
SMA
B340A-
13-F
CMSH2-
40M
CMSH3-
40MA
40V
40V
40V
3A
2A
3A
⎛
⎜
⎝
⎞
⎟
⎟
⎛
⎜
⎝
⎞
⎟
⎟
⎠
VOUT
VOUT
VIN
1
⎜
⎜
ΔVOUT
=
× 1−
× RESR
+
fS × L1
8 × fS × C2
⎠
Where L is the inductor value, CO is the output
capacitance value, and RESR is the equivalent
series resistance (ESR) value of the output
capacitor.
Input Capacitor
The input current to the step-down converter is
discontinuous, therefore a capacitor is required
to supply the AC current to the step-down
converter while maintaining the DC input
voltage. Use low ESR capacitors for the best
performance. Ceramic capacitors are preferred,
but tantalum or low-ESR electrolytic capacitors
may also suffice. Since the input capacitor
absorbs the input switching current it requires
an adequate ripple current rating. The RMS
current in the input capacitor can be estimated
by:
In the case of ceramic capacitors, the
impedance at the switching frequency is
dominated by the capacitance. The output
voltage ripple is mainly caused by the
capacitance. For simplification, the output
voltage ripple can be estimated by:
⎛
⎜
⎝
⎞
⎟
⎟
⎠
VOUT
8 × fS2 × L1× C2
VOUT
⎜
ΔVOUT
=
× 1−
V
IN
In the case of tantalum or electrolytic capacitors,
the ESR dominates the impedance at the
switching frequency. For simplification, the
output ripple can be approximated to:
⎛
⎞
VOUT
VIN
VOUT
VIN
⎜
⎟
IC1 = ILOAD
×
× 1−
⎜
⎝
⎟
⎠
The worse case condition occurs at VIN = 2VOUT,
where:
VOUT
VOUT
⎛
⎞
⎟
ΔVOUT
=
× 1−
× R
ESR
⎜
ILOAD
fS × L1
VIN
⎝
⎠
IC1
=
2
The characteristics of the output capacitor also
affect the stability of the regulation system. The
MPQ4458 can be optimized for a wide range of
capacitance and ESR values.
For simplification, choose the input capacitor
whose RMS current rating greater than half of
the maximum load current. The input capacitor
can be electrolytic, tantalum or ceramic. When
using electrolytic or tantalum capacitors, a small,
high quality ceramic capacitor, i.e. 0.1μF,
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
11
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
Compensation Components
The goal of compensation design is to shape
the converter transfer function to get a desired
loop gain. The system crossover frequency
where the feedback loop has the unity gain is
important. Lower crossover frequencies result
in slower line and load transient responses,
while higher crossover frequencies could cause
system unstable. A good rule of thumb is to set
the crossover frequency to approximately one-
tenth of the switching frequency or lower. The
Table 4 lists the typical values of compensation
components for some standard output voltages
with various output capacitors and inductors.
The values of the compensation components
have been optimized for fast transient
responses and good stability at given conditions.
MPQ4458 employs current mode control for
easy compensation and fast transient response.
The system stability and transient response are
controlled through the COMP pin. COMP pin is
the output of the internal error amplifier. A
series capacitor-resistor combination sets a
pole-zero
combination
to
control
the
characteristics of the control system. The DC
gain of the voltage feedback loop is given by:
VFB
AVDC = RLOAD × GCS × AVEA
×
VOUT
Where AVEA is the error amplifier voltage gain,
GCS is the current sense transconductance, and
RLOAD is the load resistor value. The system has
two poles of importance. One is due to the
compensation capacitor (C3), the output
resistor of error amplifier. The other is due to
the output capacitor and the load resistor.
These poles are located at:
Table 4—Compensation Values for Typical
Output Voltage/Capacitor Combinations
VOUT
L
CO
R3
C3
C6
47µF
ceramic
1.8V 4.7µH
105k 100pF None
54.9k 220pF None
68.1k 220pF None
100k 150pF None
147k 150pF None
GEA
fP1
=
4.7µH-
2.5V
22µF
6.8µH ceramic
2π× C3× AVEA
and
6.8µH-
10µH
22µF
ceramic
3.3V
5V
1
fP2
=
2π × C2 × RLOAD
15µH-
22µH
22µF
ceramic
The system has one zero of importance, due to
the compensation capacitor (C3) and the
compensation resistor (R3). This zero is located
22µH-
33µH
22µF
ceramic
12V
at:
Note: The selection of L is based on fs =
500kHz. Please refer to “Inductor section” on
page7 to select proper inductor if fs is higher
than that.
To optimize the compensation components for
conditions not listed in Table 3, the following
procedure can be used.
1
2π× C3×R3
fZ1
=
The system may have another zero of
importance, if the output capacitor has a large
capacitance and/or a high ESR value. The zero,
due to the ESR and capacitance of the output
capacitor, is located at:
1. Choose the compensation resistor (R3) to set
the desired crossover frequency. Determine the
R3 value by the following equation:
1
fESR
=
2π × C2× RESR
In this case (as shown in Figure 2), a third pole
set by the compensation capacitor (C6) and the
compensation resistor (R3) is used to
compensate the effect of the ESR zero on the
loop gain. This pole is located at:
2π × C2 × fC VOUT
R3 =
×
GEA × GCS
VFB
Where fC is the desired crossover frequency
(which typically has a value no higher than
1/10th of switching frequency).
1
fP3
=
2π × C6 × R3
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
12
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
Since the internal bootstrap circuitry has higher
2. Choose the compensation capacitor (C3) to
impedance, which may not be adequate to
charge the bootstrap capacitor during each
charging period, an external bootstrap charging
diode is strongly recommended if the switching
frequency is above 2MHz (see External
achieve the desired phase margin. For
applications with typical inductor values, setting
the compensation zero, fZ1, below one forth of
the crossover frequency provides sufficient
phase margin. Determine the C3 value by the
following equation:
Bootstrap
Diode
section
for
detailed
implementation information).
4
C3 >
With higher switching frequencies, the inductive
reactance (XL) of a capacitor dominates, such
that the ESL of the input/output capacitor
determines the input/output ripple voltage at
higher switching frequencies. As a result, high
frequency ceramic capacitors are strongly
recommended as input decoupling capacitors
and output filtering capacitors.
2π × R3 × fC
Where R3 is the compensation resistor value.
3. Determine if the second compensation
capacitor (C6) is required. It is required if the
ESR zero of the output capacitor is located at
less than half of the switching frequency, or the
following relationship is valid:
Layout becomes more important when the
device switches at higher frequency. It is
essential to place the input decoupling
capacitor, catch diode and the MPQ4458 as
close together as possible, with traces that are
very short and fairly wide. This can help to
greatly reduce the voltage spikes on SW and
also lower the EMI noise level.
fS
1
<
2π × C2× RESR
2
If this is the case, then add the second
compensation capacitor (C6) to set the pole fP3
at the location of the ESR zero. Determine the
C6 value by the equation:
C2 × RESR
C6 =
R3
High Frequency Operation
The switching frequency of MPQ4458 can be
programmed up to 4MHz by an external resistor.
Please pay attention to the following if the
switching frequency is above 2MHz.
The minimum on time of MPQ4458 is about
80ns (typ). Pulse skipping operation can be
seen more easily at higher switching frequency
due to the minimum on time. Recommended
operating voltage at 4MHz is 12V or below, and
24V or below at 2MHz.
Input Max vs
Switching Frequency
30
25
20
V
=3.3V
O
15
10
5
V
=2.5V
O
1.5
2.0
2.5
3.0
3.5
4.0
f
(MHz)
S
Figure 2—Recommended Input vs. fS
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
13
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
Try to run the feedback trace as far from the
PC Board Layout
inductor and noisy power traces as possible. It
is a good idea to run the feedback trace on the
side of the PCB opposite of the inductor with a
ground plane separating the two. The
compensation components should be placed
close to the MPQ4458. Do not place the
compensation components close to or under
the high dv/dt SW node, or inside the high di/dt
power loop. If you have to do so, the proper
ground plane must be in place to isolate these
nodes. Switching losses are expected to
increase at high switching frequencies. To help
improve the thermal conduction, a grid of
thermal vias can be created right under the
exposed pad. It is recommended that they be
small (15mil barrel diameter) so that the hole is
essentially filled up during the plating process,
thus aiding conduction to the other side. Too
large a hole can cause solder wicking problems
during the reflow soldering process. The pitch
(distance between the centers) of several such
thermal vias in an area is typically 40mil.
The high current paths (GND, IN and SW)
should be placed very close to the device with
short, direct and wide traces. The input
capacitor needs to be as close as possible to
the IN and GND pins. The external feedback
resistors should be placed next to the FB pin.
Keep the switch node traces short and away
from the feedback resistor divider and
compensation network.
External Bootstrap Diode
An external bootstrap diode may enhance the
efficiency of the regulator, the applicable
conditions of external BST diode are:
z
z
VOUT=5V or 3.3V; and
Duty cycle is high: D=
VOUT
VIN
>65%
In these cases, an external BST diode is
recommended from the output of the voltage
regulator to BST pin, as shown in Figure 3
External BST Diode
IN4148
BST
CBST
MPQ4458
5V or 3.3V
SW
+
COUT
L
Figure 3—Add Optional External Bootstrap
Diode to Enhance Efficiency
The recommended external BST diode is
IN4148, and the BST cap is 0.1~1µF.
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
14
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
PCB LAYOUT GUIDE
2) Bypass ceramic capacitors are suggested
to be put close to the VIN Pin.
PCB layout is very important to achieve stable
operation. It is highly recommended to duplicate
EVB layout for optimum performance.
3) Ensure all feedback connections are short
and direct. Place the feedback resistors
and compensation components as close to
the chip as possible.
If change is necessary, please follow these
guidelines and take Figure 4 for reference.
1) Keep the path of switching current short
and minimize the loop area formed by Input
cap, high-side MOSFET and external
switching diode.
4) Route SW away from sensitive analog
areas such as FB.
5) Connect IN, SW, and especially GND
respectively to a large copper area to cool
the chip to improve thermal performance
and long-term reliability.
C4
L1
BST
V
SW
FB
V
IN
VIN
OUT
D1
R2
C2
C1
R4
R5
EN
EN
MPQ4458
R1
COMP
FREQ
C3
R3
GND
R6
MPQ4458 Typical Application Circuit
Top Layer
Bottom Layer
Figure 4―MPQ4458 Typical Application Circuit and PCB Layout Guide
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
15
MPQ4458 –INDUSTRIAL GRADE,1A, 4MHz, 36V STEP-DOWN CONVERTER
PACKAGE INFORMATION
TQFN10 (3mm x 3mm)
2.90
3.10
0.30
0.50
1.45
1.75
PIN 1 ID
SEE DETAIL A
PIN 1 ID
MARKING
0.18
10
1
5
0.30
2.25
2.55
2.90
3.10
PIN 1 ID
INDEX AREA
0.50
BSC
6
TOP VIEW
BOTTOM VIEW
PIN 1 ID OPTION A
R0.20 TYP.
PIN 1 ID OPTION B
R0.20 TYP.
0.70
0.80
0.20 REF
0.00
0.05
SIDE VIEW
DETAIL A
NOTE:
2.90
1.70
1) ALL DIMENSIONS ARE IN MILLIMETERS.
0.70
0.25
2) EXPOSED PADDLE SIZE DOES NOT INCLUDE MOLD FLASH.
3) LEAD COPLANARITY SHALL BE 0.10 MILLIMETER MAX.
4) DRAWING CONFORMS TO JEDEC MO-229, VARIATION VEED-5.
5) DRAWING IS NOT TO SCALE.
2.50
0.50
RECOMMENDED LAND PATTERN
NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third
party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not
assume any legal responsibility for any said applications.
MPQ4458 Rev. 1.0
12/5/2012
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2012 MPS. All Rights Reserved.
16
相关型号:
MPQ4458DQT-Z-LF
Switching Regulator, Current-mode, 4900kHz Switching Freq-Max, PDSO10, 3 X 3 MM, ROHS COMPLIANT, MO-229VEED-5, TQFN-10
MPS
MPQ4459DQT
Switching Regulator, Current-mode, 4900kHz Switching Freq-Max, PDSO10, 3 X 3 MM, MO-229VEED-5, TQFN-10
MPS
MPQ4459DQT-LF
Switching Regulator, Current-mode, 4900kHz Switching Freq-Max, PDSO10, 3 X 3 MM, ROHS COMPLIANT, MO-229VEED-5, TQFN-10
MPS
MPQ4459DQT-LF-Z
Switching Regulator, Current-mode, 4000kHz Switching Freq-Max, PDSO10, 3 X 3 MM, ROHS COMPLIANT, MO-229VEED-5, TQFN-10
MPS
MPQ4459DQT-Z
Switching Regulator, Current-mode, 4900kHz Switching Freq-Max, PDSO10, 3 X 3 MM, MO-229VEED-5, TQFN-10
MPS
MPQ4459DQT-Z-LF
Switching Regulator, Current-mode, 4900kHz Switching Freq-Max, PDSO10, 3 X 3 MM, ROHS COMPLIANT, MO-229VEED-5, TQFN-10
MPS
©2020 ICPDF网 联系我们和版权申明