10AP-H10-R/C01 [MSYSTEM]

High-density Signal Conditioners 10-RACK;


型号：	10AP-H10-R/C01
厂家：	M-SYSTEM
描述：	High-density Signal Conditioners 10-RACK
文件：	总3页 (文件大小：116K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: 10AP

High-density Signal Conditioners 10-RACK

[2] OUTPUT 1

1: Open collector (max. 1 kHz)

2: 5 V pulse (max. 1 kHz)

DC/FREQUENCY CONVERTER

Functions & Features

5: Photo MOSFET relay pulse (max. 30 Hz)

• Providing two pulse rate outputs in proportion to DC input

signal

[3] OUTPUT 2

0: None

Typical Applications

1: Open collector

• Totalizing applications in combination with a counter

POWER INPUT

DC Power

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

[4] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

MODEL: 10AP–[1][2][3]–R[4]

GENERAL SPECIFICATIONS

Construction: Rack-mounted; terminal access via screw

terminals at the front and via card-edge connector at the

rear; terminal cover provided

ORDERING INFORMATION

• Code number: 10AP-[1][2][3]-R[4]

Specify a code from below for each of [1] through [4].

(e.g. 10AP-621-R/Q)

Connection

• Special input range (For codes Z & 0)

• Output frequency range (e.g. 0 – 500 Hz)

Frequencies of Output 1 and 2 are the same.

• Specify the specification for option code /Q

(e.g. /C01)

Input: M3.5 screw terminals (torque 0.8 N·m)

Output: Card-edge connector and M3.5 screw terminals

(torque 0.8 N·m)

Power input: Supplied from card-edge connector

Screw terminal: Nickel-plated steel

Housing material: Flame-resistant resin (black)

Isolation: Input to output 1 to output 2 to power

Overrange output: Approx. 0 to 120 %

Zero adjustment: 0 – 5 % (front)

[1] INPUT

Current

A: 4 – 20 mA DC (Input resistance 250 Ω)

D: 0 – 20 mA DC (Input resistance 50 Ω)

G: 0 – 1 mA DC (Input resistance 1000 Ω)

H: 10 – 50 mA DC (Input resistance 100 Ω)

Z: Specify current (See INPUT SPECIFICATIONS)

( 0 % input must be 0 mA.)

Span adjustment: 95 to 105 % (front)

INPUT SPECIFICATIONS

■ DC Current: Input resistor incorporated

Specify input resistance value for code Z.

Voltage

(R ≤ 2 W ÷ [F.S. Current] )

3: 0 – 1 V DC (Input resistance 1 MΩ min.)

4: 0 – 10 V DC (Input resistance 1 MΩ min.)

5: 0 – 5 V DC (Input resistance 1 MΩ min.)

6: 1 – 5 V DC (Input resistance 1 MΩ min.)

0: Specify voltage (See INPUT SPECIFICATIONS)

( 0 % input must be 0 V.)

■ DC Voltage: 0 – 300V DC

Minimum span: 1V

Input resistance: 1 MΩ min.

10AP SPECIFICATIONS

ES-0851 Rev.9 Page 1/3

http://www.m-system.co.jp/

MODEL: 10AP

OUTPUT SPECIFICATIONS

■ Open Collector: 30 V DC @ 100 mA (resistive load)

Frequency range: 0 – 10 pulses/hour through 1 kHz

Saturation voltage: 0.6 V DC

INSTALLATION

Current consumption: Approx. 60 mA

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Standard Rack 10BXx

When output 1 is photo MOSFET relay pulse, a timer for

output 2 is provided, which limits ON time within 75

±25msec.

Weight: 200 g (0.44 lb)

■ 5 V Pulse

PERFORMANCE in percentage of span

Accuracy: ±0.1 %

Frequency range: 0 – 10 pulses/hour through 1 kHz

Hi level: 3.0 – 5.5 V

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: Approx. 3 sec. (0 – 90 %)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 500 V AC @ 1 minute

(input to output 1 to output 2 to power)

Lo level: ≤ 0.5 V

Load resistance: 250 Ω min.

■ Photo MOSFET Relay Pulse

Frequency range: 0 – 10 pulses/hour through 30 Hz

Timer: Limits ON time within 75 ±25 msec.

Rating: 132 V AC @ 200 mA (cos ø = 1)

30 V DC @ 200 mA (resistive load)

ON resistance: ≤ 2 Ω

1500 V AC @ 1 minute (input or output or power to ground)

OUTPUT PULSE WIDTH

■ Frequency less than 500 Hz at 100% input

➞ Duty ratio 20% (See the figure below)

• Open Collector

• Voltage Pulse

OFF

H Level

L Level

20%

80%

1 / f

■ Frequency greater than 500 Hz at 100% input

➞ See the figure and equation below.

• Open Collector

• Voltage Pulse

OFF

H Level

L Level

Pulse Width

Pulse Width [millisec.] =

2.09 × 100% Frequency [kHz]

■ When OUTPUT 1 is Photo MOSFET Relay Pulse

➞ See the figure below. ON pulse width is limited

within 75 25 msec. when the output frequency

gets low (below 2 to 4 Hz).

• OUTPUT 2’s Open Collector and Photo MOSFET

Relay Pulse

OFF

1 / f

10AP SPECIFICATIONS

ES-0851 Rev.9 Page 2/3

http://www.m-system.co.jp/

MODEL: 10AP

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

7–M3.5 SCREW

8 (.31)

2–4.3 (.17) dia.

MTG HOLE

TERMINAL COVER

3 (.12)

25 (.98)

51 (2.01)

130 (5.12)

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Isolation

Timer

Low Drift

Amplifier

Voltage to

Frequency

Output

Driver

–

Divider

INPUT

OUTPUT 1

OUTPUT 2

Output

Driver

OUTPUT 2***

POWER

Input shunt resistor incorporated for current input.

** Photo MOSFET relay pulse only.

***

For 1 output channel type, OUTPUT 1 is also connected to the card-edge connector inside.

Note: The section enclosed by broken line is only for 2nd output channel.

Output Connection Examples

■ Open Collector

■ Voltage Pulse

■ Photo MOSFET Relay Pulse

• AC Powered

Relay or

Counter Coil

–

Varistor or Spark

Quenching Circuit

LOAD

• DC Powered

Relay or

Counter Coil

Spark Quenching

Diode

LOAD

Specifications are subject to change without notice.

10AP SPECIFICATIONS

ES-0851 Rev.9 Page 3/3

http://www.m-system.co.jp/

相关型号：