10FNS-H40-R/C03 [MSYSTEM]

High-density Signal Conditioners 10-RACK;


型号：	10FNS-H40-R/C03
厂家：	M-SYSTEM
描述：	High-density Signal Conditioners 10-RACK
文件：	总3页 (文件大小：94K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: 10FNS

5: 0 – 5 V DC (Load resistance 500 Ω min.)

High-density Signal Conditioners 10-RACK

6: 1 – 5 V DC (Load resistance 500 Ω min.)

SQUARE ROOT EXTRACTOR

Functions & Features

[3] OUTPUT 2

0: None

• Providing two DC outputs proportional to the root of the

input signal

Voltage

6: 1 – 5 V DC (Load resistance 5000 Ω min.)

• Low-end cutout

• Optional second channel output available at the front

terminals and at the Standard Rack connector

POWER INPUT

DC Power

Typical Applications

R: 24 V DC

• Converting differential pressure to flow

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

[4] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

GENERAL SPECIFICATIONS

Construction: Rack-mounted; terminal access via screw

terminals at the front and via card-edge connector at the

rear; terminal cover provided

MODEL: 10FNS–[1][2][3]–R[4]

ORDERING INFORMATION

• Code number: 10FNS-[1][2][3]-R[4]

Specify a code from below for each [1] through [4].

(e.g. 10FNS-6A6-R/Q)

Connection

Input: M3.5 screw terminals (torque 0.8 N·m)

Output: Card-edge connector and M3.5 screw terminals

(torque 0.8 N·m)

• Specify the specification for option code /Q

(e.g. /C01)

Power input: Supplied from card-edge connector

Screw terminal: Nickel-plated steel

Housing material: Flame-resistant resin (black)

Isolation: Input to output 1 to output 2 to power

Overrange output: Approx. 0 to 120 % at 1 – 5V

Zero adjustment: -2 to +2 % (front)

[1] INPUT

Current

A: 4 – 20 mA DC (Input resistance 87.7 Ω)

H: 10 – 50 mA DC (Input resistance 100 Ω)

Voltage

Span adjustment: 95 to 105 % (front)

Low-end cutout: Approx. 10 % (output); curve

characteristics shown in the figure below

6: 1 – 5 V DC (Input resistance 1 MΩ min.)

[2] OUTPUT 1

Current

A: 4 – 20 mA DC (Load resistance 600 Ω max.)

D: 0 – 20 mA DC (Load resistance 600 Ω max.)

G: 0 – 1 mA DC (Load resistance 12 kΩ max.)

Voltage

10%

1% INPUT

3: 0 – 1 V DC (Load resistance 100 Ω min.)

4: 0 – 10 V DC (Load resistance 1000 Ω min.)

http://www.m-system.co.jp/

10FNS SPECIFICATIONS

ES-0845 Rev.7 Page 1/3

MODEL: 10FNS

INPUT SPECIFICATIONS

■ DC Current: Input resistor incorporated

OUTPUT SPECIFICATIONS

The output turns to 0 % when the input is open.

INSTALLATION

Current consumption: Approx. 30 mA with voltage output 1

Approx. 55 mA with current output 1

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Standard Rack 10BXx

Weight: 200 g (0.44 lb)

PERFORMANCE in percentage of span

Accuracy: ±0.25 % (input 1 – 100 %)

Temp. coefficient: ±0.03 %/°C (±0.02 %/°F)

Response time: ≤ 0.5 sec. (0 – 90 %)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 500 V AC @ 1 minute

(input to output 1 to output 2 to power)

1500 V AC @ 1 minute (input or output or power to ground)

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

7–M3.5 SCREW

8 (.31)

2–4.3 (.17) dia.

MTG HOLE

TERMINAL COVER

3 (.12)

25 (.98)

51 (2.01)

130 (5.12)

http://www.m-system.co.jp/

10FNS SPECIFICATIONS

ES-0845 Rev.7 Page 2/3

MODEL: 10FNS

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Isolation

Sq. Root

Extractor

Output

Driver

–

INPUT

OUTPUT 1

OUTPUT 2

Output

Driver

–

OUTPUT 2**

POWER

* Input shunt resistor incorporated for current input.

**1 output type has the output 1 connected to the card-edge connector in parallel.

Remark 1) The section enclosed by broken line is only for 2nd output channel.

Specifications are subject to change without notice.

http://www.m-system.co.jp/

10FNS SPECIFICATIONS

ES-0845 Rev.7 Page 3/3

相关型号：