10JPA-30-R/C01 [MSYSTEM]

High-density Signal Conditioners 10-RACK;


型号：	10JPA-30-R/C01
厂家：	M-SYSTEM
描述：	High-density Signal Conditioners 10-RACK
文件：	总3页 (文件大小：94K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: 10JPA

High-density Signal Conditioners 10-RACK

[1] INPUT

1: Open collector (Excitation: 12 V @ 30 mA)

2: Voltage pulse (Excitation: 12 V @ 30 mA)

3: Mechanical contact (Excitation: 12 V @ 30 mA)

FREQUENCY TRANSMITTER

(field-programmable)

Functions & Features

• Converting the output from a pulse-type transducer into

two standard process signals

[2] OUTPUT 1

Current

• Microprocessor based

A: 4 – 20 mA DC (Load resistance 600 Ω max.)

Voltage

• Field-programmable frequency range

• Linearization available for flow compensation

• Averaging non-uniform pulses

6: 1 – 5 V DC (Load resistance 500 Ω min.)

• Excitation

[3] OUTPUT 2

0: None

• Loop testing via hand-held programmer PU-2x

• Optional second channel output available at the front

terminals and at the Standard Rack connector

Voltage

6: 1 – 5 V DC (Load resistance 5000 Ω min.)

Typical Applications

POWER INPUT

DC Power

• Positive displacement flowmeters, turbine flowmeters and

vortex flowmeters

R: 24 V DC

• Proximity switches

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

• Oval flowmeters

[4] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

RELATED PRODUCTS

• Programming Unit (model: PU-2x)

MODEL: 10JPA–[1][2][3]–R[4]

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

ORDERING INFORMATION

• Code number: 10JPA-[1][2][3]-R[4]

Specify a code from below for each [1] through [4].

(e.g. 10JPA-2A6-R/Q)

• Frequency range (e.g. 0 – 152.3 Hz)

• Linearization data (max. 16 points)

Use Ordering Information Sheet (No. ESU-1673) to specify

linearization data when the I/O signals are non-linear.

• Specify the specification for option code /Q

(e.g. /C01)

GENERAL SPECIFICATIONS

Construction: Rack-mounted; terminal access via screw

terminals at the front and via card-edge connector at the

rear; terminal cover provided

Connection

Note: Consult factory on applications with a sensor handling

periodically (& quickly) changing frequency (e.g. oval

flowmeter).

Input: M3.5 screw terminals (torque 0.8 N·m)

Output: Card-edge connector and M3.5 screw terminals

(torque 0.8 N·m)

Power input: Supplied from card-edge connector

http://www.m-system.co.jp/

10JPA SPECIFICATIONS

ES-0873 Rev.11 Page 1/3

MODEL: 10JPA

Screw terminal: Nickel-plated steel

Line voltage effect: ±0.1 % over voltage range

Housing material: Flame-resistant resin (black)

Isolation: Input to output 1 to output 2 to power

Overrange output: -10 – +120 % at 1 – 5 V

(0 – 120 % when 0 % input equals to 0 Hz.)

Linearization: 16 points max. represented as percentage of

full-scale

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 500 V AC @ 1 minute

(input to output 1 to output 2 to power)

1500 V AC @ 1 minute (input or output or power to ground)

Adjustments: Programming Unit (model: PU-2x); input

range, low-end cutout, zero and span, simulating output,

averaging nonuniform pulses, linearization data, etc.

(Refer to the users manual of JXCON for the adjustments

configurable with JXCON.)

Low-end cutout: 0 – 100 % adjustable (factory set to 0 %);

hysteresis fixed to 1 %

INPUT SPECIFICATIONS

Excitation: 12 V DC @30 mA; shortcircuit protection

Pulse width (time) requirement: 10 msec. min. at

< 20 Hz; duty ratio 20 – 80 % at ≥ 20 Hz

Offset: Max. 3 times span

■ Open Collector

Frequency range: 0 – 0.01 Hz through 25 kHz

(0 – 1 kHz will be used if not otherwise specified)

Sensing: Approx. 12 V DC @ 3 mA

ON/OFF level: ≤ 800 Ω / 2 V for ON,

≥ 1.2 kΩ / 3.6 V for OFF

■ Mechanical Contact

Frequency range: 0 – 0.01 Hz through 5 Hz

(0 – 5 Hz will be used if not otherwise specified)

Sensing: Approx. 12 V DC @ 3 mA

ON/OFF level: ≤ 800 Ω / 2 V for ON,

≥ 1.2 kΩ / 3.6 V for OFF

■ Voltage Pulse: Square or sine waveforms

Frequency range: 0 – 0.01 Hz through 25 kHz

(0 - 1 kHz will be used if not otherwise specified.)

Input amplitude: 2 – 50 Vp-p

Input impedance: 10 kΩ min.

INSTALLATION

Current consumption: Approx. 60 mA with voltage output 1

Approx. 90 mA with current output 1

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Standard Rack 10BXx

Weight: 220 g (0.49 lb)

PERFORMANCE in percentage of span

Accuracy: ±0.1 % with segment gain ≤ 1 [±0.1 % × gain]

with segment gain > 1

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: 0.5 sec. + 1 pulse cycle (0 – 90 %)

http://www.m-system.co.jp/

10JPA SPECIFICATIONS

ES-0873 Rev.11 Page 2/3

MODEL: 10JPA

DIMENSIONS unit: mm (inch)

7–M3.5 SCREW

8 (.31)

2–4.3 (.17) dia.

MTG HOLE

TERMINAL COVER

3 (.12)

25 (.98)

51 (2.01)

130 (5.12)

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Isolation

Waveform

Shaper

Digital

Computation

Output

Driver

–

INPUT

OUTPUT 1

OUTPUT 2

–

SENSOR EXCITATION

12V Supply

Output

Driver

–

MODULAR JACK

PU-2x

SERIAL TRANSMISSION LINE

OUTPUT 2**

POWER

* 4kΩ attached for open collector and mechanical contact input only.

**1 output type has the output 1 connected to the card-edge connector in parallel.

Remark 1) The section enclosed by broken line is only for 2nd output channel.

Specifications are subject to change without notice.

http://www.m-system.co.jp/

10JPA SPECIFICATIONS

ES-0873 Rev.11 Page 3/3

相关型号：