10VF-330-R [MSYSTEM]

High-density Signal Conditioners 10-RACK;


型号：	10VF-330-R
厂家：	M-SYSTEM
描述：	High-density Signal Conditioners 10-RACK
文件：	总3页 (文件大小：91K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: 10VF

D: 0 – 20 mA DC (Load resistance 600 Ω max.)

High-density Signal Conditioners 10-RACK

G: 0 – 1 mA DC (Load resistance 12 kΩ max.)

Voltage

SIGNAL TRANSMITTER

(high speed response)

3: 0 – 1 V DC (Load resistance 1000 Ω min.)

4: 0 – 10 V DC (Load resistance 10 kΩ min.)

5: 0 – 5 V DC (Load resistance 5000 Ω min.)

6: 1 – 5 V DC (Load resistance 5000 Ω min.)

4W: -10 – +10 V DC (Load resistance 10 kΩ min.)

Functions & Features

• Converts DC input from a sensor into a standard

process signal

• Isolation between input and output

• 180-microsecond response

OUTPUT 2

0: None

POWER INPUT

DC Power

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

[3] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

MODEL: 10VF–[1][2]0–R[3]

/C02: Polyurethane coating

ORDERING INFORMATION

• Code number: 10VF-[1][2]0-R[3]

Specify a code from below for each [1] through [3].

(e.g. 10VF-6A0-R/Q)

/C03: Rubber coating

GENERAL SPECIFICATIONS

Construction: Rack-mounted; terminal access via screw

terminals at the front and via card-edge connector at the

rear; terminal cover provided

• Special input range (For codes 0)

• Specify the specification for option code /Q

(e.g. /C01)

Connection

Input: M3.5 screw terminals (torque 0.8 N·m)

Output: Card-edge connector and M3.5 screw terminals

(torque 0.8 N·m)

[1] INPUT

Current

A: 4 – 20 mA DC (Input resistance 250 Ω)

D: 0 – 20 mA DC (Input resistance 50 Ω)

G: 0 – 1 mA DC (Input resistance 1000 Ω)

H: 10 – 50 mA DC (Input resistance 100 Ω)

Voltage

Power input: Supplied from card-edge connector

Screw terminal: Nickel-plated steel

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Overrange output: Approx. -10 to +120 % at 1 – 5 V

Zero adjustment: -5 to +5 %; multi-turn screwdriver

adjustments (front)

3: 0 – 1 V DC (Input resistance 1 MΩ min.)

4: 0 – 10 V DC (Input resistance 1 MΩ min.)

5: 0 – 5 V DC (Input resistance 1 MΩ min.)

6: 1 – 5 V DC (Input resistance 1 MΩ min.)

4W: -10 – +10 V DC (Input resistance 1 MΩ min.)

0: Specify voltage (See INPUT SPECIFICATIONS)

Span adjustment: 95 to 105 %; multi-turn screwdriver

adjustments (front)

INPUT SPECIFICATIONS

■ DC Current: Input resistor incorporated

■ DC Voltage: -300 – +300 V DC

Minimum span: 1 V

[2] OUTPUT 1

Current

A: 4 – 20 mA DC (Load resistance 600 Ω max.)

Offset: Max. 1.5 times span

http://www.m-system.co.jp/

10VF SPECIFICATIONS

ES-0817 Rev.11 Page 1/3

MODEL: 10VF

Input resistance: ≥ 1 MΩ

OUTPUT SPECIFICATIONS

With the input voltage code 3, 4, 5, 6 and current, the

output goes below 0 % when the input is open.

INSTALLATION

Current consumption: Approx. 35 mA for voltage output

Approx. 65 mA for current output

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Standard Rack 10BXx

Weight: 180 g (0.40 lb)

PERFORMANCE in percentage of span

Accuracy: ±0.1 %

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: Approx. 180 μsec. (0 – 90 %)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 500 V AC @ 1 minute

(input to output to power)

1500 V AC @ 1 minute (input or output or power to ground)

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

7–M3.5 SCREW

8 (.31)

2–4.3 (.17) dia.

MTG HOLE

TERMINAL COVER

3 (.12)

25 (.98)

51 (2.01)

130 (5.12)

http://www.m-system.co.jp/

10VF SPECIFICATIONS

ES-0817 Rev.11 Page 2/3

MODEL: 10VF

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Isolation

Low Drift

Amplifier

Output

Driver

–

SIGNAL

SOURCE

OUTPUT

POWER

*Input shunt resistor incorporated for current input.

Remark: This module, due to its fast-response design, does not eliminate noises included

in the input signal. Use shielded twisted-pair cable for preventing them.

Specifications are subject to change without notice.

http://www.m-system.co.jp/

10VF SPECIFICATIONS

ES-0817 Rev.11 Page 3/3

相关型号：