10VPN-2A250 [MSYSTEM]
High-density Signal Conditioners 10-RACK;
| 型号： | 10VPN-2A250 |
| 厂家： | 
M-SYSTEM |
| 描述： | High-density Signal Conditioners 10-RACK |
| 文件： | 总3页 (文件大小：97K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: 10VPN
High-density Signal Conditioners 10-RACK
[3] OPTIONS
blank: none
/Q: With options (specify the specification)
LOOP POWERED I/P TRANSDUCER
Functions & Features
• Converting a DC input into a proportional standard
pneumatic signal
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
• Loop powered
• Semiconductor pressure sensor in the feedback circuit
• High resolution
/C02: Polyurethane coating
/C03: Rubber coating
• No mounting position effect
RELATED PRODUCTS
• Standard rack with air manifold
The 10VPN must be installed in a 10-Rack series rack with
air manifold.
Typical Applications
• Converting a 4 – 20 mA from a PID controller into a
pneumatic signal
GENERAL SPECIFICATIONS
Construction: Rack-mounted; terminal access via screw
terminals at the front and via card-edge connector at the
rear
Connection
Input: M3.5 screw terminals (torque 0.8 N·m) and card-
edge connector
Pneumatic: Rc 1/4", Rc 1/8" or 1/4" NPT female
(torque ≤ 12 N·m)
MODEL: 10VPN–[1]A[2]0[3]
Material
Housing: Flame-resistant resin (black)
Base: Die cast aluminium
ORDERING INFORMATION
• Code number: 10VPN-[1]A[2]0[3]
Specify a code from below for each [1] through [3].
(e.g. 10VPN-2A2S0/Q)
Screw terminals: Nickel-plated steel
Zero adjustment: -5 to +5 % (front)
Span adjustment: 95 to 105 % (front)
• Specify the specification for option code /Q
(e.g. /C01)
INPUT SPECIFICATIONS
Equivalent input impedance: Approx. 310 Ω at 20 mA
The voltage measure at the input terminals changes
corresponding to the input signal as in the diagram below.
Be sure that the device at the input side allows the load
increase.
[1] PNEUMATIC CONNECTION
2: Rc 1/4"
5: Rc 1/8" fitting
7: 1/4" NPT fitting
approx. 6.2
INPUT
Current
6.0
A: 4 – 20 mA DC
5.8
[2] OUTPUT
1S: 19.6 – 98.1 kPa
2S: 20 – 100 kPa
approx. 5.7
4
12
20
INPUT CURRENT [mA]
3S: 20.7 – 103.4 kPa
1: 0.2 – 1.0 kgf/cm
2: 0.2 – 1.0 bar
3: 3 – 15 psig
2
http://www.m-system.co.jp/
10VPN SPECIFICATIONS
ES-0830 Rev.13 Page 1/3
MODEL: 10VPN
OUTPUT SPECIFICATIONS
■ Output:
19.6 – 98.1 kPa, 0.2 – 1.0 kgf/cm
2
20 – 100 kPa, 0.2 – 1.0 bar
20.7 – 103.4 kPa, 3 – 15 psig
The output goes below 0 % if the input loop is open.
Maximum air delivery: 60 Nl/minute (2.1 SCFM)
Maximum air exhaust: 60 Nl/minute (2.1 SCFM)
INSTALLATION
Supply pressure: 140 kPa (1.4 kgf/cm , 1.4 bar, 20 psig)
2
±10 %. Use dry air containing no carbon black or other
foreign particles. To ensure reliability use an air filter (0.01
microns).
Air consumption: 6 Nl/minute (0.21 SCFM)
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Standard Rack 10BXx
Weight: 300 g (0.66 lb)
PERFORMANCE in percentage of span
Accuracy: ±0.3 % including linearity and repeatability
Linearity: ±0.2 %
Repeatability: 0.1 %
Temp. coefficient: ±0.05 %/°C (±0.03 %/°F)
Response time: ≤ 3 sec. (0 – 90 %)
Mounting position effect: ±0.1 % (all dimensions)
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
approx.
27 (1.06)
*
20 (.79)
2–4.3 (.17) dia.
MTG HOLE
[13 (.51)]
**FITTING
OUTPUT CONNECTION
Rc 1/4”, Rc 1/8”, 1/4” NPT
5
7
6
8
4–M3.5 SCREW
3 (.12)
25 (.98)
32 (1.26)
130 (5.12)
25 (.98)
* [ ] for Rc 1/8".
**Fitting provided for Rc 1/8" or 1/4" NPT connection.
8 (.31)
http://www.m-system.co.jp/
10VPN SPECIFICATIONS
ES-0830 Rev.13 Page 2/3
MODEL: 10VPN
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
SUPPLY
PRESSURE
Pilot
Valve
OUTPUT
Semiconductor
Pressure Sensor
Z
S
–
+
Power
Supply
Deviation
Amplifier
+
7
Driver
ELECTRO-MAGNETIC
FLAPPER
INPUT
–
+
8
5
6
INPUT
MONITOR mA
(4 – 20mA DC)
When the input signal is provided from the card-edge connector,
the front terminals are not available for use.
Specifications are subject to change without notice.
http://www.m-system.co.jp/
10VPN SPECIFICATIONS
ES-0830 Rev.13 Page 3/3
相关型号：
©2020 ICPDF网 联系我们和版权申明