60S-162-K/Q [MSYSTEM]

Field Network Modules 60-UNIT Series;


型号：	60S-162-K/Q
厂家：	M-SYSTEM
描述：	Field Network Modules 60-UNIT Series
文件：	总5页 (文件大小：181K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: 60S

Field Network Modules 60-UNIT Series

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

ANALOG I/O MODULE

(Multiplex Transmission System)

/C02: Polyurethane coating

/C03: Rubber coating

Functions & Features

TERMINAL SCREW MATERIAL

/S01: Stainless steel

• Interfacing analog I/O signals from/to 10-RACK or 18-RACK

modules with Multiplex Transmission System

• Saving power and I/O wiring inside an instrumentation

panel

RELATED PRODUCTS

•Special cable (model: MCN34)

(2.83)

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection

80 (3.15)

SIN-NET, RUN contact output: Euro type connector

terminal (applicable wire size: 0.2 to 2.5 mm

2, stripped

length 7 mm)

153 (6.02)

mm (inch)

I/O: 34-pin connector (OMRON XG4A-3434)

Power input: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: I/O to SIN-NET to RUN contact output to power to

FG1

MODEL: 60S-16[1]-[2][3]

Power indicator: Red LED turns ON in normal conditions;

OFF when the voltage level becomes low.

RUN indicator: Red LED turns ON when the selfdiagnosis

proves normal, OFF in an abnormality.

■ RUN Contact Output: Contact opens at error

Rated load: 30 V DC @ 0.4 A (resistive load)

Maximum switching voltage: 125 V DC

Maximum switching power: 60 W

ORDERING INFORMATION

• Code number: 60S-16[1]-[2][3]

Specify a code from below for each [1] through [3].

(e.g. 60S-161-K/Q)

• Specify the specification for option code /Q

(e.g. /C01/S01)

Minimum load: 10 mV DC @ 1 mA

NO. OF CHANNELS

Mechanical life: 5 x 10

cycles

16: 16 points

Self-diagnosis

Communication: The receiver modules detect loss of

communication and wire break.

CPU: Watch-dog timer

[1] I/O TYPE

1: Input

2: Output

Memory: Sum check

Power voltage: Detects when the voltage supply to the

CPU drops.

[2] POWER INPUT

AC Power

K: 85 – 132 V AC

(Operational voltage range 85 – 132 V, 47 – 66 Hz)

DC Power

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

[3] OPTIONS

blank: none

/Q: With options (specify the specification)

60S SPECIFICATIONS

ES-6612 Rev.3 Page 1/5

http://www.m-system.co.jp/

MODEL: 60S

COMMUNICATION

• Output Connector Pin Assignment

Configuration: Multi-drop

PIN NO.

ASSIGNMENT

PIN NO.

ASSIGNMENT

COM

Standard: Conforms to EIA RS-422

Communication: 2-wire, half-duplex

Transmission speed: 125 kbps

Control procedure: SDLC

Output

COM

Data encoding: NRZ

COM

Protocol: SIN-NET (M-System's)

Error check: CRC

COM

Transmission distance: 500 m

Output 10

Output 11

Output 12

Output 13

Output 14

Output 15

Output 16

No connection

COM

Transmission media: Twisted-pair cable CPEV-0.9 dia.

Station No.: Rotary switch

COM

Terminator: Incorporated (remove jumper pin with those

modules not located at the end of transmission line)

COM

INPUT SPECIFICATIONS

■ Analog Input

No connection

Input range: 1 – 5 V DC

INSTALLATION

Power consumption

Input resistance: ≥ 1 MΩ

10-RACK and 18-RACK I/O modules must be isolated types.

Non-isolated modules such as 10BW and 18BW are not

usable.

•AC: Approx. 4 VA

•DC: Approx. 4 W (160 mA)

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Surface or DIN rail

• Input Connector Pin Assignment

PIN NO.

ASSIGNMENT

PIN NO.

ASSIGNMENT

COM

Input

COM

Weight: 450 g (0.99 lb)

COM

PERFORMANCE in percentage of span

A/D conversion: ±0.1 %

COM

D/A conversion: ±0.1 %

COM

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Permissible power failure duration: ≤ 10 msec.

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @ 1 minute (input or output

to SIN-NET to RUN contact output to power)

2000 V AC @ 1 minute (input or output or SIN-NET or RUN

contact output or power to FG1)

Input 10

Input 11

COM

Input 12

COM

Input 13

COM

Input 14

COM

Input 15

COM

Input 16

COM

No connection

OUTPUT SPECIFICATIONS

■ Analog Output

Output must be isolated with signal conditioners.

When the transmission line is open, the last value sampled

before failure is held.

Output range: 1 – 5 V DC

Load resistance: 20 kΩ minimum

10-RACK and 18-RACK I/O modules must be isolated types.

Non-isolated modules such as 10BW and 18BW are not

usable.

60S SPECIFICATIONS

ES-6612 Rev.3 Page 2/5

http://www.m-system.co.jp/

MODEL: 60S

DESCRIPTIONS

■ RUN Contact Output (LED) Behaviors

• Input module

The LED for the Input Modules turns ON when the network is on-line.

When there is an abnormality in the network, the LED turns OFF.

The network is reconfigured after an abnormality.

• Output module

The LED for the Output Modules turns ON when the network is on-line and the module receives data from the corresponding

Input Module.

When there is an abnormality in the network or there is no data receiving, the LED turns OFF.

■ Station Number (Address)

A) 1 input module and X output modules:

Match the address for input and output modules.

B) Computer interface:

Set address numbers to correspond with the computer as output module.

■ Transmission Time

Integrate all the transmission time for each process input module in the system.

•Analog input 16 points: 24.0 msec.

An analog module does not transmit all its signals in serial but does 1 point per each cycle. For example, when 1 contact input

module (DLA1, 32 points) and 1 analog input module (16 points) are connected, 32 point contact signal and 1 point analog

signal are transmitted in turn. One cycle time is therefore calculated as:

32 points × 1.5 msec. + 24 msec. = 72 msec.

This method is beneficial for giving a priority to contact signals which vary rapidly.

■ Applicable models for use with 60S Input Module

• 60S-162 (Ao 16 points)

• DLA1-xM1 (Ao 32 points; only the top 16 out of 32 are used)

60S SPECIFICATIONS

ES-6612 Rev.3 Page 3/5

http://www.m-system.co.jp/

MODEL: 60S

TRANSMISSION LINE CONFIGURATION

The multi-drop transmission line containing 22LA1, DLA1

and 60S modules should meet the following conditions.

Contact M-System's sales office or representatives when

designing.

A) 10 kilometers at maximum in total system.

B) 60S module plus DLA1 units: One multitransmission

line containing a 60S module can consist of a maximum

of 16 units within the total distance of 500 m.

DLA1

60S

DLA1

C) 60S modules, DLA1 units plus Repeater (model:

DAL4): DAL4 units can expand the total distance.

(6 DAL4 units max.)

DAL4

60S

DLA1

60S

D) 60S module, 22LA1 module plus DLA1 units: The

total distance of a section consisting of 60S and 22LA1

modules is less than 500 meters. They can be connected

to DLA1 units via a DLA1-7 unit.

(Eight DLA1-7 units max.)

22LA1

60S

DLA1

EXTERNAL VIEW

Modular Jack

CN1

for Factory Calibration

Power Indicator LED

RUN Indicator LED

PU-2x

I/O Connector

PWR

RUN

SIN-NET Terminals

SA1

Station No. Setting

Rotary Switches

Terminals for Terminating Resistor

RUN Contact Output

SA2

60S SPECIFICATIONS

ES-6612 Rev.3 Page 4/5

http://www.m-system.co.jp/

MODEL: 60S

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

CLAMP

(top & bottom)

7.8 (.31)

DIN RAIL

35mm wide

2–4.5 (.18) dia.

MTG HOLE

25 (.98) deep

15 10

14–M3.5

SCREW

72 (2.83)

(.55)

109 (4.29)

139 (5.47)

60 (2.36)

72 (2.83)

38 (1.50)

[3.3 (.13)]

•When mounting, no extra space is needed between units.

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Transmission

LED Station No. Setting Rotary SW

TWISTED PAIR

Isolation

−

TO OTHER

SIN-NET DEVICES

Transceiver

Circuit

Control

Circuit

A/D or D/A

Converter

JUMPER PIN *1

TERMINATING RESISTOR

To 10-RACK,

18-RACK etc.

RUN CONTACT

OUTPUT

Modular Jack

for Factory

Calibration

MODULAR JACK

SERIAL TRANSMISSION LINE

U(+)

V(−)

POWER

GROUNDING FG1

*1. When the unit is located at the end of transmission line via twisted-pair cable (= no cross-wiring), short across terminals C – D with the jumper pin (or wire) provided with the unit.

Remove the jumper pin for the one not located at the end.

Specifications are subject to change without notice.

60S SPECIFICATIONS

ES-6612 Rev.3 Page 5/5

http://www.m-system.co.jp/

相关型号：