61S-161-R [MSYSTEM]

Field Network Modules 61-UNIT Series;


型号：	61S-161-R
厂家：	M-SYSTEM
描述：	Field Network Modules 61-UNIT Series
文件：	总5页 (文件大小：155K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: 61S

Field Network Modules 61-UNIT Series

[3] OPTIONS

blank: none

/Q: With options (specify the specification)

ANALOG I/O MODULE

(Multiplex Transmission System)

Functions & Features

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

• Interfacing analog I/O signals from/to Mini-M or Pico-M

modules with Multiplex Transmission System

• Saving power and I/O wiring inside an instrumentation

panel

/C02: Polyurethane coating

/C03: Rubber coating

(1.97)

RELATED PRODUCTS

• Installation Base (model: M2BS2)

• Installation Base (model: M8BS2)

100 (3.94)

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection

115 (4.53)

SIN-NET, RUN contact output: Euro type connector

mm (inch)

terminal (applicable wire size: 0.2 to 2.5 mm

stripped length 7 mm)

I/O: Via Installation Base (model: MxBS2)

MODEL: 61S–16[1]–[2][3]

Power input: Via Installation Base (model: MxBS2)

Housing material: Flame-resistant resin (black)

Isolation: I/O to SIN-NET to RUN contact output to power

Power indicator: Red LED turns ON in normal conditions;

OFF when the voltage level becomes low.

RUN indicator: Red LED turns ON when the selfdiagnosis

proves normal, OFF in an abnormality.

ORDERING INFORMATION

• Code number: 61S-16[1]-[2][3]

Specify a code from below for each [1] through [3].

(e.g. 61S-161-K/Q)

• Specify the specification for option code /Q

(e.g. /C01)

■ RUN Contact Output: Contact opens at error

Rated load: 30 V DC @ 0.4 A (resistive load)

Maximum switching voltage: 125 V DC

NO. OF CHANNELS

Maximum switching power: 60 W

16: 16 points

Minimum load: 10 mV DC @ 1 mA

Mechanical life: 5 x 10

cycles

Self-diagnosis

[1] I/O TYPE

1: Input

Communication: The receiver modules detect loss of

communication and wire break.

CPU: Watch-dog timer

2: Output

Memory: Sum check

[2] POWER INPUT

AC Power

Power voltage: Detects when the voltage supply to the

CPU drops.

K: 85 – 132 V AC

(Operational voltage range 85 – 132 V, 47 – 66 Hz)

DC Power

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

(Specify power suffix code R (24 V DC) when the UNIT is to be

combined with the M8BS2.)

61S SPECIFICATIONS

ES-6637 Rev.2 Page 1/5

http://www.m-system.co.jp/

MODEL: 61S

Dielectric strength: 1500 V AC @ 1 minute (I/O to SIN-NET to

RUN contact output to power)

COMMUNICATION

Configuration: Multi-drop

Standard: Conforms to EIA RS-422

Communication: 2-wire, half-duplex

Transmission speed: 125 kbps

Control procedure: SDLC

Data encoding: NRZ

Protocol: SIN-NET (M-System's)

Error check: CRC

Transmission distance: 500 m

Transmission media: Twisted-pair cable CPEV-0.9 dia.

Station No.: Rotary switch

Terminator: Incorporated (remove jumper pin with those

modules not located at the end of transmission line)

INPUT SPECIFICATIONS

■ Analog Input

Input range: 1 – 5 V DC

Input resistance: ≥ 1 MΩ

(Each input must be isolated by signal conditioners. Non-

isolated modules such as M2BW and M8BW are not usable.)

A / D conversion

Moving averaging: 4 samples

Sampling rate: 160 ms

OUTPUT SPECIFICATIONS

■ Analog Output

Output range: 1 – 5 V DC

Load resistance: 20 kΩ minimum

(Output must be isolated with signal conditioners.

When the transmission line is open, the last value sampled

before failure is held. Non-isolated modules such as M2BW

and M8BW are not usable. )

INSTALLATION

Power consumption

•AC: Approx. 4 VA

•DC: Approx. 4 W (160 mA)

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Installation Base (model: MxBS2)

Weight: 250 g (0.55 lb)

PERFORMANCE in percentage of span

A/D conversion: ±0.1 %

D/A conversion: ±0.1 %

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Permissible power failure duration: ≤ 10 msec.

Insulation resistance: ≥ 100 MΩ with 500 V DC

61S SPECIFICATIONS

ES-6637 Rev.2 Page 2/5

http://www.m-system.co.jp/

MODEL: 61S

DESCRIPTIONS

■ RUN Contact Output (LED) Behaviors

• Input module

The LED for the Input Modules turns ON when the network is on-line.

When there is an abnormality in the network, the LED turns OFF.

The network is reconfigured after an abnormality.

• Output module

The LED for the Output Modules turns ON when the network is on-line and the module receives data from the corresponding

Input Module.

When there is an abnormality in the network or there is no data receiving, the LED turns OFF.

■ Station Number (Address)

A) 1 input module and X output modules:

Match the address for input and output modules.

B) Computer interface:

Set address numbers to correspond with the computer as output module.

■ Transmission Time

Integrate all the transmission time for each process input module in the system.

• Analog input 16 points: 24 msec.

An analog module does not transmit all its signals in serial but does 1 point per each cycle. For example, when 1 contact input

module (DLA1, 32 points) and 1 analog input module (16 points) are connected, 32-point contact signal and 1 point analog

signal are transmitted in turn.

One cycle time is therefore calculated as:

32 points x 1.5 msec. + 24 msec. = 72 msec.

This method is beneficial for giving a priority to contact signals which vary rapidly.

■ Applicable models for use with 61S Input Module

• 61S-162 (Ao 16 points)

• DLA1-xM1 (Ao 32 points; only the top 16 out of 32 are used)

61S SPECIFICATIONS

ES-6637 Rev.2 Page 3/5

http://www.m-system.co.jp/

MODEL: 61S

TRANSMISSION LINE CONFIGURATION

The multi-drop transmission line containing 22LA1, DLA1 and

61S modules should meet the following conditions.

Contact M-System's sales office or representatives when

designing.

A) 10 kilometers at maximum in total system.

B) 61S modules plus DLA1 units: One multitransmission

line containing a 60S module can consist of a maximum of

16 units within the total distance of 500 m.

DLA1

61S

DLA1

C) 61S modules plus DLA1 units plus Repeaters (model:

DAL4): DAL4 units can expand the total distance.

(6 DAL4 units max.)

DAL4

61S

DLA1

61S

D) 61S modules plus 22LA1 modules plus DLA1 units:

The total distance of a section consists of 61S and 22LA1

modules is less than 500 meters.

They can be connected to DLA1 units via a DLA1-7 unit.

(Eight DLA1-7 units max.)

22LA1

61S

DLA1

EXTERNAL VIEW

Modular Jack

for Factory Calibration

Power Indicator LED

RUN Indicator LED

PU-2x

PWR

RUN

SIN-NET Terminals

SA1

Station No. Setting

Rotary Switches

Terminals for Terminating Resistor

RUN Contact Output

SA2

61S SPECIFICATIONS

ES-6637 Rev.2 Page 4/5

http://www.m-system.co.jp/

MODEL: 61S

EXTERNAL DIMENSIONS unit: mm (inch)

2-M3 SCREW

(.47)

38 min

(1.50)

50 (1.97)

103 (4.06)

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Station No.

Indicator Setting Rotary

LED Switches

TWISTED-PAIR

Isolation

＋

TO OTHER

SIN-NET DEVICES

Control

Circuit

A/D or D/A

Converter

Transceiver

−

TERMINATING RESISTOR

JUMPER PIN*

To Installation Base

RUN CONTACT

OUTPUT

Modular Jack

for Factory

Calibration

MODULAR

JACK

SERIAL TRANSMISSION LINE

* When the unit is located at the end of transmission line via twisted-pair cable (= no cross-wiring),

short across terminals C - D with the jumper pin (or wire) provided with the unit.

Remove the jumper pin for the one not located at the end.

Specifications are subject to change without notice.

61S SPECIFICATIONS

ES-6637 Rev.2 Page 5/5

http://www.m-system.co.jp/

相关型号：