ANR-124-J [MSYSTEM]

Limit Alarms (potentiometer adj.) A-UNIT;


型号：	ANR-124-J
厂家：	M-SYSTEM
描述：	Limit Alarms (potentiometer adj.) A-UNIT
文件：	总4页 (文件大小：124K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: ANR

3: Lo (coil energized at alarm)

Limit Alarms (potentiometer adj.) A-UNIT

4: Lo (coil de-energized at alarm)

ANGLE SENSOR ALARM

Functions & Features

[4] POWER INPUT

AC Power

• Providing SPDT relay outputs at preset voltage level

provided from Angle Sensor (model: NRA)

• Dual (Hi/Lo) trip

B: 100 V AC

C: 110 V AC

D: 115 V AC

F: 120 V AC

G: 200 V AC

H: 220 V AC

J: 240 V AC

• Energized or de-energized coil at a tripped condition

selectable

• 50 % zero/span adjustments

• Hysteresis (deadband) adjustable

• Enclosed relays

DC Power

• Relays can be powered 110 V DC

• High-density mounting

S: 12 V DC

R: 24 V DC

V: 48 V DC

Typical Applications

• Annunciator

P: 110 V DC

• Various alarm applications

RELATED PRODUCTS

• Brushless angle sensor (model: NRA)

(1.97)

GENERAL SPECIFICATIONS

Construction: Plug-in

(3.15)

Connection: M3.5 screw terminals

Housing material: Flame-resistant resin (black)

Isolation: Input to output 1 to output 2 to power

Zero adjustment: 0 – 50 % of linearity-assured range of the

angle sensor (front)

136

(5.35)

mm (inch)

Span adjustment: 50 – 100 % of linearity-assured range of

the angle sensor (front)

MODEL: ANR-[1]1[2][3]-[4]

Setpoint adjustments: 270°-turn screwdriver adjustments

(front); 0 – 100 % independently

ORDERING INFORMATION

• Code number: ANR-[1]1[2][3]-[4]

Specify a code from below for each of [1] through [4].

(e.g. ANR-1111-B)

Hysteresis (deadband) adjustments: 1 – 100 % (front)

LEDs: LED turns on at a tripped condition; red for output 1,

green for output 2 (located behind the front cover)

Power ON timer: Relays de-energized for approx. 2 seconds

after power is turned on.

[1] ACTION

1: Direct (output increases with input increase)

INPUT SPECIFICATIONS

Input: 2 – 3 V DC (output from Angle Sensor)

Excitation: 5 V DC ±2 %

2: Reverse (output increases with input decrease)

[2] SETPOINT 1 OUTPUT

1: Hi (coil energized at alarm)

2: Hi (coil de-energized at alarm)

3: Lo (coil energized at alarm)

4: Lo (coil de-energized at alarm)

[3] SETPOINT 2 OUTPUT

1: Hi (coil energized at alarm)

2: Hi (coil de-energized at alarm)

ANR SPECIFICATIONS

ES-2116 Rev.2 Page 1/4

http://www.m-system.co.jp/

MODEL: ANR

OUTPUT SPECIFICATIONS

■ Relay Contact: 100 V AC @ 1 A (cos ø = 1)

120 V AC @ 1 A (cos ø = 1)

240 V AC @ 0.5 A (cos ø = 1)

30 V DC @ 1 A (resistive load)

Maximum switching voltage: 380 V AC or 125 V DC

Maximum switching power: 120 VA or 30 W

Minimum load: 5 V DC @ 10 mA

Mechanical life: 5 x 10 cycles

For maximum relay life with inductive loads, external

protection is recommended.

Alarm Trip Operation Terminal No. in parentheses

(9-11)ON

Output 1

(9-10)ON

(1-3)ON

Output 2

(1-2)ON

Input

(%)

▲

100

Output 2

Setpoint

Output 1

Setpoint

Trip Operation in Power Failure

• Output Code: 1 & 4: Terminals 1 – 2, 9 – 10 turn ON

• Output Code: 2 & 3: Terminals 1 – 3, 9 – 11 turn ON

INSTALLATION

Power input

• AC: Operational voltage range: rating ±10 %,

50/60 ±2 Hz, approx. 2 VA

• DC: Operational voltage range: rating ±10 %, or 85 – 150

V for 110 V rating (ripple 10 % p-p max.)

approx. 2 W (80 mA at 24 V)

Operating temperature: -5 to +60°C (23 to 140°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 450 g (0.99 lb)

PERFORMANCE in percentage of span

Trip point repeatability: ±0.5 %

Temp. coefficient: ±0.05 %/°C (±0.03 %/°F)

Response time: Approx. 0.5 sec. (0 – 100 % at 90 %

setpoint)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output 1

to output 2 to power to ground)

ANR SPECIFICATIONS

ES-2116 Rev.2 Page 2/4

http://www.m-system.co.jp/

MODEL: ANR

EXTERNAL VIEW

Input Monitor

Span Adj.

Zero Adj.

No.1 Setpoint Adj.

No.1 LED

No.1 Hysteresis (Deadband) Adj.

No.2 Hysteresis (Deadband) Adj.

No.2 LED

No.2 Setpoint Adj.

Front Cover (open)

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

CLAMP

(top & bottom)

7.8 (.31)

DIN RAIL

35mm wide

2–

4.5 (.18) dia.

MTG HOLE

25 (.98) deep

10 11

–M3.5

SCREW

50 (1.97)

107 (4.21)

136 (5.35)

40 (1.57)

50 (1.97)

[3.3 (.13)]

• When mounting, no extra space is needed between units.

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

■ Relay Protection

• AC Powered

SETPOINT

MONITOR

HYSTERESIS

(DEADBAND)

Inductive

Load (Coil)

red

EXC

INP

Varistor or Spark

Quenching Circuit

yellow

ANGLE

SENSOR

LOAD

Low Drift

Amplifier

Comparator

SETPOINT 1

OUTPUT

white COM

• DC Powered

Inductive

Load (Coil)

Exc. Volt.

Generator

Diode, Varistor or

CR Circuit

Comparator

SETPOINT 2

OUTPUT

LOAD

SETPOINT HYSTERESIS

(DEADBAND)

U(+)

V(–)

POWER

Base Socket

*Relay status for output codes “1” & “4”, at power OFF.

ANR SPECIFICATIONS

ES-2116 Rev.2 Page 3/4

http://www.m-system.co.jp/

MODEL: ANR

Specifications are subject to change without notice.

ANR SPECIFICATIONS

ES-2116 Rev.2 Page 4/4

http://www.m-system.co.jp/

相关型号：