JARP2-FM-R [MSYSTEM]

Plug-in Signal Conditioners M-UNIT;


型号：	JARP2-FM-R
厂家：	M-SYSTEM
描述：	Plug-in Signal Conditioners M-UNIT
文件：	总4页 (文件大小：139K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: JARP2

B: 2 – 10 mA DC (Input resistance 500 Ω)

Plug-in Signal Conditioners M-UNIT

C: 1 – 5 mA DC (Input resistance 1000 Ω)

D: 0 – 20 mA DC (Input resistance 50 Ω)

E: 0 – 16 mA DC (Input resistance 62.5 Ω)

F: 0 – 10 mA DC (Input resistance 100 Ω)

G: 0 – 1 mA DC (Input resistance 1000 Ω)

H: 10 – 50 mA DC (Input resistance 100 Ω)

Z: Specify current (See INPUT SPECIFICATIONS)

Voltage

DC/2-PHASE PULSE CONVERTER

(field-programmable)

Functions & Features

• Providing pulse rate outputs in 90-degree phase angle in

proportion to DC input signal

• Parameters are field-programmable via hand-held

programmer PU-2x

1: 0 – 10 mV DC (Input resistance 10 kΩ min.)

2: 0 – 100 mV DC (Input resistance 100 kΩ min.)

3: 0 – 1 V DC (Input resistance 1 MΩ min.)

4: 0 – 10 V DC (Input resistance 1 MΩ min.)

5: 0 – 5 V DC (Input resistance 1 MΩ min.)

6: 1 – 5 V DC (Input resistance 1 MΩ min.)

4W: -10 – +10 V DC (Input resistance 1 MΩ min.)

0: Specify voltage (See INPUT SPECIFICATIONS)

• Isolation up to 2000 V AC

• High-density mounting

Typical Applications

• Remote transmission of rotary encoder signal via 4 – 20

mA cable in combination with the JRP2

(1.97)

[2] OUTPUT

A: Open collector

M: 5 V pulse

(3.15)

N: 12 V pulse

P: 24 V pulse

136

(5.35)

J: RS-422 line driver pulse

mm (inch)

[3] POWER INPUT

AC Power

MODEL: JARP2–[1][2]–[3][4]

M2: 100 – 240 V AC

DC Power

ORDERING INFORMATION

• Code number: JARP2–[1][2]–[3][4]

S: 12 V DC

R: 24 V DC

Specify a code from below for each of [1] through [4].

(e.g. JARP2-6A-S/Q)

P: 110 V DC

• Special input range (For codes Z & 0)

• Use Ordering Information Sheet (No. ESU-1570). Default

setting (table below) will be used if not otherwise specified.

• Specify the specification for option code /Q

(e.g. /C01/S01)

[4] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

ITEM

DEFAULT

Output zero frequency

Output span frequency

-1 kHz

1 kHz

/C02: Polyurethane coating

Alarm setpoint

Alarm hysteresis

Alarm mode

100.00%

1.00%

No alarm

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

Power ON-delay time

3.0 sec.

RELATED PRODUCTS

• Programming Unit (model: PU-2x)

[1] INPUT

Current

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

A: 4 – 20 mA DC (Input resistance 250 Ω)

A1: 4 – 20 mA DC (Input resistance 50 Ω)

JARP2 SPECIFICATIONS

ES-1570 Rev.6 Page 1/4

http://www.m-system.co.jp/

MODEL: JARP2

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

RNG6 100 mHz: -200 – +200 mHz

Min. span: 10 % of available frequency range

Duty ratio: 50 %

■ Open Collector: 50 V DC @50 mA (resistive load)

Saturation voltage: 0.6 V DC

■ Voltage Pulse

GENERAL SPECIFICATIONS

Construction: Plug-in

H level: Rating 5, 12 or 24 V ±10 %

L level: ≤ 0.5 V

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Load resistance: ≥ 1 kΩ (5 V), ≥ 2.4 kΩ (12 V), ≥ 4.8 kΩ (24

Housing material: Flame-resistant resin (black)

Isolation: Input to alarm output to output to power

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Alarm output: Turns on when the input goes above (high) or

below (low) setpoint

■ RS-422 Line Driver Pulse

Transmitter: Conforms to RS-422

■ Relay Contact:

100 V AC @ 1 A (cos ø = 1)

120 V AC @ 1 A (cos ø = 1)

240 V AC @ 0.5 A (cos ø = 1)

30 V DC @ 1 A (resistive load)

Maximum switching voltage: 380 V AC or 125 V DC

Maximum switching power: 120 VA or 30 W

Minimum load: 5 V DC @ 10 mA

Alarm setpoint: -5 – +105 %

Alarm deadband (hysteresis): 0 – 20 %

Output monitor LED: Red LED turns on according to the

output (phase A and B).

Power ON delay time: 2.0 to 1000.0 sec.

Software programming: Programming Unit (model: PU-2x);

(Refer to the users manual of JXCON for the adjustments

configurable with JXCON)

Mechanical life: 5 x 10 cycles (300 cycle/minute)

INSTALLATION

• Output frequency (zero and span)

• Alarm

Power input

•AC: Operational voltage range 85 – 264 V, 47 - 66 Hz;

Approx. 4.1 VA at 100 V

• Power ON delay time

• Others

Approx. 5.9 VA at 200 V

Approx. 7.7 VA at 264 V

•DC: Operational voltage range: rating ±10 %, or 85 – 150 V

for 110 V rating (ripple 10 % p-p max.)

Approx. 2.8 W (120 mA at 24 V)

INPUT SPECIFICATIONS

■ DC Current:

Shunt resistor attached to the input terminals (0.5 W)

Specify input resistance value for code Z.

■ DC Voltage: -300 – +300 V DC

Minimum span: 10 mV

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 280 g (0.62 lb)

Offset: Max. 1.5 times span

Input resistance

Span 10 – 100 mV : ≥ 10 kΩ

Span 0.1 – 1 V : ≥ 100 kΩ

PERFORMANCE in percentage of span

Accuracy

Span ≥ 1 V : ≥ 1 MΩ

Output 10 kHz range: ±0.3 %

Output ≤ 1 kHz range: ±0.1 %

Alarm setpoint accuracy: ±0.1 %

OUTPUT SPECIFICATIONS

Phase angle: ±90°

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: 0.3 sec. + (one cycle at 100 % output)

Time required from a step input (0 – 100 %) to the first

pulse output.

Forward (positive output): Phase A = Phase B + 90°

Reverse (negative output): Phase A = Phase B – 90°

Frequency range: 100 mHz to 10 kHz (RNG1 to RNG6)

[ Range name : Available frequency ]

RNG1 10 kHz: -20 – +20 kHz

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @ 1 minute (input to alarm

output to output to power to ground)

RNG2 1 kHz: -2 – +2 kHz

RNG3 100 Hz: -200 – +200 Hz

RNG4 10 Hz: -20 – +20 Hz

RNG5 1 Hz: -2 – +2 Hz

JARP2 SPECIFICATIONS

ES-1570 Rev.6 Page 2/4

http://www.m-system.co.jp/

MODEL: JARP2

EXTERNAL VIEW

DO NOT change the Output Voltage Adjuster.

Modular Jack

Span Adj.

Zero Adj.

Monitor LED (no function)

Output Monitor LED A

Output Monitor LED B

Output Voltage Adj.*

*only for voltage pulse output

OPERATION

fwd. 100 Hz

100%

ACCEL.

DECEL.

INPUT

ACCEL.

STOP

rev. -30 Hz

4mA

rev. -100 Hz

-10V

FORWARD

REVERSE

INPUT

20mA

100%

INPUT

+10V

100%

OUTPUT

EXTERNAL DIMENSIONS unit: mm (inch)

CLAMP

(top & bottom)

7.8 (.31)

DIN RAIL

35mm wide

2–

4.5 (.18) dia.

MTG HOLE

25 (.98) deep

10 11

–M3.5

SCREW

50 (1.97)

107 (4.21)

136 (5.35)

40 (1.57)

50 (1.97)

[3.3 (.13)]

• When mounting, no extra space is needed between units.

JARP2 SPECIFICATIONS

ES-1570 Rev.6 Page 3/4

http://www.m-system.co.jp/

MODEL: JARP2

TERMINAL ASSIGNMENTS unit: mm (inch)

INPUT RESISTOR

(model: REM)

10 11

Input shunt resistor attached

for current input.

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

OUT.

MON.

Isolation

Volt. / Freq.

Converter

f A

Out. Driver

–

Computation

INPUT

A OUTPUT

B OUTPUT

POWER

–

Out. Driver

ALARM OUTPUT

PU-2x

–

OUT.

MON.

MODULAR JACK

U(+)

V(–)

SERIAL TRANSMISSION LINE

Base Socket

*Input shunt resistor attached for current input.

Output Connection Examples

■ Open Collector

■ Voltage Pulse

–

■ RS-422 Line Driver Pulse

–

Specifications are subject to change without notice.

JARP2 SPECIFICATIONS

ES-1570 Rev.6 Page 4/4

http://www.m-system.co.jp/

相关型号：