M2DYH2-24A-R2/B [MSYSTEM]

Super-mini Signal Conditioners Mini-M Series;


型号：	M2DYH2-24A-R2/B
厂家：	M-SYSTEM
描述：	Super-mini Signal Conditioners Mini-M Series
文件：	总3页 (文件大小：105K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: M2DYH2

47 – 66 Hz)

DC Power

R: 24 V DC

Super-mini Signal Conditioners Mini-M Series

CURRENT LOOP SUPPLY

(applicable to HART signal, opencircuit detection selectable)

Functions & Features

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

R2: 11 – 27 V DC

(Operational voltage range 11 – 27 V, ripple 10 %p-p max.)

(Select ‘/N’ for ‘Standards & Approvals’ code.)

P: 110 V DC

• Powers a 4 – 20 mA DC current loop

• Isolates and relays HART signals

• Shortcircuit protection

(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)

• Opencircuit detection selectable

• Applicable to smart transmitters

[2] OPTIONS (multiple selections)

Opencircuit detection

Typical Applications

blank: none

• 2-wire HART transmitters

/B: Opencircuit detector

23 (.91)

Standards & Approvals (must be specified)

/N: Without CE

/CE: CE marking

Model

(2.99)

Other Options

blank: none

/Q: Option other than the above (specify the specification)

ZERO

SPAN

124

(4.88)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

mm (inch)

/C02: Polyurethane coating

MODEL: M2DYH2–24A–[1][2]

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

ORDERING INFORMATION

• Code number: M2DYH2-24A-[1][2]

Specify a code from below for each [1] and [2].

(e.g. M2DYH2-24A-M2/B/CE/Q)

GENERAL SPECIFICATIONS

Construction: Plug-in

• Specify the specification for option code /Q

(e.g. /C01/S01)

Connection: M3 screw terminals (torque 0.8 N·m)

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Overrange output: Approx. -10 to +110 %

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Opencircuit detection: Input current 0 mA when the output

loop is open.

SUPPLY OUTPUT

24: 24 V DC

INPUT

Current

4 – 20 mA DC (Input resistance approx. 250 Ω)

Photo MOS Relay ON Resistance; 3 Ω max.

OUTPUT

Current

SUPPLY OUTPUT

A: 4 – 20 mA DC (Load resistance 600 Ω max.)

225 - 600 Ω for HART communication

(across the terminals 1 – 5)

Output voltage: 24 – 28 V DC with no load

18 V DC min. at 20 mA

Current rating: ≤ 22 mA DC

• Shortcircuit Protection

[1] POWER INPUT

AC Power

Current limited: 30 mA max.

M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,

M2DYH2 SPECIFICATIONS

ES-5109 Rev.7 Page 1/3

http://www.m-system.co.jp/

MODEL: M2DYH2

Protected time duration: No limit

INPUT SPECIFICATIONS

■ DC Current: Input resistor incorporated

Input current: ≥ 0 mA

HART COMMUNICATION

Transmission gain: Approx. -3 dB (within 1 – 3 kHz)

measured with 250 Ω at output

Loop impedance: 250 Ω ±10 %

Communication directions: Bidirectional

INSTALLATION

Power Consumption

•AC:

Approx. 4 VA at 100 V

Approx. 6 VA at 200 V

Approx. 7 VA at 264 V

•DC: Approx. 3 W

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 150 g (0.33 lb)

PERFORMANCE in percentage of span

Accuracy: ±0.1 %

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: ≤ 0.5 sec. (0 – 90 %)

Line voltage effect

Supply output: ±3 % over voltage range

Output signal: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

to power to ground)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1

Installation Category II

Pollution Degree 2

Input or output to power: Reinforced insulation (300 V)

Input to output: Basic insulation (300 V)

RoHS Directive

EN 50581

M2DYH2 SPECIFICATIONS

ES-5109 Rev.7 Page 2/3

http://www.m-system.co.jp/

MODEL: M2DYH2

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

6 (.23)

DIN RAIL

35mm wide

2–4.2x5

(.17x.20)

MTG HOLE

6 (.24) deep

8–M3

SCREW

14 13

21.5 (.85) 10 (.39)

84 (3.31)

114 (4.49)

15 (.59)

[4 (.16)]

23 (.91)

• When mounting, no extra space is needed between units.

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

HART Isolation

DC Isolation

4 – 20mA DC

Output

Driver

Opencircuit

Detector

–

INPUT

250Ω

HHC

OUTPUT

2-WIRE XMTR

PWR SUPPLY

24V DC

Supply

U (+)

V (–)

HART Isolation

Base Socket

POWER

*1. Hand-held communicator

*2. Only for opencircuit detector (code /B)

■ When Used as DC Supply

■ When Used as Isolator

–

HHC INPUT

250Ω

2-WIRE

XMTR

HHC

Specifications are subject to change without notice.

M2DYH2 SPECIFICATIONS

ES-5109 Rev.7 Page 3/3

http://www.m-system.co.jp/

相关型号：