M2MNV-13-M2 [MSYSTEM]

Super-mini Signal Conditioners Mini-M Series;


型号：	M2MNV-13-M2
厂家：	M-SYSTEM
描述：	Super-mini Signal Conditioners Mini-M Series
文件：	总6页 (文件大小：134K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: M2MNV

47 – 66 Hz)

DC Power

R: 24 V DC

Super-mini Signal Conditioners Mini-M Series

ANALOG SWITCHING MODULE

Functions & Features

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

R2: 11 – 27 V DC

• Switches between two analog signal channels

• Switches/Distributes one voltage signal to two channels

(Operational voltage range 11 – 27 V, ripple 10 %p-p max.)

(Select ‘/N’ for ‘Standards & Approvals’ code.)

P: 110 V DC

Typical Applications

(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)

• Switching 1 – 5V DC signal: no contact failure that

happens when using mechanical contacts for this purpose

• Switching low-speed pulse signals

[4] OPTIONS (multiple selections)

Standards & Approvals (must be specified)

/N: Without CE

29.5 (1.16)

/CE: CE marking

Other Options

blank: none

Model

(2.99)

/Q: Option other than the above (specify the specification)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

124

(4.88)

mm (inch)

/C02: Polyurethane coating

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

MODEL: M2MNV-[1][2]-[3][4]

ORDERING INFORMATION

• Code number: M2MNV-[1][2]-[3][4]

Specify a code from below for each of [1] through [4].

(e.g. M2MNV-11-M2/CE/Q)

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3 screw terminals (torque 0.8 N·m)

Screw terminal: Chromated steel (standard) or stainless

steel

• Specify the specification for option code /Q

(e.g. /C01/S01)

Housing material: Flame-resistant resin (black)

Switching: Photo MOSFET relay

Note: Must be used with its socket. NOT installable to a

multi-unit installation base. (e.g. model: M2BS-16)

Isolation: Signal channel to switching command contact to

power

Power indicator LED: Green light turns on when the power is

supplied.

[1] SWITCHING CONTROL

1: Interlocking switching control (single-pole contact)

Status indicator LED 1: Green light turns on when the signal

channel 1 (A1-B1) is alive.

2: Independent switching control (double-pole contact)

Status indicator LED 2: Green light turns on when the signal

channel 2 (A2-B1) is alive.

[2] INPUT

1: Current signal (no receiving resistor)

2: Current signal (receiving resistor 50 Ω)

3: Voltage signal

INPUT & OUTPUT

■ Signal Channels

Max. operational voltage range: ±50 V DC (min. span 10

mV)

[3] POWER INPUT

AC Power

Max. operational current range: ±50 mA DC (min. span 1

mA)

M: 85 – 264 V AC (Operational voltage range 85 – 264 V,

47 – 66 Hz)

Max. operational frequency range: 100 Hz

Receiving resistor: 50 Ω incorporated (input code 2)

(Select ‘/N’ for ‘Standards & Approvals’ code.)

M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,

M2MNV SPECIFICATIONS

ES-5095 Rev.9 Page 1/6

http://www.m-system.co.jp/

MODEL: M2MNV

ON resistance: ≤ 50 Ω per wire

Signal channel to switching command contact: Basic

(ON resistance of photo MOSFET relay)

■ Output

insulation (300 V)

RoHS Directive

EN 50581

Current signal input (no receiving resistor):

Equal to the input signal

Current signal input (receiving resistor 50 Ω):

Voltage signal equal to [Current × 50 Ω]

Voltage signal input: Equal to the input signal

■ Switching Command: Relay or open collector

Contact detecting: 5 V DC / 1 mA

Detecting levels: ≤ 1 kΩ at ON / ≥ 10 kΩ at OFF

INSTALLATION

Power Consumption

•AC:

Approx. 3 VA at 100 V

Approx. 4 VA at 200 V

Approx. 5 VA at 264 V

•DC: Approx. 2 W

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 150 g (0.33 lb)

PERFORMANCE in percentage of span

Accuracy: ±0.1 % (input code 2)

Temp. coefficient: ±0.010 %/°C (±0.006 %/°F) (input code

Switching response time: ≤ 5 msec.

Leakage current at open circuit: ≤ 1 μA

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength:

2000 V AC @1 minute

(switching command contact to power to ground)

2000 V AC @1 minute

(signal channel to power to ground)

1500 V AC @1 minute

(signal channel to switching command contact)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1

Installation Category II

Pollution Degree 2

Signal channel or switching command contact to power:

Reinforced insulation (300 V)

M2MNV SPECIFICATIONS

ES-5095 Rev.9 Page 2/6

http://www.m-system.co.jp/

MODEL: M2MNV

EXTERNAL VIEW

• Channel 1

Status LED 1

• Channel 2

Status LED 2

Power LED

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm

6 (.24)

DIN RAIL

35mm wide

2–4.2x5

(.17x.20)

MTG HOLE

6 (.24) deep

11–M3

SCREW

11 10

21.5 (.85) 10 (.39)

84 (3.31)

114 (4.49)

22 (.87)

[4 (.16)]

29.5 (1.16)

• When mounting, no extra space is needed between units.

M2MNV SPECIFICATIONS

ES-5095 Rev.9 Page 3/6

http://www.m-system.co.jp/

MODEL: M2MNV

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

■ INTERLOCKING SWITCHING CONTROL (single-pole contact)

A1-1

A1-2

A2-1

A2-2

B1-1

B1-2

POWER STATUS STATUS

LED LED 1 LED 2

5kΩ

Photo MOSFET

Relay Driver

U(+)

V(–)

POWER

SWITCHING

COMMAND

SW1

Base Socket

*1. Provided only with the input code 2: Current signal (receiving resistor 50 Ω).

*2. Provided only with the input code 1: Current signal (no receiving resistor).

*1/*2 Not provided with the input code 3.

A1-B1 channel is connected when the SW1 is turned on (closed).

A2-B1 channel is connected when the SW1 is turned off (open).

■ INDEPENDENT SWITCHING CONTROL (double-pole contact)

A1-1

A1-2

A2-1

A2-2

B1-1

B1-2

POWER STATUS STATUS

LED LED 1 LED 2

5kΩ

Photo MOSFET

Relay Driver

U(+)

V(–)

POWER

SW1

SWITCHING

COMMAND

SW2

Base Socket

*1. Provided only with the input code 2: Current signal (receiving resistor 50 Ω).

*2. Provided only with the input code 1: Current signal (no receiving resistor).

*1/*2 Not provided with the input code 3.

A1-B1 channel is connected when the SW1 is turned on (closed).

A2-B1 channel is connected when the SW2 is turned on (closed).

M2MNV SPECIFICATIONS

ES-5095 Rev.9 Page 4/6

http://www.m-system.co.jp/

MODEL: M2MNV

SWITCHING OPERATIONS

■ INTERLOCKING SWITCHING CONTROL (single-pole contact)

Single contact is used to switch from Signal Channel 1 (A1 – B1) to Signal Channel 2 (A2 – B1) and vice versa.

CHANNEL 1 (A1)

CHANNEL 2 (A2)

Terminal 3 – 9 OFF (open)

Terminal 3 – 9 ON (closed)

OFF

Status LED turn on when the respective channels are alive.

• Switching Status

Current Signal (receiving resistor 50 Ω)

Voltage Signal

Current Signal (no receiving resistor)

Power : OFF

Switching command : OFF (open)

Power : ON

Switching command : OFF (open)

Power : ON

Switching command : ON (short)

*1. Resistor is provided only for the input code 2: Current signal (receiving resistor 50 Ω).

Transition (ON to OFF, OFF to ON) Status

Current Signal (receiving resistor 50 Ω)

Voltage Signal

Current Signal (no receiving resistor)

Power : ON

Switching command : OFF to ON

Power : ON

Switching command : ON to OFF

When the switching command contact is switched from When the switching command contact is switched from

OFF to ON or from ON to OFF, the signal channel is OFF to ON or from ON to OFF, the signal channel is

switched only after all photo MOSFET relays turn on switched only after all photo MOSFET relays turn off

(closed).

(open).

*1. Resistor is provided only for the input code 2: Current signal (receiving resistor 50 Ω).

■ INDEPENDENT SWITCHING CONTROL (double-pole contact)

Double contacts are used to independently switch Signal Channel 1 (A1 – B1) and Signal Channel 2 (A2 – B1).

CHANNEL 1 (A1)

CHANNEL 2 (A2)

Terminal 3 – 9 OFF (open)

Terminal 3 – 9 ON (closed)

Terminal 6 – 9 OFF (open)

Terminal 6 – 9 ON (closed)

OFF

----

OFF

----

Status LED turn on when the respective channels are alive.

M2MNV SPECIFICATIONS

ES-5095 Rev.9 Page 5/6

http://www.m-system.co.jp/

MODEL: M2MNV

Specifications are subject to change without notice.

M2MNV SPECIFICATIONS

ES-5095 Rev.9 Page 6/6

http://www.m-system.co.jp/

相关型号：