M2PHS2H-15C-M/N [MSYSTEM]

Super-mini Signal Conditioners Mini-M Series;


型号：	M2PHS2H-15C-M/N
厂家：	M-SYSTEM
描述：	Super-mini Signal Conditioners Mini-M Series
文件：	总5页 (文件大小：128K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: M2PHS2

F: 0 – 10 mA DC (Input resistance 100 Ω)

Super-mini Signal Conditioners Mini-M Series

G: 0 – 1 mA DC (Input resistance 1000 Ω)

H: 10 – 50 mA DC (Input resistance 100 Ω)

J: 0 – 10 μA DC (Input resistance 1000 Ω)

K: 0 – 100 μA DC (Input resistance 1000 Ω)

GW: -1 – +1 mA DC (Input resistance 1000 Ω)

FW: -10 – +10 mA DC (Input resistance 100 Ω)

Z: Specify current (See INPUT SPECIFICATIONS)

Voltage

PEAK HOLD

(with simple loop test output)

Functions & Features

• Track mode: the output follows proportionally to the input

• Peak-hold mode: responds only to an increasing signal,

holding the maximum value until a higher signal or a

command to reset is received

1: 0 – 10 mV DC (Input resistance 10 kΩ min.)

15: 0 – 50 mV DC (Input resistance 10 kΩ min.)

16: 0 – 60 mV DC (Input resistance 10 kΩ min.)

2: 0 – 100 mV DC (Input resistance 100 kΩ min.)

3: 0 – 1 V DC (Input resistance 1 MΩ min.)

4: 0 – 10 V DC (Input resistance 1 MΩ min.)

5: 0 – 5 V DC (Input resistance 1 MΩ min.)

6: 1 – 5 V DC (Input resistance 1 MΩ min.)

4W: -10 – +10 V DC (Input resistance 1 MΩ min.)

5W: -5 – +5 V DC (Input resistance 1 MΩ min.)

0: Specify voltage (See INPUT SPECIFICATIONS)

• Valley hold and peak-to-peak mode selectable

• Simple loop test output (0, 50, 100%)

Typical Applications

• Monitoring peak power consumption

• Monitoring the highest or lowest temperature

23 (.91)

Model

(2.99)

[3] OUTPUT

Current

ZERO

SPAN

124

(4.88)

A: 4 – 20 mA DC (Load resistance 750 Ω max.)

B: 2 – 10 mA DC (Load resistance 1500 Ω max.)

C: 1 – 5 mA DC (Load resistance 3000 Ω max.)

D: 0 – 20 mA DC (Load resistance 750 Ω max.)

E: 0 – 16 mA DC (Load resistance 900 Ω max.)

F: 0 – 10 mA DC (Load resistance 1500 Ω max.)

G: 0 – 1 mA DC (Load resistance 15 kΩ max.)

Z: Specify current (See OUTPUT SPECIFICATIONS)

Voltage

mm (inch)

MODEL: M2PHS2[1]-[2][3]-[4][5]

ORDERING INFORMATION

• Code number: M2PHS2[1]-[2][3]-[4][5]

Specify a code from below for each of [1] through [5].

(e.g. M2PHS2H-6A-M2/CE/Q)

1: 0 – 10 mV DC (Load resistance 10 kΩ min.)

2: 0 – 100 mV DC (Load resistance 100 kΩ min.)

3: 0 – 1 V DC (Load resistance 1000 Ω min.)

4: 0 – 10 V DC (Load resistance 10 kΩ min.)

5: 0 – 5 V DC (Load resistance 5000 Ω min.)

6: 1 – 5 V DC (Load resistance 5000 Ω min.)

4W: -10 – +10 V DC (Load resistance 10 kΩ min.)

5W: -5 – +5 V DC (Load resistance 5000 Ω min.)

0: Specify voltage (See OUTPUT SPECIFICATIONS)

• Special input and output ranges (For codes Z & 0)

• Specify the specification for option code /Q

(e.g. /C01/S01)

[1] HOLD FUNCTION

H: Peak hold

L: Valley hold

W: Peak-to-peak hold

[4] POWER INPUT

AC Power

[2] INPUT

Current

M: 85 – 264 V AC (Operational voltage range 85 – 264 V,

47 – 66 Hz)

A: 4 – 20 mA DC (Input resistance 250 Ω)

A1: 4 – 20 mA DC (Input resistance 50 Ω)

B: 2 – 10 mA DC (Input resistance 500 Ω)

C: 1 – 5 mA DC (Input resistance 1000 Ω)

D: 0 – 20 mA DC (Input resistance 50 Ω)

E: 0 – 16 mA DC (Input resistance 62.5 Ω)

(Select ‘/N’ for ‘Standards & Approvals’ code.)

M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,

47 – 66 Hz)

DC Power

R: 24 V DC

M2PHS2 SPECIFICATIONS

ES-5105 Rev.8 Page 1/5

http://www.m-system.co.jp/

MODEL: M2PHS2

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

R2: 11 – 27 V DC

■ DC Voltage: -300 – +300 V DC

Minimum span: 3 mV

(Operational voltage range 11 – 27 V, ripple 10 %p-p max.)

(Select ‘/N’ for ‘Standards & Approvals’ code.)

P: 110 V DC

Offset: Max. 1.5 times span

Input resistance

Span 3 – 10 mV : ≥ 10 kΩ

Span 10 – 100 mV : ≥ 10 kΩ

Span 0.1 – 1 V : ≥ 100 kΩ

Span ≥ 1 V : ≥ 1 MΩ

(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)

[5] OPTIONS (multiple selections)

Standards & Approvals (must be specified)

/N: Without CE

■ Hold Control

Contact rating: 5 V @ 1 mA

Detection levels: ≤ 1.25 kΩ / 1 V at ON

≥ 20 kΩ / 4 V at OFF

/CE: CE marking

Other Options

blank: none

/Q: Option other than the above (specify the specification)

OUTPUT SPECIFICATIONS

■ DC Current: 0 – 20 mA DC

Minimum span: 1 mA

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

Offset: Max. 1.5 times span

Load resistance: Output drive 15 V max.

■ DC Voltage: -10 – +12 V DC

Minimum span: 5 mV

/C02: Polyurethane coating

/C03: Rubber coating

Offset: Max. 1.5 times span

TERMINAL SCREW MATERIAL

/S01: Stainless steel

Load resistance: Output drive 1 mA max.; at ≥ 0.5 V

INSTALLATION

Power Consumption

GENERAL SPECIFICATIONS

Construction: Plug-in

•AC:

Connection: M3 screw terminals (torque 0.8 N·m)

Screw terminal: Chromated steel (standard) or stainless

steel

Approx. 3 VA at 100 V

Approx. 4 VA at 200 V

Approx. 5 VA at 264 V

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Overrange output: Approx. -10 to +120 % at 1 – 5 V

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

DIP switch setting: Selecting output options

• Output Function (normal output, or loop test output of 0%,

50% and 100%.)

•DC: Approx. 3 W

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 150 g (0.33 lb)

PERFORMANCE in percentage of span

Accuracy: ±0.1 %

• Output Limit (ON, OFF)

Hold control: Contact logic selectable by the DIP switch

setting

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: ≤ 0.5 sec. (0 – 90 %)

Status indicator LED 1: Green LED; indicates the

transmitter’s function mode (Refer to the instruction

manual.)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

to power to ground)

Status indicator LED 2: Orange LED; indicates the

transmitter’s function mode (Refer to the instruction

manual.)

STANDARDS & APPROVALS

EU conformity:

INPUT SPECIFICATIONS

■ DC Current:

EMC Directive

EMI EN 61000-6-4

Shunt resistor attached to the input terminals (0.5 W)

Specify input resistance value for code Z.

EMS EN 61000-6-2

Low Voltage Directive

M2PHS2 SPECIFICATIONS

ES-5105 Rev.8 Page 2/5

http://www.m-system.co.jp/

MODEL: M2PHS2

EN 61010-1

Measurement Category II (input)

Installation Category II (power)

Pollution Degree 2

Input or output to power: Reinforced insulation (300 V)

Input to output: Basic insulation (300 V)

RoHS Directive

EN 50581

EXTERNAL VIEW

■ FRONT VIEW

■ SIDE VIEW

Status Indicator LED2

Output Function

Setting

SW1

Status Indicator LED1

1 2 3 4

OFF

Zero Adj.

Span Adj.

Refer to the instruction manual for detailed procedures.

EXTERNAL DIMENSIONS unit: mm (inch)

6 (.23)

DIN RAIL

35mm wide

2–4.2x5

(.17x.20)

MTG HOLE

6 (.24) deep

8–M3

SCREW

14 13

21.5 (.85) 10 (.39)

84 (3.31)

114 (4.49)

15 (.59)

[4 (.16)]

23 (.91)

• When mounting, no extra space is needed between units.

M2PHS2 SPECIFICATIONS

ES-5105 Rev.8 Page 3/5

http://www.m-system.co.jp/

MODEL: M2PHS2

TERMINAL ASSIGNMENTS unit: mm (inch)

INPUT RESISTOR

(model: REM2)

14 13

Input shunt resistor attached

for current input.

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

STATUS

Isolation

Low Drift

Amplifier

Output

Driver

Hold

–

INPUT

OUTPUT

–

+5V

5kΩ

DIP SWITCH

U(+)

POWER

V(–)

HOLD CONTROL

Base Socket

*Input shunt resistor attached for current input.

M2PHS2 SPECIFICATIONS

ES-5105 Rev.8 Page 4/5

http://www.m-system.co.jp/

MODEL: M2PHS2

HOLD MODES

■ PEAK HOLD MODE

The transmitter output responds only to an increasing

signal, holding the maximum value until a higher signal or a

command to reset is received.

■ VALLEY HOLD MODE

The transmitter output responds only to a decreasing signal,

holding the minimum value until a lower signal or a

command to reset is received.

■ PEAK-TO-PEAK HOLD MODE

The transmitter output responds only when the input signal

goes over the previously monitored maximum value or goes

below the previously monitored minimum value.

The output is proportional to the peak-to-peak value,

absolute difference between the maximum and the

minimum values.

• Peak-to-Peak Hold Mode

INPUT

100%

90%

80%

70%

60%

50%

40%

30%

20%

10%

OUTPUT

100%

90%

80%

70%

60%

50%

40%

30%

20%

10%

HOLD

RESET

Specifications are subject to change without notice.

M2PHS2 SPECIFICATIONS

ES-5105 Rev.8 Page 5/5

http://www.m-system.co.jp/

相关型号：