M2VF3-4W4W-R [MSYSTEM]
Super-mini Signal Conditioners Mini-M Series;型号: | M2VF3-4W4W-R |
厂家: | M-SYSTEM |
描述: | Super-mini Signal Conditioners Mini-M Series |
文件: | 总3页 (文件大小:105K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: M2VF3
-55 – +55 V DC
Super-mini Signal Conditioners Mini-M Series
-60 – +60 V DC
-300 – +300 V DC *
-350 – +350 V DC *
-400 – +400 V DC *
-600 – +600 V DC *
-800 – +800 V DC *
SIGNAL TRANSMITTER
(high-accuracy, ultra-high speed response 30 μsec.)
Functions & Features
• Converts DC input from a sensor into a standard process
signal
* Select ‘/N’ for ‘Standards & Approvals’ code.
Multiple installation bases are unable.
• Frequency characteristics 12 kHz (-3 dB)
• 30-microsecond response
OUTPUT
Typical Applications
Voltage
• Isolation for a vibration analyzing system
• Isolation for Discharge/Charge tester
4W: -10 – +10 V DC (Load resistance 2000 Ω min.)
POWER INPUT
23 (.91)
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
Model
76
(2.99)
[2] OPTIONS (multiple selections)
Standards & Approvals (must be specified)
/N: Without CE
ZERO
SPAN
124
(4.88)
mm (inch)
/CE: CE marking
Other Options
blank: none
/Q: Option other than the above (specify the specification)
MODEL: M2VF3–[1]4W–R[2]
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
ORDERING INFORMATION
• Code number: M2VF3-[1]4W-R[2]
Specify a code from below for each of [1] and [2].
(e.g. M2VF3-04W-R/CE/Q)
/C02: Polyurethane coating
/C03: Rubber coating
• Special input range (For code 0: e.g. -164 – +164 mV DC)
• Specify the specification for option code /Q
(e.g. /C01/S01)
TERMINAL SCREW MATERIAL
/S01: Stainless steel
GENERAL SPECIFICATIONS
Construction: Plug-in
[1] INPUT
Voltage
Connection: M3 screw terminals (torque 0.8 N·m)
Screw terminal: Chromated steel (standard) or stainless
steel
2W: -100 – +100 mV DC (Input resistance 1 MΩ min.)
4W: -10 – +10 V DC (Input resistance 1 MΩ min.)
5W: -5 – +5 V DC (Input resistance 1 MΩ min.)
8W: -20 – +20 V DC (Input resistance 1 MΩ min.)
0: Specify voltage (Select input range as indicated below)
-20 – +20 mV DC
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Overrange input: -5 to +105 %
Zero adjustment: -1 to +1 %; multi-turn screwdriver
adjustments (front)
-24 – +24 mV DC
-40 – +40 mV DC
Span adjustment: 99 to 101 %; multi-turn screwdriver
adjustments (front)
-85 – +85 mV DC
-164 – +164 mV DC
Power LED: Green LED turns on when the power is supplied.
-200 – +200 mV DC
-15 – +15 V DC
-25 – +25 V DC
M2VF3 SPECIFICATIONS
ES-5107 Rev.7 Page 1/3
http://www.m-system.co.jp/
MODEL: M2VF3
INPUT SPECIFICATIONS
Input resistance: ≥ 1 MΩ (3 kΩ min. in power failure)
OUTPUT SPECIFICATIONS
Parallel load capacitance: ≤ 2000 pF
INSTALLATION
Power consumption
•DC: ≤ 0.6 W
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 150 g (0.33 lb)
PERFORMANCE in percentage of span
Accuracy: ±0.01 %
Temp. coefficient: ±0.005 %/°C (±0.003 %/°F)
Frequency characteristics: 12 kHz, -3 dB
Response time: ≤ 30 µsec. (0 – 90 %)
Line voltage effect: ±0.01 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EN 50581
EXTERNAL VIEW
Power LED
Zero Adj.
Span Adj.
M2VF3 SPECIFICATIONS
ES-5107 Rev.7 Page 2/3
http://www.m-system.co.jp/
MODEL: M2VF3
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
6 (.23)
DIN RAIL
35mm wide
4
1
5
8
2–4.2x5
(.17x.20)
MTG HOLE
6 (.24) deep
12
9
8–M3
SCREW
14 13
21.5 (.85) 10 (.39)
84 (3.31)
114 (4.49)
15 (.59)
[4 (.16)]
23 (.91)
• When mounting, no extra space is needed between units.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Power
LED
Z
S
Isolation
Output
Driver
Low Drift
Amplifier
+
+
–
+
–
1
4
5
8
9
SIGNAL SOURCE
OUTPUT
POWER
–
12
13
14
Base Socket
The M2VF3, by its fast-response feature, is not designed to eliminate noise present in the input signal. Use a shielded twisted-pair cable to
prevent noise from entering through the input wiring.
• At input signal code "0", signal source is allocated between terminals 8 and 4
when input exceeds 300V.
+
8
4
1
5
SIGNAL SOURCE
–
Specifications are subject to change without notice.
M2VF3 SPECIFICATIONS
ES-5107 Rev.7 Page 3/3
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明