M2XF2-S2V1-R/Q [MSYSTEM]

Super-mini Signal Conditioners Mini-M Series;


型号：	M2XF2-S2V1-R/Q
厂家：	M-SYSTEM
描述：	Super-mini Signal Conditioners Mini-M Series
文件：	总5页 (文件大小：121K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: M2XF2

Super-mini Signal Conditioners Mini-M Series

[2] OUTPUT

Current

Z1: Range 0 – 20 mA DC

Voltage

LINEARIZER

(PC programmable)

V1: Range -2.5 – +2.5 V DC

V2: Range -10 – +10 V DC

Functions & Features

• Accepting non-linear input and providing a linearized

output, proportional to the process variables

• 100-point calibration

(Configurator software is used to change output over the

described range of the selected suffix code. For changing

out of this range, set the Output Range Selectors inside the

unit before software adjustment.)

• PC programmable

Typical Applications

• V-notch weir

[3] POWER INPUT

• Gas analyzer

AC Power

• Irregular-shaped tank level input for volume calculation

• Square root extracting for DP transmitter

M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,

47 – 66 Hz)

(90 – 264 V for UL)

DC Power

23 (.91)

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

P: 110 V DC

(2.99)

(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)

(110 V ±10 % for UL)

124

(4.88)

[4] OPTIONS (multiple selections)

Standards & Approvals (must be specified)

/N: Without CE or UL

mm (inch)

/CE: CE marking

/UL: UL approval, CE marking

Other Options

MODEL: M2XF2–[1][2]–[3][4]

blank: none

/Q: Option other than the above (specify the specification)

ORDERING INFORMATION

• Code number: M2XF2-[1][2]-[3][4]

Specify a code from below for each [1] through [4].

(e.g. M2XF2-S2Z1-R/CE/Q)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

• Input range (e.g. 1 – 5 V DC)

• Output range (e.g. 4 – 20 mA DC)

• Specify the specification for option code /Q

(e.g. /C01/S01/SET)

/C02: Polyurethane coating

/C03: Rubber coating (UL not available)

TERMINAL SCREW MATERIAL

/S01: Stainless steel (UL not available)

EX-FACTORY SETTING

[1] INPUT

/SET: Preset according to the Ordering Information Sheet

(No. ESU-5085)

Current

Z1: Range 0 – 50 mA DC (Input resistance 100 Ω)

Voltage

S1: Range -1 – +1 V DC (Input resistance 1 MΩ min.)

S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.)

(Configurator software is used to change input over the

described range of the selected suffix code. For changing

out of this range (between S1 and S2), set the Input Range

Selector on the side of unit before software adjustment.

For a current input, set the Selector to the same setting as

for S2 and use a receiving resistor.)

RELATED PRODUCTS

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

M2XF2 SPECIFICATIONS

ES-5085 Rev.12 Page 1/5

http://www.m-system.co.jp/

MODEL: M2XF2

GENERAL SPECIFICATIONS

Construction: Plug-in

OUTPUT SPECIFICATIONS

■ DC Current

Connection: M3 screw terminals (torque 0.8 N·m)

Screw terminal: Chromated steel (standard) or stainless

steel

Operational range: 0 – 24 mA DC

Output range: 0 – 20 mA DC

Minimum span: 1 mA

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Overrange output: Approx. -15 to +115 %

(Negative current output is not provided.)

Manual zero adjustments: -5 to +5 %

(factory setting: 0 %)

Offset: Lower range can be any specific value within the

output range provided that the minimum span is

maintained.

Load resistance: Output drive 15 V max.

(e.g. 4 – 20 mA: 750 Ω [15 V ÷ 20 mA])

If not specified, the output range is 4 – 20 mA DC.

■ DC Voltage

Manual span adjustments: 95 to 105 %

(factory setting: 100 %)

Code V1 (narrow spans)

Programming: Downloaded from PC; input range, output

range, zero and span, linearization table, simulating output,

etc.

Operational range: -3 – +3 V DC

Output range: -2.5 – +2.5 V DC

Minimum span: 250 mV

Linearization: 100 points max. within the range of

-15 – +115 % input or output; represented as percentage of

full-scale

Code V2 (wide spans)

Operational range: -11.5 – +11.5 V DC

Output range: -10 – +10 V DC

Minimum span: 1 V

Status indicator LED: Blinking patterns indicate different

operating status of the transmitter.

Configurator connection: 2.5 dia. miniature jack;

RS-232-C level

Offset: Lower range can be any specific value within the

output range provided that the minimum span is

maintained.

Load resistance: Output drive 1 mA max.

(e.g. 1 – 5 V: 5000 Ω [5 V ÷ 1 mA])

If not specified, the output range is shown below.

V1: 0 – 1 V DC

INPUT SPECIFICATIONS

■ DC Current: Shunt resistor attached to the input terminals

(0.5 W)

V2: 1 – 5 V DC

Operational range: 0 – 70 mA DC with 100 Ω, 0.5 W

Input range: 0 – 50 mA DC

Minimum span: 2 mA

INSTALLATION

Offset: Lower range can be any specific value within the

input range provided that the minimum span is maintained.

If not specified, the input range is 4 – 20 mA DC.

■ DC Voltage

Power Consumption

•AC:

Approx. 3 VA at 100 V

Approx. 4 VA at 200 V

Code S1 (narrow spans)

Approx. 5 VA at 264 V

Operational range: -1.15 – +1.15 V DC

Input range: -1 – +1 V DC

•DC: Approx. 2 W

Operating temperature: -30 to +60°C (-22 to +140°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 120 g (0.26 lb)

Minimum span: 10 mV

Code S2 (wide spans)

Operational range: -11.5 – +11.5 V DC

Input range: -10 – +10 V DC

Minimum span: 100 mV

Offset: Lower range can be any specific value within the

input range provided that the minimum span is maintained.

If not specified, the input range is shown below.

S1: 0 – 100 mV DC

S2: 1 – 5 V DC

M2XF2 SPECIFICATIONS

ES-5085 Rev.12 Page 2/5

http://www.m-system.co.jp/

MODEL: M2XF2

PERFORMANCE in percentage of span

Overall accuracy:

Input accuracy + output accuracy [gain ≤ 1]

(inp. accuracy + out. accuracy) × gain [gain > 1]

Inversely proportional to the span.

Except the accuracy of input resistor.

See CALCULATION EXAMPLES OF OVERALL ACURACY.

• Input accuracy: (% of max. input range)

-1 – +1 V : ±0.01 %

-10 – +10 V : ±0.01 %

0 – 50 mA : ±0.02 %

• Output accuracy: ±0.04 % of max. output range

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) of max. span

at -5 to +55°C [23 to 131°F]

Response time: ≤ 0.9 sec. (0 – 90 %)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

to power to ground)

CALCULATION EXAMPLES OF OVERALL ACCURACY

[Example] Input Type -10 – +10 V, Input Range 1 – 5 V,

Output Type 0 – 20 mA, Output Range 4 – 20 mA

Max. Input Range (20 V) ÷ Span (4 V) × 0.01 % = 0.05 %

Max. Output Range (20 mA) ÷ Span (16 mA) × 0.04 %

= 0.05 %

Overall accuracy = 0.05 + 0.05 = ±0.10 %

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1

Installation Category II

Pollution Degree 2

Input or output to power: Reinforced insulation (300 V)

Input to output: Basic insulation (300 V)

RoHS Directive

EN 50581

Approval:

UL/C-UL nonincendive Class I, Division 2,

Groups A, B, C, and D

(ANSI/ISA-12.12.01, CAN/CSA-C22.2 No.213)

UL/C-UL general safety requirements

(UL 61010-1, CAN/CSA-C22.2 No.61010-1)

M2XF2 SPECIFICATIONS

ES-5085 Rev.12 Page 3/5

http://www.m-system.co.jp/

MODEL: M2XF2

EXTERNAL VIEW

■ FRONT VIEW (with cover open)

■ RIGHT SIDE VIEW

Configurator Jack

Status Indicator LED

Zero/Span Selector

Input Range Selector

Position L : code S1

Position H: code S2, Z1

Top: SPAN

Middle: OFF

Bottom: ZERO

ATT

[e.g.]

Output code V1

UP/DOWN Switches

SW3

SW6

SW2

The front cover cannot be turned open by 180 deg.

when there is no extra space between units.

■ LEFT SIDE VIEW

(with cover removed)

SW7

SW4

Output Range Selectors

Refer to the instruction manual for detailed procedures.

EXTERNAL DIMENSIONS unit: mm (inch)

6 (.23)

DIN RAIL

35mm wide

2–4.2x5

(.17x.20)

MTG HOLE

6 (.24) deep

8–M3

SCREW

14 13

21.5 (.85) 7.3 (.29)

86.7 (3.41)

116.7 (4.59)

15 (.59)

[4 (.16)]

23 (.91)

• When mounting, no extra space is needed between units.

M2XF2 SPECIFICATIONS

ES-5085 Rev.12 Page 4/5

http://www.m-system.co.jp/

MODEL: M2XF2

TERMINAL ASSIGNMENTS unit: mm (inch)

INPUT RESISTOR

(model: REM2)

14 13

Input shunt resistor attached

for current input.

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

STATUS

INPUT RANGE

SELECTOR

ZERO/SPAN

SELECTOR

OUTPUT RANGE

SELECTORS

Isolation

Digital

Computation

Output

Driver

–

Low Drift

Amplifier

INPUT

OUTPUT

POWER

–

UP/DOWN

SWITCHES

U(+)

V(–)

JACK

CONFIGURATOR

Base Socket

*Input shunt resistor attached for current input.

Specifications are subject to change without notice.

M2XF2 SPECIFICATIONS

ES-5085 Rev.12 Page 5/5

http://www.m-system.co.jp/

相关型号：