M6DXAS-S2-R [MSYSTEM]

Euro Terminal Ultra-Slim Signal Conditioners M6D Series;


型号：	M6DXAS-S2-R
厂家：	M-SYSTEM
描述：	Euro Terminal Ultra-Slim Signal Conditioners M6D Series
文件：	总4页 (文件大小：148K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: M6DXAS

Euro Terminal Ultra-Slim Signal Conditioners M6D Series

POWER INPUT

DC Power

R: 24 V DC

DC ALARM

(PC programmable)

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

Functions & Features

• 5.9-mm wide ultra-slim design

• Low profile allows the M6D module mounted in a 120-mm

deep panel

[2] OPTIONS

blank: none

/Q: With options (specify the specification)

• PC programmable

• High-density mounting

• Power and status indicator LEDs

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

5.9 (.23)

/C02: Polyurethane coating

EX-FACTORY SETTING

/SET: Preset according to the Ordering Information Sheet

(No. ESU-7828)

(3.70)

RELATED PRODUCTS

• PC configurator software (model: M6CFG)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

102

(4.02)

mm (inch)

MODEL: M6DXAS–[1]–R[2]

GENERAL SPECIFICATIONS

Connection

ORDERING INFORMATION

• Code number: M6DXAS-[1]-R[2]

Specify a code from below for each [1] and [2].

(e.g. M6DXAS-Z1-R/Q)

Input and output: Euro terminal (torque 0.3 N·m)

Power input: Via the Installation Base (model: M6DBS)

or Euro terminal (torque 0.3 N·m)

Applicable wire size: 0.2 to 2.5 mm , stripped length 8 mm

• Input range (e.g. 4 – 20 mA DC)

• Specify the specification for option code /Q

(e.g. /C01/SET)

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Power LED: Green light turns on when the power is supplied.

Status indicator LED: Orange LED; Blinking patterns indicate

different operating status of the transmitter.

Alarm monitor LED: Red LED turns on when the alarm is

tripped.

[1] INPUT

Current

Z1: Range 0 – 50 mA DC (Input resistance 24.9 Ω)

Voltage

Programming: Downloaded from PC

Input type and range

S1: Range -1000 – +1000 mV DC (Input resistance 1 MΩ min.)

S2: Range -10 – +10 V DC (Input resistance 1 MΩ min.)

(Configurator software is used to change input over the

described range of the selected suffix code.

For changing between suffix codes, set the Input Range

Selector on the side of unit before software adjustment.)

Input fine adjustments

Alarm setpoint (input %)

Trip action (High or Low)

Relay coil (energized or de-energized)

Power ON delay time (0 to 999 sec.)

Alarm ON delay time (0 to 999 sec.)

Hysteresis (deadband) (input %)

OUTPUT

Relay; SPDT or transfer contact

Alarm test, and others

For detailed information, refer to the users manual for the

PC configurator.

M6DXAS SPECIFICATIONS

ES-7828 Rev.8 Page 1/4

http://www.m-system.co.jp/

MODEL: M6DXAS

Configurator connection: 2.5 dia. miniature jack;

RS-232-C level

INSTALLATION

Power consumption: Approx. 0.5 W

Factory default setting

Operating temperature: -20 to +55°C (-4 to +131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Installation Base (model: M6DBS) or DIN rail

Weight: 65 g (2.3 oz)

Alarm setpoint: 80 %

Trip action: High

Relay coil at alarm: Energized

Power ON delay time: 5 sec.

Alarm ON delay time: 0 sec.

Hysteresis (deadband) : 1.0 %

PERFORMANCE in percentage of span

Setpoint accuracy (trip point accuracy) : ±0.05 %

Setpoint accuracy is inversely proportional to the input

span.

INPUT SPECIFICATIONS

■ DC Current: Input resistor incoporated

(If not specified, the input range is 4 – 20 mA DC.)

Input range: 0 – 50 mA DC

[Example] Input type 0 – 50 mA, Input range 4 – 20 mA

Max. Input Range (50 mA) ÷ Span (16 mA) × 0.05 %

= ±0.16 %

Minimum span: 2 mA

Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span

Response time: ≤ 0.2 sec. (0 – 100 % at 90 % setpoint)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

to power to ground)

Offset: Lower range can be any specific value within the

input range provided that the minimum span is maintained.

■ DC Voltage

•Code S1 (narrow spans)

Input range: -1000 – +1000 mV DC

Minimum span: 100 mV

•Code S2 (wide spans)

STANDARDS & APPROVALS

EU conformity:

Input range: -10 – +10 V DC

Minimum span: 1 V

EMC Directive

Offset: Lower range can be any specific value within the

input range provided that the minimum span is maintained.

If not specified, the input range is shown below.

S1: 0 – 100 mV DC

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1

S2: 1 – 5 V DC

Measurement Category II (output)

Pollution Degree 2

OUTPUT SPECIFICATIONS

■ Relay Output

Input or power to output: Reinforced insulation (300 V)

Input to power: Basic insulation (300 V)

RoHS Directive

Relay rating:

250 V AC @2 A (cos ø = 1)

EN 50581

30 V DC @2 A (resistive load)

Maximum switching voltage: 250 V AC or 125 V DC

Maximum switching power: 500 VA or 60 W

Minimum load: 5 V DC @100 mA

Mechanical life: 5 × 10 cycles (rate 180/min.)

Alarm Trip Operation Terminal No. in parentheses

• Setting Example

Hi alarm (coil energized at alarm) or

Lo alarm (coil de-energized at alarm)

(3–2)ON

Output

(3–4)ON

Input

(%)

100

Setpoint

Trip operation in power failure: Terminals 3 – 4 turn ON.

M6DXAS SPECIFICATIONS

ES-7828 Rev.8 Page 2/4

http://www.m-system.co.jp/

MODEL: M6DXAS

EXTERNAL VIEW

FRONT VIEW (with the cover open)

SIDE VIEW

Power LED

Alarm Monitor LED

Input Selector

Status Indicator LED

Configurator Jack

The DIP switch setting is required to select input types

before setting a precise input range using PC Configurator

Software (model: M6CFG).

Refer to the instruction manual for detailed procedures.

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

WIRE INSERTION ANGLE: approx. 7°

8–M3

EURO TERMINAL

DIN RAIL HOOK

DIN RAIL

35mm wide

SCREWDRIVER

INSERTION ANGLE

: approx. 40°

[0.5 (.02)]

5.9 (.23)

102 (4.02)

• When mounting, no extra space is needed between units.

M6DXAS SPECIFICATIONS

ES-7828 Rev.8 Page 3/4

http://www.m-system.co.jp/

MODEL: M6DXAS

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

STATUS ALARM

IND. LED MONITOR LED

INPUT

SELECTOR

N.C.

Digital

–

Computation

N.O. OUTPUT

COM

Low Drift

Amplifier

24.9 Ω

INPUT

POWER LED

POWER

–

CONFIGURATOR

JACK

POWER

■ Relay Protection

• AC Powered

• DC Powered

Inductive

Load (Coil)

Inductive

Load (Coil)

LOAD

Diode, Varistor or

CR Circuit

Varistor or CR Circuit

Specifications are subject to change without notice.

M6DXAS SPECIFICATIONS

ES-7828 Rev.8 Page 4/4

http://www.m-system.co.jp/

相关型号：