M6NXAR-4-R/Q [MSYSTEM]

Screw Terminal Ultra-Slim Signal Conditioners M6N Series;


型号：	M6NXAR-4-R/Q
厂家：	M-SYSTEM
描述：	Screw Terminal Ultra-Slim Signal Conditioners M6N Series
文件：	总4页 (文件大小：148K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: M6NXAR

0: Specify (Please provide a resistance table.)

Screw Terminal Ultra-Slim Signal Conditioners M6N Series

(Configurator software is used to change the input type and

range. Input code 7: Pt 1000 cannot be switched to/from

other input types while its temperature range can be

changed.)

RTD ALARM

(PC programmable)

Functions & Features

• 7.5-mm wide ultra-slim design

• Low profile allows the M6N module mounted in a 120-mm

deep panel

OUTPUT

Relay; SPDT or transfer contact

• PC programmable

• Linearization and upscale and downscale burnout

protection

POWER INPUT

DC Power

• High-density mounting

R: 24 V DC

• Power and status indicator LEDs

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

[2] OPTIONS

7.5 (.30)

blank: none

/Q: With options (specify the specification)

102

(4.02)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

102

(4.02)

mm (inch)

RELATED PRODUCTS

• PC configurator software (model: M6CFG)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

MODEL: M6NXAR–[1]–R[2]

ORDERING INFORMATION

• Code number: M6NXAR-[1]-R[2]

Specify a code from below for each [1] and [2].

(e.g. M6NXAR-4-R/Q)

GENERAL SPECIFICATIONS

Connection

• Temperature range (e.g. 0 – 100°C)

• Specify the specification for option code /Q

(e.g. /C01)

Input and output: M3 screw terminal (torque 0.5 N·m)

Power input: Via the Installation Base (model: M6NBS)

or M3 screw terminal (torque 0.5 N·m)

Recommended solderless terminal: Max. 5.8 mm (0.23”)

wide; Ones with insulation sleeve do not fit.

[1] INPUT RTD

1: JPt 100 (JIS'89)

Applicable wire size: 0.2 – 2.5 mm

(Usable range: -200 to +500°C, -328 to +932°F)

3: Pt 100 (JIS'89)

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

(Usable range: -200 to +650°C, -328 to +1202°F)

4: Pt 100 (JIS'97, IEC)

Burnout: Upscale standard; downscale or no burnout

optional by programming

(Usable range: -200 to +850°C, -328 to +1562°F)

5: Pt 50 Ω (JIS'81)

In case of upscale standard, the alarm operates as if the

input signal has exceeded over the range.

Linearization: Standard

(Usable range: -200 to +649 °C, -328 to +1200°F)

7: Pt 1000

Power LED: Green light turns on when the power is supplied.

Status indicator LED: Orange LED; Blinking patterns indicate

different operating status of the transmitter.

Alarm monitor LED: Red LED turns on when the alarm is

(Usable range: -200 to +850°C, -328 to +1562°F)

9: Cu 10 @25°C

(Usable range: -50 to +250°C, -58 to +482°F)

M6NXAR SPECIFICATIONS

ES-7923 Rev.4 Page 1/4

http://www.m-system.co.jp/

MODEL: M6NXAR

tripped.

Alarm Trip Operation Terminal No. in parentheses

Programming: Downloaded from PC

Input type and range

• Setting Example

Hi alarm (coil energized at alarm) or

Lo alarm (coil de-energized at alarm)

Input fine adjustments

(3–2)ON

Output

User’s RTD table (max. 300 points)

Burnout (Upscale, downscale or no burnout)

Alarm setpoint (input %)

(3–4)ON

Input

(%)

100

Trip action (High or Low)

Setpoint

Relay coil (energized or de-energized)

Power ON delay time (0 to 999 sec.)

Alarm ON delay time (0 to 999 sec.)

Hysteresis (deadband) (input %)

Alarm test, and others

Trip operation in power failure: Terminals 3 – 4 turn ON.

INSTALLATION

Power consumption: Approx. 0.5 W

Configurator connection: 2.5 dia. miniature jack;

RS-232-C level

Operating temperature: -20 to +55°C (-4 to +131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Installation Base (model: M6NBS) or DIN rail

Weight: 65 g (2.3 oz)

Factory default setting

Alarm setpoint: 80%

Trip action: High

Relay coil at alarm: Energized

Power ON delay time: 5 seconds

Alarm ON delay time: 0 seconds

Hysteresis (deadband): 1.0%

Burnout: Upscale

PERFORMANCE in percentage of span

Setpoint accuracy (trip point accuracy)

Pt and JPt: Whichever greater ±0.1 % of input range or

±0.15°C

Cu10: ±1°C

■Recommended solderless terminal (unit: mm (inch))

Temp. coefficient: ±0.01 %/°C (±0.006 %/°F) of max. span

Response time: ≤ 1 sec. (0 – 100 % at 90 % setpoint)

Burnout response time: ≤ 1 sec.

5.5 max.

(.22)

4 min.

(.16)

3.2 (.13) dia.

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

to power to ground)

INPUT SPECIFICATIONS

Input: 2- or 3-wire RTD

CALCULATION EXAMPLES OF SETPOINT ACCURACY

[Example] Input type Pt 100, Input range 0 – 100°C

Setpoint accuracy *1 (0.15°C *2) ÷ Span (100°C) × 100 %

*1. Calculate the accuracy in °C

Maximum leadwire resistance: 10 Ω per wire

Sensing current: ≤ 1.5 mA (≤ 0.15 mA for Pt 1000)

Minimum span: 20°C or 36°F

*2. 100 °C × 0.1 % = 0.1 °C ≤ 0.15 °C. 0.15 °C is used as

input accuracy value.

Resistance range:

0 - 500 Ω (Input code: 1, 3, 4, 5, 9)

0 - 5 kΩ (Input code: 7)

If not specified, the input range is 0 - 100°C.

STANDARDS & APPROVALS

EU conformity:

EMC Directive

OUTPUT SPECIFICATIONS

■ Relay Output

EMI EN 61000-6-4

EMS EN 61000-6-2

Relay rating:

Low Voltage Directive

EN 61010-1

250 V AC @2 A (cos ø = 1)

30 V DC @2 A (resistive load)

Maximum switching voltage: 250 V AC or 125 V DC

Maximum switching power: 500 VA or 60 W

Minimum load: 5 V DC @100 mA

Measurement Category II (output)

Pollution Degree 2

Input or power to output: Reinforced insulation (300 V)

RoHS Directive

Mechanical life: 5 × 10 cycles (rate 180/min.)

EN 50581

M6NXAR SPECIFICATIONS

ES-7923 Rev.4 Page 2/4

http://www.m-system.co.jp/

MODEL: M6NXAR

EXTERNAL VIEW

(With the cover open)

Power LED

Alarm Monitor LED

Status Indicator LED

Configurator Jack

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

SCREWDRIVER

INSERTION ANGLE

: approx. 55°

WIRE INSERTION ANGLE

: approx. 35°

8–M3

SCREW TERMINAL

DIN RAIL HOOK

DIN RAIL

35mm wide

[1 (.04)]

SCREWDRIVER

INSERTION ANGLE

: approx. 40°

7.5 (.30)

102 (4.02)

*Screwdriver stem diameter: 6 mm (.24”) or less

• When mounting, no extra space is needed between units.

M6NXAR SPECIFICATIONS

ES-7923 Rev.4 Page 3/4

http://www.m-system.co.jp/

MODEL: M6NXAR

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

STATUS ALARM

IND. LED MONITOR LED

RTD

2-wire

3-wire

Digital

Computation

OUTPUT

Low Drift

Amplifier

COM

POWER LED

–

POWER

CONFIGURATOR

JACK

■ Relay Protection

• AC Powered

• DC Powered

Inductive

Load (Coil)

Inductive

Load (Coil)

LOAD

Diode, Varistor or

CR Circuit

Varistor or CR Circuit

Specifications are subject to change without notice.

M6NXAR SPECIFICATIONS

ES-7923 Rev.4 Page 4/4

http://www.m-system.co.jp/

相关型号：