M8PP1-C4M2M21-R/Q [MSYSTEM]
Dual Output Super-mini Signal Conditioners Pico-M Series;
| 型号： | M8PP1-C4M2M21-R/Q |
| 厂家： | 
M-SYSTEM |
| 描述： | Dual Output Super-mini Signal Conditioners Pico-M Series |
| 文件： | 总5页 (文件大小：125K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: M8PP1
Max. 50 kHz for AC voltage pulse input
Dual Output Super-mini Signal Conditioners Pico-M Series
[4] OUTPUT PULSE WIDTH
1: Equal to the input
PULSE ISOLATOR
(built-in excitation, CE)
2: One-shot output (std. pulse width 50 msec.)
Specify when optional pulse width is required.
Functions & Features
• Amplifying, waveshaping a pulse rate input and providing
two galvanically isolated pulse signals
• Space-saving, easy-to-maintain, multi-channel installation
base
POWER INPUT
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[5] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
MODEL: M8PP1-[1][2][3][4]-R[5]
/C02: Polyurethane coating
ORDERING INFORMATION
• Code number: M8PP1-[1][2][3][4]-R[5]
Specify a code from below for each of [1] through [5].
(e.g. M8PP1-B7A1A12-R/Q)
/C03: Rubber coating
RELATED PRODUCTS
• Installation Base or Single Mount Base Socket (model:
• Input frequency (e.g. 0 – 1000 Hz)
• Output pulse width (e.g. 75 msec.)
Use Ordering In-formation Sheet (No. ESU-5484) for Input
Codes B:DC voltage pulse or E: AC voltage pulse, or for non-
standard output pulse width.
M8BSx)
This unit must be mounted on dedicated base or socket
except Model M8BS2 base.
• Specify the specification for option code /Q
(e.g. /C01 )
GENERAL SPECIFICATIONS
Construction: Plug-in
Mounting screw: M3 screw (torque 0.3 N·m)
Housing material: Flame-resistant resin (black)
Power supply: Via the Installation Base terminals
(model: M8BSx)
[1] INPUT
A: Dry contact
B: DC voltage pulse (Specify sensitivity)
C: 5 V pulse (sensitivity 2 V)
D: 12 V/24 V pulse (sensitivity 5 V)
E: AC voltage pulse (Specify sensitivity)
H: Two-wire current pulse
Isolation: Input to output 1 to output 2 to power
Polarity switch: Inverting output pulse logic
(factory setting: non-inverted)
Input pulse sensing: DC coupled (AC coupled for AC voltage
pulse)
[2] EXCITATION
0: None
INPUT SPECIFICATIONS
Excitation: 12 V DC ±2 V @30 mA
4: 12 V DC / 30 mA
7: 24 V DC / 30 mA
24 V DC ±4 V @30 mA
shortcircuit protection; approx. ≤ 5 mA at shortcircuit
Caution: With a current exceeding 30 mA, the pulse isolator
stops feeding the sensor excitation, until the sensor is
removed and connected again.
[3] OUTPUT 1 / OUTPUT 2
A1A1: Open collector / open collector (max. 100 kHz)
A2A2: Open collector / open collector (max. 10 Hz)
M1M1: 5 V pulse / 5 V pulse (max. 100 kHz)
M2M2: 5 V pulse / 5 V pulse (max. 10 Hz)
Pulse width time requirement
No pulse width adj. for output: 2 µsec. min.
M8PP1 SPECIFICATIONS
ES-5378 Rev.5 Page 1/5
http://www.m-system.co.jp/
MODEL: M8PP1
I Pulse
• DC Voltage Pulse
(10 msec. min. for 0 – 10 Hz)
One-shot: 1 msec. min.
Volts
50V max.
VH
VL
■ Dry Contact
Max. frequency: 100 kHz
Sensing: Approx. 12 V DC @3 mA
ON/OFF level: ≥ 4 kΩ/6 V at OFF
≤ 1.3 kΩ/4 V at ON
Amplitude
Vinp-p
DC Offset
Detecting
Level
■ DC Voltage Pulse: Specify detecting level, amplitude and
DC offset.
t
• AC Voltage Pulse
Volts
Max. frequency: 100 kHz
Waveform: Square or sine
Input impedance: 30 kΩ min.
Input amplitude: 2 – 50 V p-p
50V max.
VH
VL
t
Amplitude
Vinp-p
Detecting level: 2 – 10 V; 0.6 V ≤ V
H
– V ≤ 1.3 V
L
Max. voltage between input terminals: 50 V
• 5 V, 12 V, 24 V Pulse
• Two-wire Current Pulse
Current
Max. frequency: 100 kHz
I H
I L
Amplitude
I inp-p
Waveform: Square or sine
Input impedance: 30 kΩ min.
Detecting H level
Detecting
Level
0mA
5 V pulse: ≥ 3 V
t
12 V, 24 V pulse: ≥ 6 V
Detecting L level
5 V pulse: ≤ 1 V
OUTPUT SPECIFICATIONS
Max. frequency: 100 kHz
■ Open Collector: 50 V DC @50 mA
Saturation voltage: 0.5 V DC
■ 5 V Pulse
12 V, 24 V pulse: ≤ 4 V
■ AC Voltage Pulse: Specify amplitude and frequency.
Max. frequency: 50 kHz
Min. frequency: 1 Hz
Waveform: Sine
Hi level: 5 V ±10 %
Input impedance: 10 kΩ min.
Input amplitude: 0.1 – 100 V p-p
Max. voltage between input terminals: 50 V
■ Two-wire Current Pulse
Max. frequency: 100 kHz
Lo level: ≤ 0.5 V
Load resistance: 1000 Ω min.
OUTPUT PULSE WIDTH
Input resistance: Receiving resistor 250 Ω
Input range: 0 – 25 mA
• One-shot Output: Constant pulse width
Output Frequency (Hz) = 500 ÷ Output Pulse Width (msec.)
Pulse width: 1 – 500 msec. (standard 50 msec. ±20 %)
Detecting level: ≤ 4 mA for Lo, ≥ 12 mA for Hi
INSTALLATION
Current consumption: Approx. 90 mA
Operating temperature: 0 to 55°C (32 to 131°F)
Operating humidity: 30 to 95 %RH (non-condensing)
Mounting: Installation Base (model: M8BSx)
Weight: 70 g (2.5 oz)
M8PP1 SPECIFICATIONS
ES-5378 Rev.5 Page 2/5
http://www.m-system.co.jp/
MODEL: M8PP1
PERFORMANCE
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength:
1500 V AC @1 minute (input to output 1 or output 2 or
power to ground)
500 V AC @1 minute (output 1 to output 2 to power)
SWC test: ANSI/IEEE-C37.90.1-1989
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EN 50581
FRONT VIEW
• Polarity SW
Used to select output pulse logic.
Push in the switch to invert the output logic.
Push back for non-inverted output.
Polarity SW
OUTPUT LOGIC
VOLTAGE PULSE
OUTPUT
OPEN COLLECTOR
OFF
INPUT TYPE
PULSE LOGIC
Non Inverted
INPUT
H
H
DC Voltage Pulse Input
2-wire Current Pulse Input
ON current (H)
L
L
ON
H
H
OFF
Inverted
Non Inverted
Inverted
OFF current (L)
L
L
ON
OFF
H
OFF
ON
L
ON
Dry Contact Input
AC Voltage Pulse
OFF
H
OFF
ON
L
ON
H
OFF
Non Inverted
Inverted
L
ON
H
OFF
L
ON
The pulse width in one-shot means the bold lined section of a pulse waveform.
M8PP1 SPECIFICATIONS
ES-5378 Rev.5 Page 3/5
http://www.m-system.co.jp/
MODEL: M8PP1
EXTERNAL DIMENSIONS unit: mm (inch)
I/O PINS
17.5(.69)
75 (2.95)
83 (3.27)
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Isolation
Output
Driver
6
7
+
OUTPUT 1
–
POLARITY SW
N
5
1
2
4
3
**
Waveform
Shaper
Polarity
Inverter
Output
Driver
+
–
+
A
B
C
D
R
8
9
+
One-Shot
INPUT
OUTPUT 2
–
SENSOR EXC.
*
Excitation
Supply
10
11
+
POWER
–
Installation Base
* Provided only when the sensor excitation option is selected.
**Provided only when the one-shot output option is selected.
Input Connection Examples
Output Connection Examples
■ Dry Contact
+12V
■ 2-Wire Current Pulse
• Built-in Excitation
■ Open Collector
■ Voltage Pulse
4k
Ω
250
Ω
+
–
A
B
C
–
+
A
B
C
6
7
8
9
+
–
+
–
+
–
+
–
6
7
8
9
+
–
+
–
+
–
+
–
2-WIRE
PICK-UP
–
PWR
+
Vsns
Vsns
■ DC Voltage Pulse
• External DC Supply
250
Ω
+
–
–
+
A
B
C
–
+
A
B
C
2-WIRE
PICK-UP
DC SUPPLY
Vsns
Vsns
PWR
+
–
■ AC Voltage Pulse
A
B
–
Vsns
PWR
+
C
M8PP1 SPECIFICATIONS
ES-5378 Rev.5 Page 4/5
http://www.m-system.co.jp/
MODEL: M8PP1
Specifications are subject to change without notice.
M8PP1 SPECIFICATIONS
ES-5378 Rev.5 Page 5/5
http://www.m-system.co.jp/
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明