MSEF-65-R/UL [MSYSTEM]

Plug-in Signal Conditioners M-UNIT;


型号：	MSEF-65-R/UL
厂家：	M-SYSTEM
描述：	Plug-in Signal Conditioners M-UNIT
文件：	总4页 (文件大小：133K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: MSEF

Plug-in Signal Conditioners M-UNIT

[2] POWER INPUT

AC Power

B: 100 V AC

DC ALARM

(front control button adjustment)

C: 110 V AC

D: 115 V AC

Functions & Features

F: 120 V AC

• Providing SPDT relay outputs at preset DC input levels

• Dual trip

G: 200 V AC (Option /UL not selectable.)

H: 220 V AC (Option /UL not selectable.)

J: 240 V AC (Option /UL not selectable.)

DC Power

• Latching or non-latching output

• Deadband, ON-delay, Hi/Lo trip, failsafe action can be

programmed with front UP/DOWN control buttons

• Enclosed relays

R: 24 V DC (Option /UL not selectable.)

S: 12 V DC (Option /UL not selectable.)

• High-density mounting

Typical Applications

• Annunciator

[3] OPTIONS (multiple selections)

Standards & Approvals

• Various alarm applications

blank: CE marking

/UL: UL approval, CE marking

Other Options

(1.97)

blank: none

/Q: Option other than the above (specify the specification)

(3.15)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

136

(5.35)

/C02: Polyurethane coating

mm (inch)

/C03: Rubber coating (UL not available)

TERMINAL SCREW MATERIAL

/S01: Stainless steel (UL not available)

MODEL: MSEF–[1]5–[2][3]

GENERAL SPECIFICATIONS

Construction: Plug-in

ORDERING INFORMATION

• Code number: MSEF-[1]5-[2][3]

Specify a code from below for each of [1] through [3].

(e.g. MSEF-65-F/UL/Q)

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

• Specify the specification for option code /Q

(e.g. /C01)

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Latching output: Alternatively selectable to deadband

option; reset with the power turned OFF.

Front LEDs: Red/green dual-color LED

Run mode: Red turns ON in tripped condition.

L1 for Output 1, L2 for Output 2

Check mode: Green turns ON.

Set mode: Red/green turns ON.

Display: LED, 4-digit digital meter

Display range: -14.0 to +113.5 %

Programming: Front key pad

[1] INPUT

Current

A: 4 – 20 mA DC (Input resistance 250 Ω)

B: 2 – 10 mA DC (Input resistance 500 Ω)

C: 1 – 5 mA DC (Input resistance 1000 Ω)

Voltage

4: 0 – 10 V DC (Input resistance 1 MΩ min.)

5: 0 – 5 V DC (Input resistance 1 MΩ min.)

6: 1 – 5 V DC (Input resistance 1 MΩ min.)

• Trip point

• Hysteresis (deadband)

OUTPUT

5: Dual trip; SPDT or transfer contact

• Latching

• Trip operation (Hi/Lo, coil energized/de-energized)

• ON-delay time

MSEF SPECIFICATIONS

ES-1607 Rev.9 Page 1/4

http://www.m-system.co.jp/

MODEL: MSEF

• Power ON-delay time

to power to ground)

(Refer to the instruction manual)

STANDARDS & APPROVALS

EU conformity:

INPUT SPECIFICATIONS

■ DC Current:

EMC Directive

Shunt resistor attached to the input terminals (0.5 W)

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1

OUTPUT SPECIFICATIONS

■ Relay Contact: 100 V AC @ 5 A (cos ø = 1)

120 V AC @ 5 A (cos ø = 1)

Measurement Category II (output)

Installation Category II (power)

Pollution Degree 2

240 V AC @ 2.5 A (cos ø = 1)

30 V DC @ 5 A (resistive load)

Input to output to power: Basic insulation (300 V)

RoHS Directive

Maximum switching voltage: 300 V AC or 125 V DC

Maximum switching power: 600 VA or 150 W

Minimum load: 5 V DC @ 10 mA

EN 50581

Approval:

Mechanical life: 5 × 10 cycles

UL/C-UL general safety requirements

(UL 3111-1, CAN/CSA-C22.2 No.1010-1)

Alarm Trip Operation

[Example]

Terminal No. in parentheses

Output 1: High trip, coil energized at alarm

Output 2: Low trip, coil energized at alarm

(9-10)ON

(9-11)ON

Output 1

(1-2)ON

Output 2

(1-3)ON

Input

(%)

▲

100

Lo Setpoint

Hi Setpoint

Trip Operation in Power Failure: Terminals 1 –Ê3, 9 – 11 turn on.

INSTALLATION

Power input

•AC: Operational voltage range: rating ±10 %,

50/60 ±2 Hz, approx. 3 VA

•DC: Operational voltage range: rating ±10 %,

ripple 10 %p-p max., approx. 3 W (120 mA at 24 V)

Operating temperature: -5 to +60°C (23 to 140°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 400 g (0.88 lb)

PERFORMANCE in percentage of span

Setpoint accuracy: ±0.5 %

Display accuracy: ±0.1 %

Deadband setpoint accuracy: ±0.3 %

Trip point repeatability: ±0.1 %

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: ≤ 0.5 sec. (0 – 100 % at 90 % setpoint)

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

MSEF SPECIFICATIONS

ES-1607 Rev.9 Page 2/4

http://www.m-system.co.jp/

MODEL: MSEF

EXTERNAL VIEW

L1 Monitor LED

L2 Monitor LED

Digital Display

UP Control

DOWN Control

MODE Selector

EXTERNAL DIMENSIONS unit: mm (inch)

CLAMP

(top & bottom)

7.8 (.31)

DIN RAIL

35mm wide

2–

4.5 (.18) dia.

MTG HOLE

25 (.98) deep

10 11

–M3.5

SCREW

50 (1.97)

107 (4.21)

136 (5.35)

40 (1.57)

50 (1.97)

[3.3 (.13)]

• When mounting, no extra space is needed between units.

TERMINAL ASSIGNMENTS unit: mm (inch)

INPUT RESISTOR

(model: REM)

10 11

Input shunt resistor attached

for current input.

MSEF SPECIFICATIONS

ES-1607 Rev.9 Page 3/4

http://www.m-system.co.jp/

MODEL: MSEF

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

■ Relay Protection

• AC Powered

MONITOR LED

Inductive

Load (Coil)

11 N.C.

10 N.O.

Low Drift

Amplifier

Varistor or Spark

Quenching Circuit

–

LOAD

OUTPUT 1

INPUT

COM

N.C.

Digital

Computation

Circuit

DISPLAY/SETTING

• DC Powered

Inductive

Load (Coil)

DOWN

MODE

N.O.

OUTPUT 2

POWER

Diode, Varistor or

CR Circuit

LOAD

COM

U(+)

V(–)

Base Socket

*Input shunt resistor attached for current input.

Specifications are subject to change without notice.

MSEF SPECIFICATIONS

ES-1607 Rev.9 Page 4/4

http://www.m-system.co.jp/

相关型号：