首页 |元器件品牌

R3-DAC16W/CE [MSYSTEM]

Remote I/O R3 Series DISCRETE INPUT OUTPUT MODULE;
R3-DAC16W/CE
型号： R3-DAC16W/CE
厂家： M-SYSTEM    M-SYSTEM
描述：

Remote I/O R3 Series DISCRETE INPUT OUTPUT MODULE

输入元件 输出元件
文件： 总7页 (文件大小：180K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
MODEL: R3-DAC16  
/C03: Rubber coating  
Remote I/O R3 Series  
CAUTION  
DISCRETE INPUT OUTPUT MODULE  
(Di 8 points, Do 8 points)  
• This unit is not designed to be used with the following  
types of interface modules (models: R3-NC2, R3-NEIP1, R3-  
NFx, R3-NLx).  
Typical Applications  
• Controls start/stop of field devices with ON/OFF control  
output  
• Output completion status data is compatible with interface  
modules (models: R3-NC1, R3-NC3, R3-NDx, R3-NE1, R3-  
NFL1, R3-NM1, R3-NM4, R3-NP1) of firmware version V2.00  
or higher, and interface modules (models: R3-NM3, R3-  
NML3) of firmware version V1.00 or higher.  
• Simplifies signal hold circuit of field devices  
• Utilizing One-Shot Output reduces the load of PLC side.  
27.5 [1.08]  
GENERAL SPECIFICATIONS  
Connection  
130  
[5.12]  
Internal bus: Via the Installation Base (model: R3-BSx)  
Input, Output: M3 separable screw terminal  
(torque 0.5 N·m)  
109  
[4.29]  
Internal power: Via the Installation Base (model: R3-BSx)  
Screw terminal: Nickel-plated steel  
mm [inch]  
Isolation: Input to output to internal bus or internal power  
Output mode setting: One-Shot Output Mode, ON/OFF  
Control Output Mode, Continuance Output Mode selectable  
with DIP switch  
MODEL: R3–DAC16[1][2]  
Data length Setting: 8bit, 4bit selectable with DIP switch  
(For ON/OFF Control Output Mode only)  
One-shot ON time setting: 0.1 to 25.6 sec. selectable with  
DIP switch  
ORDERING INFORMATION  
• Code number: R3-DAC16[1][2]  
Specify a code from below for each of [1] and [2].  
(e.g. R3-DAC16W/CE/Q)  
ON/OFF control output setting: Swappable its pair with DIP  
switch.  
• Specify the specification for option code /Q  
(e.g. /C01)  
Output hold setting: Setting for communication error with  
side DIP SW  
NO. OF CHANNELS  
16: 8 points input, 8 points output  
RUN indicator: Bi-color (red/green) LED;  
Red when the bus A operates normally;  
Green when the bus B operates normally;  
Amber when both buses operate normally.  
ERR indicator: Bi-color (red/ green) LED;  
Green in normal operating conditions  
Red with the abnormal configuration  
Status indicator: Red LED;  
[1] COMMUNICATION MODE  
S: Single  
W: Dual  
[2] OPTIONS (multiple selections)  
Standards & Approvals  
blank: Without CE  
1 to 8: Intput status, turns on with input ON.  
9 to 16: Output status, turns on with output ON.  
Di read rate setting: 1 / 5 / 10 / 20 / 50 / 70 / 100 / 200  
msec. selectable with DIP SW  
/CE: CE marking  
Other Options  
blank: none  
INPUT SPECIFICATIONS  
Number of input: 8 points  
/Q: Option other than the above (specify the specification)  
Isolation: Optical isolator  
SPECIFICATIONS OF OPTION: Q  
COATING (For the detail, refer to M-System's web site.)  
/C01: Silicone coating  
Input resistance: Approx. 4.4 kΩ  
Common: Positive or negative (NPN/PNP) common per 8  
points (2 terminals)  
/C02: Polyurethane coating  
Rated input voltage: 24 V DC +10/-15 % (ripple 5 %p-p  
R3-DAC16 SPECIFICATIONS  
ES-8459 Rev.7 Page 1/7  
https://www.m-system.co.jp/  
MODEL: R3-DAC16  
max.)  
• Output Hold  
ON voltage/current: ≥ 11 V, ≥ 2.5 mA  
OFF voltage/current: ≤ 6 V, ≤ 1.3 mA  
If both are in error, the module holds the signal and stands  
by until one of the communications recovers.  
• Output OFF  
If both are in error, the module outputs OFF signals and  
stands by until one of the communications recovers.  
At the startup, it outputs OFF until the communication is  
established and normal data is received.  
OUTPUT SPECIFICATIONS  
Number of output: 8 points  
Common: All 8 points (2 terminals)  
Common current: Max. 2 A (total of 2 terminals)  
Rated load:  
250 V AC @ 0.5 A (cos ø = 1)  
30 V DC @ 0.5 A (resistive load)  
(Less than 50 V AC to conform with EU Directive)  
Maximum switching voltage: 250 V AC or 30 V DC  
Maximum switching power: 250 VA or 30 W  
Minimum load: 1 V DC @ 1 mA  
Mechanical life: 2 × 10 cycles (300 cycles/min.)  
7
When driving an inductive load, external contact protection  
and noise quenching recommended.  
INSTALLATION  
Operating temperature: -10 to +55°C (14 to 131°F)  
Operating humidity: 30 to 90 %RH (non-condensing)  
Atmosphere: No corrosive gas or heavy dust  
Mounting: Installation Base (model: R3-BSx)  
Weight: 200 g (0.44 lb)  
PERFORMANCE  
Output ON time accuracy: ±10 % max. for 1 sec. or less  
setting; ±0.1 sec. max. for 1 sec. or more setting  
Data allocation: 1  
Current consumption: 130 mA  
Insulation resistance: ≥ 100 MΩ with 500 V DC  
Dielectric strength: 1500 V AC @ 1 minute (input to output  
to internal bus or internal power)  
2000 V AC @ 1 minute (power input to FG; isolated on the  
power supply module)  
STANDARDS & APPROVALS  
EU conformity:  
EMC Directive  
EMI EN 61000-6-4  
EMS EN 61000-6-2  
RoHS Directive  
FUNCTIONS  
■OUTPUT HOLD or OUTPUT OFF  
In normal conditions, the module outputs the signal from  
the preferred bus A.  
When an error is detected, the output is switched to the  
data from the bus B.  
R3-DAC16 SPECIFICATIONS  
ES-8459 Rev.7 Page 2/7  
https://www.m-system.co.jp/  
MODEL: R3-DAC16  
EXTERNAL VIEW  
■ FRONT VIEW  
■ SIDE VIEW  
ERR LED  
RUN LED  
Functions  
SW1  
SW2  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
ON/OFF Control  
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
I/O Status Indicator LED  
Output  
One-Shot  
ON Time  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
Di Read Rate  
ON  
ON  
Functions  
SW3  
ON  
Data Length  
Output Mode  
Output Hold  
4
3
2
1
I/O DATA DESCRIPTIONS  
■ ONE-SHOT OUTPUT MODE  
8-bit output data (Do 1 through 8) and output (Ch1 through 8) are assigned 1:1.  
Do  
WRITE  
ONE-SHOT OUTPUT/RESET  
Ch1 Output  
Di  
OUTPUT COMPLETION STATUS  
Ch1 Output Completion Status  
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
Di 9  
Do 1  
Ch1 Output Completion Reset  
Ch2 Output  
Di 10  
Di 11  
Di 12  
Di 13  
Di 14  
Di 15  
Di 16  
Ch2 Output Completion Status  
Ch3 Output Completion Status  
Ch4 Output Completion Status  
Ch5 Output Completion Status  
Ch6 Output Completion Status  
Ch7 Output Completion Status  
Ch8 Output Completion Status  
Do 2  
Do 3  
Do 4  
Do 5  
Do 6  
Do 7  
Do 8  
Ch2 Output Completion Reset  
Ch3 Output  
Ch3 Output Completion Reset  
Ch4 Output  
Ch4 Output Completion Reset  
Ch5 Output  
Ch5 Output Completion Reset  
Ch6 Output  
Ch6 Output Completion Reset  
Ch7 Output  
Ch7 Output Completion Reset  
Ch8 Output  
Ch8 Output Completion Reset  
R3-DAC16 SPECIFICATIONS  
ES-8459 Rev.7 Page 3/7  
https://www.m-system.co.jp/  
MODEL: R3-DAC16  
■ ON/OFF CONTROL OUTPUT MODE  
• Data Length: 8 bits  
Do 1 through 8 are assigned to Ch1 through 8.  
Do  
WRITE  
ONE-SHOT OUTPUT/RESET  
Not Operating  
Di  
OUTPUT COMPLETION STATUS  
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
Ch1 Output  
Di 9  
Ch1 Output Completion Status  
Ch2 Output Completion Status  
Do 1 Do 2  
Ch2 Output  
Di 10  
Output Data Reset  
Not Operating  
Ch3 Output  
Di 11  
Di 12  
Ch3 Output Completion Status  
Ch4 Output Completion Status  
Do 3 Do 4  
Do 5 Do 6  
Do 7 Do 8  
Ch4 Output  
Output Data Reset  
Not Operating  
Ch5 Output  
Di 13  
Di 14  
Ch5 Output Completion Status  
Ch6 Output Completion Status  
Ch6 Output  
Output Data Reset  
Not Operating  
Ch7 Output  
Di 15  
Di 16  
Ch7 Output Completion Status  
Ch8 Output Completion Status  
Ch8 Output  
Output Data Reset  
The above table shows the case of Not Swapped (SW2-8: OFF). ON/OFF control output is swapped with its pair when SW2-8 is  
ON. The following is an example of Do 1 and Do 2.  
Do  
WRITE  
ONE-SHOT OUTPUT/RESET  
Not Operating  
Di  
OUTPUT COMPLETION STATUS  
0
1
0
1
0
0
1
1
Ch2 Output  
Di 10  
Di 9  
Ch2 Output Completion Status  
Ch1 Output Completion Status  
Do 1 Do 2  
Ch1 Output  
Output Data Reset  
• Data Length: 4 bits  
Do 1 through 4 are assigned to Ch1 through 8 as 1:2.  
Do  
WRITE  
0
ONE-SHOT OUTPUT/RESET  
Ch1 Output  
Di  
OUTPUT COMPLETION STATUS  
Ch1 Output Completion Status  
Di 9  
Do 1  
1
Ch2 Output  
Di 10  
Ch2 Output Completion Status  
0
1
0
1
0
1
Ch3 Output  
Ch4 Output  
Ch5 Output  
Ch6 Output  
Ch7 Output  
Ch8 Output  
Di 11  
Di 12  
Di 13  
Di 14  
Di 15  
Di 16  
Ch3 Output Completion Status  
Ch4 Output Completion Status  
Ch5 Output Completion Status  
Ch6 Output Completion Status  
Ch7 Output Completion Status  
Ch8 Output Completion Status  
Do 2  
Do 3  
Do 4  
The above table shows the case of Not Swapped (SW2-8: OFF). ON/OFF control output is swapped with its pair when SW2-8 is  
ON. The following is an example of Do 1.  
Do  
WRITE  
0
ONE-SHOT OUTPUT/RESET  
Ch2 Output  
Ch1 Output  
Di  
OUTPUT COMPLETION STATUS  
Ch2 Output Completion Status  
Di 10  
Do 1  
1
Di 9  
Ch1 Output Completion Status  
R3-DAC16 SPECIFICATIONS  
ES-8459 Rev.7 Page 4/7  
https://www.m-system.co.jp/  
MODEL: R3-DAC16  
■ CONTINUOUS OUTPUT MODE  
Do 1 through 8 are assigned to and Ch1 through 8. When data Do is “1” output is ON (energized) and when it is “0” output is OFF  
(de-energized). The operation is equivalent to 16 points discrete output module (model: R3-DC16). Output completion status Di  
is related to Do.  
Do  
CONTINUOUS OUTPUT  
Ch1 Output  
Di  
OUTPUT COMPLETION STATUS  
Ch1 Output Completion Status  
Do 1  
Di 9  
Do 2  
Ch2 Output  
Di 10  
Ch2 Output Completion Status  
Do 3  
Do 4  
Do 5  
Do 6  
Do 7  
Do 8  
Ch3 Output  
Ch4 Output  
Ch5 Output  
Ch6 Output  
Ch7 Output  
Ch8 Output  
Di 11  
Di 12  
Di 13  
Di 14  
Di 15  
Di 16  
Ch3 Output Completion Status  
Ch4 Output Completion Status  
Ch5 Output Completion Status  
Ch6 Output Completion Status  
Ch7 Output Completion Status  
Ch8 Output Completion Status  
DATA ASSIGNMENT  
■ Do  
15  
0
Do 1  
Do 2  
Do 3  
Do 8  
Note 1: For 4-bit length ON/OFF control mode, Do 5 through Do 8 are unavailable.  
Note 2: For the combination with Modbus communication module (model: R3-NE1, R3-NM1 and such),  
use the addresses of Coil (0X) for Modbus I/O assignment.  
■ Di  
15  
0
Di 1  
Di 2  
Di 3  
Di 16  
Note 1: Di 9 – 16 data is not practical discrete input data. It is “output completion status” internal data.  
Note 2: For the combination with Modbus communication module (model: R3-NE1, R3-NM1 and such),  
use the addresses of Input (1X) for Modbus I/O assignment.  
R3-DAC16 SPECIFICATIONS  
ES-8459 Rev.7 Page 5/7  
https://www.m-system.co.jp/  
MODEL: R3-DAC16  
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]  
27.5 [1.08]  
109 [4.29]  
POSITIONING  
GUIDE  
1
11  
2
20–M3  
SCREW  
12  
3
13  
4
14  
5
15  
6
16  
7
17  
8
18  
9
19  
10  
20  
TERMINAL  
COVER  
R3-DAC16 SPECIFICATIONS  
ES-8459 Rev.7 Page 6/7  
https://www.m-system.co.jp/  
MODEL: R3-DAC16  
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM  
STATUS  
ERR INDICATOR  
RUN  
LED  
DIP SW  
LED  
LED  
INTERNAL BUS A  
Communication  
Circuit  
Input Circuit  
1
2
3
4
5
6
7
8
INTERNAL BUS B  
*
1
2
Di 1  
Di 2  
INTERNAL POWER  
3
Di 3  
9
4
Di 4  
6
7
Do 1  
Do 2  
Do 3  
Do 4  
Do 5  
Do 6  
Do 7  
Do 8  
10  
11  
12  
13  
14  
15  
16  
11  
12  
13  
14  
5
Di 5  
Di 6  
Control  
Circuit  
8
Di 7  
9
Di 8  
16  
17  
18  
19  
10  
20  
COM1  
COM1  
15  
COM2  
COM2  
Output Circuit  
Numbers in italic indicate LED No.s assigned to the front panel LEDs.  
*For dual redundant communication.  
■ Input Circuit  
■ Output Circuit  
1
Di 1  
1
Ry  
9
6
Do 1  
8
Control  
Circuit  
Control  
Circuit  
Di 8 14  
Ry  
16  
19 Do 8  
5
10  
20  
15  
Specifications are subject to change without notice.  
R3-DAC16 SPECIFICATIONS  
ES-8459 Rev.7 Page 7/7  
https://www.m-system.co.jp/  

相关型号：

SI9130DB

 5- and 3.3-V Step-Down Synchronous Converters

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1-E3

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135_11

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9136_11

 Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130CG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130LG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130_11

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137DB

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137LG

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9122E

 500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification Drivers

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明