R3-NE1-L3/Q [MSYSTEM]

Remote I/O R3 Series ETHERNET INTERFACE MODULE;


型号：	R3-NE1-L3/Q
厂家：	M-SYSTEM
描述：	Remote I/O R3 Series ETHERNET INTERFACE MODULE 以太网：16GBASE-T
文件：	总8页 (文件大小：227K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: R3-NE1

Remote I/O R3 Series

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

ETHERNET INTERFACE MODULE

(Modbus/TCP)

/C02: Polyurethane coating

/C03: Rubber coating

EX-FACTORY SETTING

27.5 [1.08]

/SET: Preset according to the Ordering Information Sheet

(No. ESU-8361)

130

[5.12]

RELATED PRODUCTS

• PC configurator software (model: R3CON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

109

[4.29]

mm [inch]

MODEL: R3-NE1-[1][2]

GENERAL SPECIFICATIONS

Connection

ORDERING INFORMATION

• Code number: R3-NE1-[1][2]

Specify a code from below for each of [1] and [2].

(e.g. R3-NE1-R/CE/Q)

Ethernet: RJ-45 connector

Internal bus: Via the Installation Base (model: R3-BSx)

Internal power: Via the Installation Base (model: R3-BSx)

Power input, RUN contact output: M3 separable screw

terminal (torque 0.5 N·m)

• Specify the specification for option code /Q

(e.g. /C01/SET)

Screw terminal: Nickel-plated steel

Isolation: Ethernet to internal bus or internal power to power

supply to RUN contact output to FG

[1] POWER INPUT

N: No power supply

Input error data setting: Input value setting at input module

error with side DIP SW

(Use with Ver.2.00 or higher versions of Power Supply Module

(model: R3-PSx) to conform with CE marking.)

AC Power

Dual communication setting: Set with the side DIP switch

Data allocation setting: Set with the side DIP switch

RUN indicator: Bi-color (green/red) LED; Green ON in normal

communication; Red ON when receiving data (Function

selected with DIP SW)

K3: 100 – 120 V AC

(Operational voltage range 85 - 132 V, 47 - 66 Hz) *

(CE not available)

L3: 200 – 240 V AC

ERR indicator: Bi-color (green/red) LED;

Green ON or blinking at communication error; Red ON at

transmitting data (Function selected with DIP SW)

■ RUN CONTACT OUTPUT

(Operational voltage range 170 - 264 V, 47 - 66 Hz) *

(CE not available)

DC Power

R: 24 V DC

RUN contact: Turns ON while the green RUN LED is ON

(Ethernet in normal communication).

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) *

* Not selectable for use with independent power modules or

network modules with the internal power input options.

Rated load: 250 V AC @ 0.5 A (cos ø = 1)

30 V DC @ 0.5 A (resistive load)

(Less than 50 V AC to conform with EU Directive)

Maximum switching voltage: 250 V AC or 30 V DC

Maximum switching power: 250 VA or 150 W

Minimum load: 1 V DC @ 1 mA

[2] OPTIONS (multiple selections)

Standards & Approvals

blank: Without CE

/CE: CE marking

Mechanical life: 2 × 10 cycles (300 cycles/min.)

Other Options

When driving an inductive load, external contact protection

and noise quenching recommended.

blank: none

/Q: Option other than the above (specify the specification)

R3-NE1 SPECIFICATIONS

ES-8361 Rev.24 Page 1/8

https://www.m-system.co.jp/

MODEL: R3-NE1

ETHERNET COMMUNICATION

Communication Standard: IEEE 802.3u

Transmission: 10BASE-T, 100BASE-TX

Baud rate: 10/100 Mbps (Auto Negotiation function)

Protocol: Modbus/TCP

Data: RTU (Binary)

Max. number of socket connections: 2

Transmission media: 10BASE-T (STP, Category 5) 100BASE-

TX (STP, Category 5e)

Max. length of fieldbus segment: 100 meters

Ethernet indicator LED: LINK, DPLX, LINK10, LINK100, COL

IP address: 192.168.0.1 (factory setting);

Selectable with PC Configurator Software (model: R3CON)

Port No.: 502

INSTALLATION

Power consumption

•AC: Approx. 20 VA

•DC: Approx. 12 W

Current consumption (no power supply): 100 mA

Output current (power supply): 250 mA continuous at 20 V

DC; 400 mA for 10 minutes

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Installation Base (model: R3-BSx)

Weight: 200 g (0.44 lb)

PERFORMANCE

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @ 1 minute (Ethernet to

internal bus or internal power to power input to RUN contact

output to FG)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

RoHS Directive

R3-NE1 SPECIFICATIONS

ES-8361 Rev.24 Page 2/8

https://www.m-system.co.jp/

MODEL: R3-NE1

EXTERNAL VIEW

■ FRONT VIEW

■ SIDE VIEW

Not used

RUN LED

ERR LED

DIP SW

SW3

SW2

SW1

Configuration

Jack

LINK

RJ-45 Modular

Jack

DPLX (Duplex)

LINK10 (10Mbps)

LINK100

(100Mbps)

COL (Collision)

MODBUS FUNCTION CODES & SUPPORTED CODES

■ Data & Control Functions

CODE NAME

Read Coil Status

Digital output from the slave (read/write)

Read Input Status

Read Holding Registers

Read Input Registers

Force Single Coil

Status of digital inputs to the slave (read only)

General purpose register within the slave (read/write)

Collected data from the eld by the slave (read only)

Digital output from the slave (read/write)

Preset Single Register

Read Exception Status

Diagnostics

General purpose register within the slave (read/write)

Program 484

Poll 484

Fetch Comm. Event Counter

Fetch Comm. Event Log

Program Controller

Poll Controller

Fetch a status word and an event counter

A status word, an event counter, a message count and a eld of event bytes

Force Multiple Coils

Preset Multiple Registers

Report Slave ID

Digital output from the slave (read/write)

General purpose register within the slave (read/write)

Slave type / ‘RUN’ status

Program 884/M84

Reset Comm. Link

Read General Reference

Write General Reference

Mask Write 4X Register

Read/Write 4X Register

Read FIFO Queue

R3-NE1 SPECIFICATIONS

ES-8361 Rev.24 Page 3/8

https://www.m-system.co.jp/

MODEL: R3-NE1

■ Exception Codes

CODE NAME

Illegal Function

Function code is not allowable for the slave

Address is not available within the slave

Data is not valid for the function

Illegal Data Address

Illegal Data Value

Slave Device Failure

Acknowledge

Slave Device Busy

Negative Acknowledge

Memory Parity Error

■ Diagnostic Subfunctions

CODE NAME

Return Query Data

Loop back test

Restart Comm. Option

Return Diagnostic Register

Change ASCII Input Delimiter

Force Listen Only Mode

Reset the slave and clear all counters

Contents of the diagnostic data (2 bytes)

Delimiter character of ASCII message

Force the slave into Listen Only Mode

MODBUS I/O ASSIGNMENT

ADDRESS

DATA TYPE

DATA

Digital Output (discrete output)

Coil (0X)

1 – 1024

Digital Input (discrete input)

Module Status

Error Status

1025 – 1040

1041 – 1056

1057 – 1072

1 – 256

Inputs (1X)

Data Error Status

Analog Input

Input Registers (3X)

257 – 768

1 – 256

Analog Input

Analog Output

Holding Registers (4X)

257 – 768

I: Integer, 0 – 10000 (0 – 100%)

F: Floating (32-bit data cannot be accessed using !oating addresses.)

Note: DO NOT access addresses other than mentioned above. Such access may cause problems such as inadequate operation.

• Module Status indicates whether individual I/O modules are mounted or not. The bit corresponding to the mounted slot turns to

“1,” and the unmounted slot to “0.”

• Error Status indicates error status for each module as described below. The bit corresponding to such module turns to “1.”

R3-TSx, R3-RSx, R3-US4: Input burnout

R3-DA16A:

R3-YSx:

R3-PC16A:

Power input in error or disconnected

Output current error (e.g. load unconnected)

External power supply in error or disconnected

• Data Error Status indicates overrange (R3-US4: out of -10% to +110%; the other types: out of -15% to +115%) status for each

module. The bit corresponding to such module turns to “1.”

R3-NE1 SPECIFICATIONS

ES-8361 Rev.24 Page 4/8

https://www.m-system.co.jp/

MODEL: R3-NE1

TRANSMISSION DATA DESCRIPTIONS

The DIP SW located at the side of the module species each I/O module’s data allocation (occupied data area).

For example, when the data areas are assigned as shown below:

Module 1

Module 2

Module 3

Module 4

Module 5

Module 6

Module 7

Then the I/O data are assigned as in the table below:

ADDRESS POSITION

1 – 4,

ADDRESS

1 – 64

POSITION

Slot 1

Input Registers (3X)

257 – 264

265 – 272

273 – 280

281 – 282

283 – 284

285 – 286

287 – 288

Slot 1

Slot 2

Slot 3

Slot 4

Slot 5

Slot 6

Slot 7

Coil (0X)

Holding Registers (4X)

Inputs (1X)

5 – 8,

9 – 12,

13,

65 – 128

129 – 192

193 – 208

209 – 224

225 – 240

241 – 256

Slot 2

Slot 3

Slot 4

14,

Slot 5

15,

Slot 6

16,

Slot 7

For Coil (0X) and Inputs (1X), addresses 16 times assigned data

areas (Data Allocation Type) are allotted with the Data Allocation

Type ‘1’ and ‘4.’ With ‘8’ and ‘16,’ 64 (4 × 16) are automatically al-

lotted.

MODULE STATUS, ERROR STATUS, DATA ERROR STATUS

Shows each module's availability and error status.

Module 1

Module 2

Module 3

Module 16

I/O DATA DESCRIPTIONS

The data allocations for typical I/O modules are shown below.

Refer to the manual for each module for detailed data allocations.

■ ANALOG DATA (16-bit data, models: R3-SV4, YV4, DS4, YS4, US4, etc.)

16-bit binary data.

Basically, 0 to 100% of the selected I/O range is converted into 0 to 10000 (binary).

-15 to 0 % is a negative range represented in 2’s complement.

In case of R3-US4, -10 to 0% is a negative range represented in 2's complement.

R3-NE1 SPECIFICATIONS

ES-8361 Rev.24 Page 5/8

https://www.m-system.co.jp/

MODEL: R3-NE1

■ TEMPERATURE DATA (16-bit data, models: R3-RS4, TS4, US4, etc.)

16-bit binary data.

With °C temperature unit, raw data is multiplied by 10. For example, 25.5°C is converted into 255.

With °F temperature unit, the integer section of raw data is directly converted into the data.

For example, 135.4°F is converted into 135.

Minus temperature is converted into negative values, represented in 2’s complements.

■ ANALOG DATA (16-bit data, models: R3-CT4A, CT4B, etc.)

16-bit binary data.

Integer obtained by multiplying unit value (A) by 100.

In case of CLSE-R5, integer obtained by multiplying unit value (A) by 1000.

■ ACCUMULATED COUNT DATA (32-bit data, models: R3-PA2, PA4A, WT1, WT4, etc.)

32-bit binary data is used for accumulated counts and encoder positions.

Lower 16 bits are allocated from the lowest address to higher ones, higher 16 bits in turn.

32-bit data cannot be accessed using oating addresses.

Lower 16 bits

Higher 16 bits

■ BCD DATA (32-bit data, models: R3-BA32A, BC32A, etc.)

32-bit binary data is used for BCD.

Lower 16 bits are allocated from the lowest address to higher ones, higher 16 bits in turn.

32-bit data cannot be accessed using oating addresses.

Lower 16 bits

Higher 16 bits

■ 16-POINT DISCRETE DATA (models: R3-DA16, DC16, etc.)

Input 1 (Output 1)

Input 2 (Output 2)

Input 3 (Output 3)

Input 16 (Output 16)

0 : OFF

1 : ON

R3-NE1 SPECIFICATIONS

ES-8361 Rev.24 Page 6/8

https://www.m-system.co.jp/

MODEL: R3-NE1

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]

27.5 [1.08]

109 [4.29]

POSITIONING

GUIDE

6–M3

SCREW

TERMINAL

COVER

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Note: In order to improve EMC performance, bond the FG terminal to ground.

Caution: FG terminal is NOT a protective conductor terminal.

LED

Isolation

Control

Circuit

Communication

Circuit

RJ-45 MODULAR JACK

Modbus/TCP

INTERNAL BUS

RUN +

ETHERNET DIP SW

LED

RUN CONTACT OUTPUT

RUN –

INTERNAL POWER

U (+) 2

POWER INPUT

V (–)

JACK

CONFIGURATION JACK

*Not provided with ‘No Power Supply’ type module.

SYSTEM CONFIGURATION EXAMPLES

STP Cable

Switch / Hub

STP Cable

(10BASE-T, 100BASE-TX)

Ethernet Interface Module

(model: R3-NE1)

Ethernet Interface Module

(model: R3-NE1)

R3-NE1 SPECIFICATIONS

ES-8361 Rev.24 Page 7/8

https://www.m-system.co.jp/

MODEL: R3-NE1

Specifications are subject to change without notice.

R3-NE1 SPECIFICATIONS

ES-8361 Rev.24 Page 8/8

https://www.m-system.co.jp/

R3-NE1-L3/Q [MSYSTEM]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E