R3-NF2-K3 [MSYSTEM]

Remote I/O R3 Series T-Link INTERFACE MODULE;


型号：	R3-NF2-K3
厂家：	M-SYSTEM
描述：	Remote I/O R3 Series T-Link INTERFACE MODULE
文件：	总5页 (文件大小：156K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: R3-NF2

Remote I/O R3 Series

GENERAL SPECIFICATIONS

Connection

T-Link: Euro type connector terminal (applicable wire size:

T-Link INTERFACE MODULE

(Fuji Electric T-Link interface module equivalent)

0.2 to 2.5 mm , stripped length 7 mm)

Internal bus: Via the Installation Base

27.5 (1.08)

(model: R3-BSx)

Internal power: Via the Installation Base (model: R3-BSx)

Power input, RUN contact output: M3 separable screw

terminal (torque 0.5 N·m)

130

(5.12)

Screw terminal: Nickel-plated steel

Isolation: T-Link to internal bus or internal power to power

input to RUN contact output to FG

119

(4.69)

mm (inch)

Input error data setting: Input value setting at input module

error with side DIP SW

Dual communication setting: Set with the side DIP switch

RUN indicator: Bi-color (green/red) LED; Green ON in normal

communication; Red blinks when receiving data (Function

selected with DIP SW)

MODEL: R3–NF2–[1][2]

ERR indicator: Bi-color (green/red) LED; Green ON in

communication errors or minor failure, blinks at errors in the

internal circuits; Red blinks when transmitting data

(Function selected with DIP SW)

ORDERING INFORMATION

• Code number: R3-NF2-[1][2]

Specify a code from below for each of [1] and [2].

(e.g. R3-NF2-R/Q)

■ RUN CONTACT OUTPUT

• Specify the specification for option code /Q

(e.g. /C01/SET)

Rated load: 250 V AC @ 0.5 A (cos ø = 1)

30 V DC @ 0.5 A (resistive load)

Maximum switching voltage: 250 V AC or 30 V DC

Maximum switching power: 250 VA or 150 W

Minimum load: 1 V DC @ 1 mA

[1] POWER INPUT

N: No power supply

Mechanical life: 2 × 10 cycles (rate 300 cycles/min.) When

AC Power

driving an inductive load, external contact protection and

noise quenching recommended.

K3: 100 – 120 V AC

(Operational voltage range 85 - 132 V, 47 - 66 Hz) *

L3: 200 – 240 V AC

(Operational voltage range 170 - 264 V, 47 - 66 Hz) *

DC Power

T-Link SPECIFICATIONS

Configuration: Multi-drop

R: 24 V DC

Communication: Half-duplex

Baud rate: 500 kbps

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) *

* Not selectable for use with independent power modules or

network modules with the internal power input options.

Max. transmission data capacity: 117 words for input, 125

words for output

Node address: Rotary switch; 00 – 99

Transmission media/distance:

[2] OPTIONS

blank: none

KPEV-SB, 0.75 mm

× 1 pair, 700 m

× 1 pair, 1000 m

T-KPEV-SB, 1.25 mm

/Q: With options (specify the specification)

INSTALLATION

Power consumption

•AC: Approx. 20 VA

•DC: Approx. 12 W

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

Current consumption (no power supply): 120 mA

Output current (power supply): 230 mA continuous at 20 V

DC; 380 mA for 10 minutes

/C03: Rubber coating

EX-FACTORY SETTING

/SET: Preset according to the Ordering Information Sheet

(No. ESU-8438)

Operating temperature: -10 to +55°C (14 to 131°F)

R3-NF2 SPECIFICATIONS

ES-8438 Rev.4 Page 1/5

http://www.m-system.co.jp/

MODEL: R3-NF2

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Installation Base (model: R3-BSx)

Weight: 200 g (0.44 lb)

PERFORMANCE

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @ 1 minute (T-Link to

internal bus or internal power to power input to RUN contact

output to FG)

EXTERNAL VIEW

n FRONT VIEW

n SIDE VIEW

Node Address Setting

Rotary SW (MSB)

SA1

SA2

RUN LED

Node Address Setting

Rotary SW (LSB)

ERR LED

Functions

SW3

RT+

RT–

Configuration Jack

Euro Type

Connector Terminal

TRANSMISSION DATA DESCRIPTIONS

This module allocates T-link addresses in order from slot 1. Set the begin address to the module’s node address (T-Link address.)

For example; if the formation of the I/O modules is: slot 1: R3-SV4, slot 2: R3-YV4, slot 3: R3-DA16 and slot 4: R3-DC16, the I/O

data is assigned as detailed on the table below. Set “10” to the module address. Discrete I/O data can be also represented with

bit address. Ch.1 through 16 are assigned to 0 thr. F.

SLOT

MODULE

R3-SV4

ADDRESS

WORD ADDRESS CONTENTS

CH1 input data

CH2 input data

CH3 input data

CH4 input data

CH1 output data

CH2 output data

CH3 output data

CH4 output data

Input data

R3-YV4

R3-DA16

R3-DC16

Output data

R3-NF2 SPECIFICATIONS

ES-8438 Rev.4 Page 2/5

http://www.m-system.co.jp/

MODEL: R3-NF2

I/O DATA DESCRIPTIONS

The data allocations for typical I/O modules are shown below.

Refer to the manual for each module for detailed data allocations.

■ ANALOG DATA (16-bit data, models: R3-SV4, YV4, DS4, YS4, US4, etc.)

16-bit binary data.

Basically, 0 to 100% of the selected I/O range is converted into 0 to 10000 (binary).

-15 to 0 % is a negative range represented in 2’s complement.

In case of R3-US4, -10 to 0% is a negative range represented in 2's complement.

■ TEMPERATURE DATA (16-bit data, models: R3-RS4, TS4, US4, etc.)

16-bit binary data.

With °C temperature unit, raw data is multiplied by 10. For example, 25.5°C is converted into 255.

With °F temperature unit, the integer section of raw data is directly converted into the data.

For example, 135.4°F is converted into 135.

Minus temperature is converted into negative values, represented in 2’s complements.

■ ANALOG DATA (16-bit data, models: R3-CT4A, CT4B, etc.)

16-bit binary data.

Integer obtained by multiplying unit value (A) by 100.

In case of CLSE-R5, integer obtained by multiplying unit value (A) by 1000.

■ ACCUMULATED COUNT DATA (32-bit data, models: R3-PA2, PA4A, WT1, WT4, etc.)

32-bit binary data is used for accumulated counts and encoder positions.

Lower 16 bits are allocated from the lowest address to higher ones, higher 16 bits in turn.

Lower 16 bits

Higher 16 bits

■ BCD DATA (32-bit data, models: R3-BA32A, BC32A, etc.)

32-bit binary data is used for BCD.

Lower 16 bits are allocated from the lowest address to higher ones, higher 16 bits in turn.

Lower 16 bits

Higher 16 bits

R3-NF2 SPECIFICATIONS

ES-8438 Rev.4 Page 3/5

http://www.m-system.co.jp/

MODEL: R3-NF2

■ 16-POINT DISCRETE DATA (models: R3-DA16, DC16, etc.)

Input 1 (Output 1)

Input 2 (Output 2)

Input 3 (Output 3)

Input 16 (Output 16)

0 : OFF

1 : ON

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

10 (.39)

27.5 (1.08)

109 (4.29)

POSITIONING

GUIDE

6–M3

SCREW

TERMINAL

COVER

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

LED Rotary SW

Isolation

RT+

RT–

Control

Circuit

Communication

Circuit

Close to terminate.*

INTERNAL BUS

Shielded Twisted-pair

Cable

To Other

T-Link

Devices

Term. Resist.

DIP SW

–

INTERNAL POWER

RUN +

RUN –

U (+)

RUN CONTACT OUTPUT

POWER INPUT

V (–)

JACK

CONFIGURATION JACK

* When the module is at an end of the transmission line via twisted-pair calbe

(= when there is no cross wiring), close across the RT+ and RT– terminals with the

jumper included in the product package. Remove the jumper for all other locations.

**Not provided with ‘No Power Supply’ type module.

Caution: FG terminal is NOT a protective conductor terminal.

R3-NF2 SPECIFICATIONS

ES-8438 Rev.4 Page 4/5

http://www.m-system.co.jp/

MODEL: R3-NF2

Specifications are subject to change without notice.

R3-NF2 SPECIFICATIONS

ES-8438 Rev.4 Page 5/5

http://www.m-system.co.jp/

相关型号：