R3-NP1 [MSYSTEM]

Remote I/O R3 Series PROFIBUS-DP INTERFACE MODULE;


型号：	R3-NP1
厂家：	M-SYSTEM
描述：	Remote I/O R3 Series PROFIBUS-DP INTERFACE MODULE
文件：	总5页 (文件大小：164K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: R3-NP1

Remote I/O R3 Series

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

PROFIBUS-DP INTERFACE MODULE

/C02: Polyurethane coating

27.5 [1.08]

/C03: Rubber coating

CAUTION

■ Mounting on 2-slot base

130

[5.12]

Use a dedicated base (R3-BS02P) for R3-NP1.

115.1

[4.53]

GENERAL SPECIFICATIONS

Connection

mm [inch]

PROFIBUS: 9-pin D-sub connector, female

Internal bus: Via the Installation Base (model: R3-BSx)

Internal power: Via the Installation Base (model: R3-BSx)

Power input, RUN contact output: M3 separable screw

terminal (torque 0.5 N·m)

MODEL: R3-NP1-[1][2]

ORDERING INFORMATION

• Code number: R3-NP1-[1][2]

Specify a code from below for each of [1] and [2].

(e.g. R3-NP1-R/CE/Q)

Screw terminal: Nickel-plated steel

Isolation: PROFIBUS to internal bus or internal power to

power supply to RUN contact output to FG

Input error data setting: Input value setting at input module

error with side DIP SW

• Specify the specification for option code /Q

(e.g. /C01)

Dual communication setting: Set with the side DIP switch

RUN indicator: Bi-color (green/Amber) LED

(Function selected with DIP SW)

[1] POWER INPUT

N: No power supply

ERR indicator: Bi-color (green/red) LED

(Function selected with DIP SW)

AC Power

■ RUN CONTACT OUTPUT

K3: 100 – 120 V AC

RUN contact: Turns ON while the green RUN LED is ON.

(PROFIBUS in normal communication)

Rated load: 250 V AC @ 0.5 A (cos ø = 1)

30 V DC @ 0.5 A (resistive load)

(Operational voltage range 85 - 132 V, 47 - 66 Hz) *

(CE not available)

L3: 200 – 240 V AC

(Operational voltage range 170 - 264 V, 47 - 66 Hz) *

(CE not available)

(Less than 50 V AC to conform with EU Directive)

Maximum switching voltage: 250 V AC or 30 V DC

Maximum switching power: 250 VA or 150 W

Minimum load: 1 V DC @ 1 mA

DC Power

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) *

* Not selectable for use with independent power modules or

network modules with the internal power input options.

Mechanical life: 2 × 10 cycles (300 cycles/min.)

When driving an inductive load, external contact protection

and noise quenching recommended.

[2] OPTIONS (multiple selections)

Standards & Approvals

blank: Without CE

PROFIBUS COMMUNICATION

Interface: PROFIBUS-DP, slave (RS-485 isolation)

Max. baud rate: 12 Mbps

/CE: CE marking

Protocol: DPV1

Other Options

Station No. setting: Rotary switch; 00 - 7D

(Address is 7D even setting greater value)

GSD file: Msys093F.GSD

blank: none

/Q: Option other than the above (specify the specification)

GSD files are downloadable at M-System’s web site or at

PROFIBUS International site (www.profibus.com).

Input data: Max. 240 bytes

Output data: Max. 240 bytes

R3-NP1 SPECIFICATIONS

ES-8418 Rev.15 Page 1/5

https://www.m-system.co.jp/

MODEL: R3-NP1

Total I/O data: Max. 480 bytes

Diagnostics: Module-related, Status (devicerelated),

Channel-related (max. 32 channels, maskable)

Acyclic communication (MSAC2): 2 channels

INSTALLATION

Power consumption

•AC: Approx. 20 VA

•DC: Approx. 12 W

Current consumption (no power supply): 130 mA

Output current (power supply): 220 mA continuous at 20 V

DC; 370 mA for 10 minutes

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Installation Base (model: R3-BSx)

Weight: 200 g (0.44 lb)

PERFORMANCE

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @ 1 minute (PROFIBUS to

internal bus or internal power to power input to RUN output

to FG)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

RoHS Directive

R3-NP1 SPECIFICATIONS

ES-8418 Rev.15 Page 2/5

https://www.m-system.co.jp/

MODEL: R3-NP1

EXTERNAL VIEW

■ FRONT VIEW

■ SIDE VIEW

Station Address Setting

Rotary SW, upper digit

SA1

SA2

RUN LED

ERR LED

Station Address Setting

Rotary SW, lower digit

DIP SW

SW3

Configuration Jack

Network Connector

■ PROFIBUS INTERFACE

PIN No.

SIGNAL

SIGNIFICANCE

Not used

Network, B-line

RTS signal

B_line

RTS

GND

P5V

Not used

Network, A-line

Not used

A_line

I/O DATA DESCRIPTIONS

The data allocations for typical I/O modules are shown below.

Refer to the manual for each module for detailed data allocations.

■ ANALOG DATA (16-bit data, models: R3-SV4, YV4, DS4, YS4, US4, etc.)

16-bit binary data.

Basically, 0 to 100% of the selected I/O range is converted into 0 to 10000 (binary).

-15 to 0 % is a negative range represented in 2’s complement.

In case of R3-US4, -10 to 0% is a negative range represented in 2's complement.

■ TEMPERATURE DATA (16-bit data, models: R3-RS4, TS4, US4, etc.)

16-bit binary data.

With °C temperature unit, raw data is multiplied by 10. For example, 25.5°C is converted into 255.

With °F temperature unit, the integer section of raw data is directly converted into the data.

For example, 135.4°F is converted into 135.

Minus temperature is converted into negative values, represented in 2’s complements.

R3-NP1 SPECIFICATIONS

ES-8418 Rev.15 Page 3/5

https://www.m-system.co.jp/

MODEL: R3-NP1

■ ANALOG DATA (16-bit data, models: R3-CT4A, CT4B, etc.)

16-bit binary data.

Integer obtained by multiplying unit value (A) by 100.

In case of CLSE-R5, integer obtained by multiplying unit value (A) by 1000.

■ ACCUMULATED COUNT DATA (32-bit data, models: R3-PA2, PA4A, WT1, WT4, etc.)

32-bit binary data is used for accumulated counts and encoder positions.

Lower 16 bits are allocated from the lowest address to higher ones, higher 16 bits in turn.

Lower 16 bits

Higher 16 bits

■ BCD DATA (32-bit data, models: R3-BA32A, BC32A, etc.)

32-bit binary data is used for BCD.

Lower 16 bits are allocated from the lowest address to higher ones, higher 16 bits in turn.

Lower 16 bits

Higher 16 bits

■ 16-POINT DISCRETE DATA (models: R3-DA16, DC16, etc.)

Input 1 (Output 1)

Input 2 (Output 2)

Input 3 (Output 3)

Input 16 (Output 16)

0 : OFF

1 : ON

R3-NP1 SPECIFICATIONS

ES-8418 Rev.15 Page 4/5

https://www.m-system.co.jp/

MODEL: R3-NP1

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]

27.5 [1.08]

6.1

109 [4.29]

POSITIONING

GUIDE

[.24]

6–M3

SCREW

TERMINAL

COVER

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Note: In order to improve EMC performance, bond the FG terminal to ground.

Caution: FG terminal is NOT a protective conductor terminal.

LED ROTARY SW

Isolation

PROFIBUS

Control

Circuit

Communication

Circuit

INTERNAL BUS

DIP SW

RUN +

INTERNAL POWER

RUN CONTACT OUTPUT

RUN –

U (+) 2

POWER INPUT

V (–) 3

JACK

CONFIGURATION JACK

*Not provided with ‘No Power Supply’ type module.

Specifications are subject to change without notice.

R3-NP1 SPECIFICATIONS

ES-8418 Rev.15 Page 5/5

https://www.m-system.co.jp/

相关型号：