R3-PA16W/CE [MSYSTEM]

Remote I/O R3 Series TOTALIZED PULSE INPUT MODULE;


型号：	R3-PA16W/CE
厂家：	M-SYSTEM
描述：	Remote I/O R3 Series TOTALIZED PULSE INPUT MODULE 输入元件
文件：	总6页 (文件大小：145K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: R3-PA16

/C02: Polyurethane coating

Remote I/O R3 Series

/C03: Rubber coating

EX-FACTORY SETTING

TOTALIZED PULSE INPUT MODULE

(Pi 16 points)

/SET: Preset according to the Ordering Information Sheet

(No. ESU-8389)

27.5 [1.08]

RELATED PRODUCTS

• Interface module (model: R3-NC1, R3-NC3, R3-NE1,

R3-NM1, R3-NDx, R3-NFL1, R3-NP1, R3-NFx, R3-NML3.

R3-NF2: Firmware version V0.05 or later)

Note:

130

[5.12]

• Count reset by host PC/PLC:

109

[4.29]

Available with this unit and the above mentioned interface

modules of firmware version V2.00 or later, except R3-NFx.

Notice that Count reset by host PC/PLC via R3-NFx or

interface module of previous versions of firmware is unable.

• Count preset by host PC/PLC:

mm [inch]

MODEL: R3-PA16[1][2]

It is only available in combination with this unit displayed

'SW3-4 RESET/PRESET' on the right side panel and the

interface module R3-NM1 or R3-NE1 of firmware version

V2.00 or later. Count preset is not available for other

combination.

ORDERING INFORMATION

• Code number: R3-PA16[1][2]

Specify a code from below for each of [1] and [2].

(e.g. R3-PA16W/A/CE/PRS/Q)

Notice that this function is not available in the same time as

count preset by host PC/PLC.

• Specify the specification for option code /Q

(e.g. /C01/SET)

GENERAL SPECIFICATIONS

Connection

NO. OF CHANNELS

16: 16

Internal bus: Via the Installation Base (model: R3-BSx)

Input: M3 separable screw terminal (torque 0.5 N·m)

Internal power: Via the Installation Base (model: R3-BSx)

Screw terminal: Nickel-plated steel

[1] COMMUNICATION MODE

S: Single

Isolation: Input to internal bus or internal power

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with excitation abnormality;

W: Dual

[2] OPTIONS (multiple selections)

Excitation

Blank: Internal (negative common)

/A: External (24 V DC, negative common)

Standards & Approvals

Green in normal operating conditions.

blank: Without CE

Input status indicator: Red LED; turns on with the input ON.

Count reset: Via DIP switch on the side or one pulse to reset

input

/CE: CE marking

EX-FACTORY SETTING

blank: Enable count reset by host PC/PLC

/PRS: Enable count preset by host PC/PLC

Other Options

Count setting from host PC/PLC: Count reset/count preset is

changeable via DIP switch on the side.

blank: none

/Q: Option other than the above (specify the specification)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

R3-PA16 SPECIFICATIONS

ES-8389 Rev.12 Page 1/6

https://www.m-system.co.jp/

MODEL: R3-PA16

INPUT SPECIFICATIONS

FUNCTIONS

Number of input: 16 points

■ MANUAL COUNT RESET

Input resistance: 6 kΩ

1) Remove Network Module or its cables and interrupt

communication with other devices.

Common: Negative commons, all points

Maximum frequency: 100 Hz (ON/OFF time ≥ 5 msec.)

This unit is designed to be able to accept a frequency up to

100 Hz, however, ‘chattering’ contact must be avoided for

accurate measuring of such high frequency. Use mercury

relays or similar ones that do not cause any chattering.

Totalized pulse range: 1 – 10000 (‘0’ at reset)

Max. pulse range selectable from 1 to 65535 using the

R3CON PC Configurator Software. Refer to the R3CON Users

Manual for detailed information.

2) Turn ON the Count Reset SW.

3) Return the module to the base and turn the power supply

on.

4) ERR LED turns on and the module starts resetting its

counter. When the resetting is complete, the LED turns to

green. DO NOT remove the power while the red LED is on.

The RUN LED starts blinking at the same time.

5) After the green LED is confirmed, turn the power supply

off.

Count at overflow: Reset and restart at ‘1.’

■ R3-PA16x (internal excitation)

6) Turn OFF the Count Reset SW.

7) Return the Network module onto the base and turn the

power supply on.

Sensing voltage: 13 V DC (max. 24 V with no load)

ON current: ≥ 1.5 mA (≤ 1.5 kΩ)

Note: Count Reset SW must be turned OFF after this

procedure because the module does not start counting with

ON state.

OFF current: ≤ 0.75 mA (≥ 18 kΩ)

■ R3-PA16x/A (external excitation)

Sensing voltage: 24 V DC

■ REMOTE COUNT RESET INPUT

ON current: ≥ 1.5 mA (≤ 12 kΩ)

With the Count Reset Input SW (SW3-3) turned ON, the Pi 16

pulse input can be used to remotely reset the count values.

SW3-3 = OFF: Pi 16 is used as a pulse input.

SW3-3 = ON: Pi 16 is used to reset the count values for the

Pi 1 through Pi 15. One pulse supplied at the Pi 16 will be

recognized as a reset signal.

OFF current: ≤ 0.75 mA (≥ 36 kΩ)

INSTALLATION

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Installation Base (model: R3-BSx)

Weight: 200 g (0.44 lb)

■ REMOTE COUNT RESET OPERATION

1) ERR LED turns on (red color) when the reset signal is

received.

2) In 1 second, the module starts resetting its counter.

When the resetting is complete, the LED turns to green.

3) After 1 second, ERR LED turns back to the state before

the reset signal has been received.

PERFORMANCE

Data allocation: 16

Current consumption:

Note: Reset signals received while the module is processing

(1) through (3) are ignored.

R3-PA16x: 100 mA

R3-PA16x/A: 80 mA

■ COUNT RESET FROM HOST PC/PLC

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @ 1 minute

(input to internal bus or internal power)

2000 V AC @ 1 minute (power input to FG; isolated on the

power supply module)

Refer to “COUNTER SETTING FROM HOST PC/PLC” section

hereafter.

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

RoHS Directive

R3-PA16 SPECIFICATIONS

ES-8389 Rev.12 Page 2/6

https://www.m-system.co.jp/

MODEL: R3-PA16

EXTERNAL VIEW

■ FRONT VIEW

RUN LED

■ SIDE VIEW

Status Indicator LED

ERR LED

Functions

SW3

Count Setting

from Host PC/PLC

Count Reset Input

Count Reset

Set the Count Reset SW to OFF to start counting.

R3-PA16 SPECIFICATIONS

ES-8389 Rev.12 Page 3/6

https://www.m-system.co.jp/

MODEL: R3-PA16

COUNTER SETTING FROM HOST PC/PLC

■ COUNTER RESET

(Available for R3-NC1, R3-NC3, R3-NE1, R3-NM1, R3-NDx, R3-NFL1, R3-NP1, R3-NML3 (Firmware version 2.00 or later))

Setting SW3-4 OFF and turning power on enable the function.

The bits indicating the channels to reset counter are allocated in the !rst word from host PC/PLC.

When these bits are changed from 0 to 1, the counter is reset. When it is con!rmed that the counter is reset, return to 0.

Notice that if the bit remains at 1, the next reset will not work.

Count reset CH.1

Count reset CH.2

Count reset CH.3

Count reset CH.4

Count reset CH.16

■ COUNTER PRESET

(Available in combination with R3-NE1, R3-NM1 (Firmware version 2.00 or later), and R3-PA16 displayed ‘SW3-4 RESET/PRESET’

on the right side)

Setting SW3-4 ON and turning power on enable the function.

Write the preset value to the Holding Resisters, which has same address as the Input Resisters.

• Input Resisters

• Holding Resisters

Address

n+0

Address

n+0

Preset value of Input 1

Preset value of Input 2

Preset value of Input 3

Preset value of Input 4

Input 1

Input 2

Input 3

n+1

n+2

n+3

Input 4

n+3

n+14

n+15

n+14

n+15

Preset value of Input 15

Preset value of Input 16

Input 15

Input 16

R3-PA16 SPECIFICATIONS

ES-8389 Rev.12 Page 4/6

https://www.m-system.co.jp/

MODEL: R3-PA16

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]

27.5 [1.08]

109 [4.29]

POSITIONING

GUIDE

20–M3

SCREW

TERMINAL

COVER

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

■

OPTION: Blank

■ OPTION: /A

STATUS

RUN LED ERR LED INDICATOR LED

Input Circuit

INTERNAL BUS A

Communication

Circuit

Pi 1

Pi 2

Pi 1

Pi 2

INTERNAL BUS B *

Control

Circuit

Pi 3

INTERNAL POWER

Pi 4

Pi 5

DIP SW

Pi 6

Pi 7

Pi 8

Pi 9

Pi 10

Pi 11

Pi 12

Pi 13

Pi 14

Pi 15

Pi 16

Pi 10

Pi 11

Pi 12

Pi 13

Pi 14

Pi 15

Pi 16

COM(+)

+24V

Numbers in italic indicate LED No.s assigned to the front panel LEDs.

* For dual redundant communication.

**DO NOT use the terminals No. 9 and 19.

R3-PA16 SPECIFICATIONS

ES-8389 Rev.12 Page 5/6

https://www.m-system.co.jp/

MODEL: R3-PA16

Specifications are subject to change without notice.

R3-PA16 SPECIFICATIONS

ES-8389 Rev.12 Page 6/6

https://www.m-system.co.jp/

相关型号：