R3-PA4BS/Q [MSYSTEM]
Remote I/O R3 Series LOW SPEED TOTALIZED PULSE INPUT MODULE;型号: | R3-PA4BS/Q |
厂家: | M-SYSTEM |
描述: | Remote I/O R3 Series LOW SPEED TOTALIZED PULSE INPUT MODULE 输入元件 |
文件: | 总5页 (文件大小:135K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: R3-PA4B
Internal power: Via the Installation Base (model: R3-BSx)
Screw terminal: Nickel-plated steel
Remote I/O R3 Series
Isolation: Input 1 to input 2 to input 3 to input 4 to internal
bus or internal power
LOW SPEED TOTALIZED PULSE INPUT MODULE
(4 points, isolated)
Input gain: Selectable with the side DIP SW
RUN indicator: Bi-color (red/green) LED;
Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.
ERR indicator: Bi-color (red/green) LED;
Red with input abnormality;
27.5 (1.08)
130
(5.12)
Green in normal operating conditions.
Count reset: Via DIP switches on the side
109
(4.29)
mm (inch)
INPUT SPECIFICATIONS
■ Sensor Excitation
MODEL: R3–PA4B[1][2]
Voltage: 12 V DC ±10 %
Current: 15 mA
Current limiting circuit: Approx. 30 mA
■MAXIMUM FREQUENCY: 100 Hz
ORDERING INFORMATION
• Code number: R3-PA4B[1][2]
Specify a code from below for each of [1] and [2].
(e.g. R3-PA4BW/Q)
Minimum pulse width requirement: 5 msec. for both ON and
OFF
■DIVIDING RATIO: 1 – 50000 (programmable using the
R3CON PC Configurator software;
• Specify the specification for option code /Q
(e.g. /C01/SET)
factory setting ‘1’)
■COUNT RANGE: 1 – 100 000 000 (0 at reset)
Min. and max. pulse range selectable using the R3CON PC
Configurator Software. Refer to the R3CON Users Manual for
detailed information.
NO. OF CHANNELS
4B: 4 channels, low speed totalized pulse input
Count at overflow: Reset and restart at ‘1.’
Recount start value at over flow: 0 or 1
Maximum count: 1000 – 800 000 000
■DETECTING LEVEL
[1] COMMUNICATION MODE
S: Single
W: Dual
Detecting level: 15 – 100 %
[2] OPTIONS
blank: none
(of voltage across the terminals)
Factory setting: 50 % (programmable using the R3CON PC
Configurator software)
/Q: With options (specify the specification)
Current limiting circuit: Approx. 30 mA
Note 1. Each channel has three sets of input terminals.
Input terminal 1: 2 – 5, 7 – 10, 12 – 15, 17 – 20
Input terminal 2: 3 – 5, 8 – 10, 13 – 15, 18 – 20
Input terminal 3: 4 – 5, 9 – 10, 14 – 15, 19 – 20
Note 2. Gain 1 or Gain 2 selectable with the side DIP SW.
Note 3. Measured as 0 % below 15 % of the range.
■THRESHOLD
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
EX-FACTORY SETTING
/SET: Preset according to the Ordering Information Sheet
(No. ESU-8387)
Pulse logic is detected by comparing input pulse voltage
and the detecting level. Detecting ‘Rise’ or ‘Sink’ can be
switched by using the R3CON PC Configurator software;
factory setting ‘Rise’)
GENERAL SPECIFICATIONS
Connection
■ Open Collector (input terminal 3, gain 1)
Sensor excitation: 12 V DC
Internal bus: Via the Installation Base (model: R3-BSx)
Input: M3 separable screw terminal (torque 0.5 N·m)
Pull-up resistance: 20 kΩ (shorted across 1 – 3, 6 – 8, 11 –
R3-PA4B SPECIFICATIONS
ES-8383 Rev.7 Page 1/5
http://www.m-system.co.jp/
MODEL: R3-PA4B
13, 16 – 18 respectively)
procedure because the module does not start counting with
ON state.
ON voltage: ≤ 1.5 V (≤ 2 kΩ recommended)
OFF voltage: ≥ 2.5 V (≥ 20 kΩ recommended)
(Set detecting level 50 % when the saturation voltage is not
greater than 0.8 V, set 70 % when the saturation voltage is
between 0.8 to 1.5 V.)
■ Voltage Pulse (input terminals 1 and 2)
Waveform: Square, sine or similar waveforms
Input impedance: 100 kΩ minimum at input terminal 1
20 kΩ minimum at input terminal 2
Operational voltage across the terminals:
0 – 50 V (input terminal 1, gain 1)
0 – 25 V (input terminal 1, gain 2)
0 – 12 V (input terminal 2, gain 1)
0 – 6 V (input terminal 2, gain 2)
INSTALLATION
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Installation Base (model: R3-BSx)
Weight: 200 g (0.44 lb)
PERFORMANCE
Data allocation: 8
Current consumption:
80 mA (with no load at the sensor excitation)
130 mA (15 mA at each excitation)
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute (input 1 to input
2 to input 3 to input 4 to internal bus or internal power)
2000 V AC @ 1 minute (power input to FG; isolated on the
power supply module)
FUNCTIONS
■ MANUAL COUNT RESET
1) Remove Network Module or its cables and interrupt
communication with other devices.
2) Turn ON the Count Reset SW.
3) Return the module to the base and turn the power supply
on.
4) ERR LED turns on and the module starts resetting its
counter. When the resetting is complete, the LED turns to
green. DO NOT remove the power while the red LED is on.
The RUN LED starts blinking at the same time.
5) After the green LED is confirmed, turn the power supply
off.
6) Turn OFF the Count Reset SW.
7) Return the Network module onto the base and turn the
power supply on.
Note: Count Reset SW must be turned OFF after this
R3-PA4B SPECIFICATIONS
ES-8383 Rev.7 Page 2/5
http://www.m-system.co.jp/
MODEL: R3-PA4B
EXTERNAL VIEW
■FRONT VIEW
RUN LED
■SIDE VIEW
ERR LED
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
SW3
ON
SW2
SW1
4
3
2
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Gain
Count Reset
ON
ON
Set the Count Reset SW to OFF to start counting.
OUTPUT DATA DESCRIPTIONS
ADDRESS
CONTENTS
+0
+1
Input 1 totalized value (lower 16 bits)
Input 1 totalized value (upper 16 bits)
+2
+3
Input 2 totalized value (lower 16 bits)
Input 2 totalized value (upper 16 bits)
+4
+5
Input 3 totalized value (lower 16 bits)
Input 3 totalized value (upper 16 bits)
+6
+7
Input 4 totalized value (lower 16 bits)
Input 4 totalized value (upper 16 bits)
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
27.5 (1.08)
109 (4.29)
POSITIONING
GUIDE
1
11
2
20–M3
SCREW
12
3
13
4
14
5
15
6
16
7
17
8
18
9
19
10
20
TERMINAL
COVER
R3-PA4B SPECIFICATIONS
ES-8383 Rev.7 Page 3/5
http://www.m-system.co.jp/
MODEL: R3-PA4B
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
RUN LED ERR LED DIP SW
Isolation
INTERNAL BUS A
Sensor
Excitation
Communication
Circuit
EXC +
1
INTERNAL BUS B*
Input
Circuit
INP TERM. 1
INP TERM. 2
INP TERM. 3
COM
2
3
4
5
6
Input 1
INTERNAL POWER
Isolation
Isolation
Isolation
Sensor
Excitation
EXC +
Input
Circuit
INP TERM. 1
INP TERM. 2
INP TERM. 3
7
8
9
Input 2
Control
Circuit
COM 10
Sensor
Excitation
EXC + 11
Input
Circuit
INP TERM. 1 12
INP TERM. 2 13
INP TERM. 3 14
COM 15
Input 3
Sensor
Excitation
EXC + 16
Input
Circuit
INP TERM. 1 17
INP TERM. 2 18
INP TERM. 3 19
COM 20
Input 4
*For dual redundant communication.
Input Connection Example (Input 1)
■ Open Collector
1
2
3
4
5
12V DC
20kΩ
1kΩ
7.5kΩ
■ Voltage Pulse input
• Operational voltage across the terminals: 0 − 50V, 0 − 25V
• Operational voltage across the terminals: 0 − 12V、0 − 6V
+
+
1
2
3
4
5
+
+
–
1
2
3
4
5
100kΩ
20kΩ
1kΩ
100kΩ
20kΩ
1kΩ
12V DC
12V DC
PWR
PWR
7.5kΩ
7.5kΩ
–
R3-PA4B SPECIFICATIONS
ES-8383 Rev.7 Page 4/5
http://www.m-system.co.jp/
MODEL: R3-PA4B
Specifications are subject to change without notice.
R3-PA4B SPECIFICATIONS
ES-8383 Rev.7 Page 5/5
http://www.m-system.co.jp/
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明