R3-TS8AW/Q [MSYSTEM]
Remote I/O R3 Series THERMOCOUPLE INPUT MODULE;型号: | R3-TS8AW/Q |
厂家: | M-SYSTEM |
描述: | Remote I/O R3 Series THERMOCOUPLE INPUT MODULE 输入元件 |
文件: | 总5页 (文件大小:145K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: R3-TS8A
Remote I/O R3 Series
GENERAL SPECIFICATIONS
Connection
Internal bus: Via the Installation Base (model: R3-BSx)
Input: M3 separable screw terminal (torque 0.5 N·m)
Internal power: Via the Installation Base (model: R3-BSx)
Screw terminal: Nickel-plated steel
THERMOCOUPLE INPUT MODULE
(high accuracy, 8 points, isolated)
27.5 (1.08)
Isolation: Input 1 to input 2 to input 3 to input 4 to input 5 to
input 6 to input 7 to input 8 to internal bus or internal power
Sensor type: Selectable with the side DIP SW
(Independent types selectable per group of 4 channels.)
Temperature unit: °C or °F selectable with the side DIP SW
Conversion rate: Selectable with the side DIP SW
Burnout detection: Upscale or downscale selectable with the
side DIP SW
130
(5.12)
109
(4.29)
mm (inch)
Linearization: Standard
0˚C offset: Offset is set to 0˚C based on the present input
status using the PC configurator software (model: R3CON).
Cold junction compensation: CJC sensor attached to the
input terminals
MODEL: R3-TS8A[1][2]
ORDERING INFORMATION
• Code number: R3-TS8A[1][2]
Specify a code from below for each of [1] and [2].
(e.g. R3-TS8AW/CE/Q)
RUN indicator: Bi-color (red/green) LED;
Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.
ERR indicator: Bi-color (red/green) LED;
• Specify the specification for option code /Q
(e.g. /C01/SET)
Red with burnout; Green in normal operating conditions.
NO. OF CHANNELS
8A: 8 channels, high accuracy
INPUT SPECIFICATIONS
Input resistance: 30 kΩ min.
Burnout sensing: 0.1 μA
Temperature range
[1] COMMUNICATION MODE
S: Single
Conformance Range
°C
Burnout Values
°C×100
T/C
W: Dual
Lower
Upper
+32767
+32767
K (CA)
T (CC)
-100 to +200
-100 to +200
Conformance Range
°F
-27200
-27200
[2] OPTIONS (multiple selections)
Standards & Approvals
blank: Without CE
Burnout Values
°F×10
T/C
Lower
-4000
-4000
Upper
+16520
+16520
/CE: CE marking
K (CA)
T (CC)
-148 to +392
-148 to +392
Other Options
blank: none
/Q: Option other than the above (specify the specification)
INSTALLATION
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Installation Base (model: R3-BSx)
Weight: 250 g (0.55 lb)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
EX-FACTORY SETTING
/SET: Preset according to the Ordering Information Sheet
(No. ESU-8278)
R3-TS8A SPECIFICATIONS
ES-8278 Rev.1 Page 1/5
http://www.m-system.co.jp/
MODEL: R3-TS8A
PERFORMANCE
Conversion accuracy: ±0.5°C (±0.9°F)
Conversion rate: 250 msec. or 1 sec. selectable
Data range
°C: Engineering unit value × 100 (integer)
°F: Engineering unit value × 10 (integer)
Data allocation: 8
Current consumption: 100 mA
Cold junction compensation error:
±0.5°C at 25 ±10°C
±0.9°F at 77 ±18°F
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Burnout response time: ≤ 2 sec.
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute (input 1 to input
2 to input 3 to input 4 to input 5 to input 6 to input 7 to
input 8 to internal bus or internal power)
2000 V AC @ 1 minute (power input to FG; isolated on the
power supply module)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EN 50581
EXTERNAL VIEW
■ SIDE VIEW
■ FRONT VIEW
RUN LED
1
2
15
16
17
18
19
20
21
22
23
24
25
26
27
28
ERR LED
3
4
5
SW1
SW2
SW3
6
T/C
Burnout
7
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
Input 1-4 (SW1)
or
Input 5-8 (SW2)
Temp.
Unit
Conv.
8
9
Rate
10
11
12
13
14
ON
ON
ON
R3-TS8A SPECIFICATIONS
ES-8278 Rev.1 Page 2/5
http://www.m-system.co.jp/
MODEL: R3-TS8A
INPUT DATA DESCRIPTIONS
■ ANALOG DATA (TEMPERATURE DATA)
16-bit binary data.
With °C temperature unit, raw data is multiplied by 100. For example, 25.5°C is converted into 2550.
With °F temperature unit, raw data is multiplied by 10. For example, 135.4°F is converted into 1354.
Minus temperature is converted into negative values, represented in 2’s complements.
15
0
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
27.5 (1.08)
109 (4.29)
POSITIONING
GUIDE
1
15
2
16
3
17
4
18
5
19
6
28–M3
SCREW
20
7
21
8
22
9
23
10
24
11
25
12
26
13
27
14
28
TERMINAL
COVER
R3-TS8A SPECIFICATIONS
ES-8278 Rev.1 Page 3/5
http://www.m-system.co.jp/
MODEL: R3-TS8A
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
RUN LED ERR LED DIP SW
Input Circuit
INTERNAL BUS A
+
+
+
+
+
+
+
+
Communication
Circuit
+
–
1
T/C
INTERNAL BUS B*
comp. wire
INPUT 1
–
–
–
Control
Circuit
2
3
CJC
SENSOR
INTERNAL POWER
Input Circuit
Input Circuit
Input Circuit
Input Circuit
Input Circuit
Input Circuit
Input Circuit
+
4
13
14
27
28
T/C
comp. wire
–
INPUT 2
5
6
CJC
SENSOR
+
7
T/C
comp. wire
–
INPUT 3
8
CJC
SENSOR
• Unused Input Channels
Close across the unused input terminals as shown below.
9
INPUT 1
1
INPUT 2
4
INPUT 3
7
INPUT 4
10
+
10
T/C
comp. wire
Short
CJC
–
INPUT 4
–
2
3
5
6
8
9
11
12
11
SENSOR
CJC
SENSOR
12
INPUT 5
15
INPUT 6
18
INPUT 7
21
INPUT 8
24
+
15
T/C
comp. wire
Short
–
INPUT 5
16
17
19
20
22
23
25
26
–
CJC
SENSOR
16
CJC
SENSOR
17
Unused channels left open are equal to the burnout, which
turns the red ERR LED on and sets a burnout flag at the
PLC or the host device.
Unused channels can be specified and set so on the PC
Configurator Software (model: R3CON) without needing to
short at the field terminals.
+
18
T/C
comp. wire
–
INPUT 6
–
19
CJC
SENSOR
20
+
21
T/C
comp. wire
–
INPUT 7
–
22
CJC
SENSOR
23
+
24
T/C
comp. wire
–
INPUT 8
–
25
CJC
SENSOR
26
*For dual redundant communication.
R3-TS8A SPECIFICATIONS
ES-8278 Rev.1 Page 4/5
http://www.m-system.co.jp/
MODEL: R3-TS8A
Specifications are subject to change without notice.
R3-TS8A SPECIFICATIONS
ES-8278 Rev.1 Page 5/5
http://www.m-system.co.jp/
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明