R3-WT112W [MSYSTEM]
Remote I/O R3 Series MULTI POWER INPUT MODULE;
| 型号： | R3-WT112W |
| 厂家： | 
M-SYSTEM |
| 描述： | Remote I/O R3 Series MULTI POWER INPUT MODULE 输入元件 |
| 文件： | 总5页 (文件大小：192K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: R3-WT1
Remote I/O R3 Series
[4] OPTIONS
blank: none
/Q: With options (specify the specification)
MULTI POWER INPUT MODULE
52.5 (2.07)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
130
(5.12)
/C03: Rubber coating
RELATED PRODUCTS
109
(4.29)
• PC configurator software (model: R3CON)
The R3CON is used to set up the software setting of this
module. Downloadable at M-System's web site.
mm (inch)
MODEL: R3-WT1[1][2]1[3][4]
GENERAL SPECIFICATIONS
Connection
ORDERING INFORMATION
• Code number: R3-WT1[1][2]1[3][4]
Specify a code from below for each of [1] through [4].
(e.g. R3-WT1111W/Q)
Internal bus: Via the Installation Base (model: R3-BSx)
Input: M3.5 screw terminals (torque 0.8 N·m)
Internal power: Via the Installation Base (model: R3-BSx)
Screw terminal: Nickel-plated steel
Isolation: Voltage input to current input to internal bus or
internal power
• Specify the specification for option code /Q
(e.g. /C01)
DIP switch settings:
NO. OF SYSTEMS
• Computation methods
1: 1
• Count Reset (Disable/Enable)
• Others
Refer to the instruction manual for details.
RUN indicator: Bi-color (red/green) LED;
Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.
ERR indicator: Bi-color (red/green) LED;
Red with input abnormality;
[1] CONFIGURATION
1: 3-phase / 3-wire
2: Single-phase / 2-wire
3: Single-phase / 3-wire
[2] INPUT (unbalanced load)
1: 110 V / 5 A AC
Green in normal operating conditions.
Power ON timer: Starts conversion in 10 seconds after the
power is turned on.
2: 110 V / 1 A AC
3: 220 V / 1 A AC
4: 220 V / 5 A AC
Low-end cutout: Converted data forced to 0 % for 2 % or
less input. (Selectable by using R3CON)
Computation
A: 100 V / 200 V / 1 A AC (single-phase / 3- wire)
B: 100 V / 200 V / 5 A AC (single-phase / 3- wire)
Active power, reactive power: Time division
multiplication
MEASURING VARIABLE
1: Active power / reactive power / power factor /
Power factor: Calculated with active power (P)
and reactive power (Q)
frequency / active energy / reactive energy
P
2
P + Q
2
√
[3] COMMUNICATION MODE
Frequency: One-shot
S: Single
W: Dual
R3-WT1 SPECIFICATIONS
ES-8388 Rev.6 Page 1/5
http://www.m-system.co.jp/
MODEL: R3-WT1
Weight: 300 g (0.66 lb)
INPUT SPECIFICATIONS
Frequency: 50 or 60 Hz
• Voltage Input
PERFORMANCE
Accuracy (at 23°C ±10°C or 73.4°F ±18°F, 45 – 65 Hz)
Operational range: 0 – 120 % of rating
Overload capacity: 150 % of rating for 10 sec., 120 %
continuous
Active / reactive power: ±1 %
Power factor: ±2 %
• Current Input
Frequency: ±1 %
Operational range: 0 – 120 % of rating
Overload capacity: 1000 % of rating for 3 sec., 200 % for 10
sec., 120 % continuous
Active / reactive energy: ±2 %
Magnetic field (ext. origin) effect: ± 0.5 % (400 A/m)
Conversion rate: 100 msec.
■ Power Factor Input Range:
Conversion data: 16 bits / 32 bits
-1 – lag 0 – 1 – lead 0 – -1
Data allocation: 4, 8 or 16 selectable
Current consumption: 150 mA
Data range: -1000 – 0 – 1000 – 0 – -1000 with SW2-1 set to
OFF
Response time: ≤ 2 sec. (0 – 100 % ±1 %)
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @ 1 minute (voltage input to
current input to internal bus or internal power)
2000 V AC @ 1 minute (power input to FG; isolated on the
power supply module)
A device which employs different measuring methods may
show different outputs from that of M-System's.
■ Frequency Input Range: 45 – 65 Hz
Data range: 4500 – 6500
■ACTIVE / REACTIVE POWER INPUT RANGE
•Single-phase/2-wire
USABLE
RANGE
100W
BURDEN (VA)
INPUT
VT
CT
0.1
0.5
0.1
0.5
110V / 1A
110V / 5A
220V / 1A
220V / 5A
0.2
500W
200W
0.4
1000W
•Single-phase/3-wire
USABLE
RANGE
200W
BURDEN (VA)
INPUT
VT
CT
200V / 1A
200V / 5A
0.1/phase
0.5/phase
0.2/phase
1000W
•3-phase/3-wire
USABLE
RANGE
lead
BURDEN (VA)
INPUT
VT
CT
110V / 1A
110V / 5A
220V / 1A
220V / 5A
200W /
200 var
0.1/phase
lag
0.2/phase
1000W / lead 1000 var
0.5/phase
0.1/phase
0.5/phase
lag
lead
400W /
400 var
lag
0.4/phase
2000W / lead 2000 var
lag
Reactive power data in Lead: Positive, Lag: Negative
Reactive power is invalid in single-phase systems
Choose VT and CT ratios so that the calibration range
calculated by the following equation is within the usable
range in the above table.
Measuring Wattage [W]
Calibration Range [W] =
(VT Ratio) × (CT Ratio)
INSTALLATION
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Installation Base (model: R3-BSx)
R3-WT1 SPECIFICATIONS
ES-8388 Rev.6 Page 2/5
http://www.m-system.co.jp/
MODEL: R3-WT1
EXTERNAL VIEW
■ FRONT VIEW
RUN LED
■ SIDE VIEW
1
2
3
4
5
6
7
8
9
10
ERR LED
SW3
SW2
SW1
4
3
2
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
ON
ON
ON
TRANSMISSION DATA DESCRIPTIONS
n = I/O address on the installation base
Factory setting = 1 kWh and 1 kvarh per bit.
ADDRESS
CONTENTS
n
Active power *2
Reactive power *2
Power factor *2
Frequency *2
Data address depends upon the data allocation mode as
n + 1
n + 2
n + 3
indicated below:
4 (n thr. n+3)
8 (n thr. n+7)
3
n + 4
n + 5
n + 6
n + 7
Incoming active energy (lower bits)
Incoming active energy (upper bits)
Outgoing active energy (lower bits)
Outgoing active energy (upper bits)
*
16 (n thr. n+15)
*1. Fixed at 16 for the R3-NPx.
*2. 16-bit data
3
*
*3. 32-bit data
3
n + 8
n + 9
n +10
n +11
LAG reactive energy (lower bits)
LAG reactive energy (upper bits)
LEAD reactive energy (lower bits)
*
3
*
LEAD reactive energy (upper bits)
n +12
n +13
n +14
n +15
0
0
0
0
R3CON type ID WT1****
Network module 4, 8, 16
data allocation
mode example *1
I/O DATA DESCRIPTIONS
■ 16-BIT DATA
16-bit binary data. Minus values are represented in 2’s complements.
15
0
■ 32-BIT DATA
32-bit binary data. Minus values are represented in 2’s complements.
31
upper digits
16 15
lower digits
0
R3-WT1 SPECIFICATIONS
ES-8388 Rev.6 Page 3/5
http://www.m-system.co.jp/
MODEL: R3-WT1
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
52.5 (2.07)
109 (4.29)
POSITIONING
GUIDE
1
2
3
4
5
6
7
8
9
10
10–M3.5
SCREW
TERMINAL
COVER
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
■ 3-PHASE/3-WIRE
RUN LED ERR LED DIP SW
SOURCE
1
2
3
Input Circuit
VT
FUSE
INTERNAL BUS A
U
u
P1
P2
P3
Communication
Circuit
1
2
3
4
INTERNAL BUS B*
VOLTAGE
INPUT
V
V
v
v
Control
Circuit
U
u
INTERNAL POWER
LOAD
SOURCE
1
2
3
9
K
K
10
Input Circuit
k
1S
1L
3S
3L
5
6
7
8
k
CURRENT
INPUT
CT
l
l
L
L
LOAD
*For dual redundant communication.
■ SINGLE-PHASE/2-WIRE
RUN LED ERR LED DIP SW
SOURCE
1
2
Input Circuit
VT
FUSE
INTERNAL BUS A
U
V
u
P1
P2
Communication
Circuit
1
2
3
4
VOLTAGE
INPUT
INTERNAL BUS B*
v
LOAD
Control
Circuit
SOURCE
INTERNAL POWER
1
2
K
Input Circuit
9
k
l
1S
1L
5
6
7
8
CURRENT
INPUT
10
CT
L
LOAD
*For dual redundant communication.
R3-WT1 SPECIFICATIONS
ES-8388 Rev.6 Page 4/5
http://www.m-system.co.jp/
MODEL: R3-WT1
■ SINGLE-PHASE/3-WIRE
RUN LED ERR LED DIP SW
SOURCE
1
N
2
Input Circuit
VT
FUSE
INTERNAL BUS A
U
u
P1
P0
P2
Communication
Circuit
1
2
3
4
INTERNAL BUS B*
VOLTAGE
INPUT
V
V
v
v
Control
Circuit
U
u
INTERNAL POWER
LOAD
SOURCE
1
N 2
9
K
K
10
Input Circuit
k
1S
1L
2S
2L
5
6
7
8
k
CURRENT
INPUT
CT
l
l
L
L
LOAD
*For dual redundant communication.
Specifications are subject to change without notice.
R3-WT1 SPECIFICATIONS
ES-8388 Rev.6 Page 5/5
http://www.m-system.co.jp/
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明