R3S-DC8S/Q [MSYSTEM]

Remote I/O R3 Series DISCRETE OUTPUT MODULE;


型号：	R3S-DC8S/Q
厂家：	M-SYSTEM
描述：	Remote I/O R3 Series DISCRETE OUTPUT MODULE 输出元件
文件：	总5页 (文件大小：149K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: R3S-DC8

Output: Separable tension clamp terminal (applicable wire

Remote I/O R3 Series

size: 0.2 to 1.5 mm , stripped length 10 mm)

Internal power: Via the Installation Base (model: R3-BSx)

Isolation: Output 1 to output 2 to output 3 to output 4 to

output 5 to output 6 to output 7 to output 8 to internal bus

or internal power

DISCRETE OUTPUT MODULE

(Do 8 points (relay), tension clamp terminal block)

27.5 (1.08)

Output hold setting: Setting for communication error with

side DIP SW

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Green LED turns on in normal operating

conditions.

130 (5.12)

120 (4.72)

mm (inch)

Output status indicator:

1 to 8: Red LED; turns on with the output ON.

9 to 16: Unused

MODEL: R3S–DC8[1][2]

OUTPUT SPECIFICATIONS

Output: Relay contact, 8 points

ORDERING INFORMATION

• Code number: R3S-DC8[1][2]

Specify a code from below for each of [1] and [2].

(e.g. R3S-DC8W/CE/Q)

Common: 1 point 1 common (8 terminals)

Maximum load current: 2.0 A per point

Relay driving power: 24 V DC ±10 %, ≥ 60 mA

Maximum outputs applicable at once: No limit (at 24 V DC)

Contact rating: 250 V AC @ 2 A (cos ø = 1)

30 V DC @ 2 A (resistive load)

• Specify the specification for option code /Q

(e.g. /C01)

NO. OF CHANNELS

8: 8

Maximum switching voltage: 250 V AC or 30 V DC

Maximum switching power: 500 VA or 60 W

Minimum load: 5 V DC @ 1 mA

Mechanical life: 2 × 10 cycles (300 cycle/min.)

[1] COMMUNICATION MODE

S: Single

When driving an inductive load, external protection is

recommended.

W: Dual

ON delay: ≤ 10 msec.

OFF delay: ≤ 10 msec.

[2] OPTIONS (multiple selections)

Standards & Approvals

blank: Without CE

INSTALLATION

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Installation Base (model: R3-BSx)

Weight: 190 g (0.42 lb)

/CE: CE marking

Other Options

blank: none

/Q: Option other than the above (specify the specification)

SPECIFICATIONS OF OPTION: Q

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

GENERAL SPECIFICATIONS

Connection

Internal bus: Via the Installation Base (model: R3-BSx)

R3S-DC8 SPECIFICATIONS

ES-8941 Rev.3 Page 1/5

https://www.m-system.co.jp/

MODEL: R3S-DC8

PERFORMANCE

Data allocation: 1

Current consumption: Approx. 60 mA

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @ 1 minute

(output 1 to output 2 to output 3 to output 4 to output 5 to

output 6 to output 7 to output 8 to internal bus or internal

power)

2000 V AC @ 1 minute (power input to FG;

isolated on the power supply module)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1, EN 61010-2-201

Measurement Category II (output)

Pollution Degree 2

Output to internal bus or internal power: Basic insulation

(250 V)

RoHS Directive

FUNCTIONS

■OUTPUT HOLD or OUTPUT OFF

In normal conditions, the module outputs the signal from

the preferred bus A.

When an error is detected, the output is switched to the

data from the bus B.

• Output Hold

If both are in error, the module holds the signal and stands

by until one of the communications recovers.

• Output OFF

If both are in error, the module outputs OFF signals and

stands by until one of the communications recovers.

At the startup, it outputs OFF until the communication is

established and normal data is received.

R3S-DC8 SPECIFICATIONS

ES-8941 Rev.3 Page 2/5

https://www.m-system.co.jp/

MODEL: R3S-DC8

EXTERNAL VIEW

■ FRONT VIEW

■ SIDE VIEW

RUN LED

Output Status Indicator LEDs

ERR LED

SW3

Output

Hold

EXTERNAL DIMENSIONS unit: mm [inch]

120 (4.72)

27.5 (1.08)

109 (4.29)

POSITIONING

GUIDE

R3S-DC8 SPECIFICATIONS

ES-8941 Rev.3 Page 3/5

https://www.m-system.co.jp/

MODEL: R3S-DC8

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

STATUS

ERR INDICATOR

RUN

LED

DIP SW

Output

Circuit

LED

INTERNAL BUS A

Communication

Circuit

Do 1

*INTERNAL BUS B

COM 1

Do 2

COM 2

Do 3

INTERNAL POWER

COM 3

Do 4

COM 4

Do 5

Control

Circuit

10 COM 5

11 Do 6

12 COM 6

13 Do 7

14 COM 7

15 Do 8

16 COM 8

17 +24V

18 +24V

19 0V

24V DC

20 0V

Numbers in italic indicate LED No.s assigned to the front panel LEDs.

*For dual redundant communication.

■ Output Connection Examples

ࠉ

1 point 1 common

Do 1

COM 1

－

＋

－

Do 8 15

COM 8 16

－

＋

－

R3S-DC8 SPECIFICATIONS

ES-8941 Rev.3 Page 4/5

https://www.m-system.co.jp/

MODEL: R3S-DC8

OUTPUT TERMINAL ASSIGNMENT

PIN No.

FUNCTION

Do1

COM1

Do2

COM2

Do3

COM3

Do4

COM4

Do5

COM5

Do6

COM6

Do7

COM7

Do8

COM8

+24V

Specifications are subject to change without notice.

R3S-DC8 SPECIFICATIONS

ES-8941 Rev.3 Page 5/5

https://www.m-system.co.jp/

相关型号：