R5-PSK [MSYSTEM]

Remote I/O R5 Series;


型号：	R5-PSK
厂家：	M-SYSTEM
描述：	Remote I/O R5 Series
文件：	总3页 (文件大小：99K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: R5-PS

master device (PLD or PC etc.), RUN contact output of Power

Supply Module turns ON.

Remote I/O R5 Series

• When using with dual redundant communication or two

system.

POWER SUPPLY MODULE

During both Network Module or one of them communicates

normally with a master device (PLD or PC etc.), RUN contact

output of Power Supply Module turns ON.

45 (1.77)

• When using R5-PS with redundant or two system.

RUN contact output works in same function for both cases.

However, when I/O capacity code of installation base is

"05:5 slots (single communication mode)" or "09: 9 slots

(single communication mode)", the RUN contact output of

Power Supply Module installed in a Extender Power Module

Base (model: R5-EX1) is not available.

(3.54)

mm (inch)

MODEL: R5–PS[1][2]

GENERAL SPECIFICATIONS

Connection

ORDERING INFORMATION

• Code number: R5-PS[1][2]

•Power input or RUN contact output: M3.5 screw terminals

(torque 0.8 N·m)

Specify a code from below for each of [1] and [2].

(e.g. R5-PSR/Q)

•Internal bus or internal power: Via the Installation Base

(model: R5-BS)

• Specify the specification for option code /Q

(e.g. /C01/S01)

Screw terminal: Nickel-plated steel (standard) or stainless

steel

Isolation: Internal bus or internal power to power supply to

RUN contact output to FG

[1] POWER INPUT

Power LED: Bi-color (red/amber) LED;

Red when the power is supplied; Amber at RUN contact

output ON.

AC Power

K: 100 – 120 V AC

(Operational voltage range 85 – 132 V, 47 – 66 Hz)

L: 200 – 240 V AC

■ RUN CONTACT OUTPUT

Contact turns ON (closed) while data from the host is

normally received; OFF (open) with loss of communication

for approx. 3 seconds.

(Operational voltage range 170 – 264 V, 47 – 66 Hz)

DC Power

R: 24 V DC

Rated load: 250 V AC @ 0.5 A (cos ø = 1)

30 V DC @ 0.5 A (resistive load)

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

Maximum switching voltage: 250 V AC or 30 V DC

Maximum switching power: 250 VA or 150 W

Minimum load: 1 V DC @ 1 mA

[2] OPTIONS

blank: none

/Q: With options (specify the specification)

Mechanical life: 2 × 10 cycles (rate 300 cycles/min.) When

driving an inductive load, external contact protection and

noise quenching recommended.

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

INSTALLATION

Power consumption

/C02: Polyurethane coating

/C03: Rubber coating

•AC: Approx. 90 VA

TERMINAL SCREW MATERIAL

/S01: Stainless steel

•DC: Approx. 45 W or 1.8 A

Output current: 1.5 A continuous at 21 V DC;

(Total current continuously consumed at the network

modules and I/O modules must be within 1.5 A.)

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

NOTICE

■ RUN CONTACT OUTPUT

• Function of RUN contact output

During a Network Module communicates normally with a

R5-PS SPECIFICATIONS

ES-6110 Rev.14 Page 1/3

https://www.m-system.co.jp/

MODEL: R5-PS

Mounting: Installation Base (model: R5-BS) or Extender

Power Supply Module Base (R5-EX1)

Weight: 250 g (0.55 lb)

PERFORMANCE

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @ 1 minute (Internal bus or

internal power to power input to RUN output to FG)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1, EN 61010-2-201

Measurement Category II (RUN contact output)

Installation Category II (power input)

Pollution Degree 2

Internal power or RUN contact output to power input to FG:

Reinforced insulation (300 V)

Internal power to RUN contact output: Basic insulation

(300 V)

RoHS Directive

EXTERNAL VIEW

POWER

Power LED

R5-PS SPECIFICATIONS

ES-6110 Rev.14 Page 2/3

https://www.m-system.co.jp/

MODEL: R5-PS

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]

LOCKING CLAMP

45 (1.77)

90 (3.54)

POSITIONING GUIDE

5–M3.5 TERMINAL SCREW

7 (.28)

TERMINAL COVER

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

POWER LED

Isolation

U (+)

V (–)

INTERNAL POWER

POWER INPUT

Control

Circuit

*FG

RUN +

RUN –

RUN CONTACT OUTPUT

INTERNAL BUS

*In order to improve EMC performance, bond the FG terminal to ground.

Caution: This terminal is NOT a protective conductor terminal.

Specifications are subject to change without notice.

R5-PS SPECIFICATIONS

ES-6110 Rev.14 Page 3/3

https://www.m-system.co.jp/

相关型号：