R5T-PC22S/Q [MSYSTEM]

Remote I/O R5 Series PULSE OUTPUT MODULE;


型号：	R5T-PC22S/Q
厂家：	M-SYSTEM
描述：	Remote I/O R5 Series PULSE OUTPUT MODULE 输出元件
文件：	总3页 (文件大小：119K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: R5T-PC2

steel

Remote I/O R5 Series

Isolation: Po 1 to Po 2 to internal bus or internal power

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

PULSE OUTPUT MODULE

(screw terminal block; photo MOSFET relay output, 2 points)

Green when the bus B operates normally;

Amber when both buses operate normally.

Output status indicator: Red LED; turns on with the outputs

ON.

18 (.71)

Pulse width adjustment: 5 msec., 10 msec., 50 msec., 100

msec., 500 msec., 1 sec., 1.5 sec., 2 sec. (Side DIP SW)

Count reset: Via DIP switches on the side

(3.54)

137

(5.39)

OUTPUT SPECIFICATIONS

mm (inch)

Output: Photo MOSFET relay contact, 2 points

Common: Each point independent

Rated load: 125 V AC/DC @ 50 mA (resistive load)

Maximum ON resistance: 50 Ω

MODEL: R5T–PC2[1][2]

Maximum frequency: 100 Hz (DIP SW selectable)

Totalized pulse range: 1 – 10000 (‘0’ at reset)

(Max. pulse range selectable from 100 to 60000 using the

R5CON PC Configurator Software. Refer to the R5CON Users

Manual for detailed information.)

ORDERING INFORMATION

• Code number: R5T-PC2[1][2]

Specify a code from below for each of [1] and [2].

(e.g. R5T-PC2W/Q)

• Specify the specification for option code /Q

(e.g. /C01/S01)

Count at overflow: Reset and restart at ‘1.’

INSTALLATION

NO. OF CHANNELS

2: 2-point outputs

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Installation Base (model: R5-BS)

Weight: 110 g (0.24 lb)

[1] COMMUNICATION MODE

S: Single

W: Dual

PERFORMANCE

Data allocation: 2

[2] OPTIONS

blank: none

Response time: ≤ 0.1 sec.

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @ 1 minute

(Po 1 to Po 2 to internal bus or internal power)

2000 V AC @ 1 minute (power input to FG;

isolated on the power supply module)

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

GENERAL SPECIFICATIONS

Connection

Internal bus: Via the Installation Base (model: R5-BS)

Output: M3.5 screw terminal block (torque 0.8 N·m)

Internal power: Via the base (model: R5-BS)

Screw terminal: Nickel-plated steel (standard) or stainless

R5T-PC2 SPECIFICATIONS

ES-7574 Rev.9 Page 1/3

https://www.m-system.co.jp/

MODEL: R5T-PC2

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1, EN 61010-2-201

Measurement Category II (output)

Pollution Degree 2

Output to internal bus or internal power – Basic insulation

(300 V)

RoHS Directive

FUNCTIONS

■ Counter reset

1) Remove Network Module or its cables and interrupt

communication with other devices.

2) Turn ON the Counter Reset SW (SW8) on the module.

3) Return the module to the base and turn the power supply

on.

4) Red RUN LED turns on and the module starts resetting its

counter. When the resetting is complete, the LED light turns

to green. DO NOT remove the power while the red light is

on.

5) After the green LED is confirmed, turn the power supply

off.

6) Turn OFF the Counter Reset SW (SW8).

7) Return the Network module onto the base and turn the

power supply on.

Note: Counter Reset SW must be turned OFF after this

procedure because the module does not start counting with

ON state.

EXTERNAL VIEW

■ SIDE VIEW

■ FRONT VIEW

RUN LED

Status Indicator LED

RUN

1 2 3 4 5 6 7 8

OFF

Counter

Reset

Pulse Width

Unused

Counter Reset SW is normally OFF during operation.

R5T-PC2 SPECIFICATIONS

ES-7574 Rev.9 Page 2/3

https://www.m-system.co.jp/

MODEL: R5T-PC2

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]

LOCKING CLAMP

18 (.71)

38.5 (1.52)

98.5 (3.88)

TERMINAL COVER

8.2 (.32)

6–M3.5

TERMINAL

SCREWS

7.2 (.28)

POSITIONING GUIDE

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

RUN OUTPUT STATUS

LED INDICATOR LED

•

• • • •

Isolation

INTERNAL BUS A

Communication

Circuit

Po 1

*INTERNAL BUS B

Control

Circuit

COM1

Po 2

INTERNAL POWER

COM2

DIP SW

*For dual redundant communication.

Note: Italic typed numbers correspond to the LEDs on the front panel.

Specifications are subject to change without notice.

R5T-PC2 SPECIFICATIONS

ES-7574 Rev.9 Page 3/3

https://www.m-system.co.jp/

相关型号：