R7FN-DAC16B-R [MSYSTEM]

Remote I/O R7 Series FLEX NETWORK I/O MODULE;


型号：	R7FN-DAC16B-R
厂家：	M-SYSTEM
描述：	Remote I/O R7 Series FLEX NETWORK I/O MODULE
文件：	总6页 (文件大小：159K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: R7FN-DAC16B

(No. ESU-7808-DAC16)

Remote I/O R7 Series

GENERAL SPECIFICATIONS

Connection: M3 separable screw terminal (torque 0.5 N·m)

Solderless terminal: Refer to the drawing at the end of the

section.

FLEX NETWORK I/O MODULE

(NPN discrete input & PNP transistor output, 8 points each)

Functions & Features

• 8 points NPN discrete input and 8 points PNP transistor

output module for FLEX NETWORK

• Communication cable

Recommended manufacture: Japan Solderless Terminal

MFG.Co.Ltd

FLEX NETWORK is registered trademark of Digital

Electronics Corporation in Japan.

Applicable wire size: 0.2 to 0.5 mm

(AWG 26 to 22)

• Others

Recommended manufacture: Japan solderless terminal

MFG.Co.Ltd, Nichifu Co.,ltd

115 (4.53)

Applicable wire size: 0.25 to 1.65 mm

(AWG 22 to 16)

Screw terminal: Nickel-plated steel

Housing material: Flame-resistant resin (gray)

Isolation: I/O to FLEX NETWORK to power to FG

Output at the loss of communication:

Output hold (*), Output clear

53 (2.09)

54 (2.13)

mm (inch)

Selectable with the front DIP SW

(*) factory default setting

MODEL:R7FN–DAC16B–R[1]

Status indicator LED: PWR, RUN

(Refer to the instruction manual)

Discrete I/O status indicator LED: LED turns on with I/O ON

■Recommended solderless terminal

ORDERING INFORMATION

• Code number: R7FN-DAC16B-R[1]

Specify a code from below for [1].

(e.g. R7FN-DAC16B-R/Q)

3.3 (.13) max

• Specify the specification for option code /Q

(e.g. /C01/SET)

mm (inch)

I/O TYPE

DAC16B: NPN discrete input &

FLEX NETWORK COMMUNICATION

Communication configuration: 1: N

Connection method: Multi-drop Connection

Communication method: Cyclic Time Division, half-duplex

Communication I/F: Differential, pulse transfer isolation

Error Check: Format, bit, CRC-12 verification

Max. Number of Nodes: 63 (1008 I/O points)

Required node: 1

PNP transistor output, 8 points each

POWER INPUT

DC Power

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

Network cable: Pro-face’s following cable

FN-CABLE2010-31-MS (10 m)

[1] OPTIONS

blank: none

FN-CABLE2050-31-MS (50 m)

/Q: Options other than the above (specify the specification)

FN-CABLE2200-31-MS (200 m)

Transmission distance: 12 Mbps: 100 meters (328 ft) (*)

6 Mbps: 200 meters (656 ft)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

(*) Factory default setting

Station address: Rotary switch

(Refer to the instruction manual)

/C02: Polyurethane coating

Terminating resistor: Built-in

/C03: Rubber coating

EX-FACTORY SETTING

/SET: Preset according to the Ordering Information Sheet

R7FN-DAC16B SPECIFICATIONS

ES-7808-W Rev.0 Page 1/6

http://www.m-system.co.jp/

MODEL: R7FN-DAC16B

INPUT SPECIFICATIONS

Common: Positive common (NPN) per 8 points

Maximum inputs applicable at once: No limit (at 24 V DC)

Rated input voltage: 24 V DC ±10 %; ripple 5 %p-p max.

ON voltage / current: ≥ 15 V DC (X0 through X7 to COM) / ≥

3.5 mA

OFF voltage / current: ≤ 5 V DC (X0 through X7 to COM) / ≤

1 mA

Input current: ≤ 5.5 mA per point at 24 V DC

Input resistance: Approx. 4.4 kΩ

ON delay: ≤ 2.0 msec.

OFF delay: ≤ 2.0 msec.

OUTPUT SPECIFICATIONS

Common: Positive common (PNP) per 8 points

Maximum outputs applicable at once: No limit (at 24 V DC)

Rated load voltage: 24 V DC ±10 %

Rated output current: 0.25 A per point, 2.0 A per common

Residual voltage: ≤ 1.2 V

Leakage current: ≤ 0.1 mA

ON delay: ≤ 0.5 msec.

OFF delay: ≤ 1.5 msec.

(When driving an inductive load, connect a diode in parallel

with the load.)

INSTALLATION

Current consumption

•DC: Approx. 50 mA

Operating temperature: -10 to +55°C (14 to 131°F)

Storage temperature: -20 to +65°C (-4 to +149°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: DIN rail (35 mm rail)

Weight: 200 g (0.44 lb)

PERFORMANCE

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @ 1 minute (I/O to FLEX

NETWORK to power to FG)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

RoHS Directive

EN 50581

R7FN-DAC16B SPECIFICATIONS

ES-7808-W Rev.0 Page 2/6

http://www.m-system.co.jp/

MODEL: R7FN-DAC16B

EXTERNAL VIEW

Operating Mode Setting DIP SW (SW1)

Station Address Setting Rotary SW

Status Indicator LED

Discrete I/O Status Indicator LED

2 3 4 5 6 7 8

X10

PWR RUN

1 2 3 4 5 6 7 0 1 2 3 4 5 6 7

STATION ADD.

10 11 12 13 14 15 16 17 18

FLEX NETWORK,

Power Supply Terminals

I/O Terminals

CONNECTION DIAGRAMS

■ MASTER CONNECTION

Master Station

Slave Station

–

Terminating

Resistor

SHIELD

Terminating

Short Bar

–

Note: Be sure to use the terminator(s) located at both ends of the modules.

TERMINAL ASSIGNMENTS

■I/O TERMINAL ASSIGNMENT

＋24V X1

COM

NO.

FUNCTION

Common

Input 0

Input 2

Input 4

Input 6

Output 0

Output 2

Output 4

Output 6

NO.

FUNCTION

24V DC

Input 1

Input 3

Input 5

Input 7

Output 1

Output 3

Output 5

Output 7

COM

+24V

R7FN-DAC16B SPECIFICATIONS

ES-7808-W Rev.0 Page 3/6

http://www.m-system.co.jp/

MODEL: R7FN-DAC16B

■ NETWORK, POWER SUPPLY TERMINAL ASSIGNMENT

TR+ TR +24V 0V

JP+ JP

NO.

JP+

JP–

FUNCTION, NOTES

Terminating resistor

TR+

TR–

+24V

Network

Power input (24V DC)

Power input (0V)

I/O DATA DESCRIPTIONS

■ DISCRETE I/O

• Di

• Do

8 7

Unused

Input 0

Input 1

Input 2

Input 3

Output 0

Output 1

Output 2

Output 3

Input 7

Output 7

0: OFF

1: ON

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

115 (4.53)

17 (.66)

54 (2.13)

DIN RAIL

35mm wide

10 11 12 13 14 15 16 17 18

30 (1.18)

[5 (.20)]

6 (.24)

7–M3 SCREW

TERMINALS

18–M3 SCREW

TERMINALS for I/O

for FLEX NETWORK, POWER

R7FN-DAC16B SPECIFICATIONS

ES-7808-W Rev.0 Page 4/6

http://www.m-system.co.jp/

MODEL: R7FN-DAC16B

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Note: In order to improve EMC performance, bond the FG terminal to ground.

Caution: FG terminal is NOT a protective conductor terminal.

Isolation

Input Circuit

–

+24V

Comm.

Circuit

24V DC

Control

Circuit

COM

Output Circuit

■ Input Circuit

+24V

Control

Circuit

■ Output Circuit

10 24V

Control

Circuit

COM

■ I/O Connection Example

–

+24V 10

COM

Y7 18

R7FN-DAC16B SPECIFICATIONS

ES-7808-W Rev.0 Page 5/6

http://www.m-system.co.jp/

MODEL: R7FN-DAC16B

Specifications are subject to change without notice.

R7FN-DAC16B SPECIFICATIONS

ES-7808-W Rev.0 Page 6/6

http://www.m-system.co.jp/

相关型号：