R8-TC2P/Q [MSYSTEM]
Remote I/O R8 Series TEMPERATURE CONTROL MODULE;
| 型号： | R8-TC2P/Q |
| 厂家： | 
M-SYSTEM |
| 描述： | Remote I/O R8 Series TEMPERATURE CONTROL MODULE |
| 文件： | 总7页 (文件大小：256K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: R8-TC2
Remote I/O R8 Series
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
TEMPERATURE CONTROL MODULE
Functions & Features
/C02: Polyurethane coating
• Two PID controllers
• Universal input x 2 points, control output x 2 points, clamp
-on current sensor input x 2 points
RELATED PRODUCTS
• PC configurator software (model: R8CFG)
A dedicated cable is required to connect the module to the
PC. Please refer to the users manual for the PC configurator
for applicable cable types.
• 2 universal inputs configurable to T/C, RTD, DC current or
voltage independently
• Clamp-on current sensor input enables to detect heater
wire break or over current
• Clamp-on current sensor (model: CLSE)
• Auto tuning function
(Used for detecting the heater wire break)
Note: When using with Power/Network module (model: R8-
NECT1), firmware version Ver1.30 or later is supported.
• Configurable with PC configurator (model: R8CFG)
• Mixed installation with other I/O modules
GENERAL SPECIFICATIONS
Connection
24 (.94)
•I/O: 4-pin e-CON connector
Unit side connector XN2D-1474-S002 (Omron)
Recommended cable side connector XN2A-1470 (Omron)
115
(
)
4.53
Applicable wire size: 0.08 - 0.5 mm
2
(AWG28 - 20)
Outer sheath diameter: max. 1.5 dia
(The cable connector is not included in the package.
Refer to the specifications of the product.)
•Excitation supply, internal bus:
(
)
59 2.32
mm (inch)
Connected to internal bus connector
•Internal power: Supplied from internal bus connector
Isolation: Pv1 to Pv2 to Mv1 to Mv2 to exc.supply to CT1 or
CT2 or internal bus or internal power
MODEL: R8-TC2[1][2]
CT Input waveform
ORDERING INFORMATION
• Code number: R8-TC2[1][2]
Specify a code from below for each [1] and [2].
(e.g. R8-TC2A/Q)
RMS sensing: Up to 15 % of 3rd harmonic content
Input Selection: Selectable with the side DIP SW
Cold Junction Compensation: CJC sensor incorporated
Module address: With DIP switch
• Specify the specification for option code /Q
(e.g. /C01)
Terminating resistor: Built-in (DIP Switch, default: disable)
Indicator LEDs: Bi-color (red/green) LED;
Other indicator LEDs: Green LED
CONTROL LOOP
Refer to the instruction manual.
2: 2 loops
Control mode: Standard PID, heating and cooling control PID
Proportional band (P): 0.1 to 3200.0 (temperature unit)
Integral time (I): 0 to 3999 sec.
[1] CONTROL OUTPUT
Derivative time (D): 0.0 to 999.9 sec.
A: 0 – 20 mA DC (Load resistance 450 Ω max.) 2 points
V: 0 – 10 V DC (Load resistance 2 kΩ max.) 2 points
P: 12 V voltage pulse (Load resistance 600 Ω max.) 2 points
Auto-tuning: Limit cycle method
Sampling cycle: 100 msec.
Control cycle: 1.0 to 99.9 sec.
(100 msec. fixed for Mv output 0 - 20 mA DC
and 0 - 10 V DC)
[2] OPTIONS
blank: none
Mv output range: -5 - +105 % for output scale
Parameters: Stored in non-volatile memory; write/erase
cycle endurance: less than 1 000 000
/Q: With options (specify the specification)
Parameter setting: With PC configurator software (model:
R8-TC2 SPECIFICATIONS
ES-9788 Rev.5 Page 1/7
http://www.m-system.co.jp/
MODEL: R8-TC2
R8CFG)
OUTPUT SPECIFICATIONS
• Input
■ Control Output (Mv1, Mv2)
Specify the type of output with the code number.
• DC Current: 0 – 20 mA DC
Operational range: 0 – 23 mA DC
Load resistance: ≤ 450 Ω
• DC Voltage: 0 – 10 V DC
Operational range: 0 - 11.5 V DC
Load resistance: ≥ 2 kΩ
• Burnout
• CT input
• Auto-tuning
Refer to the instruction manual for detail.
INPUT SPECIFICATIONS
■ Universal input 1, 2 (Pv1, Pv2)
For input type and range configuration, refer to the
instruction manual.
■ Voltage Pulse
Maximum frequency: 1 Hz
Minimum pulse width: 1 msec.
Hi level: 12 V ±15 %
DC Current:
Input range: 0 - 20 mA DC
Lo level: ≤ 0.5 V
Input resistance: 49.9 Ω resistor incorporated
• DC voltage input
Load resistance: 600 Ω min.
Input resistance: ≥ 10 kΩ (-1000 to +1000 mV DC)
Input resistance: ≥ 1 MΩ (-10 to +10 V DC)
• Thermocouple
INSTALLATION
Max. current consumption: 200 mA
Exc. supply current consumption: 60 mA
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: DIN rail
Input resistance: ≥ 10 kΩ
Input range: Refer to the table 1
Burnout sensing: ≤ 4 μA
Conformance range: Refer to the table 1
• RTD (2-wire or 3-wire)
Excitation: ≤ 0.33 mA
Weight: 110 g (0.24 lb)
Input range: Refer to the table 1
Allowable leadwire resistance: 20 Ω per wire
• Resistor (2-wire or 3-wire)
Excitation: ≤ 0.33 mA
PERFORMANCE in percentage of span
Accuracy
• Pv1 or Pv2: Refer to "Input type, range & conversion
accuracy" section.
Input range: 0 - 4000 Ω
Allowable leadwire resistance: 20 Ω per wire
• Potentiometer
• CT1 or CT2: ±2 % (sensor error margin not included)
• Mv1 or Mv2: ±0.5 %
Excitation: ≤ 0.33 mA
Data allocation: 2
Input range: Refer to the table 1
Allowable leadwire resistance: 20 Ω per wire
■ Clamp-on current sensor (CT1, CT2)
(Sensor model No.: AC input)
CLSE-R5: 0 – 5 A
Module addresses in use: 8
Commmunication data:
• Loop 1 Pv1
• Loop 1 Sp1
• Loop 1 Mv1
CLSE-05: 0 – 50 A
• Loop 1 Proportional band (P1)
• Loop 1 Integral time (I1)
• Loop 1 Derivative time (D1)
• CT input 1 Current value (CT1)
• Loop 2 Pv2
CLSE-10: 0 – 100 A
CLSE-20: 0 – 200 A
CLSE-40: 0 – 400 A
CLSE-60: 0 – 600 A
Frequency: 50 / 60 Hz (45 - 65 Hz)
Operational range: 0 – 120 % of rating
Overload capacity:
• Loop 2 Sp2
• Loop 2 Mv2
• Loop 2 Proportional band (P2)
• Loop 2 Integral time (I2)
• Loop 2 Derivative time (D2)
• CT input 2 Current value (CT2)
Cold junction compensation error:
±3°C at -10 - +55°C
CLSE-R5: 10 A continuous
CLSE-05: 60 A continuous
CLSE-10: 120 A continuous
CLSE-20: 240 A continuous
CLSE-40: 480 A continuous
CLSE-60: 720 A continuous
Be sure that the input voltage is of 480 V or less.
±5.4°F at 14 - 131°F
R8-TC2 SPECIFICATIONS
ES-9788 Rev.5 Page 2/7
http://www.m-system.co.jp/
MODEL: R8-TC2
(The described accuracy may be partially not
satisfied when the input temperature is below 0°C. Consult
factory.)
Temp. coefficient
• Pv1 or Pv2: ±0.03 %/°C (± 0.02 %/°F)
• CT1 or CT2: ±0.03 %/°C (± 0.02 %/°F)
Response time
• CT1 or CT2: ≤ 2 sec. (0 – 90 %)
• Mv1 or Mv2: ≤ 1 sec. (0 – 90 %, DC output)
Burnout response time: ≤ 1 sec.
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1000 V AC @1 minute (Pv1 to Pv2 to
Mv1 to Mv2 to exc.supply to CT1 or CT2 or internal bus or
internal power to ground)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EN 50581
CONTROL MODE
Choose from two control mode shown below with
configurator software.
■ Standard PID control
It is available to control two independent loops.
Loop 1: Control by Pv1 and Mv1.
Loop 2: Control by Pv2 and Mv2.
■ Heating and cooling PID control
It is available to control one loop.
Loop 1: Control by Pv1, heating Mv1 and cooling Mv2.
Loop 2 is not available.
R8-TC2 SPECIFICATIONS
ES-9788 Rev.5 Page 3/7
http://www.m-system.co.jp/
MODEL: R8-TC2
INPUT TYPE, RANGE & CONVERSION ACCURACY
[Table 1]
INPUT TYPE
DC Current
INPUT RANGE
0 – 20mA DC
ACCURACY
±20ꢀA
DC Voltage
-1000 – +1000mV DC
When maximum range*2 is 60 mV or less: ±20ꢀV
When maximum range*2 is 120 mV or less: ±±0ꢀV
When maximum range*2 exceeds 120 mV: ±200ꢀV
-10 – +10V DC
± 200mV
Potentiometer
Resistor
0 – 150Ω, 0 – ±00Ω, 0 – 600Ω,
Larger value of either ±0ꢁ1 Ω or ±0ꢁ1 ꢂ
0 – 1200Ω, 0 – 2500Ω, 0 – 4000Ω
0 – 4000Ω
Larger value of either ±0ꢁ1 Ω or ±0ꢁ1 ꢂ
°F
°C
Thermocouple
INPUT RANGE ACCURACY*1 CONFORMANCE RANGE INPUT RANGE ACCURACY*1 CONFORMANCE RANGE
(PR)
0 – 1760
-270 – +1±70
-270 – +1000
-210 – +1200
-270 – +400
100 – 1820
-50 – +1760
-50 – +1760
0 – 2±15
±1ꢁ80
±0ꢁ40
±0ꢁ60
±0ꢁ70
±0ꢁ50
±2ꢁ00
±1ꢁ00
±1ꢁ00
±1ꢁ00
±0ꢁ50
±0ꢁ50
±0ꢁ±0
±0ꢁ±0
°C
0 – 1760
-150 – +1±70
-170 – +1000
-180 – +1200
-170 – +400
400 – 1760
200 – 1760
0 – 1760
±2 – ±200
-454 – +2498
-454 – +18±2
-±46 – +2192
-454 – +752
212 – ±±08
-58 – +±200
-58 – +±200
±2 – 4199
±±ꢁ24
±0ꢁ72
±1ꢁ08
±1ꢁ26
±0ꢁ90
±±ꢁ60
±1ꢁ80
±1ꢁ80
±1ꢁ80
±0ꢁ90
±0ꢁ90
±0ꢁ54
±0ꢁ54
°F
±2 – ±200
-2±8 – +2498
-274 – +18±2
-292 – +2192
-274 – +752
752 – ±200
±92 – ±200
±2 – ±200
K (CA)
E (CRC)
J (IC)
T (CC)
B (RH)
R
S
C (WRe 5-26)
0 – 2±15
±2 – 4199
N
-270 – +1±00
-200 – +600
-200 – +900
0 – 1±95
-1±0 – +1±00
-200 – +600
-200 – +900
0 – 1±95
-454 – +2±72
-±28 – +1112
-±28 – +1652
±2 – 254±
-202 – +2±72
-±28 – +1112
-±28 – +1652
±2 – 254±
U
L
P (Platinel ll)
RTD
INPUT RANGE
ACCURACY
±0ꢁ40
INPUT RANGE
ACCURACY
±0ꢁ72
Pt 100 (JIS ’97, IEC)
Pt 500
-200 – +850
-200 – +850
-200 – +850
-200 – +649
-200 – +510
-50 – +200
-50 – +250
-±28 – +1562
-±28 – +1562
-±28 – +1562
-±28 – +1200
-±28 – +950
-58 – +±92
±0ꢁ40
±0ꢁ72
Pt 1000
±0ꢁ40
±0ꢁ72
Pt 50Ω (JIS ’81)
JPt 100 (JIS ’89)
Ni 508ꢁ4 Ω
±0ꢁ60
±1ꢁ08
±0ꢁ40
±0ꢁ72
±0ꢁ60
±1ꢁ08
Cu 10 @25°C
±2ꢁ00
-58 – +482
±±ꢁ60
*1ꢁ Thermocouple: CJC error margin (±ꢁ0 °C, 5ꢁ4 °F) added value indicated aboveꢁ
*2ꢁ Maximum range: Absolute value of 0ꢂ or 100ꢂ of the input range, whichever is greaterꢁ
R8-TC2 SPECIFICATIONS
ES-9788 Rev.5 Page 4/7
http://www.m-system.co.jp/
MODEL: R8-TC2
EXTERNAL VIEW
■ LEFT VIEW
■ FRONT VIEW
■ RIGHT VIEW
SW3
2 1
On
Function Setting
DIP SW
Universal Input
Connector
Status Indicator LED
Indicator LEDs
RUN
21
1
2
3
4
5
6
7
8
9
SW1
SW2
SW3
On
10
11
12
13
14
15
16
8
7
6
5
4
3
2
1
PV1
CT Input Connectors
On
CT1
CT2
MV1
Internal Bus Connectors
Control Output
Connectors
Internal Bus
Connectors
12
SW4
On
Universal Input
Connector
PV2
MV2
1 2
On
SW4
OPERATING MODE SETTING
(*) Factory default
■ Input Selection
Be sure to set unused SW 2-1 through 2-5 and 2-7, 2-8 to
OFF
UNIVERSAL INPUT1 UNIVERSAL INPUT2
INPUT
SW3
SW4
■ Module Address
1
2
1
2
SW 1-1 through 1-4 determine the tenth place digit, while
SW 1-5 through 1-8 do the ones place digit of the address.
Address is selected between 0 to 24.
DC Current
DC Voltage (V)*1
DC Voltage (mV)*2
Potentiometer
Resistor
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
(Factory setting: 0)
SW1
OFF
OFF
ON
OFF
OFF
ON
MODULE
x10
x1
1
5
2
6
3
7
4
8
ADDRESS
T/C
0
1
2
3
4
5
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
ON
RTD
OFF
OFF
*1. Input range:-10 – +10V DC
*2. Input range:-1000 – +1000mV DC
ON
OFF
OFF
OFF
ON
ON
6
7
8
9
OFF
OFF
ON
ON
ON
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
■ Terminator DIP SW
TERMINATOR SW
Without (*)
SW2-6
OFF
ON
With
R8-TC2 SPECIFICATIONS
ES-9788 Rev.5 Page 5/7
http://www.m-system.co.jp/
MODEL: R8-TC2
EXTERNAL DIMENSIONS unit: mm (inch)
[
(
59 2.32
)]
(
24 .94
)
[ ( )]
4 .16
[ ( )]
3 .12
(
55 2.17
)
(
)
DIN RAIL 35 mm wide
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
INPUT
STATUS
LEDs
STATUS
INDICATOR
LED
*1
Power
Circuit
INTERNAL POWER
INTERNAL BUS
INPUT CONNECTOR 1
CJC
Sensor
1
2
3
4
Comm.
Circuit
SW3
Input
Logic A/D
Converter
Pv1
UNIVERSAL INPUT 1
Isolation
Isolation
*2
EXC. SUPPLY
OUTPUT CONNECTOR 1
INPUT CONNECTOR 2
1
2
3
4
1
2
3
4
Input
Logic A/D
Converter
Mv1
Pv2
UNIVERSAL INPUT 2
Output
circuit
CONTROL OUTPUT
SW4
Isolation
CJC
Sensor
Control
Circuit
OUTPUT CONNECTOR 2
INPUT CONNECTOR 3
1
2
3
4
1
2
3
4
Mv2
Output
circuit
CT1
CONTROL OUTPUT
Isolation
Input
Logic A/D
Converter
INPUT CONNECTOR 4
1
2
3
4
CT2
DIP SW
.
*1 The power supply for control circuit, which is non-isolated from internal power.
.
*2 The power supply for output 1 and output 2, which is isolated from the Exc. supply and the internal power.
R8-TC2 SPECIFICATIONS
ES-9788 Rev.5 Page 6/7
http://www.m-system.co.jp/
MODEL: R8-TC2
■ UNIVERSAL INPUT (Pv1, Pv2) CONNECTION e.g.
•RTD/Resistor (3-wire)
•RTD/Resistor (2-wire)
NC
1
2
3
4
NC
1
2
3
4
A
B
B
A
B
NC
•Potentiometer
•Thermocouple
comp. leadwire
1
2
3
4
1
2
3
4
NC
NC
+
T/C
max.
min.
-
−
+
NC
•DC Voltage (-10 – +10V DC)
•DC Current (0 – 20mA DC)
•DC Voltage (-1000 – +1000mV DC)
+
−
1
2
3
4
1
2
3
4
NC
INPUT
−
NC
+
NC
NC
INPUT
■ CT INPUT (CT1, CT2) CONNECTION e.g. ■ CONTROL OUTPUT (Mv1, Mv2) CONNECTION e.g.
•Clamp-on current Sensor
SOURCE
+
1
2
3
4
k
1
2
3
4
NC
NC
−
CT
CONTROL OUTPUT
NC
NC
l
LOAD
Specifications are subject to change without notice.
R8-TC2 SPECIFICATIONS
ES-9788 Rev.5 Page 7/7
http://www.m-system.co.jp/
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明