SC110-10-R/600 [MSYSTEM]
Single Loop Controller Series MULTI-FUNCTION PID CONTROLLER;
| 型号： | SC110-10-R/600 |
| 厂家： | 
M-SYSTEM |
| 描述： | Single Loop Controller Series MULTI-FUNCTION PID CONTROLLER |
| 文件： | 总12页 (文件大小：437K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: SC110
blank: Single supply
Single Loop Controller Series
/M2: 100 – 240 V AC (dual supply)
(Operational voltage range 85 – 264 V AC; 50/60 Hz)
/R: 24 V DC (dual supply)
MULTI-FUNCTION PID CONTROLLER
(color LCD with touch-panel, MV output backup)
(Operational voltage range 24 V DC ±10 %;
ripple 10 %p-p max.)
Control/Backup modules are powered from common terminals
with 'single' supply type; powered from independent
terminals with 'dual' supply type.
Language
blank: Japanese
144
(5.67)
/E: English
(Language (Japanese or English) can be chosen by front
panel setting.)
*
mm (inch)
Configurator Interface
*Selectable with option code
blank: Infrared
/1: Stereo jack
(If external noise interference is a concern, stereo jack
type is recommended.)
MODEL: SC110–[1]0–[2][3]
Terminal block
ORDERING INFORMATION
• Code number: SC110-[1]0-[2][3]
Specify a code from below for each of [1] through [3].
(e.g. SC110-10-M2/3/M2/E/1/T/Q)
blank: One block terminal
/T: Separable terminal
Other Options
blank: none
• Specify the specification for option code /Q
(e.g. /C01/S01)
/Q: Option other than the above (specify the specification)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
[1] DISCRETE OUTPUT
1: Relay contact
2: Photo MOSFET relay
/C02: Polyurethane coating
/C03: Rubber coating
TERMINAL SCREW MATERIAL
/S01: Stainless steel
MODBUS
0:None
FUNCTIONS & FEATURES
Functions & Features
[2] POWER INPUT
AC Power
• Color LCD with touch panel
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V, 50/60 Hz)
• Five Operation views (digital display, bargraph, dual-loop
bargraph, short trend and user's parameter table views)
• Enhanced screen functions for engineering (configuration,
programming and tuning views)
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
• Universal input x 2 points, analog input x 4 points,
discrete input x 6 points, pulse input x 5 points, high speed
pulse input x 1 point
[3] OPTIONS (multiple selections)
Housing Depth (must be specified)
/300: 300 mm (Discontinued, select /3)
/400: 400 mm (Discontinued, select /4)
/600: 600 mm (Discontinued, select /6)
/3: 300 mm
• Current output (4-20 mA) x 2 points, voltage output (1-5
V) x 2 points, relay or photo-MOSFET relay output x 5 points
• RUN contact output (relay) x 1 point
• Computation cycle selectable between 50 msec. and 3
sec. (control cycle selectable between 1 and 64 times of the
computation cycle)
/4: 400 mm
/6: 600 mm
Backup Module Power Supply
• Two PID function blocks
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 1/12
http://www.m-system.co.jp/
MODEL: SC110
• Advanced computation and sequence control functions
• Auto-tuning function
Screw terminal
Terminal screws: Nickel-plated steel (standard) or stainless
steel
• Parameter input and changing with touch panel
• Function parameter setting, list printing and data
downloading/uploading available with Loop Configuration
Builder Software (model: SFEW3E)
Terminal fixing screws: Chrome-plated steel
Housing material: Flame-resistant resin (gray), steel
Isolation: Pv1 to Pv2 to supply output to Ai1 or Ai2 or Ai3 or
Ai4 to Di1 or Di2 or Di3 or Di4 or Di5 or Pi1 or Pi2 or Pi3 or
Pi4 or Pi5 to Di6 or Pi6 to Mv1 to Mv2 or Mv2B to Ao1 or Ao2
to Do1 to Do2 to Do3 to Do4 to Do5 to Do6 to power to
backup module power to FG
• Display parameter setting, saving and transfer with PC
Configurator Software (model: SCCFG)
• Backup module (applicable to Mv2 only) is incorporated
for manual loading: MV output is automatically switched to
manual control in case of control module abnormality
• Independent power supply usable for the manual loader
• Control module can be extracted at the front for
replacement while MV output is maintained
PID control: Single loop, cascade, advanced
Proportional band (P): 1 to 1000 %
Integral time (I): 0.01 to 100 minutes
Derivative time (D): 0.01 to 10 minutes
• Selectable housing depth for ease of using existing wires
in replacement: 300 mm, 400 mm and 600 mm
• Separable terminal block
Auto-tuning: Limit cycle method
Alarm: PV high & low, deviation, rate of change
Computation: 48 functions blocks available for arithmetic
operations, time functions, signal selection, limit, alarm and
other functions
Typical Applications
• Replacement of conventional controllers
• Panel operation for small-scale instrumentation
Sequence operation: Logic sequence and step sequence
(max. 1068 commands)
Computation cycle: 50 msec. to 3 sec. (control cycle
selectable among 1, 2, 4, 8, 16, 32 and 64 times of the
computation cycle)
RELATED PRODUCTS
• PC Configurator cable (model: COP-US)
• Loop configuration builder software (model: SFEW3E Ver.
1.40 or later)
MV output range: -15 - +115 %
Parameter setting: With touch panel or PC (Loop
Configuration Builder Software model: SFEW3E)
Self diagnostics: CPU monitoring with a watchdog timer
RUN contact: OFF in error detected by diagnostic
Infrared communication: Transmission distance max. 0.2
meter (for use with the COP-IRDA)
• Infrared communication adaptor (model: COP-IRDA)
• PC configurator software (model: SCCFG Ver.1.50 or later)
Builder software and configurator software are
downloadable at M-System’s web site.
ACCESSORIES
■ Display
• Precision resistor module (model: REM4): 2
Display device: 4.3-inch TFT LCD
• Cold junction sensor: 2
Display colors: 256
• Mounting brackets: 2
Resolution: 480 × 272 pixels
• Connector adapter: 1
Pixel pitch: 0.198 × 0.198 mm (128 × 128 DPI)
Backlight: LED
(included in Stereo jack type. The jack on the unit and the
plug of PC Configurator cable (not included in the product)
are different in size.)
Backlight life: Approx. 50 000 hours (at 50 % brightness)
Note: The backlight can be replaced in M-System factory.
The LCD must be replaced at the same time.
Screen saver standby time: 1 to 99 minutes
Scaling range: -32000 to +32000
GENERAL SPECIFICATIONS
Construction: Panel flush mounting
Decimal point position: 10-1, 10-2, 10-3, 10-4, 10-5 or none
Scale divisions: 2 to 10
Degree of protection: IP55; ensured for the front panel of
the unit independently mounted to a panel
Connection
Engineering unit indication: Max. 8 characters
Auto/Man indicator: Green/Amber LED
Backup mode MV output setting indicator: Blue LED
MV output setting indicator: Blue LED
Terminal screws: M3.5 screw terminals (torque 1.0 N·m)
Terminal fixing screws: M4 screw terminals
(torque 1.2 N·m)
Backup module power supply terminal (option /M2, /R):
Euro terminal block (applicable wire size: dia. 2.4 max.,
0.5 – 2.5 mm , stripped length 10 mm)
2
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 2/12
http://www.m-system.co.jp/
MODEL: SC110
Burnout indication: 115 % of the measuring range (upscale)
Sensing current: ≤ 1 mA
FACTORY DEFAULT
■ LOOP 1
∙Potentiometer input: Total resistance 100 Ω to 10 kΩ
Minimum span: 50 % of total resistance
Excitation: ≤ 0.6 V DC
P : 100%
I : No integral action
D : No derivative action
CAS
H
L
PID
G02
■ Ai1, Ai2, Ai3, Ai4
∙Voltage input: 1 – 5 V DC
SEQ
G81
Reverse Action
Ai 1
Pv 1
Mv 1
Input resistance: ≥ 1 MΩ
(PV /MV
)
1
1
*
*
1 – 5 V DC
■ Pi1, Pi2, Pi3, Pi4, Pi5: Dry contact
(Di1 through Di5 are assigned to the same terminals
respectively.)
1 – 5 V DC
4 – 20 mA DC
AL1
AL2
Maximum frequency: 20 Hz
■ LOOP 2
Minimum pulse width: 25 msec.
Common: Negative common per 5 points
Sensing: Approx. 12 V DC, 6 mA
ON voltage/resistance: ≤ 2.25 V, ≤ 1.5 kΩ
OFF voltage/resistance: ≥ 11.25 V ≥ 15 kΩ
■ Pi6: Dry contact
P : 100%
: No integral action
D : No derivative action
I
CAS
H
L
PID
G03
SEQ
G81
Reverse Action
Ai 2
Pv 2
Mv 2
(PV /MV
)
(Di6 is assigned to the same terminal.)
Maximum frequency: 10 kHz
1
1
*
*
1 – 5 V DC
1 – 5 V DC
4 – 20 mA DC
AL3
AL4
Minimum pulse width: 0.05 msec.
Common: Negative common
*1. Factory default setting
Use Loop Configuration Builder Software (model: SFEW3E)
to modify setting.
Sensing: Approx. 12 V DC, 12 mA
ON voltage/resistance: ≤ 2 V, ≤ 1.5 kΩ
OFF voltage/resistance: ≥ 11 V, ≥ 15 kΩ
Excitation: 12 V DC ±10%, 15 mA
Current limiting circuit: Approx. 30 mA
■ Di1, Di2, Di3, Di4, Di5: Dry contact
(Pi1 through Pi5 are assigned to the same terminals
respectively.)
SUPPLY OUTPUT
Output voltage:
24 V DC ±10 % with no load
18 V DC min. at 20 mA
Current rating: ≤ 22 mA DC
∙Shortcircuit protection
Current limited: Approx. 30 mA
Common: Negative common per 5 points
Sensing: Approx. 12 V DC, 6 mA
ON voltage/resistance: ≤ 2.25 V, ≤ 1.5 kΩ
OFF voltage/resistance: ≥ 11.25 V ≥ 15 kΩ
■ Di6: Dry contact
INPUT SPECIFICATIONS
■ Pv1, Pv2 (universal input)
(Pi6 is assigned to the same terminal.)
Common: Negative common
∙Current input: 4 – 20 mA DC with input resistance 250 Ω
(REM4)
Sensing: Approx. 12 V DC, 12 mA
ON voltage/resistance: ≤ 2 V, ≤ 1.5 kΩ
OFF voltage/resistance: ≥ 11 V, ≥ 15 kΩ
∙Voltage input: -10 – +10 V DC
-1 – +1 V DC
0 – 10 V DC
1 – 5 V DC
0 – 1 V DC
Input resistance: ≥ 1 MΩ
∙Thermocouple input: K, E, J, T, B, R, S, C, N, U, L, P, PR (See
Table 1)
Input resistance: ≥ 30 kΩ
Burnout sensing: ≤ 0.3 µA
Burnout indication: 115 % of the measuring range (upscale)
∙RTD input: Pt100 (JIS ’97, IEC), Pt100 (JIS ’89), JPt100 (JIS
’89), Pt50Ω (JIS ’81), Ni100 (See Table 2)
Maximum lead wire resistance: 100 Ω per wire
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 3/12
http://www.m-system.co.jp/
MODEL: SC110
[Table 1 (Thermocouple input)]
INSTALLATION
Power input
USABLE
RANGE (°C)
CONFORMANCE
RANGE (°C)
T/C
∙AC:
K (CA)
-272 to +1472
-272 to +1100
-260 to +1300
-272 to +500
24 to 1920
-150 to +1370
-170 to +1000
-180 to +1200
-170 to +400
1000 to 1760
380 to 1760
400 to 1760
100 to 2315
-130 to +1300
-200 to +600
-200 to +900
0 to 1395
Control module
E (CRC)
≤ 25 VA at 100 V AC
≤ 40 VA at 240 V AC
Backup module
J (IC)
T (CC)
B (RH)
≤ 10 VA at 100 V AC
≤ 15 VA at 240 V AC
•DC
R
-100 to +1860
-100 to +1860
-52 to +2416
-272 to +1400
-252 to +700
-252 to +1000
-52 to +1496
-52 to +1860
S
C (WRe 5-26)
Control module: ≤ 650 mA
Backup module: ≤ 150 mA
N
U
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 5 to 90 %RH (non-condensing)
Mounting: Panel flush mounting (high-density mounting in
horizontal direction)
L
P (Platinel II)
(PR)
300 to 1760
Overrange input (out of the usable range) is handled as burnout.
Weight:
[Table 2 (RTD input)]
Approx. 2.0 kg (4.41 lb) for 300 mm depth type
Approx. 2.5 kg (5.51 lb) for 400 mm depth type
Approx. 3.0 kg (6.61 lb) for 600 mm depth type
USABLE
RANGE (°C)
CONFORMANCE
RANGE (°C)
RTD
Pt 100 (JIS ’97, IEC
Pt 100 (JIS ’89)
JPt 100 (JIS ’89)
Pt 50Ω (JIS ’81)
Ni 100
)
-240 to +900
-240 to +900
-236 to +560
-236 to +700
-100 to +252
-200 to +850
-200 to +660
-200 to +510
-200 to +649
-80 to +250
PERFORMANCE
Accuracy
DC input: ±0.1 % ±1 digit
Overrange input (out of the usable range) is handled as burnout.
Thermocouple input: ±1℃ ±1 digit
±2℃ ±1 digit for B, R, S, C and PR
RTD input: ±1℃ ±1 digit
OUTPUT SPECIFICATIONS
■ Mv1, Mv2, Mv2B
Potentiometer input: ±0.2 % ±1 digit
DC output: ±0.1 %
∙Current output: 4 – 20 mA DC
Load resistance: ≤ 600 Ω
Precision resistor module (REM4): ±0.1 %
Cold junction compensation:
(Mv2B is the output from backup unit.)
■ Ao1, Ao2
±2°C at 25°C ±10°C
±4°C for S, R and PR
∙Voltage output: 1 – 5 V DC
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
DC input: ±0.015 %/°C (±0.008 %/°F)
Thermocouple input: ±0.015 %/°C (±0.008 %/°F)
RTD input: ±0.015 %/°C (±0.008 %/°F)
Potentiometer input: ±0.015 %/°C (±0.008 %/°F)
DC output: ±0.015 %/°C (±0.008 %/°F)
Precision resistor module (REM4): ±0.015 %/°C (±0.008
%/°F)
Load resistance: ≥ 10 kΩ
■ Discrete Output
∙Do1, Do2, Do3, Do4, Do5, RUN contact (Do6): Relay
contact
Rated load: 250 V AC @1 A (cos ø = 1)
30 V DC @1 A (resistive load)
Maximum switching voltage: 250 V AC or 30 V DC
Maximum switching power: 250 VA or 60 W
Minimum load: 5 V DC @10 mA
Line voltage effect: ±0.1 % over voltage range
Calendar clock accuracy: Monthly deviation 3 minutes at
25°C
Mechanical life: 2 × 10 cycles
7
∙Do1, Do2, Do3, Do4, Do5: Photo MOSFET relay
Rating: 200 V AC/DC @0.5 A (resistive load)
ON resistance: 2.1 Ω
RAM memory duration in power failure for hot start:
10 minutes assured
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength:
Maximum frequency: 4 Hz @24 V, 10 mA
ON delay time: ≤ 5.0 msec.
1500 V AC @ 1 minute
OFF delay time: ≤ 3.0 msec.
(Pv1 or supply output to Pv2 or Ai1 or Ai2 or Ai3 or Ai4 to
Di1 or Di2 or Di3 or Di4 or Di5 or Pi1 or Pi2 or Pi3 or Pi4 or
Pi5 to Di6 or Pi6 to Mv1 to Mv2 or Mv2B or Ao1 or Ao2 to
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 4/12
http://www.m-system.co.jp/
MODEL: SC110
Do1 to Do2 or Do3 or Do4 or Do5 or Do6 to power to backup
module power to FG)
500 V AC @ 1 minute (Pv2 to Ai1 or Ai2 or Ai3 or Ai4)
500 V AC @ 1 minute (Mv2 or Mv2B to Ao1 or Ao2)
500 V AC @ 1 minute (Do2 to Do3 to Do4 to Do5 to Do6)
500 V AC @ 1 minute (Pv1 to supply output)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1
Measurement Category II (contact output)
Installation Category II (power)
Pollution degree 2
Input or output to contact output – Basic insulation (300
V)
Input or output to power - Reinforced insulation (300 V)
RoHS Directive
EN 50581
Protection against access to the terminal blocks:
Finger protection (VDE 0660-514)
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 5/12
http://www.m-system.co.jp/
MODEL: SC110
EXTERNAL VIEW
■ CONTROL MODULE FRONT VIEW
• Infrared communication type
• Stereo jack type
1
1
2
2
8
Auto/Man
Auto/Man
3
4
6
7
5
7
4
5
6
1. TFT Color LCD with touch panel
Provides operation and engineering views to facilitate monitoring and setting
2. MV output setting indicator LEDs for the backup mode
3. Infrared communication port
Used to communicate with PC via IRDA Communication Adaptor (model: COP-IRDA) to program and change parameters
using Loop Configuration Builder Software (model: SFEW3E) or PC Configurator Software (model: SCCFG)
4. MV value (DOWN) button
5. Acceleration button
(Accelerates MV signal’s changing speed by pressing simultaneously with MV value button)
6. MV value (UP) button
7. Auto / Man selector (changes the control mode for MV output)
8. Configurator jack and cap
Connects with a PC where Loop Configuration Builder Software (model: SFEW3E) or PC configurator software (model: SCCFG)
is installed via a PC configurator cable (model: COP-US) and enables programming and parameter setting
■ BACKUP MODULE
9
10
11
12
13
9. MV output setting indicators
10. Configurator jack
11. MV value (UP) button
12. Acceleration button
(Accelerates MV signal’s changing speed by pressing simultaneously with MV value button)
13. MV value (DOWN) button
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 6/12
http://www.m-system.co.jp/
MODEL: SC110
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
■ INFRARED COMMUNICATION TYPE
1
*
BACKUP MODULE POWER INPUT TERMINAL
175 (6.89)
210 (8.27) max.
• ONE BLOCK TERMINAL
(without option /T)
MOUNTING BRACKETS
TERMINAL COVER
80 (3.15)
52–M3.5 SCREW
60 61 62 63
14
40
41
42
43
44
45
46
47
48
49
50
51
52
1
27
28
29
30
31
32
33
34
35
36
37
38
39
15
2
16
3
17
4
18
5
19
6
20
7
21
8
22
9
23
10
24
11
25
12
26
13
72 (2.83)
24
*2
67.5 (2.66)
(.94)
• SEPARABLE TERMINAL
(with option /T)
*1. Option /M2, /R only *2. Option /3: 300 mm (11.81”)
Option /4: 400 mm (15.75”)
Option /6: 600 mm (23.62”)
52–M3.5 SCREW
4–M4 SCREW FOR
FIXING TERMINAL
14
1
40
41
42
43
44
45
46
47
48
49
50
51
52
27
28
29
30
31
32
33
34
35
36
37
38
39
15
2
16
3
17
4
18
5
19
6
20
7
21
8
22
9
23
10
24
11
25
12
26
13
67.5 (2.66)
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 7/12
http://www.m-system.co.jp/
MODEL: SC110
■ STEREO JACK TYPE
1
*
BACKUP MODULE POWER INPUT TERMINAL
175 (6.89)
210 (8.27) max.
• ONE BLOCK TERMINAL
(without option /T)
MOUNTING BRACKETS
TERMINAL COVER
80 (3.15)
52–M3.5 SCREW
60 61 62 63
14
15
16
17
18
19
20
21
22
23
24
25
26
40
41
42
43
44
45
46
47
48
49
50
51
52
1
27
28
29
30
31
32
33
34
35
36
37
38
39
2
3
4
5
6
7
8
9
10
11
12
13
Jack cap
72 (2.83)
24
*2
1 (.04)
67.5 (2.66)
(.94)
• SEPARABLE TERMINAL
(with option /T)
*1. Option /M2, /R only *2. Option /3: 300 mm (11.81”)
Option /4: 400 mm (15.75”)
Option /6: 600 mm (23.62”)
52–M3.5 SCREW
4–M4 SCREW FOR
FIXING TERMINAL
14
1
40
41
42
43
44
45
46
47
48
49
50
51
52
27
28
29
30
31
32
33
34
35
36
37
38
39
15
2
16
3
17
4
18
5
19
6
20
7
21
8
22
9
23
10
24
11
25
12
26
13
67.5 (2.66)
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 8/12
http://www.m-system.co.jp/
MODEL: SC110
MOUNTING REQUIREMENTS unit: mm
■ PANEL CUTOUT unit: mm
• Single mounting
• Clustered mounting
[68+72×(n - 1)] +1
68 +0.7
0
0
n = number of units
Panel thickness 2.3 – 20
■ Caution
• IP55 is ensured for the front panel of the unit mounted independently to according to a panel. Test the sealing at the
mounting surface once the device is installed.
• Set the unit on a vertical surface with its operation buttons at the lower side. Mounting in other directions may cause heat
built up inside the unit and shorten its life span or degrade its performance.
• Ensure that there is sufficient space for ventilation inside a panel. Do not install above the devices that generate high heat
such as heaters, transformers or resistors. Leave at least 30 mm (1.2 inch) space above, below and behind the unit for
maintenance purpose (e.g. wiring, removing or installing).
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 9/12
http://www.m-system.co.jp/
MODEL: SC110
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Note: In order to improve EMC performance, bond the FG terminal to ground.
Caution: FG terminal is NOT a protective conductor terminal.
■ BACKUP MODULE POWER SUPPLY: SINGLE SUPPLY
Backup Module
Control Module
Isolation
+
+
+
+
34
35
36
37
16
17
18
19
20
21
22
23
24
25
10
11
3
Discrete
Input
Circuit
Di 1 / Pi 1
Di 2 / Pi 2
Di 3 / Pi 3
Di 4 / Pi 4
Di 5 / Pi 5
Do 1
Do 2
Do 3
Do 4
+
–
38
39
Isolation
Sensor
Excitation
SENSOR EXC
31
Do 5
Do 6
Di 6 / Pi 6
Digital
Input
Circuit
Computation
INPUT
COM
32
33
RUN CONTACT
Isolation
Isolation
Isolation
Isolation
Isolation
Isolation
Output
Driver
A1 42
B1 43
C1 44
A2 45
B2 46
C2 47
+
–
+
–
+
A/D
Converter
Mv 1
Pv 1
UNIVERSAL INPUT
4
Output
Driver
5
1
*
Mv 2, Mv 2B
6
A/D
Converter
Pv 2
UNIVERSAL INPUT
Output
Driver
7
Ao 1
Ao 2
Output
Driver
+
+
+
+
–
48
49
50
8
9
A/D
Converter
Ai 1
Ai 2
Ai 3
Ai 4
12 U(+)
POWER
13 V(–)
+
–
51
52
26 FG
40
Isolation
27
Excitation
Supply
+
–
29
30
2-WIRE TRANSMITTER
28
41
PC CONFIGURATOR/
BUILDER SOFTWARE
Infrared Port / Jack
1
Display /
Setting
14
15
2
MV SETTING
INDICATORS
Isolation
Digital
Computation
Output
Driver
Output
Switch
OPERATION BUTTONS
Backup Module
Power Circuit
*1. Backup is applicable to Mv 2 only. Mv 2B is output of the backup module.
■ DISCRETE INPUT PULSE
INPUT CONNECTION E.G.:
+12V
■ UNIVERSAL INPUT CONNECTION E.G.
POTENTIOMETER
max.
RTD
A
B
B
3
2
1
+
+
–
+
–
A
A
B
A
B
C
A
B
C
29
30
A
Dry contact
2-Wire
XMTR
1 or 2kΩ
T/C
*2
+
–
+
–
+
B
C
VOLT / CURRENT
INPUT
R
–
–
C
min.
CJC SENSOR
B
*3
*4
R
*2. Connect input resistor module (model: REM4) for current input.
*3. Connect CJC sensor for thermocouple input.
C
*4. Connect input resistor module (model: REM4).
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 10/12
http://www.m-system.co.jp/
MODEL: SC110
■ BACKUP MODULE POWER SUPPLY: DUAL SUPPLY
Backup Module
Control Module
Isolation
+
+
+
+
34
35
36
37
16
17
18
19
20
21
22
23
24
25
10
11
3
Discrete
Input
Circuit
Di 1 / Pi 1
Di 2 / Pi 2
Di 3 / Pi 3
Di 4 / Pi 4
Di 5 / Pi 5
Do 1
Do 2
Do 3
Do 4
Do 5
+
–
38
39
Isolation
Sensor
Excitation
SENSOR EXC
31
Di 6 / Pi 6
Digital
Input
Circuit
Computation
INPUT
COM
32
33
Do 6
RUN CONTACT
Isolation
Isolation
Isolation
Isolation
Isolation
Isolation
Output
Driver
A1 42
B1 43
C1 44
A2 45
B2 46
C2 47
+
–
+
–
+
A/D
Converter
Mv 1
Pv 1
UNIVERSAL INPUT
4
Output
Driver
5
1
*
Mv 2, Mv 2B
6
A/D
Converter
Pv 2
UNIVERSAL INPUT
Output
Driver
7
Ao 1
Ao 2
Output
Driver
+
+
+
+
–
48
49
50
8
9
A/D
Converter
Ai 1
Ai 2
Ai 3
Ai 4
12 U(+)
POWER
13 V(–)
+
–
51
52
26 FG
40
Isolation
27
Excitation
Supply
+
–
29
30
2-WIRE TRANSMITTER
28
41
PC CONFIGURATOR/
BUILDER SOFTWARE
Infrared Port / Jack
1
Display /
Setting
14
15
2
MV SETTING
INDICATORS
Isolation
62
Digital
Computation
Output
Driver
Output
Switch
63 FG
60 U(+)
61 V(–)
OPERATION BUTTONS
Backup Module
Power Circuit
BACK UP POWER
*1. Backup is applicable to Mv 2 only. Mv 2B is output of the backup module.
■ UNIVERSAL INPUT CONNECTION E.G.
■ DISCRETE INPUT PULSE
INPUT CONNECTION E.G.:
+12V
POTENTIOMETER
max.
RTD
A
B
B
3
2
1
+
+
–
+
–
A
B
C
A
B
A
B
C
A
B
C
29
30
A
Dry contact
1 or 2kΩ
2-Wire
XMTR
T/C
+
*2
+
–
+
VOLT / CURRENT
INPUT
R
–
–
–
C
min.
CJC SENSOR
B
*3
*4
R
*2. Connect input resistor module (model: REM4) for current input.
*3. Connect CJC sensor for thermocouple input.
C
*4. Connect input resistor module (model: REM4).
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 11/12
http://www.m-system.co.jp/
MODEL: SC110
SYSTEM CONFIGURATION EXAMPLES
■ SINGLE LOOP CONTROL
■ CASCADE CONTROL
Multi-Function PID Controller
Model: SC110
Multi-Function PID Controller
Model: SC110
Ai
PV
PV
MV
MV
Flow
Level
Specifications are subject to change without notice.
SC110 SPECIFICATIONS
ES-6339 Rev.17 Page 12/12
http://www.m-system.co.jp/
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明