SC200W-12-M2/3 [MSYSTEM]

Single Loop Controller Series MULTI-FUNCTION PID CONTROLLER;


型号：	SC200W-12-M2/3
厂家：	M-SYSTEM
描述：	Single Loop Controller Series MULTI-FUNCTION PID CONTROLLER
文件：	总10页 (文件大小：436K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: SC200W

/E: English

Single Loop Controller Series

(Language (Japanese or English) can be chosen by front

panel setting.)

MULTI-FUNCTION PID CONTROLLER

(color LCD with touch-panel, Modbus/NestBus

communication, expansion module function)

Configurator Interface (must be specified)

/1: Stereo jack

Terminal block (must be specified)

/T: Separable terminal

Other Options

blank: none

/Q: Option other than the above (specify the specification)

144

(5.67)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

mm (inch)

/C02: Polyurethane coating

/C03: Rubber coating

*Selectable with option code

TERMINAL SCREW MATERIAL

/S01: Stainless steel

MODEL: SC200W–[1][2]–[3][4]

FUNCTIONS & FEATURES

ORDERING INFORMATION

• Code number: SC200W-[1][2]-[3][4]

Specify a code from below for each of [1] through [4].

(e.g. SC200W-11-M2/3/E/1/T/Q)

Functions & Features

• Color LCD with touch panel

• Five Operation views (digital display, bargraph, dual-loop

bargraph, short trend and user's parameter table views)

• Enhanced screen functions for engineering (configuration,

programming and tuning views)

• Specify the specification for option code /Q

(e.g. /C01/S01)

• Universal input x 2 points, analog input x 4 points,

discrete input x 6 points, pulse input x 5 points, high speed

pulse input x 1 point

[1] DISCRETE OUTPUT

1: Relay contact

• Current output (4-20 mA) x 2 points, voltage output (1-5

V) x 2 points, relay or photo-MOSFET relay output x 5 points

• RUN contact output (relay) x 1 point

2: Photo MOSFET relay

[2] MODBUS

1: Modbus-RTU

2: Modbus/TCP

• I/O signals can be added with remote I/O modules

connected via NestBus peer-to-peer communication

• Computation cycle selectable between 100 msec. and 3

sec. (control cycle selectable between 1 and 64 times of the

computation cycle)

[3] POWER INPUT

AC Power

• Two PID function blocks

• Advanced computation and sequence control functions

• Auto-tuning function

M2: 100 – 240 V AC (Operational voltage range 85 – 264 V, 50/60 Hz)

DC Power

• Parameter input and changing with touch panel

• Function parameter setting, list printing and data

downloading/uploading available with Loop Configuration

Builder Software (model: SFEW3E)

R: 24 V DC

(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

[4] OPTIONS (multiple selections)

• Short trend export (CSV), display parameter setting,

saving and transfer with PC Configurator Software (model:

SCCFG)

Housing Depth

blank: 250 mm

/3: 300 mm

• Control and supervision by SCADA software via Modbus

TCP/IP or RTU communication

/4: 400 mm

Language

• Selectable housing depth for ease of using existing wires

in replacement: 250 mm, 300 mm and 400 mm

blank: Japanese

SC200W SPECIFICATIONS

ES-6346 Rev.0 Page 1/10

http://www.m-system.co.jp/

MODEL: SC200W

• Separable terminal block

Sequence operation: Logic sequence and step sequence

(max. 1068 commands)

• Expansion of operations blocks due to Expansion module

Computation cycle: 100 msec. to 3 sec. (control cycle

selectable among 1, 2, 4, 8, 16, 32 and 64 times of the

computation cycle)

Typical Applications

• Replacement of conventional controllers

• Panel operation for small-scale instrumentation

MV output range: -15 - +115 %

Parameter setting: With touch panel or PC (Loop

Configuration Builder Software model: SFEW3E)

Self diagnostics: CPU monitoring with a watchdog timer

RUN contact: OFF in error detected by diagnostic (including

NestBus)

RELATED PRODUCTS

• PC Configurator cable (model: COP-US)

• Loop configuration builder software (model: SFEW3E Ver.

1.101 or later)

Short trend

• PC configurator software (model: SCCFG Ver.1.84 or later)

Builder software and configurator software are

downloadable at M-System’s web site.

Storing interval: 1, 2, 5, 10, 20, 30 sec.,

1, 2, 5, 10, 30, 60 min.

Capacity: 400 points (display 200 points)

ACCESSORIES

■ Display

• Precision resistor module (model: REM4): 2 units

• Cold junction compensation sensor: 2 pcs

• Mounting brackets: 2 pcs

Display device: 4.3-inch TFT LCD

Display colors: 256

Resolution: 480 × 272 pixels

• Connector adapter: 1 pce

Pixel pitch: 0.198 × 0.198 mm (128 × 128 DPI)

Backlight: LED

(The jack on the unit and the plug of PC Configurator cable

(not included in the product) are different in size.)

Backlight life: Approx. 50 000 hours (at 50 % brightness)

Note: The backlight can be replaced in M-System factory.

The LCD must be replaced at the same time.

Screen saver standby time: 1 to 99 minutes

Scaling range: -32000 to +32000

GENERAL SPECIFICATIONS

Construction: Panel flush mounting

Degree of protection: IP55; ensured for the front panel of

the unit independently mounted to a panel

Connection

Decimal point position: 10-1, 10-2, 10-3, 10-4, 10-5 or none

Scale divisions: 2 to 10

Engineering unit indication: Max. 8 characters

Auto/Man indicator: Green/Amber LED

Terminal screws: M3.5 screw terminals (torque 1.0 N·m)

Terminal fixing screws: M4 screw terminals

(torque 1.2 N·m)

Ethernet: RJ-45 Modular Jack

Screw terminal

Terminal screws: Nickel-plated steel (standard) or stainless

steel

Terminal fixing screws: Chrome-plated steel

Housing material: Flame-resistant resin (gray), steel

Isolation: Pv1 to Pv2 to supply output to Ai1 or Ai2 or Ai3 or

Ai4 to Di1 or Di2 or Di3 or Di4 or Di5 or Pi1 or Pi2 or Pi3 or

Pi4 or Pi5 to Di6 or Pi6 to Mv1 to Mv2 to Ao1 or Ao2 to Do1

to Do2 to Do3 to Do4 to Do5 to Do6 to NestBus to Modbus-

RTU to Modbus/TCP to power to FG

PID control: Single loop, cascade, advanced

Proportional band (P): 1 to 1000 %

Integral time (I): 0.01 to 100 minutes

Derivative time (D): 0.01 to 10 minutes

Auto-tuning: Limit cycle method

Alarm: PV high & low, deviation, rate of change

Computation: 48 functions blocks available for arithmetic

operations, time functions, signal selection, limit, alarm and

other functions

SC200W SPECIFICATIONS

ES-6346 Rev.0 Page 2/10

http://www.m-system.co.jp/

MODEL: SC200W

Protocol: Modbus/TCP

Data: RTU (binary)

Connections: 2

FACTORY DEFAULT

■ LOOP 1

P : 100%

I : No integral action

D : No derivative action

Transmission media:

CAS

10BASE-T (STP cable, category 5)

100BASE-TX (STP cable, category 5e)

Max. segment length: 100 meters

Port number: 502

PID

G02

SEQ

G81

Reverse Action

Ai 1

Pv 1

Mv 1

(PV /MV

)

1 – 5 V DC

IP address: 192.168.0.1 (factory setting)

1 – 5 V DC

4 – 20 mA DC

AL1

AL2

SUPPLY OUTPUT

Output voltage:

■ LOOP 2

P : 100%

: No integral action

D : No derivative action

24 V DC ±10 % with no load

18 V DC min. at 20 mA

Current rating: ≤ 22 mA DC

∙Shortcircuit protection

Current limited: Approx. 30 mA

CAS

PID

G03

SEQ

G81

Reverse Action

Ai 2

Pv 2

Mv 2

(PV /MV

)

1 – 5 V DC

4 – 20 mA DC

INPUT SPECIFICATIONS

■ Pv1, Pv2 (universal input)

AL3

AL4

∙Current input: 4 – 20 mA DC with input resistance 250 Ω

(REM4)

*1. Factory default setting

Use Loop Configuration Builder Software (model: SFEW3E)

to modify setting.

∙Voltage input: -10 – +10 V DC

-1 – +1 V DC

0 – 10 V DC

EXTERNAL INTERFACE

■ NestBus

1 – 5 V DC

0 – 1 V DC

Configuration: Bus type multi-drop

Standard: Conforms to TIA/EIA-485-A

Transfer rate: 19.2 kbps

Input resistance: ≥ 1 MΩ

∙Thermocouple input: K, E, J, T, B, R, S, C, N, U, L, P, PR (See

Table 1)

Protocol: NestBus (M-System’s own protocol)

Max. transmission distance: 1 kilometer

Transmission media:

Input resistance: ≥ 30 kΩ

Burnout sensing: ≤ 0.3 µA

Burnout indication: 115 % of the measuring range (upscale)

∙RTD input: Pt100 (JIS ’97, IEC), Pt100 (JIS ’89), JPt100 (JIS

’89), Pt50Ω (JIS ’81), Ni100 (See Table 2)

Maximum lead wire resistance: 100 Ω per wire

Burnout indication: 115 % of the measuring range (upscale)

Sensing current: ≤ 1 mA

Shielded twisted-pair cable (CPEV-S 0.9 dia.)

Terminating resistor: incorporated

Card No. setting: 0 - F (16 cards; 2 assigned for one unit)

■ Modbus-RTU

Configuration: Half-duplex, asynchronous, no procedure

Standard: Conforms to TIA/EIA-485-A

Max. transmission distance: 500 meters

Transfer rate: 4800, 9600, 19.2 k, 38.4 k bps

Data bit: 8

∙Potentiometer input: Total resistance 100 Ω to 10 kΩ

Minimum span: 50 % of total resistance

Excitation: ≤ 0.6 V DC

■ Ai1, Ai2, Ai3, Ai4

Parity bit: Odd, even, none

∙Voltage input: 1 – 5 V DC

Max. node number: 15 (except the master)

Transmission media:

Input resistance: ≥ 1 MΩ

■ Pi1, Pi2, Pi3, Pi4, Pi5: Dry contact

(Di1 through Di5 are assigned to the same terminals

respectively.)

Shielded twisted-pair cable (CPEV-S 0.9 dia.)

Terminating resistor: incorporated

Node address setting: 1 - 247

Maximum frequency: 20 Hz

■ Modbus/TCP (Ethernet)

Minimum pulse width: 25 msec.

Common: Negative common per 5 points

Sensing: Approx. 12 V DC, 6 mA

Physical layer standard: IEEE 802.3u

Data link layer: 10BASE-T / 100BASE-TX

Transfer rate: 10 / 100 Mbps, Auto Negotiation

SC200W SPECIFICATIONS

ES-6346 Rev.0 Page 3/10

http://www.m-system.co.jp/

MODEL: SC200W

ON voltage/resistance: ≤ 2.25 V, ≤ 1.5 kΩ

OFF voltage/resistance: ≥ 11.25 V ≥ 15 kΩ

■ Pi6: Dry contact

OUTPUT SPECIFICATIONS

■ Mv1, Mv2

∙Current output: 4 – 20 mA DC

Load resistance: ≤ 600 Ω

(Di6 is assigned to the same terminal.)

Maximum frequency: 10 kHz

■ Ao1, Ao2

Minimum pulse width: 0.05 msec.

Common: Negative common

∙Voltage output: 1 – 5 V DC

Load resistance: ≥ 10 kΩ

Sensing: Approx. 12 V DC, 12 mA

ON voltage/resistance: ≤ 2 V, ≤ 1.5 kΩ

OFF voltage/resistance: ≥ 11 V, ≥ 15 kΩ

Excitation: 12 V DC ±10%, 15 mA

Current limiting circuit: Approx. 30 mA

■ Di1, Di2, Di3, Di4, Di5: Dry contact

(Pi1 through Pi5 are assigned to the same terminals

respectively.)

■ Discrete Output

∙Do1, Do2, Do3, Do4, Do5, RUN contact (Do6): Relay

contact

Rated load: 250 V AC @1 A (cos ø = 1)

30 V DC @1 A (resistive load)

Maximum switching voltage: 250 V AC or 30 V DC

Maximum switching power: 250 VA or 60 W

Minimum load: 5 V DC @10 mA

Common: Negative common per 5 points

Sensing: Approx. 12 V DC, 6 mA

ON voltage/resistance: ≤ 2.25 V, ≤ 1.5 kΩ

OFF voltage/resistance: ≥ 11.25 V ≥ 15 kΩ

■ Di6: Dry contact

Mechanical life: 2 × 10 cycles

∙Do1, Do2, Do3, Do4, Do5: Photo MOSFET relay

Rating: 200 V AC/DC @0.5 A (resistive load)

ON resistance: 2.1 Ω

Maximum frequency: 4 Hz @24 V, 10 mA

ON delay time: ≤ 5.0 msec.

(Pi6 is assigned to the same terminal.)

Common: Negative common

OFF delay time: ≤ 3.0 msec.

Sensing: Approx. 12 V DC, 12 mA

ON voltage/resistance: ≤ 2 V, ≤ 1.5 kΩ

OFF voltage/resistance: ≥ 11 V, ≥ 15 kΩ

[Table 1 (Thermocouple input)]

INSTALLATION

Power input

∙AC:

USABLE

RANGE (°C)

CONFORMANCE

RANGE (°C)

≤ 25 VA at 100 V AC

T/C

K (CA)

≤ 40 VA at 240 V AC

-272 to +1472

-272 to +1100

-260 to +1300

-272 to +500

24 to 1920

-150 to +1370

-170 to +1000

-180 to +1200

-170 to +400

1000 to 1760

380 to 1760

400 to 1760

100 to 2315

-130 to +1300

-200 to +600

-200 to +900

0 to 1395

•DC: ≤ 650 mA

E (CRC)

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 5 to 90 %RH (non-condensing)

Mounting: Panel flush mounting (high-density mounting in

horizontal direction)

J (IC)

T (CC)

B (RH)

-100 to +1860

-52 to +2416

-272 to +1400

-252 to +700

-252 to +1000

-52 to +1496

-52 to +1860

Weight:

Approx. 1.8 kg (3.97 lb) for 250 mm depth type

Approx. 2.0 kg (4.41 lb) for 300 mm depth type

Approx. 2.5 kg (5.51 lb) for 400 mm depth type

C (WRe 5-26)

P (Platinel II)

PERFORMANCE

(PR)

300 to 1760

Accuracy

Overrange input (out of the usable range) is handled as burnout.

DC input: ±0.1 % ±1 digit

Thermocouple input: ±1℃ ±1 digit

±2℃ ±1 digit for B, R, S, C and PR

RTD input: ±1℃ ±1 digit

[Table 2 (RTD input)]

USABLE

RANGE (°C)

CONFORMANCE

RANGE (°C)

RTD

Pt 100 (JIS ’97, IEC

Pt 100 (JIS ’89)

JPt 100 (JIS ’89)

Pt 50Ω (JIS ’81)

Ni 100

)

-240 to +900

-236 to +560

-236 to +700

-100 to +252

-200 to +850

-200 to +660

-200 to +510

-200 to +649

-80 to +250

Potentiometer input: ±0.2 % ±1 digit

DC output: ±0.1 %

Precision resistor module (REM4): ±0.1 %

Cold junction compensation:

±2°C at 25°C ±10°C

Overrange input (out of the usable range) is handled as burnout.

±4°C for S, R and PR

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

SC200W SPECIFICATIONS

ES-6346 Rev.0 Page 4/10

http://www.m-system.co.jp/

MODEL: SC200W

DC input: ±0.015 %/°C (±0.008 %/°F)

Thermocouple input: ±0.015 %/°C (±0.008 %/°F)

RTD input: ±0.015 %/°C (±0.008 %/°F)

Potentiometer input: ±0.015 %/°C (±0.008 %/°F)

DC output: ±0.015 %/°C (±0.008 %/°F)

Precision resistor module (REM4): ±0.015 %/°C (±0.008

%/°F)

Line voltage effect: ±0.1 % over voltage range

Calendar clock accuracy: Monthly deviation 3 minutes at

25°C

RAM memory duration in power failure for hot start:

10 minutes assured

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength:

1500 V AC @ 1 minute

(Pv1 or supply output to Pv2 or Ai1 or Ai2 or Ai3 or Ai4 to

Di1 or Di2 or Di3 or Di4 or Di5 or Pi1 or Pi2 or Pi3 or Pi4 or

Pi5 to Di6 or Pi6 to Mv1 to Mv2 or Ao1 or Ao2 to Do1 to Do2

or Do3 or Do4 or Do5 or Do6 to NestBus to Modbus-RTU to

Modbus/TCP to power to FG)

500 V AC @ 1 minute (Pv2 to Ai1 or Ai2 or Ai3 or Ai4)

500 V AC @ 1 minute (Mv2 to Ao1 or Ao2)

500 V AC @ 1 minute (Do2 to Do3 to Do4 to Do5 to Do6)

500 V AC @ 1 minute (Pv1 to supply output)

EXTERNAL VIEW

Auto/Man

1. TFT Color LCD with touch panel

Provides operation and engineering views to facilitate monitoring and setting

2. Configurator jack and cap

Connects with a PC where Loop Configuration Builder Software (model: SFEW3E) or PC configurator software (model: SCCFG)

is installed via a PC configurator cable (model: COP-US) and enables programming and parameter setting

3. MV value (DOWN) button

4. Acceleration button

(Accelerates MV signal’s changing speed by pressing simultaneously with MV value button)

5. MV value (UP) button

6. Auto / Man selector (changes the control mode for MV output)

SC200W SPECIFICATIONS

ES-6346 Rev.0 Page 5/10

http://www.m-system.co.jp/

MODEL: SC200W

COMMUNICATION CABLE CONNECTIONS

■ NestBus

SML

SC200W

■ Modbus-RTU

R2K-1

RS-485

SC200W

RS-232-C

*1. Internal terminating resistor is used when the device is at the end of a transmission line.

*2. For noise protection, connect all shielded cables with each other and ground them at a single dedicated ground point within

the system with grounding resistance of 100 Ω or less. Note that the most suitable ground point differs depending on the system.

Also note that there may be cases where less noise is caused when the shields are left ungrounded.

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

175 (6.89)

210 (8.27) max.

RJ-45 CONNECTOR

52–M3.5 SCREW

MOUNTING BRACKETS

TERMINAL COVER

4–M4 SCREW FOR

FIXING TERMINAL

Jack cap

72 (2.83)

1 (.04)

67.5 (2.66)

(.94)

*1. For Modbus/TCP only

*2. Standard model: 250 mm (9.84”)

300 mm (11.81”)

400 mm (15.75”)

Option /3:

Option /4:

SC200W SPECIFICATIONS

ES-6346 Rev.0 Page 6/10

http://www.m-system.co.jp/

MODEL: SC200W

MOUNTING REQUIREMENTS unit: mm

■ PANEL CUTOUT unit: mm

• Single mounting

• Clustered mounting

68 ^+0.7

[68+72×(n - 1)] ⁺¹

n = number of units

Panel thickness 2.3 – 20

■ Caution

• IP55 is ensured for the front panel of the unit mounted independently according to a panel. Test the sealing at the mounting

surface once the device is installed.

• Set the unit on a vertical surface with its operation buttons at the lower side. Mounting in other directions may cause heat

built up inside the unit and shorten its life span or degrade its performance.

• Ensure that there is sufficient space for ventilation inside a panel. Do not install above the devices that generate high heat

such as heaters, transformers or resistors. Leave at least 30 mm (1.2 inch) space above, below and behind the unit for

maintenance purpose (e.g. wiring, removing or installing).

SC200W SPECIFICATIONS

ES-6346 Rev.0 Page 7/10

http://www.m-system.co.jp/

MODEL: SC200W

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Isolation

Shielded Twisted-pair Cable

40 T1

27 T2

28 T3

41 T4

26 FG

To Other

NestBus

Devices

Discrete

Input

Circuit

Di 1 / Pi 1

–

Jumper*

Di 2 / Pi 2

Di 3 / Pi 3

Di 4 / Pi 4

Di 5 / Pi 5

SHLD

Isolation

To Other

Modbus-RTU

Devices

–

14 T2

15 T3

Shielded Twisted-pair Cable

Jumper*

Isolation

Sensor

Excitation

SENSOR EXC

Di 6 / Pi 6

RJ-45 CONNECTOR Modbus/TCP

Digital

Input

Circuit

Computation

INPUT

COM

Isolation

Do 1

Isolation

A1 42

B1 43

C1 44

A2 45

B2 46

C2 47

A/D

Converter

Do 2

Pv 1

UNIVERSAL INPUT

Do 3

A/D

Converter

Pv 2

UNIVERSAL INPUT

Do 4

A/D

Converter

Ai 1

Ai 2

Ai 3

Ai 4

Do 5

Do 6

RUN CONTACT

Isolation

Output

Driver

–

Mv 1

Mv 2

Isolation

Output

Driver

Excitation

Supply

–

2-WIRE TRANSMITTER

Output

Driver

PC CONFIGURATOR/

BUILDER SOFTWARE

Ao 1

Ao 2

Jack

Output

Driver

–

Display /

Setting

12 U(+)

13 V(–)

POWER

*1. Close across the terminals 27 – 28 when the unit is located at the end of a transmission line (= no cross-wiring).

*2. Close across the terminals 14 – 15 when the unit is located at the end of a transmission line (= no cross-wiring).

■ UNIVERSAL INPUT CONNECTION E.G.

■ DISCRETE INPUT PULSE

INPUT CONNECTION E.G.:

+12V

POTENTIOMETER

max.

RTD

–

Dry contact

2-Wire

XMTR

T/C

1 or 2kΩ

–

VOLT / CURRENT

INPUT

–

min.

CJC SENSOR

*3. Connect input resistor module (model: REM4) for current input.

*4. Connect CJC sensor for thermocouple input.

*5. Connect input resistor module (model: REM4).

SC200W SPECIFICATIONS

ES-6346 Rev.0 Page 8/10

http://www.m-system.co.jp/

MODEL: SC200W

SYSTEM CONFIGURATION EXAMPLES

■ SINGLE LOOP CONTROL

■ CASCADE CONTROL

Multi-Function PID Controller

Model: SC200W

Multi-Function PID Controller

Model: SC200W

Flow

Level

■ I/O EXPANDED VIA NESTBUS

NestBus

Multi-Function PID Controller

Model: SC200W

Multi-Function PID Controller

Model: SC200

Remote I/O Module

Model: SML

PWR

RUN

■ CONTROL / SUPERVISION VIA MODBUS/TCP

SCADA System

Modbus/TCP

Ethernet Communication Adaptor

Model: GR8-EM

Multi-Function PID Controller

Model: SC200W

Modbus-RTU

Multi-Function PID Controller

Model: SC200W

Multi-Function PID Controller

Model: SC200

SC200W SPECIFICATIONS

ES-6346 Rev.0 Page 9/10

http://www.m-system.co.jp/

MODEL: SC200W

■ CONTROL / SUPERVISION VIA MODBUS-RTU

SCADA System

RS-485/RS-232-C

Converter

Model: R2K-1

Modbus-RTU

Multi-Function PID Controller

Model: SC200W

Multi-Function PID Controller

Model: SC200

Specifications are subject to change without notice.

SC200W SPECIFICATIONS

ES-6346 Rev.0 Page 10/10

http://www.m-system.co.jp/

SC200W-12-M2/3 [MSYSTEM]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E