SES-162-S/E [MSYSTEM]

Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR;


型号：	SES-162-S/E
厂家：	M-SYSTEM
描述：	Plug-in Signal Conditioners M-UNIT HIGH/LOW SELECTOR
文件：	总4页 (文件大小：121K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MODEL: SES

Plug-in Signal Conditioners M-UNIT

[3] OUTPUT

Current

A: 4 – 20 mA DC (Load resistance 750 Ω max.)

B: 2 – 10 mA DC (Load resistance 1500 Ω max.)

C: 1 – 5 mA DC (Load resistance 3000 Ω max.)

D: 0 – 20 mA DC (Load resistance 750 Ω max.)

E: 0 – 16 mA DC (Load resistance 900 Ω max.)

F: 0 – 10 mA DC (Load resistance 1500 Ω max.)

G: 0 – 1 mA DC (Load resistance 15 kΩ max.)

Z: Specify current (See OUTPUT SPECIFICATIONS)

Voltage

HIGH/LOW SELECTOR

(isolated)

Functions & Features

• Monitoring two DC input signals and transmitting an

output signal proportional to the higher or lower input

• LCD meter indicates the selected input signals

(engineering unit display selectable)

• Simple loop test output (0 % and 100 %)

• Isolation up to 2000 V AC

1: 0 – 10 mV DC (Load resistance 10 kΩ min.)

2: 0 – 100 mV DC (Load resistance 100 kΩ min.)

3: 0 – 1 V DC (Load resistance 100 Ω min.)

4: 0 – 10 V DC (Load resistance 1000 Ω min.)

5: 0 – 5 V DC (Load resistance 500 Ω min.)

6: 1 – 5 V DC (Load resistance 500 Ω min.)

4W: -10 – +10 V DC (Load resistance 2000 Ω min.)

5W: -5 – +5 V DC (Load resistance 1000 Ω min.)

0: Specify voltage (See OUTPUT SPECIFICATIONS)

• High-density mounting

Typical Applications

• Selecting greater flow, pressure, etc. for control

• Heating control by multiple T/C’s on a furnace

(1.97)

(3.15)

[4] POWER INPUT

AC Power

B: 100 V AC

127

(5)

C: 110 V AC

mm (inch)

D: 115 V AC

F: 120 V AC

G: 200 V AC

MODEL: SES–[1][2][3]–[4][5]

H: 220 V AC

J: 240 V AC

DC Power

ORDERING INFORMATION

• Code number: SES-[1][2][3]-[4][5]

Specify a code from below for each [1] through [5].

(e.g. SES-1AA-B/E2Q)

S: 12 V DC

R: 24 V DC

V: 48 V DC

P: 110 V DC (Not selectable with Option /E2.)

• Special output range (For codes Z & 0)

• Specify the specification for option code /Q

(e.g. /C01/S01)

[5] OPTIONS (multiple selections)

LCD Meter (after selection)

blank: Without

[1] SELECTING FUNCTION

1: Low input

/E: With (0.0 - 100.0 % display)

/E2: With (in engineering unit with backlight and the

simple loop test output)

2: High input

Other Options

[2] INPUT

Current

blank: none

/Q: Option other than the above (specify the specification)

A: 4 – 20 mA DC (Input resistance 250 Ω)

B: 2 – 10 mA DC (Input resistance 500 Ω)

C: 1 – 5 mA DC (Input resistance 1000 Ω)

H: 10 – 50 mA DC (Input resistance 100 Ω)

Voltage

6: 1 – 5 V DC (Input resistance 1 MΩ min.)

SES SPECIFICATIONS

ES-1646 Rev.3 Page 1/4

http://www.m-system.co.jp/

MODEL: SES

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

INSTALLATION

Power input

•AC: Operational voltage range: rating ±10 %, 50/60 ±2 Hz,

approx. 2 VA

/C02: Polyurethane coating

/C03: Rubber coating

(approx. 3 VA with Option /E2)

TERMINAL SCREW MATERIAL

/S01: Stainless steel

•DC: Operational voltage range: rating ±10 %, or 85 – 150 V

for 110 V rating ripple 10 %p-p max.

approx. 2.5 W (110 mA at 24 V; approx. 3.5 W with Option

/E2)

GENERAL SPECIFICATIONS

Construction: Plug-in

Operating temperature: -5 to +60°C (23 to 140°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Weight: 400 g (0.88 lb)

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Overrange output: Approx. -10 to +120 % at 1 – 5 V

Selecting operation: Automatic

PERFORMANCE in percentage of span

Accuracy: ±0.2 %

Display accuracy: ± (0.2 % of FS + 1 digit)

Simple loop test output setting accuracy: ±0.5 %

Selecting sensitivity: 0.5%

Simple loop test output: 0 % and 100 % signal simulated by

selecting the front switch positions. (Only for option code

/E2)

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: ≤ 0.5 sec. (0 – 90 %)

■ DISPLAY (LCD meter)

• Option code: /E

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

to power to ground)

LCD digital display: 0.0 - 100.0 % (min. digit 0.1 %)

(No scaling)

• Option code: /E2

LCD digital display: Engineering unit

Display scaling: -10000 – +10000

Decimal position: 10-1 - 10-4 or no decimal point

Engineering unit: %, μV, mV, V, mA, A, °C, °F, Ω, DEG K,

mHz, Hz, kHz, VAC, AAC, mg, g, kg, t, rpm or rps selectable

Back light: Green at normal, red at loop test output enable

Factory setting: scaling 0.00 - 100.00, unit: %

INPUT SPECIFICATIONS

■ DC Current:

Shunt resistor attached to the input terminals (0.5 W)

OUTPUT SPECIFICATIONS

■ DC Current: 0 – 20 mA DC

Minimum span: 1 mA

Offset: Max. 1.5 times span

Load resistance: Output drive 15 V max.

■ DC Voltage: -10 – +12 V DC

Minimum span: 5 mV

Offset: Max. 1.5 times span

Load resistance: Output drive 10 mA max.; 5 mA for

negative voltage output; at ≥ 0.5 V

SES SPECIFICATIONS

ES-1646 Rev.3 Page 2/4

http://www.m-system.co.jp/

MODEL: SES

EXTERNAL VIEW

OPTION /E2

LCD Meter

NEXT Key

Loop Test Selector

ENTER Key

Top

: 0% fixed

Middle : 100% fixed

Bottom : Cancel

(normal operating mode)

EXTERNAL DIMENSIONS unit: mm (inch)

CLAMP

(top & bottom)

7.8 (.31)

DIN RAIL

35mm wide

2–4.5 (.18) dia.

MTG HOLE

15 (.59) deep

8–M3.5

SCREW

50 (1.97)

107 (4.21)

127 (5)

40 (1.57)

50 (1.97)

[3.3 (.13)]

• When mounting, no extra space is needed between units.

TERMINAL ASSIGNMENTS unit: mm (inch)

INPUT RESISTOR

(model: REM)

Input shunt resistor attached

for current input.

SES SPECIFICATIONS

ES-1646 Rev.3 Page 3/4

http://www.m-system.co.jp/

MODEL: SES

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

Isolation

Output

Driver

–

Selector

INPUT 1

INPUT 2

OUTPUT

POWER

***

LOOP TEST

SELECTOR

U(+)

V(–)

Base Socket

Input shunt resistor attached for current inputs.

** Option /E, E2

*** Option /E2

Specifications are subject to change without notice.

SES SPECIFICATIONS

ES-1646 Rev.3 Page 4/4

http://www.m-system.co.jp/

相关型号：