TC10EM-V-M2 [MSYSTEM]
Temperature Controller TC10 Series;
| 型号： | TC10EM-V-M2 |
| 厂家： | 
M-SYSTEM |
| 描述： | Temperature Controller TC10 Series |
| 文件： | 总7页 (文件大小：207K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: TC10EM
47 – 66 Hz)
Temperature Controller TC10 Series
RELATED PRODUCTS
TEMPERATURE CONTROLLER
(Modbus, 5 digit, LED display type, size 96 x 96 mm)
Functions & Features
• PC configurator software (model: TC10CFG)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
• Two PID controllers*
• Universal input x 2 points, control output x 4 points,
discrete input x 2 points, clamp-on current sensor input x 2
points
• Clamp-on current sensor (model: CLSE)
(Used for detecting the heater wire break)
• 2 universal inputs configurable to T/C, RTD, DC current or
voltage independently
• Discrete inputs usable to switch PID bank or operation
mode
GENERAL SPECIFICATIONS
Construction: Panel flush mounting
• Control outputs configurable to MV, PV or alarm
• Clamp-on current sensor input enables to detect heater
wire break or over current
Degree of protection: IP65; applicable to the front panel of
the unit with single mounting according to the specified
panel cutout
• Auto tuning function
*Only single loop control is available while loop 1 remote SP
is enabled.
Configuration jack: 2.5 dia. miniature jack connector;
RS-232-C level
Connection: M3 separable screw terminal (torque 0.5 N·m)
Solderless terminal: Refer to the drawing at the end of the
section.
96(3.8)
Recommended manufacturer: Japan Solderless Terminal
MFG.Co.Ltd, Nichifu Co.,ltd
Applicable wire size: 0.25 to 1.65 mm
2
(AWG 22 to 16)
96(3.8)
Screw terminal: Nickel-plated steel
Housing material: Flame-resistant resin (black)
Isolation: Pv1 to Pv2 to CT1 or CT2 to Di1 or Di2 to MV1 or
MV2 to Do1 or Do2 to Modbus to power
CT Input waveform
108(4.25)
mm (inch)
RMS sensing: Up to 15 % of 3rd harmonic content
Control mode: Standard PID, heating and cooling control
(ON/OFF, PID)
MODEL: TC10EM–[1]–M2
Proportional band (P): 0.1 to 3200.0 (temperature unit)
Integral time (I): 0 to 3999 sec.
ORDERING INFORMATION
• Code number: TC10EM-[1]-M2
Specify a code from below for [1].
(e.g. TC10EM-A-M2)
Derivative time (D): 0.0 to 999.9 sec.
Auto-tuning: Limit cycle method
Alarm: Deviation high & low, absolute high & low, etc.
Sampling cycle: 100 msec.
Control cycle: 1.0 to 99.9 sec.
[1] CONTROL OUTPUT
A: 0 – 20 mA DC (Load resistance 500 Ω max.)
Open-collector 2 points
(100 msec. fixed for Mv output 0 - 20 mA DC
and 0 - 10 V DC)
Mv output range: -5 - +105 % for output scale
Parameters: Stored in non-volatile memory; write/erase
cycle endurance: less than 1 000 000
Parameter setting: With front panel operation buttons or PC
configurator software (model: TC10CFG)
• Universal input
V: 0 – 10 V DC (Load resistance 2 kΩ max.)
Open-collector 2 points
P: 12 V pulse (Load resistance 600 Ω max.)
Open-collector 2 points
• Burnout
POWER INPUT
AC Power
• Control output
• Loop
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
TC10EM SPECIFICATIONS
ES-9581 Rev.4 Page 1/7
http://www.m-system.co.jp/
MODEL: TC10EM
• Bank
Man: Green LED turns on during manual mode
• Event input
• CT input
• Auto-tuning
Local: Green LED turns on when local SP chosen
At: Green LED turns on during auto-tuning
Out1: Green LED turns on when MV1 output
Out2: Green LED turns on when MV2 output
Engineering unit indication: Sticker label attached
DC, AC, mV, V, kV, μA, mA, A, kA, mW, W,
kW, var, kvar, Mvar, VA, Hz, Ω, kΩ, MΩ,
Refer to the instruction manual for detail.
■Recommended solderless terminal
3.3 (.13) max
cm, mm, m, m/sec, mm/min, cm/min, m/min,
m/h, m/s2, inch, ℓ, ℓ/s, ℓ/min, ℓ/h, m3, m3/sec,
m3
/min, m
3
/h, Nm /h, N·m, N/m , g, kg, kg/h,
3
2
N, kN, Pa, kPa, MPa, t, t/h, ℃, °F, %RH, J,
kJ, MJ, rpm, sec, min, min-1, pH, %, ppm, etc.
mm (inch)
MODBUS COMMUNICATION
Communication: Half-duplex, asynchronous, no procedure
Standard: Conforms to TIA/EIA-485-A
Transmission distance: 500 meters max.
Transmission media: Shielded twisted-pair cable
(CPEV-S 0.9 dia.)
INPUT SPECIFICATIONS
■ Universal input 1, 2 (Pv1, Pv2)
For type and range configuration, refer to the instruction
manual.
DC Current:
Input range: 0 - 20 mA DC
Input resistance: 49.9 Ω resistor incorporated
• DC voltage input
Node adress: 1 to 247
Data mode: RTU (Binary)
Parity: None, even or odd
Input resistance: ≥ 10 kΩ (-1000 to +1000 mV DC)
Input resistance: ≥ 1 MΩ (-10 to +10 V DC)
• Thermocouple
Baud rate: 4800, 9600, 19.2 k, 38.4 k, 57.6 k (bps)
Stop bit: 1 or 2
Node adress, parity, baud rate setting: With front panel
operation buttons or PC configurator software (model:
TC10CFG)
Input resistance: ≥ 10 kΩ
Input range: Refer to the table 1
Burnout sensing: ≤ 4 μA
Terminating resistor: Built-in (Enable by shorting between
pin 4 and 5)
Conformance range: Refer to the table 1
• RTD (2-wire or 3-wire)
Excitation: ≤ 0.33 mA
DISPLAY
Input range: Refer to the table 1
Allowable leadwire resistance: 20 Ω per wire
• Resistance
PV display: 5 digits 7-segment green LED, 19.5 mm (.77”)
height
SP display: 5 digits 7-segment red LED, 12.5 mm (.49”)
height, switchable to MV display
Excitation: ≤ 0.33 mA
Allowable leadwire resistance: 20 Ω per wire
• Potentiometer
Display range: -32000 to 32000
Decimal point position: 10–1 to 10–4 or none
Zero indication: Higher-digit zeros are suppressed.
Loop status indicators
Excitation: ≤ 0.33 mA
Input range: 0 to 4000 Ω
Allowable leadwire resistance: 20 Ω per wire
■ Clamp-on current sensor (CT1, CT2)
(Sensor model No.: AC input)
CLSE-R5: 0 – 5 A
Loop1: Amber LED turns on when loop 1 chosen
Loop2: Amber LED turns on when loop 2 chosen
Bank1: Green LED turns on when bank 1 chosen
Bank2: Green LED turns on when bank 2 chosen
Bank3: Green LED turns on when bank 3 chosen
Bank4: Green LED turns on when bank 4 chosen
Alarm1: Red LED turns on at alarm 1
Alarm2: Red LED turns on at alarm 2
Alarm3: Red LED turns on at alarm 3
Alarm4: Red LED turns on while setting is saving to the
non-volatile memory.
CLSE-05: 0 – 50 A
CLSE-10: 0 – 100 A
CLSE-20: 0 – 200 A
CLSE-40: 0 – 400 A
CLSE-60: 0 – 600 A
Frequency: 50 / 60 Hz (45 - 65 Hz)
Max. working voltage: 480 V AC (primary side)
Overload capacity:
Run: Green LED turns on while loop is in operation.
CLSE-R5: 10 A continuous, x40 (1 sec.)
TC10EM SPECIFICATIONS
ES-9581 Rev.4 Page 2/7
http://www.m-system.co.jp/
MODEL: TC10EM
CLSE-05: 60 A continuous, x40 (1 sec.)
CLSE-10: 120 A continuous, x40 (1 sec.)
CLSE-20: 240 A continuous, x40 (1 sec.)
CLSE-40: 480 A continuous, x40 (1 sec.)
CLSE-60: 720 A continuous, x40 (1 sec.)
Operational range
Approx. 7 VA at 200 V
Approx. 8 VA at 240 V
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 5 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Panel flush mounting
CLSE-R5: ≤ 5 A
Weight: 450 g (0.99 lb)
CLSE-05: ≤ 50 A
CLSE-10: ≤ 100 A
PERFORMANCE in percentage of span
Accuracy
CLSE-20: ≤ 200 A
CLSE-40: ≤ 400 A
• Pv1 or Pv2: Refer to "Input type, range & conversion
accuracy" section.
CLSE-60: ≤ 600 A
Caution 1: The output values may vary depending on the
accuracy of engagement at the clamp connection.
Caution 2: The sensor’s mechanical construction may cause
it to generate resonance sound. However, it does not affect
the perfomrance of the sensor.
■ Discrete Input (Di1, Di2)
• CT1 or CT2: ±2 % (sensor error margin not included)
• Mv1 or Mv2: ±0.5 %
Cold junction compensation error (thermocouple input):
±2.0°C at 0 – 50°C (±3.6°F at 32 – 122°F)
CJC sensor is adjacently attached to the input terminals.
CJC is available for each universal input 1 and 2.
Temp. coefficient
Contact rating: 3.3 V @1 mA
Detection levels:
• Pv1 or Pv2: ±0.03 %/°C (± 0.02 %/°F)
• CT1 or CT2: ±0.03 %/°C (± 0.02 %/°F)
Response time
≤ 15 kΩ / 0.5 V at close
≥ 350 kΩ / 2.5 V at open
• CT1 or CT2: ≤ 2 sec. (0 – 90 %)
OUTPUT SPECIFICATIONS
Four control outputs are configurable to Mv, Ao or Do.
■ Control Output (Mv1, Mv2)
Specify one type of output with the code number from 3
types shown below.
• Mv1 or Mv2: ≤ 1 sec. (0 – 90 %, DC output)
Burnout response (thermocouple, RTD input): ≤ 10 s
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (Pv1 to Pv2 to
CT1 or CT2 to Di1 or Di2 to MV1 or MV2 to Do1 or Do2 to
Modbus to power to ground)
• DC Current: 0 – 20 mA DC
Operational range: 0 – 23 mA DC
Load resistance: ≤ 500 Ω
STANDARDS & APPROVALS
EU conformity:
• DC Voltage: 0 – 10 V DC
Operational range: 0 - 11.5 V DC
Load resistance: ≥ 2 kΩ
EMC Directive
EMI EN 61000-6-4
• 12 V Voltage pulse
EMS EN 61000-6-2
Maximum frequency: 1 Hz
Low Voltage Directive
Minimum pulse width: 1 msec.
Hi level: 12 V ±15 %
EN 61010-1
Installation Category II
Lo level: ≤ 0.5 V
Pollution Degree 2
Load resistance: 600 Ω min.
■ Control Output (Do1, Do2)
• Open collector
Input to output to power – Reinforced insulation (300 V)
Input or output or power to Modbus – Basic insulation (300
V)
Maximum frequency: 1 Hz
RoHS Directive
EN 50581
Minimum pulse width: 1 msec.
Output rating: 50 V DC 100 mA (resistive load)
Saturation voltage: 0.5 V DC
INSTALLATION
Power Consumption
•AC:
Approx. 6 VA at 100 V
TC10EM SPECIFICATIONS
ES-9581 Rev.4 Page 3/7
http://www.m-system.co.jp/
MODEL: TC10EM
INPUT TYPE, RANGE & CONVERSION ACCURACY
INPUT TYPE
INPUT RANGE
0 to 20mA DC
ACCURACY
DC CURRENT
DC VOLTAGE
±20ꢀA
-1000 to +1000mV DC
When max. range*2 is ≥60mV ±20ꢀV
When max. range*2 is ≤120mV ±±0ꢀV
When max. range*2 is ≥120mV ±200ꢀV
±10mV ±0.1ꢁ
-10 to +10V DC
Total resistance up to 4000Ω*±
0 to 4000Ω
POTENTIOMETER
RESISTOR
±0.1Ω or ±0.1ꢁꢂ ,hicheꢃer is greater
±0.1Ω or ±0.1ꢁꢂ ,hicheꢃer is greater
°C
INPUT RANGE ACCURACY
F
゜
Thermocouple
＊1
＊1
CONFORMANCE RANGE
0 to 1760
INPUT RANGE ACCURACY
CONFORMANCE RANGE
ꢀ (PR)
0 to 1760
-270 to +1±70
-270 to +1000
-210 to +1200
-270 to +400
100 to 1ꢄ20
-50 to +1760
-50 to +1760
0 to 2±15
±1.ꢄ0
±0.40
±0.60
±0.70
±0.50
±2.00
±1.00
±1.00
±1.00
±0.50
±0.50
±0.±0
±0.±0
°C
±2 to ±200
-454 to +249ꢄ
-454 to +1ꢄ±2
-±46 to +2192
-454 to +752
212 to ±±0ꢄ
-5ꢄ to +±200
-5ꢄ to +±200
±2 to 4199
±±.24
±0.72
±1.0ꢄ
±1.26
±0.90
±±.60
±1.ꢄ0
±1.ꢄ0
±1.ꢄ0
±0.90
±0.90
±0.54
±0.54
±2 to ±200
-2±ꢄ to +249ꢄ
-274 to +1ꢄ±2
-292 to +2192
-274 to +752
752 to ±200
±92 to ±200
±2 to ±200
K (CA)
-150 to +1±70
-170 to +1000
-1ꢄ0 to +1200
-170 to +400
400 to 1760
200 to 1760
0 to 1760
E (CRC)
J (IC)
T (CC)
B (RH)
R
S
C (WRe 5-26)
0 to 2±15
±2 to 4199
N
-270 to +1±00
-200 to +600
-200 to +900
0 to 1±95
-1±0 to +1±00
-200 to +600
-200 to +900
0 to 1±95
-454 to +2±72
-±2ꢄ to +1112
-±2ꢄ to +1652
±2 to 254±
-202 to +2±72
-±2ꢄ to +1112
-±2ꢄ to +1652
±2 to 254±
U
L
P (Platinel ll)
F
゜
RTD
INPUT RANGE
-200 to +ꢄ50
-200 to +ꢄ50
-200 to +ꢄ50
-200 to +649
-200 to +510
-50 to +200
ACCURACY
±0.40
INPUT RANGE
ACCURACY
±0.72
Pt 100 (JIS ’97ꢂ IEC)
Pt 500
-±2ꢄ to +1562
-±2ꢄ to +1562
-±2ꢄ to +1562
-±2ꢄ to +1200
-±2ꢄ to +950
-5ꢄ to +±92
±0.40
±0.72
Pt 1000
±0.40
±0.72
Pt 50Ω (JIS‘ꢄ1)
JPt 100 (JIS’ꢄ9)
Ni 50ꢄ.4Ω
±0.60
±1.0ꢄ
±0.40
±0.72
±0.60
±1.0ꢄ
Cu 10 (25℃)
-50 to +250
±2.00
-5ꢄ to +4ꢄ2
±±.60
*1.Thermocouple: Add 2.0°C of cold-junction-compensation error.
*2. Max. range: absolute range (greater of 0ꢁ and 100ꢁ range ꢃalues)ꢂ ,hicheꢃer is greater.
*±. Refer to the operating manual for details.
EXTERNAL VIEW
■ FRONT VIEW
■ REAR VIEW
Cold Junction Compensation (2 CJM)
Loop status indicators
Run Man Local AT Out 1 Out 2
1
2
11
12
21
22
PV
3
4
5
13
14
15
23
24
25
PV Display
1
2
SP
MV
6
7
16
17
18
19
20
26
27
28
29
30
SP/MV Display
Loop
1
2
3
4
1
2
3
4
Config
8
Bank
Alarm
Loop1/2 SP/MV
9
Enter
Auto/Manu Local/Remote
Esc
10
Operation Buttons
Configuration Jack
TC10EM SPECIFICATIONS
ES-9581 Rev.4 Page 4/7
http://www.m-system.co.jp/
MODEL: TC10EM
COMMUNICATION CABLE CONNECTIONS
■ MASTER CONNECTION
HOST PC
TX+/RX+
TX–/RX–
SG
TC10EM
DA
TC10EM
DA
TERMINATOR
*1
NO.
ID
FUNCTION
DB
DB
6
7
DA
DB
DA
DB
RX+
RX–
*1. For using internal terminator, short-accross terminals 4 and 5.
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
6 – M3 Screw
Watertight Sealing
Terminal Cover
30 – M3 Terminal Screw
Mounting Bracket
1
2
11
21
22
23
24
25
26
27
28
29
30
12
13
14
15
16
17
18
19
20
3
4
5
6
7
8
9
10
2 (.08)
96 (3.78)
8 (.31)
92 (3.62)
98 (3.86)
100 (3.93)
■ PANEL CUTOUT unit: mm (inch)
＋0.8
92 −0
Pitch ≥122 (4.80)
Mounting bracket: 0.5 – 10 (0.02 to 0.39)
TC10EM SPECIFICATIONS
ES-9581 Rev.4 Page 5/7
http://www.m-system.co.jp/
MODEL: TC10EM
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
4
TERMINATOR
Indicator LEDs
...
5
6
Isolation
DA
DB
NC
NC
NC
11
MODBUS
7
1
2
A/D
Converter
Pv1
Comm.
Circuit
Control
Circuit
8
UNIVERSAL INPUT
1
1
3
9
4
10
Isolation
Isolation
Isolation
Isolation
2
5
+
15
16
17
CT1
A/D
Converter
Mv1
2
6
Output
Circuit
+
–
CT2
Mv2
2
7
21
22
23
24
+
+
–
28
29
30
Do1
A/D
Converter
Output
Circuit
Pv2
UNIVERSAL INPUT
Do2
Isolation
1
2
3
U(+)
18
19
20
POWER
V (–)
NC
Di1
Input
Circuit
Di2
Display/
Setting
JACK
■ UNIVERSAL INPUT CONNECTION (Pv2) e.g.
■ UNIVERSAL INPUT CONNECTION (Pv1) e.g.
■ CT1 / CT2 CONNECTION e.g.
•DC Voltage (-10 – +10V DC)
•DC Current (0 – 20mA DC)
•DC Voltage (-10 – +10V DC)
•DC Current (0 – 20mA DC)
•Clamp-on current Sensor (model : CLSE)
Power Side
k
+
–
11
12
13
14
+
–
21
22
23
24
25
INPUT
INPUT
k
l
26
27
l
Load Side
•DC Voltage (-1000 – +1000mV DC)
•DC Voltage (-1000 – +1000mV DC)
11
21
■ DISCRETE INPUT CONNECTION e.g.
–
+
12
13
14
–
+
22
23
24
Di1
18
INPUT
INPUT
Di2
19
20
•Thermocouple
•Thermocouple
–
–
11
12
13
14
21
22
23
24
–
–
■ CONTROL OUTPUT 1 & 2 CONNECTION e.g.
CJC
+
CJC
+
SENSOR
SENSOR
15
16
17
+
+
–
+
+
Mv1
comp. leadwire
comp. leadwire
Mv2
•RTD/Resistor (3-wire)
•RTD/Resistor (3-wire)
11
12
13
14
21
22
23
24
A
B
B
A
B
B
■ CONTROL OUTPUT 3 & 4 CONNECTION e.g.
Do1
28
29
+
–
Do2
+
–
•RTD/Resistor (2-wire)
•RTD/Resistor (2-wire)
30
11
12
13
14
21
22
23
24
A
B
A
B
•Potentiometer
•Potentiometer
11
12
13
14
21
22
23
24
max.
+
max.
+
–
–
min.
min.
TC10EM SPECIFICATIONS
ES-9581 Rev.4 Page 6/7
http://www.m-system.co.jp/
MODEL: TC10EM
Specifications are subject to change without notice.
TC10EM SPECIFICATIONS
ES-9581 Rev.4 Page 7/7
http://www.m-system.co.jp/
相关型号：
TC10V.TB
Zener Diode, 10V V(Z), 5%, 0.5W, Silicon, Unidirectional, DO-35, HERMETIC SEALED, GLASS PACKAGE-2
TAK_CHEONG
TC10V.TR
Zener Diode, 10V V(Z), 5%, 0.5W, Silicon, Unidirectional, DO-35, HERMETIC SEALED, GLASS PACKAGE-2
TAK_CHEONG
TC10VB
Zener Diode, 10V V(Z), 2%, 0.2W, Silicon, Unidirectional, ROHS COMPLIANT, PLASTIC, SIMILAR TO SC-90, 2 PIN
TAK_CHEONG
TC10VC
Zener Diode, 10V V(Z), 5%, 0.2W, Silicon, Unidirectional, ROHS COMPLIANT, PLASTIC, SIMILAR TO SC-90, 2 PIN
TAK_CHEONG
©2020 ICPDF网 联系我们和版权申明