TM-R-D [MSYSTEM]
CONTACT TELEMETERING MODULE;型号: | TM-R-D |
厂家: | M-SYSTEM |
描述: | CONTACT TELEMETERING MODULE |
文件: | 总4页 (文件大小:62K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Telemetering System
MODEL
CONTACT TELEMETERING MODULE
TMR/TMT
MODEL & SUFFIX CODE SELECTION
50
(1.97)
TM❑–❑
MODEL
80
(3.15)
INPUT
Dry contact
OUTPUT
M
•U
N
l
IT
M
o
d
e
TM
R
OUTPUT
ON
OFF
R : Relay contact
T : Open collector
POWER INPUT
123
(4.84)
mm (inch)
AC Power
DC Power
Functions & Features
B : 100V AC
C : 110V AC
D : 115V AC
F : 120V AC
G : 200V AC
H : 220V AC
J : 240V AC
S : 12V DC*
R : 24V DC*
• Transmitting 1-point contact signal through NTT
(Nippon Telephone & Telegraph) personal telecom-
munication line of 50 b/s • Approved of Technical
Requirements Compliance Approval by Japan Ap-
proval Institute for Telecommunications Equipment
• Approval No. M90-N227-0 • Applicable to vari-
ous cables types • No interference by induction noise
• Lightning protection applicable • No field adjust-
ment required • Compact plug-in construction easy
to install and maintain
*24V DC (Code R) and 12V DC (Code S) are not ap-
proved by Japan Approvals Institute for Telecommu-
nications Equipment.
Therefore an individual application will be necessary
for using the TMA on NTT telecom. line.
ORDERING INFORMATION
INPUT & OUTPUT
Specify code number. (e.g. TMR-B)
❑INPUT: dry contact
Sensing: approx. 18V DC @5mA
ON/OFF level: ≤3kΩ for ON; ≥30kΩ for OFF
Maximum leadwire resistance: 3kΩ including
return
GENERAL SPECIFICATIONS
Construction: plug-in
Connection: M3.5 screw terminals
Housing material: flame-resistant resin (black)
Isolation: input to output to power
❑OUTPUT
•Relay Contact: 100V AC @5A (cosø=1)
24V DC @5A (resistive load)
electrical life 10 × 104 cycles (rate 30/min.)
Maximum switching voltage: 380V AC or 125V DC
Maximum switching power: 500VA or 120W
Minimum load: 5V DC @10mA (18V DC @5mA)
Mechanical life: 5 × 107 cycles
Maximum frequency: 1 Hz
•Open Collector: 24V DC @100mA
Maximum frequency: 20 Hz
Saturation voltage: 1.8V DC
Remark: The output pulse width is adjusted to 25
millisec. even when the input pulse width is narrower
than 25 millisec.
P. 1 / 4
ES-5221 Rev.9
TMR / TMT
INSTALLATION
EXPLANATIONS
Power input
❑AVAILABLE NTT LINE
AC:
DC:
rating ±10%, 50/60 ±2 Hz, approx. 2VA
rating ±10% (ripple 10% p-p max.)
approx. 80mA at 24V
Among the several circuit lines opened by NTT (Nip-
pon Telephone & Telegraph), the TMR/TMT utilizes
the “special DC line” of 50 b/s.
approx. 160mA at 12V
The following shows the conditions to use this line.
Operating temperature: -5 to +60°C (23 to 140°F)
Operating humidity: 30 to 90% RH (non-condensing)
Mounting: surface or DIN rail
ITEM
DATA
Transmission speed
Technical configuration
50 b/s max.
2-wire (metalic return)
4-wire (metalic return
Dimensions: W50×H80×D123 mm (1.97"×3.15"×4.84")
Weight:
350 g (0.77 lbs)
Communication
Intersection
Uni-directional, full-duplex
Not allowed
PERFORMANCE
Response time: ≤10 millisec.
Line voltage effect: ±0.1% over voltage range
Insulation resistance: ≥100MΩ with 500V DC
Dielectric strength: 1000V AC @1 minute
(input to output or power)
Circuit protection
Required
Electrical characteristics Current 45mA max.
Voltage between lines 100V max.
Voltage to ground 50V max.
2000V AC @1 minute (output to ground)
Specifications subject to change without notice.
P. 2 / 4
ES-5221 Rev.9
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
❑TMR (relay)
OPEN
COLLECTOR
RELAY
5mA
Current
Detector
Frequency
Limiter
+
1
2
7
8
3
4
5
6
OUTPUT 1
OUTPUT 2
Constant
Current
–
Relay
U(+)
POWER
V(–)
Base Socket
❑TMT (open collector)
OPEN
COLLECTOR
RELAY
5mA
Current
Detector
Frequency
Limiter
+
+
–
+
–
1
2
7
8
3
4
5
6
OUTPUT 1
OUTPUT 2
Constant
Current
–
Open
Collector
U(+)
POWER
V(–)
Base Socket
Output Connection Examples
❑Open Collector
❑Relay
•AC Powered
+
–
+
–
+
–
+
–
3
4
5
6
3
4
LOAD
Relay or
Counter Coil
5
6
Varistor or Spark
Quenching Circuit
LOAD
•DC Powered
3
4
LOAD
LOAD
Relay or
Counter Coil
5
6
Spark Quenching Diode
P. 3 / 4
ES-5221 Rev.9
TMR / TMT
TERMINAL CONNECTIONS
TMR/TMT
MDP-24-1
MDP-24-1
TMR/TMT
LEASED CIRCUIT
50 bps
1
2
7
8
3
4
P+
P–
S+
S–
S+
S–
P+
P–
1
2
3
4
7
8
OUTPUT
G
G
+
POWER
–
1
8
5
4
5
4
1
8
POWER
7
7
MAX-100/200
MAX-100/200
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENT mm (inch)
CLAMP
(top & bottom)
7.8 (.31)
DIN RAIL
35mm wide
6
5
4
3
2–4.5 (.18) dia.
MTG HOLE
15 (.59) deep
7
8
1
2
8–M3.5
SCREW
50 (1.97)
103 (4.06)
123 (4.84)
40 (1.57)
50 (1.97)
[3.3 (.13)]
•When mounting, no extra space is needed between units.
Specifications subject to change without notice.
P. 4 / 4
ES-5221 Rev.9
相关型号:
©2020 ICPDF网 联系我们和版权申明