DE6E3KJ472MB3B_技术文档

Reference Specification

Type KJ

Safety Standard Certified Lead Type Disc Ceramic Capacitors for Automotive

Product specifications in this catalog are as of Jun. 2023, and are subject to change or

obsolescence without notice.

Please consult the approval sheet before ordering.Please read rating and Cautions first.

Reference only

ꢀꢀꢀCAUTION

ꢀꢀ1. OPERATING VOLTAGE

1) Do not apply a voltage to a safety standard certified product that exceeds the rated voltage as called out

in the specifications. Applied voltage between the terminals of a safety standard certified product shall be

less than or equal to the rated voltage (+10 %). When a safety standard certified product is used as a

DC voltage product, the AC rated voltage value becomes the DC rated voltage value.

(Example:AC250 V (r.m.s.) rated product can be used as DC250 V (+10 %) rated product.)

If both AC rated voltage and DC rated voltage are specified, apply the voltage lower than the respective

rated voltage.

1-1) When a safety standard certified product is used in a circuit connected to a commercial power supply,

ensure that the applied commercial power supply voltage including fluctuation should be less than 10 %

above its rated voltage.

1-2) When using a safety standard certified product as a DC rated product in circuits other than those

connected to a commercial power supply.

When AC voltage is superimposed on DC voltage, the zero-to-peak voltage shall not exceed the ratedꢀDC

voltage. When AC voltage or pulse voltage is applied, the peak-to-peak voltage shall not exceed the rated

DC voltage.

Typical Voltage Applied to the DC Capacitor

(E: Maximum possible applied voltage.)

2) Abnormal voltages (surge voltage, static electricity, pulse voltage, etc.) shall not exceed the rated DC

voltage.

ꢀꢀ2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT

Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range.

Be sure to take into account the heat generated by the capacitor itself.

When the capacitor is used in a high-frequency current, pulse current or the like, it may have the self-

generated heat due to dielectric-loss. Applied voltage should be the load such as self-generated heatꢀis

within 20 ℃ on the condition of atmosphere temperature 25 ℃. When measuring, use aꢀthermocouple of

small thermal capacity-K of Φ0.1 mm and be in the condition where capacitor is not affected by radiant

heat of other components and wind of surroundings. Excessive heat may lead to deterioration of the

capacitor’s characteristics and reliability. (Never attempt to perform measurement with the cooling fan

running. Otherwise, accurate measurement cannot be ensured.)

ꢀꢀ3. TEST CONDITION FOR WITHSTANDING VOLTAGE

1) TEST EQUIPMENT

Test equipment for AC withstanding voltage should be used with the performance of the wave similar

to 50/60 Hz sine wave.

If the distorted sine wave or over load exceeding the specified voltage value is applied, the defective

may be caused.

EGD28B

1/22

Reference only

2) VOLTAGE APPLIED METHOD

When the withstanding voltage is applied, capacitor’s lead or terminal should be firmly connected to the

out-put of the withstanding voltage test equipment, and then the voltage should be raised from near zero

to the test voltage.

If the test voltage without the raise from near zero voltage would be applied directly to capacitor, test

voltage should be applied with the *zero cross. At the end of the test time, the test voltage should be

reduced to near zero, and then capacitor’s lead or terminal should be taken off the out-put of the

withstanding voltage test equipment.

If the test voltage without the raise from near zero voltage would

be applied directly to capacitor, the surge voltage may arise,

and therefore, the defective may be caused.

voltage sine wave

0 V

zero cross

*ZERO CROSS is the point where voltage sine wave pass 0 V.

- See the right figure -

ꢀꢀ4. FAIL-SAFE

When capacitor would be broken, failure may result in a short circuit. Be sure to provide an appropriate

fail-safe function like a fuse on your product if failure would follow an electric shock, fire or fume.

ꢀꢀ5. VIBRATION AND IMPACT

Do not expose a capacitor or its leads to excessive shock or vibration during use. Excessive shock or

vibration may cause to fatigue destruction of lead wires mounted on the circuit board. Please take

measures to hold a capacitor on the circuit boards by adhesive, molding resin or coating and other.

Please confirm there is no influence of holding measures on the product with a intended equipment.

ꢀꢀ6. SOLDERING

When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the

capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may

result in thermal shocks that can crack the ceramic element.

When soldering capacitor with a soldering iron, it should be performed in following conditions.

Temperature of iron-tip

Soldering iron wattage

Soldering time

: 400 ℃ max.

: 50 W max.

: 3.5 s max.

ꢀꢀ7. BONDING, RESIN MOLDING AND COATING

In case of bonding, molding or coating this product, verify that these processes do not affect the quality

of capacitor by testing the performance of the bonded, molded or coated product in the intended

equipment.

In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins

containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer

coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short

circuit.

The variation in thickness of adhesive, molding resin or coating may cause a outer coating resin cracking

and/or ceramic element cracking of a capacitor in a temperature cycling.

ꢀꢀ8. TREATMENT AFTER BONDING, RESIN MOLDING AND COATING

When the outer coating is hot (over 100 ℃) after soldering, it becomes soft and fragile.

So please be careful not to give it mechanical stress.

Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial

dispersion when the product is used.

EGD28B

2/22

Reference only

ꢀꢀ9. OPERATING AND STORAGE ENVIRONMENT

The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store capacitors

in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are

present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify that

these processes do not affect product quality by testing the performance of a cleaned, bonded or molded

product in the intended equipment. Store the capacitors where the temperature and relative humidity do not

exceed -10 to 40 ℃ and 15 to 85 %.

Use capacitors within 6 months after delivered. Check the solderability after 6 months or more.

ꢀꢀ10. LIMITATION OF APPLICATIONS

Please contact us before using our products for the applications listed below which require especially high

reliability for the prevention of defects which might directly cause damage to the third party’s life, body or

property.

1. Aircraft equipment

2. Aerospace equipment

3. Undersea equipment

4. Power plant control equipment

5. Medical equipment

6. Transportation equipment (vehicles, trains, ships, etc.)

7. Traffic signal equipment

8. Disaster prevention / crime prevention equipment

9. Data-processing equipment exerting influence on public

10. Application of similar complexity and/or reliability requirements to the applications listed in the above.

NOTICE

ꢀꢀ1. CLEANING (ULTRASONIC CLEANING)

To perform ultrasonic cleaning, observe the following conditions.

Rinse bath capacity : Output of 20 watts per liter or less.

Rinsing time : 5 min maximum.

Do not vibrate the PCB/PWB directly.

Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires.

ꢀꢀ2. CAPACITANCE CHANGE OF CAPACITORS

• Class 1 capacitors

Capacitance might change a little depending on a surrounding temperature or an applied voltage.

Please contact us if you use for the strict time constant circuit.

• Class 2 and 3 capacitors

Class 2 and 3 capacitors like temperature characteristic B, E and F have an aging characteristic,

whereby the capacitor continually decreases its capacitance slightly if the capacitor leaves for a long

time. Moreover, capacitance might change greatly depending on a surrounding temperature or an

applied voltage. So, it is not likely to be able to use for the time constant circuit.

Please contact us if you need a detail information.

ꢀꢀ3. PERFORMANCE CHECK BY EQUIPMENT

Before using a capacitor, check that there is no problem in the equipment's performance and the

specifications.

Generally speaking, CLASS 2 ceramic capacitors have voltage dependence characteristics and

temperature dependence characteristics in capacitance. So, the capacitance value may change

depending on the operating condition in a equipment. Therefore, be sure to confirm the apparatus

performance of receiving influence in a capacitance value change of a capacitor, such as leakage

current and noise suppression characteristic.

Moreover, check the surge-proof ability of a capacitor in the equipment, if needed, because the surge

voltage may exceed specific value by the inductance of the circuit.

EGD28B

3/22

Reference only

ꢀꢀꢀNOTE

1. Please make sure that your product has been evaluated in view of your specifications with our product

being mounted to your product.

2. You are requested not to use our product deviating from this specification.

EGD28B

4/22

Reference only

1.Application

This specification is applied to Safety Standard Certified Lead Type Disc Ceramic Capacitors Type KJ

in accordance with AEC-Q200 used for the battery charger for Electric Vehicles and Plug-in Hybrid.

The safety standard certification is obtained by Class X1, Y2.

Approval standard and certified number

Standard number

UL60384-14/CSA E60384-14

EN60384-14

* Certified number

E37921

Rated voltage

UL/cUL

ENEC

(VDE)

X1: AC440 V(r.m.s.)

Y2: AC300 V(r.m.s.)

40031217

IEC60384-14

*Above Certified number may be changed on account of the revision of standards and

ꢀthe renewal of certification.

2.Rating

2-1.Operating temperature range

-40 ~ 125°C

2-2.Rated Voltage

X1: AC440 V(r.m.s.)

Y2: AC300 V(r.m.s.)

DC1,000 V

2-3.Part number configuration

ex.)

DE6

E3

KJ

Certified

Type

472

M

A3

Lead

Style

B

Individual

Series

Temperature

Characteristics

Capacitance

Tolerance

Package

Specification

• Series

DE6 denotes class X1,Y2.

• Temperature Characteristics

Please confirm detailed specification on [Specification and test methods].

Code

B3

E3

Temperature Characteristics

B

E

• Certified Type

This denotes safety certified type name Type KJ.

• Capacitance

The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.

472

ex.) In case of

.

47 × 10²= 4700 pF

• Capacitance Tolerance

Please refer to [ Part number list ].

• Lead Style

* Please refer to [ Part number list ].

Code

Lead Style

A*

B*

N*

Vertical crimp long type

Vertical crimp short type

Vertical crimp taping type

Solder coated copper wire is applied for termination.

TEIKAKU

5/22

Reference only

• Package

Code

Package

Ammo pack taping type

Bulk type

A

B

• Individual Specification

Murata’s control code

Please refer to Part number list .

Note) Murata part numbers might be changed depending on Lead Style or any other changes.

Therefore, please specify only the Certified Type (KJ) and capacitance of products in the

parts list when it is required for applying safety standard of electric equipment.

3.Marking

Capacitance

： 3 digit system

Capacitance tolerance

Certified type

： Code

： KJ

Rated voltage mark

Class code

： 300~

： X1Y2

Manufacturing year

Manufacturing month

： Letter code(The last digit of A.D. year.)

： Code

ex.)

YEAR

2022

MONTH

12(December)

*

2D

* From January to September : “1” to “9”,

October : “O” , November : “N” , December : “D”

Company name code

：

(Made in Thailand)

(Example)

472M

KJ 300～

X1Y2

2D

TEIKAKU

6/22

Reference only

4. Part number list

Note) The mark ' * ' of Lead Style differ from lead spacing (F) and lead diameter (d).

Please see the following list about details.

Unit : mm

Dimension (mm)

Pack

qty.

(pcs)

Customer

Part Number

Murata

Part Number

Cap.

(pF)

Cap.

tol.

Lead

Style

T.C.

D

T

F

d

DE6B3KJ101KA3BE01J

DE6B3KJ151KA3BE01J

DE6B3KJ221KA3BE01J

DE6B3KJ331KA3BE01J

DE6B3KJ471KA3BE01J

DE6B3KJ681KA3BE01J

DE6E3KJ102MA3B

B

E

100 ±10%

150 ±10%

220 ±10%

330 ±10%

470 ±10%

680 ±10%

1000 ±20%

1500 ±20%

2200 ±20%

3300 ±20%

4700 ±20%

6.0

5.0

6.0

7.0

7.5

0.6 A3

250

200

8.0

6.0

7.0

8.0

9.0

7.0

DE6E3KJ152MA3B

8.0

DE6E3KJ222MA3B

9.0

DE6E3KJ332MA3B

10.0

12.0

DE6E3KJ472MA3B

PNLIST

7/22

Reference only

Note) The mark ' * ' of Lead Style differ from lead spacing (F) and lead diameter (d).

Please see the following list about details.

Unit : mm

Dimension (mm)

Pack

qty.

(pcs)

Customer

Part Number

Murata

Part Number

Cap.

(pF)

Cap.

tol.

Lead

Style

T.C.

D

T

F

d

DE6B3KJ101KA4BE01J

DE6B3KJ151KA4BE01J

DE6B3KJ221KA4BE01J

DE6B3KJ331KA4BE01J

DE6B3KJ471KA4BE01J

DE6B3KJ681KA4BE01J

DE6E3KJ102MA4B

B

E

100 ±10%

150 ±10%

220 ±10%

330 ±10%

470 ±10%

680 ±10%

1000 ±20%

1500 ±20%

2200 ±20%

3300 ±20%

4700 ±20%

6.0

5.0 10.0

6.0 10.0

7.0 10.0

0.6 A4

250

200

8.0

6.0

7.0

8.0

9.0

7.0

DE6E3KJ152MA4B

8.0

DE6E3KJ222MA4B

9.0

DE6E3KJ332MA4B

10.0

12.0

DE6E3KJ472MA4B

PNLIST

8/22

Reference only

Note) The mark ' * ' of Lead Style differ from lead spacing (F) and lead diameter (d).

Please see the following list about details.

Unit : mm

Dimension (mm)

Pack

qty.

(pcs)

Customer

Part Number

Murata

Part Number

Cap.

(pF)

Cap.

tol.

Lead

Style

T.C.

D

T

F

d

DE6B3KJ101KB3BE01J

DE6B3KJ151KB3BE01J

DE6B3KJ221KB3BE01J

DE6B3KJ331KB3BE01J

DE6B3KJ471KB3BE01J

DE6B3KJ681KB3BE01J

DE6E3KJ102MB3B

B

E

100 ±10%

150 ±10%

220 ±10%

330 ±10%

470 ±10%

680 ±10%

1000 ±20%

1500 ±20%

2200 ±20%

3300 ±20%

4700 ±20%

6.0

5.0

6.0

7.0

7.5

0.6 B3

500

250

8.0

6.0

7.0

8.0

9.0

7.0

DE6E3KJ152MB3B

8.0

DE6E3KJ222MB3B

9.0

DE6E3KJ332MB3B

10.0

12.0

DE6E3KJ472MB3B

PNLIST

9/22

Reference only

Note) The mark ' * ' of Lead Style differ from lead spacing (F) and lead diameter (d).

Please see the following list about details.

Unit : mm

Dimension (mm)

Pack

qty.

(pcs)

Customer

Part Number

Murata

Part Number

Cap.

(pF)

Cap.

tol.

Lead

Style

T.C.

D

T

F

d

DE6B3KJ101KB4BE01J

DE6B3KJ151KB4BE01J

DE6B3KJ221KB4BE01J

DE6B3KJ331KB4BE01J

DE6B3KJ471KB4BE01J

DE6B3KJ681KB4BE01J

DE6E3KJ102MB4B

B

E

100 ±10%

150 ±10%

220 ±10%

330 ±10%

470 ±10%

680 ±10%

1000 ±20%

1500 ±20%

2200 ±20%

3300 ±20%

4700 ±20%

6.0

5.0 10.0

6.0 10.0

7.0 10.0

0.6 B4

500

250

8.0

6.0

7.0

8.0

9.0

7.0

DE6E3KJ152MB4B

8.0

DE6E3KJ222MB4B

9.0

DE6E3KJ332MB4B

10.0

12.0

DE6E3KJ472MB4B

PNLIST

10/22

Reference only

Note) The mark ' * ' of Lead Style differ from lead spacing (F) ,

lead diameter (d) and pitch of compoment (P).

Please see the following list or taping specification about details.

Unit : mm

Dimension (mm)

Pack

qty.

(pcs)

Customer

Part Number

Murata

Part Number

Cap.

(pF)

Cap.

tol.

Lead

Style

T.C.

D

T

F

d

P

DE6B3KJ101KN3AE01J

DE6B3KJ151KN3AE01J

DE6B3KJ221KN3AE01J

DE6B3KJ331KN3AE01J

DE6B3KJ471KN3AE01J

DE6B3KJ681KN3AE01J

DE6E3KJ102MN3A

B

E

100 ±10%

150 ±10%

220 ±10%

330 ±10%

470 ±10%

680 ±10%

1000 ±20%

1500 ±20%

2200 ±20%

3300 ±20%

4700 ±20%

6.0

5.0

6.0

7.0

7.5

0.6 15.0 N3

700

8.0

6.0

7.0

8.0

9.0

7.0

DE6E3KJ152MN3A

8.0

DE6E3KJ222MN3A

9.0

DE6E3KJ332MN3A

10.0

12.0

DE6E3KJ472MN3A

PNLIST

11/22

Reference only

Note) The mark ' * ' of Lead Style differ from lead spacing (F) ,

lead diameter (d) and pitch of compoment (P).

Please see the following list or taping specification about details.

Unit : mm

Dimension (mm)

Pack

qty.

(pcs)

Customer

Part Number

Murata

Part Number

Cap.

(pF)

Cap.

tol.

Lead

Style

T.C.

D

T

F

d

P

DE6B3KJ101KN4AE01J

DE6B3KJ151KN4AE01J

DE6B3KJ221KN4AE01J

DE6B3KJ331KN4AE01J

DE6B3KJ471KN4AE01J

DE6B3KJ681KN4AE01J

DE6E3KJ102MN4A

B

E

100 ±10%

150 ±10%

220 ±10%

330 ±10%

470 ±10%

680 ±10%

1000 ±20%

1500 ±20%

2200 ±20%

3300 ±20%

4700 ±20%

6.0

5.0 10.0

6.0 10.0

7.0 10.0

0.6 25.4 N4

400

8.0

6.0

7.0

8.0

9.0

7.0

DE6E3KJ152MN4A

8.0

DE6E3KJ222MN4A

9.0

DE6E3KJ332MN4A

10.0

12.0

DE6E3KJ472MN4A

PNLIST

12/22

Reference only

5. Specification and test methods

Item

No.

1

Specification

No marked defect on appearance

Test method

Appearance and dimensions

The capacitor should be inspected by naked eyes for visible

form. Please refer to [Part number list] evidence of defect.

on dimensions.

Dimensions should be measured with slide calipers.

2

3

Marking

To be easily legible.

The capacitor should be inspected by naked eyes.

Capacitance

Within specified tolerance.

The capacitance should be measured at 20 °C with 1±0.1 kHz and

AC5 V(r.m.s.) max..

4

5

Dissipation Factor (D.F.)

DF≦0.025

The dissipation factor should be measured at 20 °C with 1±0.1 kHz

and AC5 V(r.m.s.) max..

Insulation Resistance (I.R.)

10,000 MΩ min.

The insulation resistance should be measured with DC500±50 V

within 60±5 s of charging. The voltage should be applied to the

capacitor through a resistor of 1 MΩ.

6

Dielectric

strength

Between lead No failure.

wires

The capacitor should not be damaged when AC2,600 V(r.m.s.)

<50/60 Hz> is applied between the lead wires for 60 s.

Body

insulation

No failure.

First, the terminals of the capacitor should be connected together.

Then, a metal foil should be

closely wrapped around

the body of the capacitor

to the distance of

Metal

foil

about 3 to 4 mm

from each terminal.

Then, the capacitor

should be inserted into

About

3 to 4 mm

Metal

balls

a container filled with

metal balls of about 1 mm diameter.

Finally, AC2,600 V(r.m.s.) <50/60 Hz> is applied for 60 s between

the capacitor lead wires and metal balls.

7

Temperature characteristic

Char. B : Within ±10 %

Char. E : Within +20/-55 %

(Temp. range : -25 to 85°C)

The capacitance measurement should be made at each step

specified in Table.

Step

1

2

3

4

5

Temp.(°C)

20±2

-25±2

20±2

85±2

20±2

Pre-treatment : Capacitor should be stored at 125±3 °C for 1 h,

then placedat *room condition for 24±2 h before

initial measurements.

8

Solderability

Lead wire should be soldered with

Should be placed into steam aging for 8 h ±15 min. After the steam

uniform coating on the axial direction aging, the lead wire of a capacitor should be dipped into a ethanol

over 3/4 of the circumferential

direction.

solution of 25 % rosin and then into molten solder for 5+0/-0.5 sec.

The depth of immersion is up to about 1.5 to 2.0 mm from the root

of lead wires.

Temp. of solder :

Lead Free Solder(Sn-3Ag-0.5Cu) 245±5 °C

H63 Eutectic Solder 235±5 °C

* "room condition" Temperature : 15 to 35 °C, Relative humidity : 45 to 75 %, Atmospheric pressure : 86 to 106kPa

ESKJ01J

13/22

Reference only

Specification

Item

No.

9

Test method

Resistance to Appearance

No marked defect.

As shown in figure, the lead wires should be immersed in solder of

260±5 °C up to 1.5 to 2.0 mm from the root of terminal for 10±1 s.

Soldering Heat

Capacitance

Within ±10 %

(Non-preheat)

change

I.R.

1,000 MΩ min.

Dielectric

strength

Per item 6

Pre-treatment : Capacitor should be stored at 125±3 °C for 1 h,

then placed at *room condition for 24±2 h before

initial measurements.

Post-treatment : Capacitor should be stored for 1 to 2 h at *room

condition.

10 Resistance to Appearance

No marked defect.

Within ±10 %

First the capacitor should be stored at 120+0/-5 °C for 60+0/-5 s.

Then, as in figure, the lead wires should be immersed solder of

260+0/-5 °C up to 1.5 to 2.0 mm from the root of terminal for

7.5+0/-1 s.

Soldering Heat

(On-preheat)

change

Capacitance

I.R.

1,000 MΩ min.

Dielectric

strength

Per item 6

Pre-treatment : Capacitor should be stored at 125±3 °C for 1 h,

then placed at *room condition for 24±2 h before

initial measurements.

Post-treatment : Capacitor should be stored for 1 to 2 h at *room

condition.

11 Vibration

Appearance

Capacitance

No marked defect.

Within the specified tolerance.

DF≦0.025

Solder the capacitor and gum up the body to the test jig (glass

epoxy board) by resin (adhesive).

Dissipation

Factor (D.F.)

resin (adhesive)

The capacitor should be firmly soldered to the supporting lead wire,

1.5 mm in total amplitude, with about 20 minutes rate of vibration

change from 10 Hz to 2,000 Hz and back to 10 Hz. This motion

should be applied for 12 times in each 3 mutually perpendicular

directions (total of 36 times). The acceleration is 5 g max..

12 Mechanical

Shock

Appearance

Capacitance

No marked defect.

Within the specified tolerance.

DF≦0.05

Solder the capacitor and gum up the body to the test jig (glass

epoxy board) by resin (adhesive).

(Compliant

with

AEC-Q200)

Dissipation

Factor (D.F.)

resin (adhesive)

I.R.

10,000 MΩ min.

Three shocks in each direction should be applied along 3 mutually

perpendicular axes to and from of the test specimen (18 shocks).

The specified test pulse should be Half-sine and should have a

duration : 0.5ms, peak value : 100 g and velocity change : 4.7 m/s.

* "room condition" Temperature : 15 to 35 °C, Relative humidity : 45 to 75 %, Atmospheric pressure : 86 to 106kPa

ESKJ01J

14/22

Reference only

Specification

No.

Item

Appearance

Test method

13 Humidity

No marked defect.

Set the capacitor for 1,000±12 h at 85±3 °C in 80 to 85 % relative

humidity.

(Under steady

Capacitance

change

Char. B : Within ±10 %

Char. E : Within ±15 %

state)

Pre-treatment : Capacitor should be stored at 125±3 °C for 1 h,

ꢀꢀꢀꢀꢀꢀꢀ ꢀꢀꢀthen placed at *room condition for 24±2 h before

initial measurements.

Dissipation

Factor (D.F.)

DF≦0.05

I.R.

3,000 MΩ min.

Post-treatment : Capacitor should be stored for 1 to 2 h at *room

condition.

Dielectric

strength

Per item 6

14 Humidity

loading

Appearance

No marked defect.

Apply the rated voltage for 1,000±12 h at 85±3 °C in 80 to 85 %

relative humidity

Capacitance

change

Char. B : Within ±10 %

Char. E : Within ±15 %

Pre-treatment : Capacitor should be stored at 125±3 °C for 1 h,

ꢀꢀꢀꢀꢀꢀꢀ ꢀꢀꢀthen placed at *room condition for 24±2 h before

initial measurements.

Dissipation

Factor (D.F.)

DF≦0.05

I.R.

3,000 MΩ min.

Post-treatment : Capacitor should be stored for 1 to 2 h at *room

condition.

15 Life

Appearance

No marked defect.

Within ±20 %

Impulse voltage

Each individual capacitor should be subjected to a 5 kV impulses

for three times or more. Then the capacitors are applied to life test.

Capacitance

change

I.R.

3,000 MΩ min.

Front time (T1) = 1.7 μs=1.67T

Time to half-value (T2) = 50 μs

Dielectric

strength

Per item 6

The capacitors are placed in a circulating air oven for a period of

1,000 h.

The air in the oven is maintained at a temperature of 125+2/-0 °C,

and relative humidity of 50 % max.. Throughout the test, the

capacitors are subjected to a AC510 V(r.m.s.) <50/60 Hz>

alternating voltage of mains frequency, except that once each hour

the voltage is increased to AC1,000 V(r.m.s.) for 0.1 s.

Pre-treatment : Capacitor should be stored at 125±3 °C for 1 h,

ꢀꢀꢀꢀꢀꢀꢀ ꢀꢀꢀthen placed at *room condition for 24±2 h before

initial measurements.

Post-treatment : Capacitor should be stored for 1 to 2 h at *room

condition.

16 Flame test

The capacitor flame discontinue as

follows.

The capacitor should be subjected to applied flame for 15 s. and

then removed for 15 s until 5 cycles are completed.

Cycle

1 to 4

5

Time

30 s max.

60 s max.

(in mm)

17 Robustness of Tensile

terminations

Lead wire should not cut off. Capacitor As shown in the figure at right, fix

should not be broken.

the body of the capacitor and apply

a tensile weight gradually to each

lead wire in the radial direction of the

capacitor up to 10 N, and keep it

for 10±1 s.

Bending

Each lead wire should be subjected to 5 N of weight and bent 90°

at the point of egress, in one direction, then returned to its original

position, and bent 90° in the opposite direction at the rate of one

bend in 2 to 3 s.

* "room condition" Temperature : 15 to 35 °C, Relative humidity : 45 to 75 %, Atmospheric pressure : 86 to 106kPa

ESKJ01J

15/22

Reference only

No.

Item

Specification

Test method

18 Active flammability

The cheese-cloth should not be on fire. The capacitors should be individually wrapped in at least one but

more than two complete layers of cheese-cloth. The capacitor

should be subjected to 20 discharges. The interval between

successive discharges should be 5 s. The UAc should be

maintained for 2 min after the last discharge.

C1,2

: 1 μF±10 %,

C3 : 0.033 μF± 5% 10 kV

L1 to L4 : 1.5 mH±20 % 16A Rod core choke

R

: 100 Ω±2 %,

Ct : 3 μF±5 % 10 kV

UAc

Cx

F

: UR ±5 %

UR : Rated working voltage

: Capacitor under test

: Fuse, Rated 10 A

: Voltage applied to Ct

Ut

19 Passive flammability

The burning time should not be

exceeded the time 30 s.

The tissue paper should not ignite.

The capacitor under test should be held in the flame in the position

which best promotes burning. Time of exposure to flame is for

30 s.

Length of flame : 12±1 mm

Gas burner

Gas

: Length 35 mm min.

Inside Dia.

0.5±0.1 mm

Outside Dia. 0.9 mm max.

: Butane gas Purity 95 % min.

Capacitor

About 8mm

Gas burner

Flame

200±5 mm

45°

Tissue

About 10 mm thick board

20 Temperature Appearance

No marked defect.

The capacitor should be subjected to 1,000 temperature cycles.

cycle

(Compliant

with

AEC-Q200)

Capacitance

change

Char. B : Within ±10 %

Char. E : Within ±20 %

Step Temperature(C) Time(min)

1

2

3

4

-55+0/-3

Room temp.

125+3/-0

30

3

Dissipation

Factor (D.F.)

I.R.

DF≦0.05

30

3

Room temp.

3,000 MΩ min.

Dielectric

strength

Per item 6

Pre-treatment : Capacitor should be stored at 125±3 °C for 1 h,

then placed at *room condition for 24±2 h.

Post-treatment : Capacitor should be stored for 24±2 h at *room

condition.

21 High

Capacitance

Within ±20 %

Sit the capacitor for 1,000±12 h at 150±3 °C.

Temperature change

Exposure

(Storage)

(Compliant

with AEC-

Q200)

Pre-treatment : Capacitor should be stored at 125±3 °C for 1 h,

then placed at *room condition for 24±2 h.

Post-treatment : Capacitor should be stored for 24±2 h at *room

condition.

Dissipation

Factor (D.F.)

DF≦0.05

I.R.

1,000 MΩ min.

* "room condition" Temperature : 15 to 35 °C, Relative humidity : 45 to 75 %, Atmospheric pressure : 86 to 106kPa

ESKJ01J

16/22

Reference only

Specification

Item

Test method

No.

22 Thermal Shock Appearance

(Compliant

No marked defect except color change The capacitor should be subjected to 300 cycles.

of outer coating.

Step Temperature(C) Time(min)

with

AEC-Q200)

1

2

-55+0/-3

125+3/-0

30

Capacitance

Char. B : Within ±10 %

Char. E : Within ±20 %

change

Dissipation

Factor (D.F.)

DF≦0.05

Pre-treatment: Capacitor should be stored at 125±3 °C for 1 h,

then placed at *room condition for 24±2 h.

Post-treatment: Capacitor should be stored for 24±2 h at *room

condition.

I.R.

3,000 MΩ min.

23 Resistance to Appearance

No marked defect.

Per MIL-STD-202 Method 215

Solvents

Capacitance

Char. B : Within ±10 %

Char. E : Within ±20 %

(Compliant

change

Solvent 1 : 1 part (by volume) of isopropyl alcohol

3 parts (by volume) of mineral spirits

Solvent 2 : Terpene defluxer

Solvent 3 : 42 parts (by volume) of water

1part (by volume) of propylene glycol

monomethyl ether

with AEC-

Dissipation

Factor (D.F.)

I.R.

DF≦0.05

Q200)

3,000 MΩ min.

1 part (by volume) of monoethanolamine

24 Biased

Humidity

(Compliant

with AEC-

Q200)

Appearance

No marked defect.

Apply DC1.3+0.2/-0 V (add 100 kΩ resistor) at 85±3 °C and 80 to

85 % humidity for 1,000±12 h. The charge/discharge current is less

than 50 mA.

Capacitance

change

Char. B : Within ±10 %

Char. E : Within ±15 %

Dissipation

Factor (D.F.)

DF≦0.05

Pre-treatment : Capacitor should be stored at 125±3 °C for 1 h,

then placed at *room condition for 24±2 h.

Post-treatment : Capacitor should be stored for 24±2 h at *room

condition.

I.R.

3,000 MΩ min.

25 Resistance

(Compliant

with AEC-

Q200)

Appearance

No marked defect.

Apply the 24 h heat (25 to 65 °C) and humidity (80 to 98 %)

treatment shown below, 10 consecutive times.

Capacitance

change

Char. B : Within ±10 %

Char. E : Within ±20 %

Dissipation

DF≦0.05

Factor (D.F.)

I.R.

3,000 MΩ min.

Post-treatment: Capacitor should be stored for 24±2 h at *room

condition.

* "room condition" Temperature : 15 to 35 °C, Relative humidity : 45 to 75 %, Atmospheric pressure : 86 to 106kPa

ESKJ01J

17/22

Reference only

6. Packing specification

・Bulk type (Package : B)

The size of packing case and packing way

Polyethylene bag

Partition

125 max.

270 max.

Unit : mm

340 max.

The number of packing = ^*1Packing quantity × ^*2n

*1 : Please refer to [Part number list].

*2 : Standard n = 20 (bag)

Note)

The outer package and the number of outer packing be changed by the order getting amount.

EKBCDE02A

18/22

Reference only

・Ammo pack taping type (Package : A)

・The tape with capacitors is packed zigzag into a case.

・When body of the capacitor is piled on other body under it.

・There should be 3 pitches and over without capacitors in leader and trailer.

The size of packing case and packing way

240 max.

Position of label

340 max.

Unit : mm

60 max.

Hold down tape

Capacitor

Base tape

Hold down

tape upper

EKTDE10A

19/22

Reference only

7. Taping specification

7-1. Dimension of capacitors on tape

Vertical crimp taping type < Lead Style : N3 >

Pitch of component 15.0 mm / Lead spacing 7.5 mm

Unit : mm

Item

Code

P

Dimensions

15.0+/-2.0

15.0+/-0.3

7.5+/-1.0

Remarks

Pitch of component

Pitch of sprocket hole

P0

F

Lead spacing

Length from hole center to component center

Length from hole center to lead

Body diameter

P2

P1

D

7.5+/-1.5

Deviation of progress direction

3.75+/-1.0

Please refer to [Part number list ].

Deviation along tape, left or right

Carrier tape width

ΔS

W

0+/-2.0

18.0+/-0.5

9.0+/-0.5

They include deviation by lead bend.

Position of sprocket hole

W1

Deviation of tape width direction

Lead distance between reference and bottom

planes

H0

18.0+2.0/-0

Protrusion length

+0.5～-1.0

4.0+/-0.1

0.60+/-0.05

0.6+/-0.3

1.5 max.

Diameter of sprocket hole

Lead diameter

ΦD0

Φd

t1

Total tape thickness

They include hold down tape

thickness.

Total thickness of tape and lead wire

Deviation across tape, front

Deviation across tape, rear

Portion to cut in case of defect

Hold down tape width

t2

Δh1

Δh2

L

2.0 max.

11.0+0/-1.0

11.5 min.

1.5+/-1.5

W0

W2

e

Hold down tape position

Coating extension on lead

Body thickness

Up to the end of crimp

Please refer to [Part number list ].

T

ETP1N301B

20/22

Reference only

Vertical crimp taping type < Lead Style : N4 >

Pitch of component 25.4 mm / Lead spacing 10.0 mm

Unit : mm

Item

Code

P

Dimensions

25.4+/-2.0

12.7+/-0.3

10.0+/-1.0

7.7+/-1.5

Remarks

Pitch of component

Pitch of sprocket hole

Lead spacing

P0

F

Length from hole center to lead

Body diameter

P1

D

Please refer to [Part number list ].

Deviation along tape, left or right

Carrier tape width

ΔS

W

0+/-2.0

18.0+/-0.5

9.0+/-0.5

They include deviation by lead bend.

Position of sprocket hole

W1

Deviation of tape width direction

Lead distance between reference and bottom

planes

H0

18.0+2.0/-0

Protrusion length

+0.5～-1.0

4.0+/-0.1

0.60+/-0.05

0.6+/-0.3

1.5 max.

Diameter of sprocket hole

Lead diameter

ΦD0

Φd

t1

Total tape thickness

They include hold down tape

thickness.

Total thickness of tape and lead wire

Deviation across tape, front

Deviation across tape, rear

Portion to cut in case of defect

Hold down tape width

t2

Δh1

Δh2

L

2.0 max.

11.0+0/-1.0

11.5 min.

1.5+/-1.5

W0

W2

e

Hold down tape position

Coating extension on lead

Body thickness

Up to the end of crimp

Please refer to [Part number list ].

T

ETP1N401B

21/22

Reference only

ꢀꢀ7-2. Splicing way of tape

1) Adhesive force of tape is over 3 N at test condition as below.

W

Hold down tape

Base tape

2) Splicing of tape

ꢀꢀꢀa) When base tape is spliced

•Base tape should be spliced by cellophane tape.

(Total tape thickness should be less than 1.05 mm.)

Progress direction

in production line

Hold down tape

Base tape

About 30 to 50

No lifting for the

Cellophane tape

direction of progressing

Unit : mm

ꢀꢀꢀb) When hold down tape is spliced

ꢀꢀꢀ •Hold down tape should be spliced with overlapping.

(Total tape thickness should be less than 1.05 mm.)

20 to 60

Hold down tape

Base tape

Unit : mm

Progress direction

in production line

ꢀꢀꢀc) When both tape are spliced

•Base tape and hold down tape should be spliced with splicing tape.

3) Missing components

•There should be no consecutive missing of more than three components.

•The number of missing components should be not more than 0.5 % of

total components that should be present in a Ammo pack.

ETP2D03

22/22


型号：	DE6E3KJ472MB3B
厂家：	muRata
描述：	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] 医疗医疗器械
文件：	总23页 (文件大小：646K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

DE6E3KJ472MB3B [MURATA]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E