OKL-T/6-W5P-C [MURATA]
Programmable Output 6-Amp iLGA SMT PoLs; 可编程输出6安培ILGA SMT政客
| 型号： | OKL-T/6-W5P-C |
| 厂家： | 
muRata |
| 描述： | Programmable Output 6-Amp iLGA SMT PoLs |
| 文件： | 总15页 (文件大小：980K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
OKL-T/6-W5 Series
s
Programmable Output 6-Amp iLGA SMT PoLs
PRODUCT OVERVIEW
The OKL-T/6-W5 series are non-isolated
efficient Point of Load (PoL) module features
Point-of-Load (PoL) DC/DC power converters for
programmable output voltage and On/Off control.
embedded applications. Featuring inspectable Land These converters also include under voltage lock
Grid Array (LGA) format, the OKL-T/6-W5 measures out (UVLO), output short circuit protection, over-
only 0.48 x 0.48 x 0.283 inches max. (12.2 x 12.2
x 7.2 mm max.).
The wide input range is 2.4 to 5.5 Volts DC.
The maximum output current is 6 Amps. Based
on fixed-frequency synchronous buck converter
switching topology, the high power conversion
current and over temperature protections.
An optional sequence/tracking feature allows
power sequencing of PoL’s. These units meet all
standard UL/EN/IEC 60950-1 safety certifications
(2nd Edition) and RoHS-6 hazardous substance
compliance.
Typical unit
FEATURES
■ 2.4-5.5Vdc input voltage range
■ Programmable output voltage from 0.6-3.3Vdc
■ High power conversion efficiency at 93.5%
■ Inspectable Land Grid Array
Contents
Page
Description, Connection Diagram, Photograph
Ordering Guide, Model Numbering, Product Label
1
2
■ Drives up to 300 μF ceramic capacitive loads
■ On/Off control
Mechanical Specifications, Input/Output Pinout
Output Voltage Adustment, Application Notes
Soldering Guidelines
Performance Data and Oscillograms
Tape & Reel Information
3
5
7
8
■ Optional Sequence/Tracking operation
■ Outstanding thermal derating performance
■ Over temperature and over current protection
■ Meets UL/EN/IEC 60950-1 safety, 2nd Edition
■ RoHS-6 hazardous substance compliance
15
Connection Diagram
+Vin
+Vout
Sense
tꢀ4XJUDIJOH
tꢀ'JMUFST
F1
On/Off
Control
Controller
tꢀ$VSSFOUꢀ4FOTF
External
DC
Trim
Power
Source
Reference and
Error Amplifier
Open = On
Closed = Off
(Positive
On/Off)
Common
Common
Sequence/Tracking
(OKL2 Models)
Figure 1. OKL-T/6-W5
Note: Murata Power Solutions strongly recommends an external input fuse, F1. See specifications.
For full details go to
www.murata-ps.com/rohs
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 1 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
Performance Specifications and Ordering Guide
ORDERING GUIDE
Output
Input
Package–Pinout P83
Efficiency
On/Off Seq/
Polarity Track
Model Number
Regulation (max.)
Vin nom. Range Iin, no load Iin, full load
Vout Iout (Amps, Power R/N (mV p-p)
Case C83
inches (mm)
(Volts) ➀
max.)
(Watts)
Max. ➃
(Volts) (Volts) (mA) ➄ (Amps) ➁
Line
Load
Min. Typ.
0.48x0.48x0.283 max
(12.2x12.2x7.2) max
OKL-T/6-W5P-C
OKL-T/6-W5N-C
0.6-3.3
6
19.8
25
0.35% 0.35%
0.35% 0.35%
0.35% 0.35%
5
5
5
5
2.4-5.5
2.4-5.5
2.4-5.5
2.4-5.5
25
25
25
25
4.24
4.24
4.24
4.24
91.5% 93.5% Pos.
91.5% 93.5% Neg.
no
no
0.48x0.48x0.283 max
(12.2x12.2x7.2) max
0.6-3.3
6
6
6
19.8
19.8
19.8
25
25
25
0.48x0.48x0.283 max
(12.2x12.2x7.2) max
OKL2-T/6-W5P-C 0.6-3.3
OKL2-T/6-W5N-C 0.6-3.3
91.5% 93.5% Pos. yes
91.5% 93.5% Neg. yes
0.48x0.48x0.283 max
(12.2x12.2x7.2) max
0.35% 0.35%
➀
➁
The output range (50% load) is limited by Vin. See detailed specs for full conditions.
➂
Use adequate ground plane and copper thickness adjacent to the converter.
ꢀꢁRipple and Noise (R/N) are shown at Vout=1V. See specs for details.
➄ꢁNo load input current is shown at Vout = 3.3V.
All specifications are at nominal line voltage, Vout=nominal (3.3V for W5 models) and full load,
+25 deg.C. unless otherwise noted.
Output capacitors are 10 μF ceramic. Input cap is 22 μF. See detailed specifications.
I/O caps are necessary for our test equipment and may not be needed for your application.
PART NUMBER STRUCTURE
OK L 2 - T / 6 - W5 N - C
Okami Non-isolated PoL
LGA Surface Mount
RoHS Hazardous
Substance Compliance
C = RoHS-6 (does not claim EU RoHS exemption
7b–lead in solder)
Sequence/tracking
Blank = Not installed
2 = Installed
On/Off Polarity
P = Positive Polarity
N = Negative Polarity
Trimmable Output
Voltage Range
0.6-3.3Vdc
Input Voltage Range
2.4-5.5Vdc
Maximum Rated Output
Current in Amps
Product Label
Because of the small size of these products, the product label contains a
character-reduced code to indicate the model number and manufacturing date
code. Not all items on the label are always used. Please note that the label
differs from the product photograph. Here is the layout of the label:
Model Number
Product Code
L01006
OKL-T/6-W5P-C
OKL-T/6-W5N-C
OKL2-T/6-W5P-C
OKL2-T/6-W5N-C
L00006
L21006
L20006
XXXXXX
Product code
Revision level
Mfg.
date
code
YMDX Rev.
The manufacturing date code is four characters:
Figure 2. Label Artwork Layout
First character – Last digit of manufacturing year, example 2009
Second character – Month code (1 through 9 and O through D)
Third character – Day code (1 through 9 = 1 to 9, 10=O and
11 through 31 = A through Z)
The label contains three rows of information:
First row – Murata Power Solutions logo
Second row – Model number product code (see table)
Third row – Manufacturing date code and revision level
Fourth character – Manufacturing information
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 2 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
MECHANICAL SPECIFICATIONS
Top View
INPUT/OUTPUT CONNECTIONS
0.043 (1.09)
NOM. PCB
THK
0.48
(12.19)
Pin
1
Function
On/Off Control*
VIN
Bottom View
2
3
Ground
4
VOUT
5
Sense
6
7
8
9
10
11
12
Trim
Ground
0.48
(12.19)
No Connection
Sequence/Tracking
No Connection
No Connection
No Connection
Side View
*The Remote On/Off can be provided with
either positive (P suffix) or negative (N
suffix) polarity
0.283
(7.2)
max.
End View
Recommended Footprint
-through the Board-
Bottom View
0.480 (12.19)
0.135
(3.43)
0.180
(4.57)
0.045
(1.14)
0.070 x 0.160 x3
(1.77 x 4.07)
4
3
2
2
3
4
Vin
Gnd
0.420 (10.67)
0.375 (9.53)
Gnd
Vin
0.180 (4.57)
0.180 (4.57)
C
L
0.135 (3.43)
5
On/Off
Sense
NC
5
11
6
1
Sense
On/Off
C
0.240 (6.10)
0.150 (3.81)
1
L
0.090
(2.29)
10
NC
NC
11
6
10
9
Seq
Trim
Gnd
NC
0.060 (1.52)
0
9
Seq NC Gnd NC
Trim
8
7
12
12
7
8
Dimensions are in inches (mm shown for ref. only).
0.090
(2.29)
Third Angle Projection
0.180 0.090
(4.57) (2.29)
0.040 x 0.040 (9 places)
(1.01 x 1.01)
Tolerances (unless otherwise specified):
.XX 0.02 (0.5)
.XXX 0.010 (0.25)
Angles 1ꢀ
Components are shown for reference only.
Figure 3. OKL-T/6-W5 Mechanical Outline
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 3 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
Dynamic Characteristics
Performance and Functional Specifications
See Note 1
Dynamic Load Response
50ꢁSec max. to within 2% of final value
Input
(50-100% load step, di/dt=1A/μSec)
Peak Deviation
(Note 1)
350 mV
Input Voltage Range
Isolation
See Ordering Guide and Note 7.
Start-Up Time
(Vin on or On/Off to Vout regulated)
6 mSec for Vout=nominal (Vin On)
6 mSec for Vout=nominal (Remote On/Off)
Not isolated
2.05 V
Start-Up Voltage
100 kHz
Switching Frequency
600 KHz
Undervoltage Shutdown (see Note 15)
Overvoltage Shutdown
1.92 V
None
Environmental
OKL Models
Reflected (Back) Ripple Current (Note 2) TBD mA pk-pk
Calculated MTBF (hours)
Telecordia method (4a)
OKL2 Models
5,341
Internal Input Filter Type
Capacitive
5,573,000
,000
(hours)
Calculated MTBF
Recommended External Fuse
Reverse Polarity Protection
TBD
MIL-HDBK-217N2 method (4b)
5,999,000
5,176,000
None, Install external fuse
Operating Temperature Range (Ambient, all output ranges)
Input Current:
Full Load Conditions
Inrush Transient
Shutdown Mode (Off, UV, OT)
Output in Short Circuit
Low Line (Vin=Vmin)
See derating curves
-40 to +85 °C. with derating (Note 9)
See Ordering Guide
TBD
1 mA
10 mA
A2Sec.
Storage Temperature Range
Thermal Protection/Shutdown
-55 to +125 °C.
Included in PWM
Relative Humidity
To 85%/+85 C., non-condensing
°
4.68 A (Vout = 3.3V)
Remote On/Off Control (Note 5)
Negative Logic
Physical
ON = Open pin or -0.2V to Vin -1.6V max.
OFF = Vin -0.8V min. to +Vin max.
ON = Open pin (internally pulled up) or
+1.2V to +Vin max.
OFF = -0.3V to +0.3V max. or ground
TBD
Outline Dimensions
Weight
See Mechanical Specifications
0.06 ounces (1.6 grams)
Positive Logic
Safety
Meets UL/cUL 60950-1, CSA-
C22.2 No. 60950-1, IEC/EN 60950-1,
2nd Edition
Current
RoHS-6 (does not claim EU RoHS exemption
7b–lead in solder)
Tracking/Sequencing (optional)
Slew Rate
Tracking accuracy, rising input
Tracking accuracy, falling input
Restriction of Hazardous Substances
2 Volts per millisecond, max.
Vout = 100 mV of Sequence In
Vout = 100 mV of Sequence In
Absolute Maximum Ratings
Input Voltage (Continuous or transient)
On/Off Control
0 V. to +6 Volts max.
0 V. min. to +Vin max.
Output
Output Power
19.8W max.
Input Reverse Polarity Protection
Output Current (Note 7)
None, Install external fuse
Output Voltage Range
See Ordering Guide
No minimum load
2 % of Vnominal
See Ordering Guide
None
Current-limited. Devices can withstand a
sustained short circuit without damage.
The outputs are not intended to accept
appreciable reverse current.
Minimum Loading
Accuracy (50% load, untrimmed)
Voltage Output Range (Note 13)
Overvoltage Protection (Note 16)
Temperature Coefficient
Ripple/Noise (20 MHz bandwidth)
Line/Load Regulation
Storage Temperature
Lead Temperature
-55 to +125 °C.
See soldering specifications
TBD
Absolute maximums are stress ratings. Exposure of devices to greater than any of
any of these conditions may adversely affect long-term reliability. Proper operation
under conditions other than those listed in the Performance/Functional Specifications
Table is not implied nor recommended.
See Ordering Guide and note 8
See Ordering Guide and note 10
See Ordering Guide
Efficiency
Maximum Capacitive Loading (Note 14)
Cap-ESR=0.001 to 0.01 Ohms
Cap-ESR >0.01 Ohms
Specification Notes:
300 ꢁF
TBD
(1) Specifications are typical at +25 °C, Vin=nominal (+5V), Vout=nominal (+3.3V), full load, external caps and
natural convection unless otherwise indicated. Extended tests at full power must supply substantial forced airflow.
Current Limit Inception (Note 6)
(98% of Vout setting, after warm up) 12 Amps
All models are tested and specified with external 10ꢁF ceramic output capacitors and a 22 ꢁF external
input capacitor. All capacitors are low ESR types. These capacitors are necessary to accommodate our test
equipment and may not be required to achieve specified performance in your applications. However, Murata
Power Solutions recommends installation of these capacitors. All models are stable and regulate within
spec under no-load conditions.
Short Circuit Mode
Short Circuit Current Output
Protection Method
10 mA
Hiccup autorecovery upon overload
removal. (Note 17)
Continuous, no damage
(output shorted to ground)
Converter will start up if the external
output voltage is less than Vnominal.
(2) Input Back Ripple Current is tested and specified over a 5 Hz to 20 MHz bandwidth. Input filtering is Cin=2 x
100 ꢁF ceramic, Cbus=1000 ꢁF electrolytic, Lbus=1 ꢁH.
Short Circuit Duration
Prebias Startup
(3) Note that Maximum Power Derating curves indicate an average current at nominal input voltage. At higher
temperatures and/or lower airflow, the DC/DC converter will tolerate brief full current outputs if the total
RMS current over time does not exceed the Derating curve.
(4a) Mean Time Before Failure is calculated using the Telcordia (Belcore) SR-332 Method 1, Case 3, ground fixed
conditions, Tpcboard=+25 ꢀC, full output load, natural air convection.
(4b) Mean Time Before Failure is calculated using the MIL-HDBK-217N2 method, ground benign, +25ºC., full
output load, natural convection.
(5) The On/Off Control Input should use either a switch or an open collector/open drain transistor referenced
to -Input Common. A logic gate may also be used by applying appropriate external voltages which do not
exceed +Vin.
(6) Short circuit shutdown begins when the output voltage degrades approximately 2% from the selected
setting.
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 4 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
APPLICATION NOTES
Specification Notes, Cont.:
(7) Please observe the voltage input and output specifications in the Voltage Range Graph on page 7.
Input Fusing
(8) Output noise may be further reduced by adding an external filter. At zero output current, the output may
contain low frequency components which exceed the ripple specification. The output may be operated
indefinitely with no load.
Certain applications and/or safety agencies may require fuses at the inputs
of power conversion components. Fuses should also be used when there
is the possibility of sustained input voltage reversal which is not current-
limited. For greatest safety, we recommend a fast blow fuse installed in the
ungrounded input supply line.
(9) All models are fully operational and meet published specifications, including “cold start” at –40ꢀ C.
(10) Regulation specifications describe the deviation as the line input voltage or output load current is varied
from a nominal midpoint value to either extreme.
(11) Other input or output voltage ranges will be reviewed under scheduled quantity special order.
(12) Maximum PC board temperature is measured with the sensor in the center of the converter.
(13) Do not exceed maximum power specifications when adjusting the output trim.
The installer must observe all relevant safety standards and regulations.
For safety agency approvals, install the converter in compliance with the
end-user safety standard.
(14) The maximum output capacitive loads depend on the the Equivalent Series Resistance (ESR) of the external
output capacitor and, to a lesser extent, the distance and series impedance to the load. Larger caps will
reduce output noise but may change the transient response. Newer ceramic caps with very low ESR may
require lower capacitor values to avoid instability. Thoroughly test your capacitors in the application. Please
refer to the Output Capacitive Load Application Note.
Input Under-Voltage Shutdown and Start-Up Threshold
(15) Do not allow the input voltage to degrade lower than the input undervoltage shutdown voltage at all times.
Otherwise, you risk having the converter turn off. The undervoltage shutdown is not latching and will
attempt to recover when the input is brought back into normal operating range.
Under normal start-up conditions, converters will not begin to regulate
properly until the rising input voltage exceeds and remains at the Start-Up
Threshold Voltage (see Specifications). Once operating, converters will not
turn off until the input voltage drops below the Under-Voltage Shutdown
Limit. Subsequent restart will not occur until the input voltage rises again
above the Start-Up Threshold. This built-in hysteresis prevents any unstable
on/off operation at a single input voltage.
(16) The outputs are not intended to sink appreciable reverse current.
(17) “Hiccup” overcurrent operation repeatedly attempts to restart the converter with a brief, full-current output.
If the overcurrent condition still exists, the restart current will be removed and then tried again. This short
current pulse prevents overheating and damaging the converter. Once the fault is removed, the converter
immediately recovers normal operation.
Output Voltage Adustment
The output voltage may be adjusted over a limited range by connecting an
external trim resistor (Rtrim) between the Trim pin and Ground. The Rtrim
resistor must be a 1/10 Watt precision metal film type, 0.5% accuracy or
better with low temperature coefficient, 100 ppm/ C. or better. Mount the
°
resistor close to the converter with very short leads or use a surface mount
trim resistor.
Users should be aware however of input sources near the Under-Voltage
Shutdown whose voltage decays as input current is consumed (such as
capacitor inputs), the converter shuts off and then restarts as the external
capacitor recharges. Such situations could oscillate. To prevent this, make
sure the operating input voltage is well above the UV Shutdown voltage AT
ALL TIMES.
In the table below, the calculated resistance is given. Do not exceed the
specified limits of the output voltage or the converter’s maximum power
rating when applying these resistors. Also, avoid high noise at the Trim
input. However, to prevent instability, you should never connect any capaci-
tors to Trim.
Start-Up Delay
Assuming that the output current is set at the rated maximum, the Vin to
Vout Start-Up Delay (see Specifications) is the time interval between the
point when the rising input voltage crosses the Start-Up Threshold and the
fully loaded regulated output voltage enters and remains within its specified
regulation band. Actual measured times will vary with input source imped-
ance, external input capacitance, input voltage slew rate and final value of
the input voltage as it appears at the converter.
Resistor Trim Equation, OKL-T/6-W5 models:
1.2
VOUT – 0.6
___________
RTRIM (Kꢀ) =
These converters include a soft start circuit to moderate the duty cycle of
the PWM controller at power up, thereby limiting the input inrush current.
The On/Off Remote Control interval from inception to Vout regulated
assumes that the converter already has its input voltage stabilized above
the Start-Up Threshold before the On command. The interval is measured
from the On command until the output enters and remains within its
specified accuracy band. The specification assumes that the output is fully
loaded at maximum rated current.
Output Voltage
3.3 V.
Calculated Rtrim (KΩ)
0.444
0.632
1.0
2.5 V.
1.8 V.
1.5 V.
1.333
2.0
1.2 V.
Recommended Input Filtering
1.0 V.
3.0
The user must assure that the input source has low AC impedance to
provide dynamic stability and that the input supply has little or no inductive
content, including long distributed wiring to a remote power supply. The
converter will operate with no additional external capacitance if these
conditions are met.
0.6 V.
∞ (open)
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 5 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
For best performance, we recommend installing a low-ESR capacitor
immediately adjacent to the converter’s input terminals. The capacitor
should be a ceramic type such as the Murata GRM32 series or a polymer
type. Initial suggested capacitor values are 10 to 22 μF, rated at twice the
expected maximum input voltage. Make sure that the input terminals do
not go below the undervoltage shutdown voltage at all times. More input
bulk capacitance may be added in parallel (either electrolytic or tantalum)
if needed.
COPPER STRIP
+OUTPUT
RLOAD
SCOPE
C1
C2
Recommended Output Filtering
-OUTPUT
The converter will achieve its rated output ripple and noise with no
additional external capacitor. However, the user may install more exter-
nal output capacitance to reduce the ripple even further or for improved
dynamic response. Again, use low-ESR ceramic (Murata GRM32 series)
or polymer capacitors. Initial values of 10 to 47 μF may be tried, either
single or multiple capacitors in parallel. Mount these close to the converter.
Measure the output ripple under your load conditions.
COPPER STRIP
C1 = 1μF CERAMIC
C2 = 10μF CERAMIC
LOAD 2-3 INCHES (51-76mm) FROM MODULE
Figure 5: Measuring Output Ripple and Noise (PARD)
Use only as much capacitance as required to achieve your ripple and
noise objectives. Excessive capacitance can make step load recovery
sluggish or possibly introduce instability. Do not exceed the maximum rated
output capacitance listed in the specifications.
Minimum Output Loading Requirements
All models regulate within specification and are stable under no load to full
load conditions. Operation under no load might however slightly increase
output ripple and noise.
Input Ripple Current and Output Noise
All models in this converter series are tested and specified for input
reflected ripple current and output noise using designated external input/
output components, circuits and layout as shown in the figures below. The
Cbus and Lbus components simulate a typical DC voltage bus. Please note
that the values of Cin, Lbus and Cbus will vary according to the specific
converter model.
Temperature Derating Curves
The graphs in the next section illustrate typical operation under a variety of
conditions. The Derating curves show the maximum continuous ambient air
temperature and decreasing maximum output current which is accept-
able under increasing forced airflow measured in Linear Feet per Minute
(“LFM”). Note that these are AVERAGE measurements. The converter will
accept brief increases in current or reduced airflow as long as the average
is not exceeded.
TO
CURRENT
PROBE
OSCILLOSCOPE
Note that the temperatures are of the ambient airflow, not the converter
itself which is obviously running at higher temperature than the outside
air. Also note that very low flow rates (below about 25 LFM) are similar to
“natural convection”, that is, not using fan-forced airflow.
+INPUT
-INPUT
LBUS
+
–
+
–
VIN
CBUS
CIN
Murata Power Solutions makes Characterization measurements in a
closed cycle wind tunnel with calibrated airflow. We use both thermo-
couples and an infrared camera system to observe thermal performance.
C
IN = 2 x 100μF, ESR < 700mΩ @ 100kHz
BUS = 1000μF, ESR < 100mΩ @ 100kHz
C
LBUS = 1μH
Figure 4: Measuring Input Ripple Current
In figure 5, the two copper strips simulate real-world printed circuit
impedances between the power supply and its load. In order to minimize
circuit errors and standardize tests between units, scope measurements
should be made using BNC connectors or the probe ground should not
exceed one half inch and soldered directly to the test circuit.
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 6 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
Output Current Limiting
Voltage Range Graph
Current limiting inception is defined as the point at which full power falls
below the rated tolerance. See the Performance/Functional Specifica-
tions. Note particularly that the output current may briefly rise above its
rated value in normal operation as long as the average output power is
not exceeded. This enhances reliability and continued operation of your
application. If the output current is too high, the converter will enter the
short circuit condition.
Please observe the limits below for voltage input and output ranges. These
limits apply at all output currents.
6
5
4
Vin=2.4V / Vout=1.8V
3
Output Short Circuit Condition
When a converter is in current-limit mode, the output voltage will drop as
the output current demand increases. If the output voltage drops too low
(approximately 98% of nominal output voltage for most models), the mag-
netically coupled voltage used to develop PWM bias voltage will also drop,
thereby shutting down the PWM controller. Following a time-out period, the
PWM will restart, causing the output voltage to begin rising to its appropri-
ate value. If the short-circuit condition persists, another shutdown cycle
will initiate. This rapid on/off cycling is called “hiccup mode”. The hiccup
cycling reduces the average output current, thereby preventing excessive
internal temperatures and/or component damage.
2
1
0
Upper Limit
Lower Limit
0.5
1
1.5
2
2.5
3
3.5
Output Voltage (V)
Soldering Guidelines
Murata Power Solutions recommends the specifications below when installing these
converters. These specifications vary depending on the solder type. Exceeding these
specifications may cause damage to the product. Your production environment may differ
The “hiccup” system differs from older latching short circuit systems
because you do not have to power down the converter to make it restart.
The system will automatically restore operation as soon as the short circuit
condition is removed.
therefore please thoroughly review these guidelines with your process engineers.
Reflow Solder Operations for surface-mount products (SMT)
For Sn/Ag/Cu based solders:
Remote On/Off Control
The remote On/Off Control can be specified with either positive or negative
logic polarity. Please refer to the Connection Diagram on page 1 for On/Off
connections.
Preheat Temperature
Time over Liquidus
Less than 1 ºC. per second
45 to 75 seconds
Maximum Peak Temperature
Cooling Rate
260 ºC.
Positive polarity models are enabled when the On/Off pin is left open or
is pulled high to +Vin with respect to –Vin. An internal bias current causes
the open pin to rise to +Vin. Positive-polarity devices are disabled when the
On/Off is grounded or brought to within a low voltage (see Specifications)
with respect to –Vin.
Less than 3 ºC. per second
For Sn/Pb based solders:
Preheat Temperature
Time over Liquidus
Less than 1 ºC. per second
60 to 75 seconds
Negative polarity devices are on (enabled) when the On/Off is open or
brought to within a low voltage (see Specifications) with respect to –Vin.
The device is off (disabled) when the On/Off is pulled high with respect to
–Vin (see specifications).
Maximum Peak Temperature
Cooling Rate
235 ºC.
Less than 3 ºC. per second
Recommended Lead-free Solder Reflow Profile
Dynamic control of the On/Off function should be able to sink the speci-
fied signal current when brought low and withstand appropriate voltage
when brought high. Be aware too that there is a finite time in milliseconds
(see Specifications) between the time of On/Off Control activation and
stable, regulated output. This time will vary slightly with output load type
and current and input conditions.
Peak Temp.
235-260° C
250
200
Reflow Zone
150
100
50
Soaking Zone
120 sec max
time above 217° C
45-75 sec
Output Capacitive Load
These converters do not require external capacitance added to achieve
rated specifications. Users should only consider adding capacitance to
reduce switching noise and/or to handle spike current load steps. Install
only enough capacitance to achieve noise objectives. Excess external
capacitance may cause regulation problems, degraded transient response
and possible oscillation or instability.
<1.5° C/sec
Preheating Zone
240 sec max
0
0
30
60
90
120
150
Time (sec)
180
210
240
270
300
High trace = normal upper limit
Low trace - normal lower limit
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 7 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
PERFORMANCE DATA, OKL-T/6-W5
Efficiency vs. Line Voltage and Load Current @ +25°C (VOUT = 3.3V)
Maximum Current Temperature Derating at Sea Level
(VIN= 5V, VOUT = 3.3V).
100
99
7
6
5
4
3
2
1
0
Natural convection
98
97
VIN = 4V
96
VIN = 5V
VIN = 5.5V
95
94
93
0
2
4
6
Load Current (Amps)
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
Ambient Temperature (ºC)
Output Ripple and Noise (Vin=5V, Vout=3.3V, Iout=6A, ScopeBW=100MHz)
On/Off Enable Startup (Vin=5V, Vout=3.3V, Iout=6A, Cload=0)
Trace 4=Enable, Trace2=Vout
Step Load Transient Response (Vin=5V, Vout=3.3V, Iout=6A to 3A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
Step Load Transient Response (Vin=5V, Vout=3.3V, Iout=3A to 6A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 8 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
PERFORMANCE DATA, OKL-T/6-W5
Efficiency vs. Line Voltage and Load Current @ +25°C (VOUT = 2.5V)
Maximum Current Temperature Derating at Sea Level
(VIN= 5V, VOUT = 2.5V).
100
98
7
6
5
4
3
2
1
0
Natural convection
96
VIN = 3V
VIN = 5V
94
92
90
VIN = 5.5V
0
2
4
6
Load Current (Amps)
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
Ambient Temperature (ºC)
Output Ripple and Noise (Vin=5V, Vout=2.5V, Iout=6A, ScopeBW=100MHz)
On/Off Enable Startup (Vin=5V, Vout=2.5V, Iout=6A, Cload=0)
Trace 4=Enable, Trace2=Vout
Step Load Transient Response (Vin=5V, Vout=2.5V, Iout=6A to 3A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
Step Load Transient Response (Vin=5V, Vout=2.5V, Iout=3A to 6A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 9 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
PERFORMANCE DATA, OKL-T/6-W5
Efficiency vs. Line Voltage and Load Current @ +25°C (VOUT = 1.8V)
Maximum Current Temperature Derating at Sea Level
(VIN= 5V, VOUT = 1.8V).
98
96
94
7
6
5
4
3
2
1
0
Natural convection
92
90
88
86
VIN = 2.4V
VIN = 5V
VIN = 5.5V
0
2
4
6
Load Current (Amps)
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
Ambient Temperature (ºC)
Output Ripple and Noise (Vin=5V, Vout=1.8V, Iout=6A, ScopeBW=100MHz)
On/Off Enable Startup (Vin=5V, Vout=1.8V, Iout=6A, Cload=0)
Trace 4=Enable, Trace2=Vout
Step Load Transient Response (Vin=5V, Vout=1.8V, Iout=6A to 3A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
Step Load Transient Response (Vin=5V, Vout=1.8V, Iout=3A to 6A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 10 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
PERFORMANCE DATA, OKL-T/6-W5
Efficiency vs. Line Voltage and Load Current @ +25°C (VOUT = 1.5V)
Maximum Current Temperature Derating at Sea Level
(VIN= 5V, VOUT = 1.5V).
98
96
94
7
6
5
4
3
2
1
0
Natural convection
92
VIN = 2.4V
90
VIN = 5V
VIN = 5.5V
88
86
84
0
2
4
6
Load Current (Amps)
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
Ambient Temperature (ºC)
Output Ripple and Noise (Vin=5V, Vout=1.5V, Iout=6A, ScopeBW=100MHz)
On/Off Enable Startup (Vin=5V, Vout=1.5V, Iout=6A, Cload=0)
Trace 4=Enable, Trace2=Vout
Step Load Transient Response (Vin=5V, Vout=1.5V, Iout=6A to 3A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
Step Load Transient Response (Vin=5V, Vout=1.5V, Iout=3A to 6A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 11 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
PERFORMANCE DATA, OKL-T/6-W5
Efficiency vs. Line Voltage and Load Current @ +25°C (VOUT = 1.2V)
Maximum Current Temperature Derating at Sea Level
(VIN= 5V, VOUT = 1.2V).
96
94
92
7
6
5
4
3
2
1
0
Natural convection
90
VIN = 2.4V
88
VIN = 5V
VIN = 5.5V
86
84
82
0
2
4
6
Load Current (Amps)
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
Ambient Temperature (ºC)
Output Ripple and Noise (Vin=5V, Vout=1.2V, Iout=6A, ScopeBW=100MHz)
On/Off Enable Startup (Vin=5V, Vout=1.2V, Iout=6A, Cload=0)
Trace 4=Enable, Trace2=Vout
Step Load Transient Response (Vin=5V, Vout=1.2V, Iout=6A to 3A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
Step Load Transient Response (Vin=5V, Vout=1.2V, Iout=3A to 6A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 12 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
PERFORMANCE DATA, OKL-T/6-W5
Efficiency vs. Line Voltage and Load Current @ +25°C (VOUT = 1.0V)
Maximum Current Temperature Derating at Sea Level
(VIN= 5V, VOUT = 1.0V).
7
6
5
4
3
2
1
0
93
88
Natural convection
VIN = 2.4V
VIN = 5V
VIN = 5.5V
83
78
0
2
4
6
Load Current (Amps)
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
Ambient Temperature (ºC)
Output Ripple and Noise (Vin=5V, Vout=1.0V, Iout=6A, ScopeBW=100MHz)
On/Off Enable Startup (Vin=5V, Vout=1.0V, Iout=6A, Cload=0)
Trace 4=Enable, Trace2=Vout
Step Load Transient Response (Vin=5V, Vout=1.0V, Iout=6A to 3A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
Step Load Transient Response (Vin=5V, Vout=1.0V, Iout=3A to 6A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 13 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
PERFORMANCE DATA, OKL-T/6-W5
Efficiency vs. Line Voltage and Load Current @ +25°C (VOUT = 0.6V)
Maximum Current Temperature Derating at Sea Level
(VIN= 5V, VOUT = 0.6V).
90
85
7
6
5
4
3
2
1
0
Natural convection
80
75
70
VIN = 2.4V
VIN = 5V
VIN = 5.5V
0
2
4
6
Load Current (Amps)
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
Ambient Temperature (ºC)
Output Ripple and Noise (Vin=5V, Vout=0.6V, Iout=6A, ScopeBW=100MHz)
On/Off Enable Startup (Vin=5V, Vout=0.6V, Iout=6A, Cload=0)
Trace 4=Enable, Trace2=Vout
Step Load Transient Response (Vin=5V, Vout=0.6V, Iout=6A to 3A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
Step Load Transient Response (Vin=5V, Vout=0.6V, Iout=3A to 6A)
Trace 2=Vout, 200 mV/div. Trace 4=Iout, 5A/div.
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 14 of 15
OKL-T/6-W5 Series
Programmable Output 6-Amp iLGA SMT PoLs
TAPE AND REEL INFORMATION
Tape Detail
7.40 0.1
Round
Sprocket
Holes
2.00 0.1
4.00 0.1
0.40 0.05
+0.1
ø1.50
-0
16.00 0.1
B’
B
A
Vacuum Pickup
Point in Center
A’
Pulling direction
12.60 0.1
(7.0º)
Notes
1) The radius (R) is 0.3mm max.
2) Cumulative tolerance of 10 pitches of the sprocket hole is 0.2mm.
A-A’ SECTION
Reel Detail
Reel diameter 330.2
Start of
pocket tape
A
End of modules
C
B
Start of
Start of
modules
cover tape
in pockets
Reel Information (400 units per reel)
Hub diameter 13.00
Inner diameter 101.6
Key
A
Description
Length (mm)
800 40
All dimensions are in millimeters.
Tape trailer (no modules)
B
Pocket tape length before modules
Cover tape length before pocket tape
200 min.
C
240 40
www.murata-ps.com
email: sales@murata-ps.com
13 May 2010 MDC_OKL-T/6-W5 Series.A02 Page 15 of 15
相关型号：
©2020 ICPDF网 联系我们和版权申明