RCE7U2J153J4K1H03B_技术文档

Reference Specification

Leaded MLCC for Automotive with AEC-Q200

RCE Series

Product specifications in this catalog are as of Apr. 2022, and are subject to change or

obsolescence without notice.

Please consult the approval sheet before ordering.Please read rating and Cautions first.

Reference only

CAUTION

1. OPERATING VOLTAGE

When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p

value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the

voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be generated

for a transit period because of resonance or switching. Be sure to use a capacitor within rated voltage

containing these irregular voltage.

When DC-rated capacitors are to be used in input circuits from commercial power source (AC filter),

be sure to use Safety Recognized Capacitors because various regulations on withstand voltage or

impulse withstand established for each equipment should be taken into considerations.

Voltage

DC Voltage

DC+AC Voltage

AC Voltage

Pulse Voltage(1)

Pulse Voltage(2)

Positional

Vo-p

Vp-p

Vo-p

Vp-p

Measurement

2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT

Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range.

Be sure to take into account the heat generated by the capacitor itself.

When the capacitor is used in a high-frequency current, pulse current or the like, it may have the self-

generated heat due to dielectric-loss. In case of Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.),

applied voltage should be the load such as self-generated heat is within 20 °C on the condition of

atmosphere temperature 25 °C. Please contact us if self-generated heat is occurred with Class 1

capacitors (Temp.Char. : C0G,U2J,X8G, etc.). When measuring, use a thermocouple of small thermal

capacity-K of Φ0.1mm and be in the condition where capacitor is not affected by radiant heat of other

components and wind of surroundings. Excessive heat may lead to deterioration of the capacitor’s

characteristics and reliability.

3. FAIL-SAFE

Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that

may be caused by the abnormal function or the failure of our product.

4. OPERATING AND STORAGE ENVIRONMENT

The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store

capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the

like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify

that these processes do not affect product quality by testing the performance of a cleaned, bonded or

molded product in the intended equipment. Store the capacitors where the temperature and relative

humidity do not exceed 5 to 40 °C and 20 to 70%. Use capacitors within 6 months.

5. VIBRATION AND IMPACT

Do not expose a capacitor or its leads to excessive shock or vibration during use.

6. SOLDERING

When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the

capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may

result in thermal shocks that can crack the ceramic element.

7. BONDING AND RESIN MOLDING, RESIN COAT

In case of bonding, molding or coating this product, verify that these processes do not affect the quality

of capacitor by testing the performance of a bonded or molded product in the intended equipment.

In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins

containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer

coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short

circuit.

The variation in thickness of adhesive or molding resin may cause a outer coating resin cracking and/or

ceramic element cracking of a capacitor in a temperature cycling.

8. TREATMENT AFTER BONDING AND RESIN MOLDING, RESIN COAT

When the outer coating is hot (over 100 °C) after soldering, it becomes soft and fragile.

So please be careful not to give it mechanical stress.

EGLEDMNO03

1/16

Reference only

Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial

dispersion when the product is used.

9. LIMITATION OF APPLICATIONS

Please contact us before using our products for the applications listed below which require especially

high reliability for the prevention of defects which might directly cause damage to the third party’s life,

body or property.

1. Aircraft equipment

2. Aerospace equipment

3. Undersea equipment

5. Medical equipment

7. Traffic signal equipment

4. Power plant control equipment

6. Transportation equipment (vehicles, trains, ships, etc.)

8. Disaster prevention / crime prevention equipment

9. Data-processing equipment exerting influence on public

10. Application of similar complexity and/or reliability requirements to the applications listed in the above.

NOTICE

1. CLEANING (ULTRASONIC CLEANING)

To perform ultrasonic cleaning, observe the following conditions.

Rinse bath capacity : Output of 20 watts per liter or less.

Rinsing time : 5 min maximum.

Do not vibrate the PCB/PWB directly.

Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires.

2. SOLDERING AND MOUNTING

Insertion of the Lead Wire

• When soldering, insert the lead wire into the PCB without mechanically stressing the lead wire.

• Insert the lead wire into the PCB with a distance appropriate to the lead space.

3. CAPACITANCE CHANGE OF CAPACITORS

• Class 2 capacitors (Temp.Char. : X7R,X7S,X8L etc.)

Class 2 capacitors an aging characteristic, whereby the capacitor continually decreases its capacitance

slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on

a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant

circuit.

Please contact us if you need a detail information.

NOTE

1. Please make sure that your product has been evaluated in view of your specifications with our product

being mounted to your product.

2. You are requested not to use our product deviating from this specification.

EGLEDMNO03

2/16

Reference only

1. Application

This specification is applied to Leaded MLCC RCE series in accordance with

AEC-Q200 requirements used for Automotive Electronic equipment.

2. Rating

• Part Number Configuration

RCE

7U

2E

101

J

1

K1

Dimension Lead

(LxW) Style

H03

B

ex.)

Series

Temperature

Characteristics

Rated

Voltage

Capacitance

Tolerance

Individual

Specification

Package

• Temperature Characteristics

Code Temp. Char.

Standard

Temp.

Operating

Temp. Range

Temp.coef.

U2J

7U

-55～25°C

25～125°C

-750+120/-347ppm/°C

-750+/-120ppm/°C

25°C

-55～125°C

(EIA code)

• Rated Voltage

Code

2E

2J

Rated voltage

DC250V

DC630V

DC1000V

3A

• Capacitance

The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.

ex.) In case of 101

10×10¹= 100pF

• Capacitance Tolerance

Code

J

Capacitance Tolerance

+/-5%

• Dimension (LxW)

Please refer to [ Part number list ].

• Lead Style

*Lead wire is "solder coated CP wire".

Code

B1

Lead Style

Straight type

Lead spacing (mm)

5.0+/-0.8

E1

K1

Straight taping type

Inside crimp type

5.0+0.6/-0.2

5.0+/-0.8

M1

Inside crimp taping type

5.0+0.6/-0.2

• Individual Specification

Murata’s control code.

Please refer to [ Part number list ].

• Package

Code

A

B

Package

Taping type of Ammo

Bulk type

TEIKAKU

3/16

Reference only

3. Marking

Temp. char.

:

Letter code : U (U2J Char.)

Actual numbers (Less than 100pF)

3 digit numbers (100pF and over)

Code

Letter code : 4 (DC250V. Except dimension code : 1)

Letter code : 7 (DC630V)

Capacitance

Capacitance tolerance

Rated voltage

:

Letter code : A (DC1000V)

Company name code

:

Abbreviation :

(Except dimension code : 1)

(Ex.)

Rated voltage

DC250V

DC630V

DC1000V

Dimension code

1

U

102J

－

102

JAU

103

J4U

472

J7U

2

3,4

5

473

J4U

103

J7U

472

JAU

103

JAU

333

J7U

－

TEIKAKU

4/16

Reference only

4. Part number list

Unit : mm

DC

Dimension (mm)

W1

5.0

Dimension Pack

Customer

Part Number

Rated

Volt.

(V)

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

qty.

Lead Style (pcs)

L

W

F

T

RCE7U2E101J1K1H03B

RCE7U2E151J1K1H03B

RCE7U2E221J1K1H03B

RCE7U2E331J1K1H03B

RCE7U2E471J1K1H03B

RCE7U2E681J1K1H03B

RCE7U2E102J1K1H03B

RCE7U2E152J1K1H03B

RCE7U2E222J1K1H03B

RCE7U2E332J1K1H03B

RCE7U2E472J1K1H03B

RCE7U2E682J2K1H03B

RCE7U2E103J2K1H03B

RCE7U2J100J2K1H03B

RCE7U2J150J2K1H03B

RCE7U2J220J2K1H03B

RCE7U2J330J2K1H03B

RCE7U2J470J2K1H03B

RCE7U2J680J2K1H03B

RCE7U2J101J2K1H03B

RCE7U2J151J2K1H03B

RCE7U2J221J2K1H03B

RCE7U2J331J2K1H03B

RCE7U2J471J2K1H03B

RCE7U2J681J2K1H03B

RCE7U2J102J2K1H03B

RCE7U2J152J2K1H03B

RCE7U2J222J2K1H03B

RCE7U2J332J2K1H03B

RCE7U2J472J2K1H03B

RCE7U2J682J3K1H03B

RCE7U2J103J3K1H03B

RCE7U2J153J4K1H03B

RCE7U2J223J4K1H03B

RCE7U2J333J5B1H03B

RCE7U2J473J5B1H03B

U2J

250

100pF

150pF

±5%

4.0

3.5

5.0 3.15

1K1

2K1

3K1

4K1

5B1

500

4.0

5.5

7.5

3.5

4.0

5.0

5.5

8.0

5.0

6.0

7.5

8.0

-

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

250 10000pF

630

10pF

15pF

22pF

33pF

47pF

68pF

100pF

150pF

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

5.0

4.0

630 10000pF

630 15000pF

630 22000pF

630 33000pF

630 47000pF

-

PNLIST

5/16

Reference only

Unit : mm

DC

Dimension (mm)

W1

6.0

Dimension Pack

Customer

Part Number

Rated

Volt.

(V)

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

qty.

Lead Style (pcs)

L

W

F

T

RCE7U3A100J2K1H03B

RCE7U3A150J2K1H03B

RCE7U3A220J2K1H03B

RCE7U3A330J2K1H03B

RCE7U3A470J2K1H03B

RCE7U3A680J2K1H03B

RCE7U3A101J2K1H03B

RCE7U3A151J2K1H03B

RCE7U3A221J2K1H03B

RCE7U3A331J2K1H03B

RCE7U3A471J2K1H03B

RCE7U3A681J2K1H03B

RCE7U3A102J2K1H03B

RCE7U3A152J3K1H03B

RCE7U3A222J3K1H03B

RCE7U3A332J4K1H03B

RCE7U3A472J4K1H03B

RCE7U3A682J5B1H03B

RCE7U3A103J5B1H03B

U2J 1000

10pF

±5%

5.5

4.0

5.0 3.15

2K1

3K1

4K1

5B1

500

15pF

22pF

5.5

7.5

4.0

5.0

5.5

8.0

6.0

7.5

8.0

-

33pF

47pF

68pF

100pF

150pF

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

5.0

4.0

U2J 1000 10000pF

-

PNLIST

6/16

Reference only

Unit : mm

DC

Rated

Volt.

(V)

Dimension (mm)

W1

5.0

Dimension Pack

Customer

Part Number

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

Lead Style (pcs)

H/H0

qty.

L

W

F

T

RCE7U2E101J1M1H03A U2J 250

RCE7U2E151J1M1H03A U2J 250

RCE7U2E221J1M1H03A U2J 250

RCE7U2E331J1M1H03A U2J 250

RCE7U2E471J1M1H03A U2J 250

RCE7U2E681J1M1H03A U2J 250

RCE7U2E102J1M1H03A U2J 250

RCE7U2E152J1M1H03A U2J 250

RCE7U2E222J1M1H03A U2J 250

RCE7U2E332J1M1H03A U2J 250

RCE7U2E472J1M1H03A U2J 250

RCE7U2E682J2M1H03A U2J 250

100pF

150pF

±5%

4.0

5.5

7.5

3.5

5.0 3.15 16.0

1M1

2M1

3M1

4M1

5E1

2000

1500

3.5

4.0

5.0

5.5

8.0

5.0

6.0

7.5

8.0

-

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

RCE7U2E103J2M1H03A U2J

RCE7U2J100J2M1H03A U2J

RCE7U2J150J2M1H03A U2J

RCE7U2J220J2M1H03A U2J

RCE7U2J330J2M1H03A U2J

RCE7U2J470J2M1H03A U2J

RCE7U2J680J2M1H03A U2J

250 10000pF

630

10pF

15pF

22pF

33pF

47pF

68pF

RCE7U2J101J2M1H03A U2J 630

100pF

150pF

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

RCE7U2J151J2M1H03A U2J

RCE7U2J221J2M1H03A U2J

630

RCE7U2J331J2M1H03A U2J 630

RCE7U2J471J2M1H03A U2J 630

RCE7U2J681J2M1H03A U2J 630

RCE7U2J102J2M1H03A U2J

RCE7U2J152J2M1H03A U2J

RCE7U2J222J2M1H03A U2J

RCE7U2J332J2M1H03A U2J

RCE7U2J472J2M1H03A U2J

RCE7U2J682J3M1H03A U2J

RCE7U2J103J3M1H03A U2J

RCE7U2J153J4M1H03A U2J

RCE7U2J223J4M1H03A U2J

RCE7U2J333J5E1H03A U2J

RCE7U2J473J5E1H03A U2J

630

5.0

4.0 16.0

4.0 17.5

630 10000pF

630 15000pF

630 22000pF

630 33000pF

630 47000pF

-

PNLIST

7/16

Reference only

Unit : mm

DC

Rated

Volt.

(V)

Dimension (mm)

W1

6.0

Dimension Pack

Customer

Part Number

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

Lead Style (pcs)

H/H0

qty.

L

W

F

T

RCE7U3A100J2M1H03A U2J 1000

RCE7U3A150J2M1H03A U2J 1000

RCE7U3A220J2M1H03A U2J 1000

RCE7U3A330J2M1H03A U2J 1000

RCE7U3A470J2M1H03A U2J 1000

RCE7U3A680J2M1H03A U2J 1000

RCE7U3A101J2M1H03A U2J 1000

RCE7U3A151J2M1H03A U2J 1000

RCE7U3A221J2M1H03A U2J 1000

RCE7U3A331J2M1H03A U2J 1000

RCE7U3A471J2M1H03A U2J 1000

RCE7U3A681J2M1H03A U2J 1000

RCE7U3A102J2M1H03A U2J 1000

RCE7U3A152J3M1H03A U2J 1000

RCE7U3A222J3M1H03A U2J 1000

RCE7U3A332J4M1H03A U2J 1000

RCE7U3A472J4M1H03A U2J 1000

RCE7U3A682J5E1H03A U2J 1000

10pF

±5%

5.5

7.5

4.0

5.0 3.15 16.0

2M1

3M1

4M1

5E1

2000

1500

15pF

22pF

4.0

5.0

5.5

8.0

6.0

7.5

8.0

-

33pF

47pF

68pF

100pF

150pF

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

5.0

4.0 16.0

4.0 17.5

RCE7U3A103J5E1H03A U2J 1000 10000pF

-

PNLIST

8/16

Reference only

5. AEC-Q200 Murata Standard Specifications and Test Methods

AEC-Q200

No.

Specification

AEC-Q200 Test Method

Test Item

Pre-and Post-Stress

Electrical Test

1

-

2

3

4

High

Appearance

No defects or abnormalities.

Sit the capacitor for 1000±12h at 150±3°C. Let sit for 24±2h at

*room condition, then measure.

Temperature Capacitance Within ±3% or ±0.3pF

Exposure

(Storage)

Change

Q

(Whichever is larger)

30pF ≦ C : Q ≧ 350

10pF ≦ C < 30pF : Q ≧ 275+5C/2

10pF > C : Q ≧ 200+10C

C : Nominal Capacitance (pF)

More than 1,000MΩ or 50 MΩ・μF

(Whichever is smaller)

I.R.

Temperature Appearance

No defects or abnormalities.

Perform the 1000 cycles according to the four heat treatments listed in

the following table. Let sit for 24±2 h at *room condition, then measure.

Cycling

Capacitance Within ±5% or ±0.5pF

Change

Q

(Whichever is larger)

Step

1

2

3

4

30pF ≦ C : Q ≧ 350

Temp.

(°C)

Room

Temp.

Room

Temp.

10pF ≦ C < 30pF : Q ≧ 275+5C/2

10pF > C : Q ≧ 200+10C

-55+0/-3

125+3/-0

Time

(min.)

15±3

1

15±3

1

C : Nominal Capacitance (pF)

1,000MΩ or 50MΩ・μF min.

(Whichever is smaller)

I.R.

Moisture

Appearance

No defects or abnormalities

Apply the 24h heat (25 to 65°C) and humidity (80 to 98%)

treatment shown below, 10 consecutive times.

Resistance

Capacitance Within ±5% or ± 0.5pF

Change

Q

(Whichever is larger)

Let sit for 24±2 h at *room condition, then measure.

30pF ≦ C : Q ≧ 200

30pF > C : Q ≧ 100+10C/3

C : Nominal Capacitance (pF)

500MΩ or 25MΩ・μF min.

(Whichever is smaller)

I.R.

5

Biased

Appearance

No defects or abnormalities

Apply the rated voltage and DC1.3+0.2/-0V (add 100kΩ resistor)

at 85±3°C and 80 to 85% humidity for 1000±12h.

Humidity

Capacitance Within ±5% or ± 0.5pF

Change

Q

(Whichever is larger)

Remove and let sit for 24±2 h at *room condition, then measure.

The charge/discharge current is less than 50mA.

30pF ≦ C : Q ≧ 200

30pF > C : Q ≧ 100+10C/3

C : Nominal Capacitance (pF)

500MΩ or 25MΩ・μF min.

(Whichever is smaller)

I.R.

* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa

ESRCE04D

9/16

Reference only

AEC-Q200

Test Item

No.

6

Specification

AEC-Q200 Test Method

Operational

Life

Appearance

No defects or abnormalities.

Apply voltage in Table for 1000±12h at 125±3°C.

Let sit for 24±2 h at *room condition, then measure.

The charge/discharge current is less than 50mA.

Capacitance Within ±3% or ±0.3pF

Change

Q

(Whichever is larger)

30pF ≦ C : Q ≧ 350

Rated Voltage

DC250V

Test Voltage

10pF ≦ C < 30pF : Q ≧ 275+5C/2

10pF > C : Q ≧ 200+10C

150% of the rated voltage

DC630V

120% of the rated voltage

DC1000V

C : Nominal Capacitance (pF)

1,000MΩ or 50MΩ・μF min.

(Whichever is smaller)

I.R.

External Visual

7

8

9

No defects or abnormalities.

Within the specified dimensions.

To be easily legible.

Visual inspection.

Physical Dimension

Marking

Using calipers and micrometers.

Visual inspection.

10 Resistance

to Solvents

Appearance

No defects or abnormalities.

Per MIL-STD-202 Method 215

Capacitance Within the specified tolerance.

Solvent 1 : 1 part (by volume) of isopropyl alcohol

3 parts (by volume) of mineral spirits

Q

30pF ≦ C : Q ≧ 1,000

30pF > C : Q ≧ 400+20C

Solvent 2 : Terpene defluxer

Solvent 3 : 42 parts (by volume) of water

1 part (by volume) of propylene glycol

C : Nominal Capacitance (pF)

More than 10,000MΩ or 500 MΩ・μF

(Whichever is smaller)

I.R.

monomethyl ether

1 part (by volume) of monoethanolamine

Three shocks in each direction should be applied along 3

mutually perpendicular axes of the test specimen (18 shocks).

The specified test pulse should be Half-sine and should have a

duration : 0.5ms, peak value : 1500G and velocity change : 4.7m/s.

11 Mechanical

Shock

Appearance

No defects or abnormalities.

Capacitance Within the specified tolerance.

Q

30pF ≦ C : Q ≧ 1,000

30pF > C : Q ≧ 400+20C

C : Nominal Capacitance (pF)

No defects or abnormalities.

12 Vibration

Appearance

The capacitor should be subjected to a simple harmonic motion

having a total amplitude of 1.5mm, the frequency being varied

uniformly between the approximate limits of 10 and 2,000Hz.

The frequency range, from 10 to 2000Hz and return to 10Hz,

should be traversed in approximately 20 min. This motion

should be applied for 12 items in each 3 mutually perpendicular

directions (total of 36 times).

Capacitance Within the specified tolerance.

Q

30pF ≦ C : Q ≧ 1,000

30pF > C : Q ≧ 400+20C

C : Nominal Capacitance (pF)

13-1 Resistance

to

Appearance

No defects or abnormalities.

The lead wires should be immersed in the melted solder 1.5 to 2.0mm

from the root of terminal at 260±5°C for 10±1 seconds.

• Post-treatment

Capacitance Within ±2.5% or ±0.25pF

Soldering

Heat

Change

(Whichever is larger)

No defects

Dielectric

Strength

Capacitor should be stored for 24±2 hours at *room condition.

(Non-

Preheat)

(Between

terminals)

Appearance

13-2 Resistance

to

No defects or abnormalities.

First the capacitor should be stored at 120+0/-5°C for 60+0/-5 seconds.

Then, the lead wires should be immersed in the melted solder 1.5 to

2.0mm from the root of terminal at 260±5°C for 7.5+0/-1 seconds.

Capacitance Within ±2.5% or ±0.25pF

Soldering

Heat

Change

(Whichever is larger)

No defects

Dielectric

Strength

(On-

• Post-treatment

Preheat)

(Between

terminals)

Appearance

Capacitor should be stored for 24±2 hours at *room condition.

13-3 Resistance

to

No defects or abnormalities.

Test condition

Capacitance Within ±2.5% or ±0.25pF

Temperature of iron-tip : 350±10°C

Soldering time : 3.5±0.5 seconds

Soldering position

Soldering

Heat

Change

Dielectric

Strength

(Whichever is larger)

No defects

(soldering

Straight Lead : 1.5 to 2.0mm from the root of terminal.

Crimp Lead : 1.5 to 2.0mm from the end of lead bend.

iron method) (Between

terminals)

• Post-treatment

Capacitor should be stored for 24±2 hours at *room condition.

Perform the 300 cycles according to the two heat treatments listed in the

following table (Maximum transfer time is 20s.). Let sit for 24±2 h at

*room condition, then measure.

14 Thermal

Shock

Appearance

No defects or abnormalities.

Capacitance Within ±5% or ±0.5pF

Change

Q

(Whichever is larger)

30pF ≦ C : Q ≧ 350

Step

1

2

10pF ≦ C < 30pF : Q ≧ 275+5C/2

10pF > C : Q ≧ 200+10C

Temp.

(°C)

-55+0/-3

125+3/-0

Time

(min.)

C : Nominal Capacitance (pF)

1,000MΩ or 50MΩ・μF min.

(Whichever is smaller)

15±3

I.R.

* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa

ESRCE04D

10/16

Reference only

AEC-Q200

Test Item

No.

Specifications

AEC-Q200 Test Method

No defects or abnormalities.

Within the specified tolerance.

30pF ≦ C : Q ≧ 1,000

15 ESD

Appearance

Per AEC-Q200-002

Capacitance

Q

30pF > C : Q ≧ 400+20C

C : Nominal Capacitance (pF)

More than 10,000MΩ or 500MΩ・μF

(Whichever is smaller)

I.R.

Lead wire should be soldered with uniform

coating on the axial direction over 95% of

the circumferential direction.

16 Solderability

Should be placed into steam aging for 8h±15 min.

The terminal of capacitor is dipped into a solution of ethanol

(JIS K 8101) and rosin (JIS K 5902) (25% rosin in weight

propotion). Immerse in solder solution for 2±0.5 seconds.

In both cases the depth of dipping is up to about 1.5 to 2mm from the

terminal body.

Temp. of solder :

245±5°C Lead Free Solder (Sn-3.0Ag-0.5Cu)

235±5°C H60A or H63A Eutectic Solder

Visual inspection.

No defects or abnormalities.

Within the specified tolerance.

30pF ≦ C : Q ≧ 1,000

17 Electrical

Characte-

rization

Appearance

Capacitance

Q

The capacitance, Q should be measured at 25°C at the frequency and

voltage shown in the table.

30pF > C : Q ≧ 400+20C

Nominal Cap. Frequency

C ≦ 1000pF 1±0.1MHz AC0.5 to 5V(r.m.s.)

C > 1000pF 1±0.1kHz AC1±0.2V(r.m.s.)

Voltage

C : Nominal Capacitance (pF)

I.R.

Between 10,000MΩ or 500MΩ・μF min.

The insulation resistance should be measured with DC500V

(DC250V in case of rated voltage : DC250V) at 25 °C within 2 min.

of charging.

Terminals (Whichever is smaller)

Dielectric

Strength

Between No defects or abnormalities.

Terminals

The capacitor should not be damaged when voltage in Table is

applied between the terminations for 1 to 5 seconds.

(Charge/Discharge current ≦ 50mA.)

Rated Voltage

DC250V

Test Voltage

200% of the rated voltage

150% of the rated voltage

130% of the rated voltage

DC630V

DC1000V

Body

No defects or abnormalities.

The capacitor is placed in a container with metal balls of 1mm

diameter so that each terminal, short-circuit is kept approximately

2mm from the balls, and 200% of the rated DC voltage (130% of the

rated voltage in case of rated voltage : DC630V,DC1000V) is impressed

for 1 to 5 seconds between capacitor terminals and metal balls.

(Charge/Discharge current ≦ 50mA.)

Insulation

Termination not to be broken or loosened.

18 Terminal

Strength

Tensile

As in the figure, fix the capacitor body, apply the force gradually

to each lead in the radial direction of the capacitor until reaching 10N

and then keep the force applied for 10±1 seconds.

Strength

F

Termination not to be broken or loosened.

Bending

Strength

Each lead wire should be subjected to a force of 2.5N and then

be bent 90° at the point of egress in one direction. Each wire is then

returned to the original position and bent 90° in the opposite

direction at the rate of one bend per 2 to 3 seconds.

The capacitance change should be measured after 5min. at

each specified temperature step.

Capacitance

Temperature

Characteristics

Within the specified Tolerance

19

25°C to 125°C : -750±120 ppm/°C

-55°C to 25°C : -750+120/-347 ppm/°C

Step

Temperature(°C)

25±2

1

2

3

4

5

-55±3

25±2

125±3

25±2

The temperature coefficient is determined using the capacitance

measured in step 3 as a reference. When cycling the temperature

sequentially from step 1 through 5 (-55°C to 125°C)

the capacitance should be within the specified tolerance for the

temperature coefficient and capacitance change as Table A.

The capacitance drift is calculated by dividing the differences

between the maximum and minimum measured values in the step

1, 3 and 5 by the capacitance value in step 3.

* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa

ESRCE04D

11/16

Reference only

6. Packing specification

・Bulk type (Packing style code : B)

The size of packing case and packing way

Polyethylene bag

Partition

270 max.

125 max.

Unit : mm

340 max.

The number of packing = ^*1Packing quantity × ^*2n

*1 : Please refer to [Part number list].

*2 : Standard n = 20 (bag)

Note)

The outer package and the number of outer packing be changed by the order getting amount.

JKBCRPE02

12/16

Reference only

・Ammo pack taping type (Packing style code : A)

A crease is made every 25 pitches, and the tape with capacitors is packed zigzag into a case.

When body of the capacitor is piled on other body under it.

The size of packing case and packing way

240 max.

Position of label

340 max.

Unit : mm

51 max.

Hold down tape

Capacitor

Base tape

Hold down

tape upper

EKTRPE01

13/16

Reference only

7. Taping specification

7-1. Dimension of capacitors on tape

Straight taping type < Lead Style : E1 >

Pitch of component 12.7mm / Lead spacing 5.0mm

0

P2

P

△h2

△h1

Marking

△S

e

P1

F

φd

φD0

P0

Unit : mm

Item

Code

Dimensions

Remarks

Pitch of component

P

P0

F

12.7+/-1.0

12.7+/-0.2

5.0+0.6/-0.2

Pitch of sprocket hole

Lead spacing

Length from hole center to component

center

P2

6.35+/-1.3

Deviation of progress direction

They include deviation by lead bend

Deviation of tape width direction

Length from hole center to lead

Deviation along tape, left or right defect

Carrier tape width

P1

∆S

W

3.85+/-0.7

0+/-2.0

18.0+/-0.5

9.0+0/-0.5

17.5+/-0.5

0.5 max.

4.0+/-0.1

0.5+/-0.05

0.6+/-0.3

1.5 max.

Position of sprocket hole

For straight lead type

W1

H

Protrusion length

Diameter of sprocket hole

Lead diameter

ΦD0

Φd

t1

Total tape thickness

They include hold down tape

thickness.

Total thickness of tape and lead wire

t2

2.0 max.（Dimension code：U）

1.0 max.（except as above）

11.0+0/-1.0

∆h1

∆h2

L

Deviation across tape

Portion to cut in case of defect

Hold down tape width

W0

W2

9.5 min.

Hold down tape position

1.5+/-1.5

2.0 max.（Dimension code：U）

1.5 max.（except as above）

Coating extension on lead

e

ETP1E101B

14/16

Reference only

Inside crimp taping type < Lead Style : M1 >

Pitch of component 12.7mm / Lead spacing 5.0mm

0

P2

P

Δh1

Marking

Δh2

ΔS

e

P1

F

Φd

ΦD0

P0

Unit : mm

Item

Code

P

Dimensions

12.7+/-1.0

12.7+/-0.2

5.0+0.6/-0.2

Remarks

Pitch of component

Pitch of sprocket hole

Lead spacing

P0

F

Length from hole center to component

center

P2

6.35+/-1.3

Deviation of progress direction

They include deviation by lead bend

Deviation of tape width direction

Length from hole center to lead

Deviation along tape, left or right defect

Carrier tape width

P1

ΔS

W

3.85+/-0.7

0+/-2.0

18.0+/-0.5

9.0+0/-0.5

Position of sprocket hole

W1

Lead distance between reference and

bottom plane

H0

16.0+/-0.5

Protrusion length

0.5 max.

4.0+/-0.1

0.5+/-0.05

0.6+/-0.3

1.5 max.

Diameter of sprocket hole

Lead diameter

ΦD0

Φd

t1

Total tape thickness

They include hold down tape

thickness

Total thickness of tape and lead wire

t2

ꢀꢀꢀ2.0 max. (Dimension code : W)

ꢀꢀꢀ1.0 max. (except as above)

11.0+0/-1.0

Δh1

Δh2

L

Deviation across tape

Portion to cut in case of defect

Hold down tape width

W0

W2

e

9.5 min.

Hold down tape position

Coating extension on lead

1.5+/-1.5

Up to the end of crimp

ETP1M101A

15/16

Reference only

ꢀꢀ7-2. Splicing way of tape

1) Adhesive force of tape is over 3N at test condition as below.

W

Hold down tape

Base tape

2) Splicing of tape

ꢀꢀꢀa) When base tape is spliced

•Base tape shall be spliced by cellophane tape.

(Total tape thickness shall be less than 1.05mm.)

Progress direction

in production line

Hold down tape

Base tape

About 30 to 50

No lifting for the

Cellophane tape

direction of

progressing

Unit : mm

ꢀꢀꢀb) When hold down tape is spliced

ꢀꢀꢀ •Hold down tape shall be spliced with overlapping.

(Total tape thickness shall be less than 1.05mm.)

20 to 30

Hold down tape

Base tape

Unit : mm

Progress direction

in production line

ꢀꢀꢀc) When both tape are spliced

•Base tape and hold down tape shall be spliced with splicing tape.

ETP2R01

16/16


型号：	RCE7U2J153J4K1H03B
厂家：	muRata
描述：	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] 医疗医疗器械
文件：	总17页 (文件大小：707K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

RCE7U2J153J4K1H03B [MURATA]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E