RDE7U3A470J2K1H03B_技术文档

Reference Specification

Leaded MLCC for General Purpose

RDE Series

Product specifications in this catalog are as of Mar. 2022, and are subject to change or

obsolescence without notice.

Please consult the approval sheet before ordering.Please read rating and Cautions first.

Reference only

CAUTION

1. OPERATING VOLTAGE

When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p

value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the

voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be generated

for a transit period because of resonance or switching. Be sure to use a capacitor within rated voltage

containing these irregular voltage.

When DC-rated capacitors are to be used in input circuits from commercial power source (AC filter),

be sure to use Safety Recognized Capacitors because various regulations on withstand voltage or

impulse withstand established for each equipment should be taken into considerations.

Voltage

DC Voltage

DC+AC Voltage

AC Voltage

Pulse Voltage(1)

Pulse Voltage(2)

Positional

Vo-p

Vp-p

Vo-p

Vp-p

Measurement

2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT

Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range.

Be sure to take into account the heat generated by the capacitor itself.

When the capacitor is used in a high-frequency current, pulse current or the like, it may have the self-

generated heat due to dielectric-loss. In case of Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.),

applied voltage should be the load such as self-generated heat is within 20 °C on the condition of

atmosphere temperature 25 °C. Please contact us if self-generated heat is occurred with Class 1

capacitors (Temp.Char. : C0G,U2J,X8G, etc.). When measuring, use a thermocouple of small thermal

capacity-K of Φ0.1mm and be in the condition where capacitor is not affected by radiant heat of other

components and wind of surroundings. Excessive heat may lead to deterioration of the capacitor’s

characteristics and reliability.

3. FAIL-SAFE

Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that

may be caused by the abnormal function or the failure of our product.

4. OPERATING AND STORAGE ENVIRONMENT

The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store

capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the

like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify

that these processes do not affect product quality by testing the performance of a cleaned, bonded or

molded product in the intended equipment. Store the capacitors where the temperature and relative

humidity do not exceed 5 to 40 °C and 20 to 70%. Use capacitors within 6 months.

5. VIBRATION AND IMPACT

Do not expose a capacitor or its leads to excessive shock or vibration during use.

6. SOLDERING

When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the

capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may

result in thermal shocks that can crack the ceramic element.

7. BONDING AND RESIN MOLDING, RESIN COAT

In case of bonding, molding or coating this product, verify that these processes do not affect the quality

of capacitor by testing the performance of a bonded or molded product in the intended equipment.

In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins

containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer

coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short

circuit.

The variation in thickness of adhesive or molding resin may cause a outer coating resin cracking and/or

ceramic element cracking of a capacitor in a temperature cycling.

8. TREATMENT AFTER BONDING AND RESIN MOLDING, RESIN COAT

When the outer coating is hot (over 100 °C) after soldering, it becomes soft and fragile.

So please be careful not to give it mechanical stress.

EGLEDMNO03

1/18

Reference only

Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial

dispersion when the product is used.

9. LIMITATION OF APPLICATIONS

Please contact us before using our products for the applications listed below which require especially

high reliability for the prevention of defects which might directly cause damage to the third party’s life,

body or property.

1. Aircraft equipment

2. Aerospace equipment

3. Undersea equipment

5. Medical equipment

7. Traffic signal equipment

4. Power plant control equipment

6. Transportation equipment (vehicles, trains, ships, etc.)

8. Disaster prevention / crime prevention equipment

9. Data-processing equipment exerting influence on public

10. Application of similar complexity and/or reliability requirements to the applications listed in the above.

NOTICE

1. CLEANING (ULTRASONIC CLEANING)

To perform ultrasonic cleaning, observe the following conditions.

Rinse bath capacity : Output of 20 watts per liter or less.

Rinsing time : 5 min maximum.

Do not vibrate the PCB/PWB directly.

Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires.

2. SOLDERING AND MOUNTING

Insertion of the Lead Wire

• When soldering, insert the lead wire into the PCB without mechanically stressing the lead wire.

• Insert the lead wire into the PCB with a distance appropriate to the lead space.

3. CAPACITANCE CHANGE OF CAPACITORS

• Class 2 capacitors (Temp.Char. : X7R,X7S,X8L etc.)

Class 2 capacitors an aging characteristic, whereby the capacitor continually decreases its capacitance

slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on

a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant

circuit.

Please contact us if you need a detail information.

NOTE

1. Please make sure that your product has been evaluated in view of your specifications with our product

being mounted to your product.

2. You are requested not to use our product deviating from this specification.

EGLEDMNO03

2/18

Reference only

1. Application

This product specification is applied to Leaded MLCC RDE series used

for General Electronic equipment.

Do not use these products in any automotive power train or safety

equipmentꢀincluding battery chargers for electric vehicles and plug-in hybrids.

2. Rating

• Part Number Configuration

RDE

7U

2E

101

J

1

K1

H03

B

ex.)

Series

Temperature

Characteristics

Rated

Voltage

Capacitance

Tolerance

Dimension Lead

Individual

Specification

Package

(LxW)

Style

• Temperature Characteristics

Standard

Temp.

Operating

Temp. Range

Code Temp. Char.

Temp. Range

Temp.coef.

U2J

7U

-55～25°C

25～125°C

-750+120/-347ppm/°C

-750+/-120ppm/°C

25°C

-55～125°C

(EIA code)

• Rated Voltage

Code

2E

2J

Rated voltage

DC250V

DC630V

DC1000V

3A

• Capacitance

The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.

ex.) In case of 101

10×10¹= 100pF

• Capacitance Tolerance

Code

J

Capacitance Tolerance

+/-5%

• Dimension (LxW)

Please refer to [ Part number list ].

• Lead Style

*Lead wire is "solder coated CP wire".

Code

B1

Lead Style

Straight type

Lead spacing (mm)

5.0+/-0.8

E1

K1

Straight taping type

Inside crimp type

5.0+0.6/-0.2

5.0+/-0.8

M1

Inside crimp taping type

5.0+0.6/-0.2

• Individual Specification

Murata’s control code.

Please refer to [ Part number list ].

• Package

Code

A

B

Package

Taping type of Ammo

Bulk type

TEIKAKU

3/18

Reference only

3. Marking

Temp. char.

:

Letter code : U (U2J Char.)

Actual numbers (Less than 100pF)

3 digit numbers (100pF and over)

Code

Letter code : 4 (DC250V. Except dimension code : 1)

Letter code : 7 (DC630V)

Capacitance

Capacitance tolerance

Rated voltage

:

Letter code : A (DC1000V)

Company name code

:

Abbreviation :

(Except dimension code : 1)

(Ex.)

Rated voltage

DC250V

DC630V

DC1000V

Dimension code

1

U

102J

－

102

JAU

103

J4U

472

J7U

2

103

J7U

472

JAU

473

J4U

3,4

5,U

103

JAU

333

J7U

－

TEIKAKU

4/18

Reference only

4. Part number list

Unit : mm

DC

Dimension (mm)

W1

5.0

Dimension Pack

Customer

Part Number

Rated

Volt.

(V)

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

qty.

Lead Style (pcs)

L

W

F

T

RDE7U2E101J1K1H03B

RDE7U2E151J1K1H03B

RDE7U2E221J1K1H03B

RDE7U2E331J1K1H03B

RDE7U2E471J1K1H03B

RDE7U2E681J1K1H03B

RDE7U2E102J1K1H03B

RDE7U2E152J1K1H03B

RDE7U2E222J1K1H03B

RDE7U2E332J1K1H03B

RDE7U2E472J1K1H03B

RDE7U2E682J2K1H03B

RDE7U2E103J2K1H03B

RDE7U2E153J2K1H03B

RDE7U2E223J2K1H03B

RDE7U2E333J3K1H03B

RDE7U2E473J3K1H03B

RDE7U2J100J2K1H03B

RDE7U2J150J2K1H03B

RDE7U2J220J2K1H03B

RDE7U2J330J2K1H03B

RDE7U2J470J2K1H03B

RDE7U2J680J2K1H03B

RDE7U2J101J2K1H03B

RDE7U2J151J2K1H03B

RDE7U2J221J2K1H03B

RDE7U2J331J2K1H03B

RDE7U2J471J2K1H03B

RDE7U2J681J2K1H03B

RDE7U2J102J2K1H03B

RDE7U2J152J2K1H03B

RDE7U2J222J2K1H03B

RDE7U2J332J2K1H03B

RDE7U2J472J2K1H03B

RDE7U2J682J3K1H03B

RDE7U2J103J3K1H03B

RDE7U2J153J4K1H03B

RDE7U2J223J4K1H03B

RDE7U2J333J5B1H03B

RDE7U2J473J5B1H03B

U2J

250

100pF

150pF

±5%

4.5

3.5

5.0 3.15

1K1

2K1

3K1

2K1

3K1

4K1

5B1

500

4.5

5.5

7.5

3.5

4.0

5.0

4.0

5.0

5.5

8.0

5.0

6.0

7.5

6.0

7.5

8.0

-

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

250 10000pF

250 15000pF

250 22000pF

250 33000pF

250 47000pF

5.0

4.0

630

10pF

15pF

5.0 3.15

22pF

33pF

47pF

68pF

100pF

150pF

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

5.0

4.0

4.5

630 10000pF

630 15000pF

630 22000pF

630 33000pF

630 47000pF

-

PNLIST

5/18

Reference only

Unit : mm

DC

Dimension (mm)

W1

Dimension Pack

Customer

Part Number

Rated

Volt.

(V)

Cap.

Tol.

Murata Part Number

T.C.

U2J

Cap.

(LxW)

qty.

Lead Style (pcs)

L

W

F

T

RDE7U2J943JUB1H03B

RDE7U3A100J2K1H03B

RDE7U3A150J2K1H03B

RDE7U3A220J2K1H03B

RDE7U3A330J2K1H03B

RDE7U3A470J2K1H03B

RDE7U3A680J2K1H03B

RDE7U3A101J2K1H03B

RDE7U3A151J2K1H03B

RDE7U3A221J2K1H03B

RDE7U3A331J2K1H03B

RDE7U3A471J2K1H03B

RDE7U3A681J2K1H03B

RDE7U3A102J2K1H03B

RDE7U3A152J3K1H03B

RDE7U3A222J3K1H03B

RDE7U3A332J4K1H03B

RDE7U3A472J4K1H03B

630 94000pF

±5%

7.7 13.0

-

5.0

4.0

UB1

2K1

3K1

4K1

200

500

U2J 1000

10pF

15pF

5.5

7.5

4.0

5.0

5.5

6.0

7.5

8.0

5.0 3.15

22pF

33pF

47pF

68pF

100pF

150pF

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

5.0

4.0

PNLIST

6/18

Reference only

Unit : mm

DC

Dimension (mm)

W1

Dimension Pack

Customer

Part Number

Rated

Volt.

(V)

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

qty.

Lead Style (pcs)

L

W

F

T

RDE7U3A682J5B1H03B

RDE7U3A103J5B1H03B

RDE7U3A203JUB1H03B

U2J 1000

6800pF

±5%

7.5

7.7 13.0

8.0

-

5.0

4.5

5B1

UB1

500

200

U2J 1000 10000pF

U2J 1000 20000pF

8.0

5.0

4.5

4.0

PNLIST

7/18

Reference only

Unit : mm

DC

Rated

Volt.

(V)

Dimension (mm)

W1

5.0

Dimension Pack

Customer

Part Number

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

Lead Style (pcs)

H/H0

qty.

L

W

F

T

RDE7U2E101J1M1H03A U2J

RDE7U2E151J1M1H03A U2J

RDE7U2E221J1M1H03A U2J

RDE7U2E331J1M1H03A U2J

RDE7U2E471J1M1H03A U2J

RDE7U2E681J1M1H03A U2J

RDE7U2E102J1M1H03A U2J

RDE7U2E152J1M1H03A U2J

RDE7U2E222J1M1H03A U2J

RDE7U2E332J1M1H03A U2J

RDE7U2E472J1M1H03A U2J

RDE7U2E682J2M1H03A U2J

RDE7U2E103J2M1H03A U2J

RDE7U2E153J2M1H03A U2J

RDE7U2E223J2M1H03A U2J

RDE7U2E333J3M1H03A U2J

RDE7U2E473J3M1H03A U2J

RDE7U2J100J2M1H03A U2J

RDE7U2J150J2M1H03A U2J

RDE7U2J220J2M1H03A U2J

RDE7U2J330J2M1H03A U2J

RDE7U2J470J2M1H03A U2J

RDE7U2J680J2M1H03A U2J

RDE7U2J101J2M1H03A U2J

RDE7U2J151J2M1H03A U2J

RDE7U2J221J2M1H03A U2J

RDE7U2J331J2M1H03A U2J

RDE7U2J471J2M1H03A U2J

RDE7U2J681J2M1H03A U2J

RDE7U2J102J2M1H03A U2J

RDE7U2J152J2M1H03A U2J

RDE7U2J222J2M1H03A U2J

RDE7U2J332J2M1H03A U2J

RDE7U2J472J2M1H03A U2J

RDE7U2J682J3M1H03A U2J

RDE7U2J103J3M1H03A U2J

RDE7U2J153J4M1H03A U2J

RDE7U2J223J4M1H03A U2J

250

100pF

150pF

±5%

4.5

5.5

7.5

3.5

5.0 3.15 16.0

1M1

2M1

3M1

2M1

3M1

4M1

5E1

2000

1500

3.5

4.0

5.0

4.0

5.0

5.5

8.0

5.0

6.0

7.5

6.0

7.5

8.0

-

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

250 10000pF

250 15000pF

250 22000pF

250 33000pF

250 47000pF

5.0

4.0 16.0

630

10pF

15pF

5.0 3.15 16.0

22pF

33pF

47pF

68pF

100pF

150pF

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

6800pF

5.0

4.0 16.0

4.5 17.5

630 10000pF

630 15000pF

630 22000pF

RDE7U2J333J5E1H03A U2J 630 33000pF

RDE7U2J473J5E1H03A U2J 630 47000pF

-

PNLIST

8/18

Reference only

Unit : mm

DC

Rated

Volt.

(V)

Dimension (mm)

Dimension Pack

Customer

Part Number

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

qty.

Lead Style (pcs)

L

W

W1

F

T

H/H0

RDE7U2J943JUE1H03A U2J

630 94000pF

±5%

7.7 13.0

-

5.0

4.0 17.5

UE1

2M1

3M1

4M1

1500

2000

1500

RDE7U3A100J2M1H03A U2J 1000

RDE7U3A150J2M1H03A U2J 1000

RDE7U3A220J2M1H03A U2J 1000

RDE7U3A330J2M1H03A U2J 1000

RDE7U3A470J2M1H03A U2J 1000

RDE7U3A680J2M1H03A U2J 1000

RDE7U3A101J2M1H03A U2J 1000

RDE7U3A151J2M1H03A U2J 1000

RDE7U3A221J2M1H03A U2J 1000

RDE7U3A331J2M1H03A U2J 1000

RDE7U3A471J2M1H03A U2J 1000

RDE7U3A681J2M1H03A U2J 1000

RDE7U3A102J2M1H03A U2J 1000

RDE7U3A152J3M1H03A U2J 1000

RDE7U3A222J3M1H03A U2J 1000

RDE7U3A332J4M1H03A U2J 1000

RDE7U3A472J4M1H03A U2J 1000

10pF

15pF

5.5

7.5

4.0

5.0

5.5

6.0

7.5

8.0

5.0 3.15 16.0

22pF

33pF

47pF

68pF

100pF

150pF

220pF

330pF

470pF

680pF

1000pF

1500pF

2200pF

3300pF

4700pF

5.0

4.0 16.0

PNLIST

9/18

Reference only

Unit : mm

DC

Rated

Volt.

(V)

Dimension (mm)

Dimension Pack

Customer

Part Number

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

Lead Style (pcs)

H/H0

qty.

L

W

W1

F

T

RDE7U3A682J5E1H03A U2J 1000

6800pF

±5%

7.5

8.0

-

5.0

4.5 17.5

4.0 17.5

5E1

UE1

1500

RDE7U3A103J5E1H03A U2J 1000 10000pF

RDE7U3A203JUE1H03A U2J 1000 20000pF

7.7 13.0

PNLIST

10/18

Reference only

5.SPECIFICATIONS AND TEST METHODS

No.

1

Item

Specification

Test Method

Appearance

No defects or abnormalities.

Visual inspection.

2

Dimension and

Marking

Within the specified dimensions and

Marking.

Visual inspection, Using Caliper.

3

Dielectric

Between

No defects or abnormalities.

The capacitor should not be damaged when voltage of in Table is

applied between theꢀterminations for 1 to 5 seconds.

(Charge/Discharge current ≦ 50mA.)

Strength

Terminals

Rated voltage

DC250V

Test voltage

200% of the rated voltage

150% of the rated voltage

130% of the rated voltage

DC630V

DC1kV

Body

No defects or abnormalities.

The capacitor is placed in a container with metal balls

of 1mm diameter so that each terminal, short-circuit,

is kept approximately 2mm from the balls, and voltage in Table is

impressed for 1 to 5 seconds between capacitor terminals and

metal balls.

Insulation

(Charge/Discharge current ≦ 50mA.)

Rated voltage

DC250V

Test voltage

DC500V

DC630V・DC1kV

DC1300V

4

Insulation

Resistance

(I.R.)

Between

10,000MΩ or 500MΩ・μF min.

The insulation resistance should be measured with

DC500±50V (DC250±25V in case of rated voltage : DC250V) at normal

temperature and humidity and within 2 minutes of charging.

(Charge/Discharge current ≦ 50mA.)

Terminals

(Whichever is smaller)

5

6

Capacitance

Q

Within the specified tolerance.

The capacitance, Q should be measured at 25°C

at the frequency and voltage shown in the table.

30pF ≦ C : Q ≧ 1,000

Nominal Cap. Frequency

Voltage

1±0.2MHz AC0.5 to 5V(r.m.s.)

1±0.2kHz AC1±0.2V(r.m.s.)

30pF > C : Q ≧ 400+20C

C≦1000pF

C > 1000pF

C : Nominal Capacitance (pF)

7

Capacitance

Temperature

Characteristics

Within the specified Tolerance.

25°C to 125°C : -750±120 ppm/°C

-55°C to 25°C : -750+120/-347 ppm/°C

The capacitance change should be measured after 5

minutes at each specified temperature stage.

The temperature coefficient is determined using the

capacitance measured in step 3 as a reference.

When cycling the temperature sequentially from step

1 through 5 (-55°C to 125°C) the capacitance should

be within the specified tolerance for the temperature coefficient.

Step

Temperature(°C)

25±2

1

2

3

4

5

-55±3

25±2

125±3

25±2

8

Terminal

Strength

Tensile

Termination not to be broken or loosened.

No defects or abnormalities.

As in the figure, fix the capacitor body,

Strength

apply the force gradually to each

lead in the radial direction of the

F

capacitor until reaching 10N and then

keep applied the force for 10±1 seconds.

Bending

Strength

Each lead wire should be subjected to a force of

2.5N and then be bent 90° at the point of egress in

one direction. Each wire is then returned to the

original position and bent 90° in the opposite

direction at the rate of one bend per 2 to 3 seconds.

The capacitor should be subjected to a simple

harmonic motion having a total amplitude of 1.5mm,

the frequency being varied uniformly between the

approximate limits of 10Hz and 55Hz. The frequency

range, from 10Hz to 55Hz and return to 10Hz, shall be

traversed in approximately 1 minute. This motion

shall be applied for a period of 2 hours in each 3

mutually perpendicular directions (total of 6 hours).

9

Vibration

Appearance

Resistance

Capacitance Within the specified tolerance.

Q

30pF ≦ C : Q ≧ 1,000

30pF > C : Q ≧ 400+20C

C : Nominal Capacitance (pF)

ESRDE111A

11/18

Reference only

No.

Item

Specification

Test Method

The terminal of capacitor is dipped into a solution of

ethanol (JIS K 8101) and rosin (JIS K 5902) (25%

rosin in weight propotion). Immerse in solder solution

for 2±0.5 seconds. In both cases the depth of dipping

is up to about 1.5 to 2mm from the terminal body.

Temp. of solder :

10 Solderability of Lead

Solder is deposited on unintermittently

immersed portion in axial direction

covering 3/4 or more in circumferential

direction ofꢀlead wires.

245±5°C Lead Free Solder (Sn-3.0Ag-0.5Cu)

235±5°C H60A or H63A Eutectic Solder

11-1 Resistance

Appearance

No defects or abnormalities.

The lead wires should be immersed in the melted solder 1.5 to 2.0mm

from the root of terminal at 260±5°C for 10±1 seconds.

to

Capacitance Within ±2.5% or ±0.25pF

Soldering

Change

(Whichever is larger)

No defects

Heat

Dielectric

Strength

• Post-treatment

(Non-

Capacitor should be stored for 24±2 hours at *room condition.

Preheat)

(Between

terminals)

Appearance

11-2 Resistance

to

No defects or abnormalities.

First the capacitor should be stored at 120+0/-5°C for 60+0/-5 seconds.

Then, the lead wires should be immersed in the melted solder

Capacitance Within ±2.5% or ±0.25pF

Soldering

Heat

Change

(Whichever is larger)

No defects

1.5 to 2.0mm from the root of terminal at 260±5°C for 7.5+0/-1 seconds.

Dielectric

(On-Preheat) Strength

(Between

• Post-treatment

Capacitor should be stored for 24±2 hours at *room condition.

terminals)

11-3 Resistance

Appearance

No defects or abnormalities.

Test condition

to

Capacitance Within ±2.5% or ±0.25pF

Temperature of iron-tip : 350±10°C

Soldering time : 3.5±0.5 seconds

Soldering position

Soldering

Change

(Whichever is larger)

No defects

Heat

Dielectric

Strength

(Between

terminals)

(soldering

iron method)

Straight Lead : 1.5 to 2.0mm from the root of terminal.

Crimp Lead : 1.5 to 2.0mm from the end of lead bend.

• Post-treatment

Capacitor should be stored for 24±2 hours at *room condition.

Repeat 5 cycles according to the 4 heatꢀtreatments listed in the

following table.

12 Temperature Appearance

No defects or abnormalities.

Cycle

Capacitance Within ±5% or ±0.5pF

Change

Q

(Whichever is larger)

Set at *room condition for 24±2 hours, then measure.

30pF ≦ C : Q ≧ 350

Step

1

2

3

4

10pF ≦ C < 30pF : Q ≧ 275+5C/2

10pF > C : Q ≧ 200+10C

Min.

Operating

Temp. ±3

Max.

Operating

Temp. ±3

Temp.

(°C)

Room

Temp.

Room

Temp.

C : Nominal Capacitance (pF)

1,000MΩ or 50MΩ・μF min.

(Whichever is smaller)

Time

(min.)

I.R.

30±3

3 max.

30±3

3 max.

Dielectric

Strength

No defects or abnormalities.

(Between

Terminals)

Appearance

13 Humidity

No defects or abnormalities.

Set the capacitor at 40±2°C and relative humidity 90 to 95%

for 500+24/-0 hours.

(Steady State) Capacitance Within ±5% or ±0.5pF

Change

Q

(Whichever is larger)

Remove and set for 24±2 hours at *room condition then measure.

30pF ≦ C : Q ≧ 350

10pF ≦ C < 30pF : Q ≧ 275+5C/2

10pF > C : Q ≧ 200+10C

C : Nominal Capacitance (pF)

1,000MΩ or 50MΩ・μF min.

(Whichever is smaller)

I.R.

* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa

ESRDE111A

12/18

Reference only

No.

Item

Appearance

Specification

Test Method

14 Humidity

Load

No defects or abnormalities.

Apply the rated voltage at 40±2°C and relative

humidity of 90 to 95% for 500+24/-0 hours.

Capacitance Within ±5% or ±0.5pF

Change

Q

(Whichever is larger)

Remove and set for 24±2 hours at *room condition, then measure.

(Charge/Discharge current ≦ 50mA.)

30pF ≦ C : Q ≧ 200

30pF > C : Q ≧ 100+10C/3

C : Nominal Capacitance (pF)

500MΩ or 25MΩ・μF min.

(Whichever is smaller)

I.R.

15 High

Appearance

No defects or abnormalities.

Apply voltage in Table at the maximum

Temperature Capacitance Within ±3% or ±0.3pF

operating temperature ±3°C for 1000+48/-0 hours.

Remove and set for 24±2 hours at *room condition then measure.

(Charge/Discharge current ≦ 50mA.)

Load

Change

Q

(Whichever is larger)

30pF ≦ C : Q ≧ 350

10pF ≦ C < 30pF : Q ≧ 275+5C/2

10pF > C : Q ≧ 200+10C

Rated voltage

DC250V

Test voltage

150% of the rated voltage

DC630V, DC1kV 120% of the rated voltage

C : Nominal Capacitance (pF)

1,000MΩ or 50MΩ・μF min.

(Whichever is smaller)

No defects or abnormalities.

Legible

I.R.

16 Solvent

Appearance

Marking

The capacitor should be fully immersed, unagitated,

in reagent at 20 to 25°C for 30±5 seconds and then

remove gently. Marking on the surface of the

Resistance

capacitor shall immediately be visually examined.

Regent : Isopropyl alcohol

* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa

ESRDE111A

13/18

Reference only

6. Packing specification

・Bulk type (Packing style code : B)

The size of packing case and packing way

Polyethylene bag

Partition

270 max.

125 max.

Unit : mm

340 max.

The number of packing = ^*1Packing quantity × ^*2n

*1 : Please refer to [Part number list].

*2 : Standard n = 20 (bag)

Note)

The outer package and the number of outer packing be changed by the order getting amount.

JKBCRPE02

14/18

Reference only

・Ammo pack taping type (Packing style code : A)

ꢀꢀꢀꢀꢀꢀA crease is made every 25 pitches, and the tape with capacitors is packed zigzag into a case.

ꢀꢀꢀꢀꢀꢀWhen body of the capacitor is piled on other body under it.

The size of packing case and packing way

240 max.

Position of label

340 max.

Unit : mm

51 max.

Hold down tape

Capacitor

Base tape

Hold down

tape upper

EKTRPE01

15/18

Reference only

7. Taping specification

7-1. Dimension of capacitors on tape

Straight taping type < Lead code : E1 >

Pitch of component 12.7mm / Lead spacing 5.0mm

0

P2

P

△h2

△h1

Marking

△S

e

P1

F

φd

φD0

P0

Unit : mm

Item

Code

Dimensions

Remarks

Pitch of component

P

P0

F

12.7+/-1.0

12.7+/-0.2

5.0+0.6/-0.2

Pitch of sprocket hole

Lead spacing

Length from hole center to component

center

P2

6.35+/-1.3

Deviation of progress direction

They include deviation by lead bend

Deviation of tape width direction

Length from hole center to lead

Deviation along tape, left or right defect

Carrier tape width

P1

∆S

W

3.85+/-0.7

0+/-2.0

18.0+/-0.5

9.0+0/-0.5

17.5+/-0.5

0.5 max.

4.0+/-0.1

0.5+/-0.05

0.6+/-0.3

1.5 max.

Position of sprocket hole

For straight lead type

W1

H

Protrusion length

Diameter of sprocket hole

Lead diameter

ΦD0

Φd

t1

Total tape thickness

They include hold down tape

thickness.

Total thickness of tape and lead wire

t2

2.0 max.（Dimension code：U）

1.0 max.（except as above）

11.0+0/-1.0

∆h1

∆h2

L

Deviation across tape

Portion to cut in case of defect

Hold down tape width

W0

W2

9.5 min.

Hold down tape position

1.5+/-1.5

2.0 max.（Dimension code：U）

1.5 max.（except as above）

Coating extension on lead

e

ETP1E101A

16/18

Reference only

Inside crimp taping type < Lead code : M1 >

Pitch of component 12.7mm / Lead spacing 5.0mm

0

P2

P

Δh1

Marking

Δh2

ΔS

e

P1

F

Φd

ΦD0

P0

Unit : mm

Item

Code

P

Dimensions

12.7+/-1.0

12.7+/-0.2

5.0+0.6/-0.2

Remarks

Pitch of component

Pitch of sprocket hole

Lead spacing

P0

F

Length from hole center to component

center

P2

6.35+/-1.3

Deviation of progress direction

They include deviation by lead bend

Deviation of tape width direction

Length from hole center to lead

Deviation along tape, left or right defect

Carrier tape width

P1

ΔS

W

3.85+/-0.7

0+/-2.0

18.0+/-0.5

9.0+0/-0.5

Position of sprocket hole

W1

Lead distance between reference and

bottom plane

H0

16.0+/-0.5

Protrusion length

0.5 max.

4.0+/-0.1

0.5+/-0.05

0.6+/-0.3

1.5 max.

Diameter of sprocket hole

Lead diameter

ΦD0

Φd

t1

Total tape thickness

They include hold down tape

thickness

Total thickness of tape and lead wire

t2

2.0 max. (Dimension code : W)

1.0 max. (except as above)

11.0+0/-1.0

Δh1

Δh2

L

Deviation across tape

Portion to cut in case of defect

Hold down tape width

W0

W2

e

9.5 min.

Hold down tape position

Coating extension on lead

1.5+/-1.5

Up to the end of crimp

ETP1M101

17/18

Reference only

7-2. Splicing way of tape

1) Adhesive force of tape is over 3N at test condition as below.

W

Hold down tape

Base tape

2) Splicing of tape

a) When base tape is spliced

•Base tape shall be spliced by cellophane tape.

(Total tape thickness shall be less than 1.05mm.)

Progress direction

in production line

Hold down tape

Base tape

About 30 to 50

No lifting for the

Cellophane tape

direction of

progressing

Unit : mm

b) When hold down tape is spliced

•Hold down tape shall be spliced with overlapping.

(Total tape thickness shall be less than 1.05mm.)

20 to 30

Hold down tape

Base tape

Unit : mm

Progress direction

in production line

c) When both tape are spliced

•Base tape and hold down tape shall be spliced with splicing tape.

ETP2R01

18/18


型号：	RDE7U3A470J2K1H03B
厂家：	muRata
描述：	民用设备,工业设备,移动设备,植入式以外的医疗器械设备 [GHTF A/B/C],汽车[信息娱乐 / 舒适设备] 医疗医疗器械
文件：	总19页 (文件大小：732K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

RDE7U3A470J2K1H03B [MURATA]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E