首页 |元器件品牌

RHS7G2A272J1M2H01A [MURATA]

汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C];
RHS7G2A272J1M2H01A
型号： RHS7G2A272J1M2H01A
厂家： muRata    muRata
描述：

汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C]

医疗 医疗器械
文件： 总15页 (文件大小：582K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
Reference Specification  
200℃ Operation Leaded MLCC for Automotive with AEC-Q200  
RHS Series  
Product specifications in this catalog are as of Mar. 2022, and are subject to change or  
obsolescence without notice.  
Please consult the approval sheet before ordering.Please read rating and Cautions first.  
Reference only  
ꢀꢀCAUTION  
1. OPERATING VOLTAGE  
When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p  
value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the  
voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be generated  
for a transit period because of resonance or switching. Be sure to use a capacitor within rated voltage  
containing these irregular voltage.  
When DC-rated capacitors are to be used in input circuits from commercial power source (AC filter),  
be sure to use Safety Recognized Capacitors because various regulations on withstand voltage or  
impulse withstand established for each equipment should be taken into considerations.  
Voltage  
DC Voltage  
DC+AC Voltage  
AC Voltage  
Pulse Voltage(1)  
Pulse Voltage(2)  
Positional  
Vo-p  
Vp-p  
Vo-p  
Vp-p  
Vp-p  
Measurement  
2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT  
Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range.  
Be sure to take into account the heat generated by the capacitor itself.  
When the capacitor is used in a high-frequency current, pulse current or the like, it may have the self-  
generated heat due to dielectric-loss. In case of Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.),  
applied voltage should be the load such as self-generated heat is within 20 °C on the condition of  
atmosphere temperature 25 °C. Please contact us if self-generated heat is occurred with Class 1  
capacitors (Temp.Char. : C0G,U2J,X8G, etc.). When measuring, use a thermocouple of small thermal  
capacity-K of Φ0.1mm and be in the condition where capacitor is not affected by radiant heat of other  
components and wind of surroundings. Excessive heat may lead to deterioration of the capacitor’s  
characteristics and reliability.  
3. FAIL-SAFE  
Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that  
may be caused by the abnormal function or the failure of our product.  
4. OPERATING AND STORAGE ENVIRONMENT  
The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store  
capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the  
like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify  
that these processes do not affect product quality by testing the performance of a cleaned, bonded or  
molded product in the intended equipment. Store the capacitors where the temperature and relative  
humidity do not exceed 5 to 40 °C and 20 to 70%. Use capacitors within 6 months.  
5. VIBRATION AND IMPACT  
Do not expose a capacitor or its leads to excessive shock or vibration during use.  
6. SOLDERING  
When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the  
capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may  
result in thermal shocks that can crack the ceramic element.  
7. BONDING AND RESIN MOLDING, RESIN COAT  
In case of bonding, molding or coating this product, verify that these processes do not affect the quality  
of capacitor by testing the performance of a bonded or molded product in the intended equipment.  
In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins  
containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer  
coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short  
circuit.  
The variation in thickness of adhesive or molding resin may cause a outer coating resin cracking and/or  
ceramic element cracking of a capacitor in a temperature cycling.  
8. TREATMENT AFTER BONDING AND RESIN MOLDING, RESIN COAT  
When the outer coating is hot (over 100 °C) after soldering, it becomes soft and fragile.  
So please be careful not to give it mechanical stress.  
EGLEDMNO03  
1/14  
Reference only  
Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial  
dispersion when the product is used.  
9. LIMITATION OF APPLICATIONS  
Please contact us before using our products for the applications listed below which require especially  
high reliability for the prevention of defects which might directly cause damage to the third party’s life,  
body or property.  
1. Aircraft equipment  
2. Aerospace equipment  
3. Undersea equipment  
5. Medical equipment  
7. Traffic signal equipment  
4. Power plant control equipment  
6. Transportation equipment (vehicles, trains, ships, etc.)  
8. Disaster prevention / crime prevention equipment  
9. Data-processing equipment exerting influence on public  
10. Application of similar complexity and/or reliability requirements to the applications listed in the above.  
NOTICE  
1. CLEANING (ULTRASONIC CLEANING)  
To perform ultrasonic cleaning, observe the following conditions.  
Rinse bath capacity : Output of 20 watts per liter or less.  
Rinsing time : 5 min maximum.  
Do not vibrate the PCB/PWB directly.  
Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires.  
2. SOLDERING AND MOUNTING  
Insertion of the Lead Wire  
• When soldering, insert the lead wire into the PCB without mechanically stressing the lead wire.  
• Insert the lead wire into the PCB with a distance appropriate to the lead space.  
3. CAPACITANCE CHANGE OF CAPACITORS  
• Class 2 capacitors (Temp.Char. : X7R,X7S,X8L etc.)  
Class 2 capacitors an aging characteristic, whereby the capacitor continually decreases its capacitance  
slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on  
a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant  
circuit.  
Please contact us if you need a detail information.  
ꢀꢀNOTE  
1. Please make sure that your product has been evaluated in view of your specifications with our product  
being mounted to your product.  
2. You are requested not to use our product deviating from this specification.  
EGLEDMNO03  
2/14  
Reference only  
1. Application  
This specification is applied to 200℃ Operation Leaded MLCC RHS series  
iin accordance with AEC-Q200 requirements used for Automotive Electronic equipment.  
2. Rating  
• Applied maximum temperature up to 200℃  
Note : Maximum accumulative time to 200℃ is within 2000 hours.  
• Part Number Configuration  
RHS  
7G  
2A  
101  
J
0
A2  
H01  
B
ex.)  
Series  
Temperature  
Characteristics  
Rated  
Voltage  
Capacitance  
Capacitance  
Tolerance  
Dimension Lead  
Individual  
Specification  
Package  
(LxW)  
Style  
• Series  
Code  
RHS  
Content  
Epoxy coated, 200°C max.  
• Temperature Characteristics  
Standard  
Temp.  
Operating  
Temp. Range  
Code Temp. Char.  
Temp. Range  
Temp.coef.  
-55～25°C  
25～125°C  
125～200°C  
0+30/-72ppm/°C  
0+/-30ppm/°C  
0+72/-30ppm/°C  
CCG  
7G  
25°C  
-55～200°C  
(Murata code)  
• Rated Voltage  
Code  
2A  
Rated voltage  
DC100V  
When the product temperature exceeds 150°C, please use this product  
within the voltage and temperature derated conditions in the figure below.  
TEIKAKU  
3/14  
Reference only  
• Capacitance  
The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.  
ex.) In case of 101  
10×101 = 100pF  
• Capacitance Tolerance  
Code  
J
Capacitance Tolerance  
+/-5%  
• Dimension (LxW)  
Please refer to [ Part number list ].  
• Lead Style  
*Lead wire is "solder coated CP wire".  
Code  
A2  
Lead Style  
Straight type  
Lead spacing (mm)  
2.5+/-0.8  
DG  
K1  
Straight taping type  
Inside crimp type  
2.5+0.4/-0.2  
5.0+/-0.8  
M2  
Inside crimp taping type  
5.0+0.6/-0.2  
• Individual Specification  
Murata’s control code.  
Please refer to [ Part number list ].  
• Package  
Code  
A
B
Package  
Taping type of Ammo  
Bulk type  
3. Marking  
Temp. char.  
Capacitance  
: Letter code : 4 (CCG char.)  
: 3 digit numbers  
Capacitance tolerance : Code  
(Ex.)  
Rated voltage  
DC100V  
Dimension code  
0,1  
4
101J  
TEIKAKU  
4/14  
Reference only  
4. Part number list  
Unit : mm  
DC  
Dimension (mm)  
Dimension Pack  
Customer  
Part Number  
Rated  
Volt.  
(V)  
Cap.  
Tol.  
Murata Part Number  
T.C.  
Cap.  
(LxW)  
qty.  
Lead Style (pcs)  
L
W
W1  
F
T
RHS7G2A101J0A2H01B  
RHS7G2A121J0A2H01B  
RHS7G2A151J0A2H01B  
RHS7G2A181J0A2H01B  
RHS7G2A221J0A2H01B  
RHS7G2A271J0A2H01B  
RHS7G2A331J0A2H01B  
RHS7G2A391J0A2H01B  
RHS7G2A471J0A2H01B  
RHS7G2A561J0A2H01B  
RHS7G2A681J0A2H01B  
RHS7G2A821J0A2H01B  
RHS7G2A102J0A2H01B  
RHS7G2A122J0A2H01B  
RHS7G2A152J0A2H01B  
RHS7G2A182J1A2H01B  
RHS7G2A222J1A2H01B  
RHS7G2A272J1A2H01B  
RHS7G2A332J1A2H01B  
RHS7G2A101J0K1H01B  
RHS7G2A121J0K1H01B  
RHS7G2A151J0K1H01B  
RHS7G2A181J0K1H01B  
RHS7G2A221J0K1H01B  
RHS7G2A271J0K1H01B  
RHS7G2A331J0K1H01B  
RHS7G2A391J0K1H01B  
RHS7G2A471J0K1H01B  
RHS7G2A561J0K1H01B  
RHS7G2A681J0K1H01B  
RHS7G2A821J0K1H01B  
RHS7G2A102J0K1H01B  
RHS7G2A122J0K1H01B  
RHS7G2A152J0K1H01B  
RHS7G2A182J1K1H01B  
RHS7G2A222J1K1H01B  
RHS7G2A272J1K1H01B  
RHS7G2A332J1K1H01B  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
CCG  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100pF  
120pF  
150pF  
180pF  
220pF  
270pF  
330pF  
390pF  
470pF  
560pF  
680pF  
820pF  
1000pF  
1200pF  
1500pF  
1800pF  
2200pF  
2700pF  
3300pF  
100pF  
120pF  
150pF  
180pF  
220pF  
270pF  
330pF  
390pF  
470pF  
560pF  
680pF  
820pF  
1000pF  
1200pF  
1500pF  
1800pF  
2200pF  
2700pF  
3300pF  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
3.9  
3.5  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2.5  
2.6  
0A2  
0A2  
0A2  
0A2  
0A2  
0A2  
0A2  
0A2  
0A2  
0A2  
0A2  
0A2  
0A2  
0A2  
0A2  
1A2  
1A2  
1A2  
1A2  
0K1  
0K1  
0K1  
0K1  
0K1  
0K1  
0K1  
0K1  
0K1  
0K1  
0K1  
0K1  
0K1  
0K1  
0K1  
1K1  
1K1  
1K1  
1K1  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
500  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
4.2  
4.2  
4.2  
4.2  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
4.2  
4.2  
4.2  
4.2  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.8  
2.8  
2.8  
2.8  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.6  
2.8  
2.8  
2.8  
2.8  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
5.0  
5.0  
5.0  
5.0  
PNLIST  
5/14  
Reference only  
Unit : mm  
DC  
Rated  
Volt.  
(V)  
Dimension (mm)  
Dimension Pack  
Customer  
Part Number  
Cap.  
Tol.  
Murata Part Number  
T.C.  
Cap.  
(LxW)  
Lead Style (pcs)  
H/H0  
qty.  
L
W
W1  
F
T
RHS7G2A101J0DGH01A CCG 100  
RHS7G2A121J0DGH01A CCG 100  
RHS7G2A151J0DGH01A CCG 100  
RHS7G2A181J0DGH01A CCG 100  
RHS7G2A221J0DGH01A CCG 100  
RHS7G2A271J0DGH01A CCG 100  
RHS7G2A331J0DGH01A CCG 100  
RHS7G2A391J0DGH01A CCG 100  
RHS7G2A471J0DGH01A CCG 100  
RHS7G2A561J0DGH01A CCG 100  
RHS7G2A681J0DGH01A CCG 100  
RHS7G2A821J0DGH01A CCG 100  
RHS7G2A102J0DGH01A CCG 100  
RHS7G2A122J0DGH01A CCG 100  
RHS7G2A152J0DGH01A CCG 100  
RHS7G2A182J1DGH01A CCG 100  
RHS7G2A222J1DGH01A CCG 100  
RHS7G2A272J1DGH01A CCG 100  
RHS7G2A332J1DGH01A CCG 100  
RHS7G2A101J0M2H01A CCG 100  
RHS7G2A121J0M2H01A CCG 100  
RHS7G2A151J0M2H01A CCG 100  
RHS7G2A181J0M2H01A CCG 100  
RHS7G2A221J0M2H01A CCG 100  
RHS7G2A271J0M2H01A CCG 100  
RHS7G2A331J0M2H01A CCG 100  
RHS7G2A391J0M2H01A CCG 100  
RHS7G2A471J0M2H01A CCG 100  
RHS7G2A561J0M2H01A CCG 100  
RHS7G2A681J0M2H01A CCG 100  
RHS7G2A821J0M2H01A CCG 100  
RHS7G2A102J0M2H01A CCG 100  
RHS7G2A122J0M2H01A CCG 100  
RHS7G2A152J0M2H01A CCG 100  
RHS7G2A182J1M2H01A CCG 100  
RHS7G2A222J1M2H01A CCG 100  
RHS7G2A272J1M2H01A CCG 100  
RHS7G2A332J1M2H01A CCG 100  
100pF  
120pF  
150pF  
180pF  
220pF  
270pF  
330pF  
390pF  
470pF  
560pF  
680pF  
820pF  
1000pF  
1200pF  
1500pF  
1800pF  
2200pF  
2700pF  
3300pF  
100pF  
120pF  
150pF  
180pF  
220pF  
270pF  
330pF  
390pF  
470pF  
560pF  
680pF  
820pF  
1000pF  
1200pF  
1500pF  
1800pF  
2200pF  
2700pF  
3300pF  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
±5%  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
4.2  
4.2  
4.2  
4.2  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
4.2  
4.2  
4.2  
4.2  
3.5  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.8 20.0  
2.8 20.0  
2.8 20.0  
2.8 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.6 20.0  
2.8 20.0  
2.8 20.0  
2.8 20.0  
2.8 20.0  
0DG  
0DG  
0DG  
0DG  
0DG  
0DG  
0DG  
0DG  
0DG  
0DG  
0DG  
0DG  
0DG  
0DG  
0DG  
1DG  
1DG  
1DG  
1DG  
0M2  
0M2  
0M2  
0M2  
0M2  
0M2  
0M2  
0M2  
0M2  
0M2  
0M2  
0M2  
0M2  
0M2  
0M2  
1M2  
1M2  
1M2  
1M2  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
2000  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
3.5  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
6.0  
5.0  
5.0  
5.0  
5.0  
PNLIST  
6/14  
Reference only  
5. AEC-Q200 Murata Standard Specifications and Test Methods  
AEC-Q200  
No.  
Specification  
AEC-Q200 Test Method  
Test Item  
Pre-and Post-Stress  
Electrical Test  
1
-
2
High  
Appearance  
No defects or abnormalities except color  
change of outer coating.  
Sit the capacitor for 1000±12 hours at 200±5°C. Let sit for 24±2 hours  
at *room condition, then measure.  
Temperature  
Exposure  
(Storage)  
Capacitance Within ±3% or ±0.3pF  
Change  
Q
(Whichever is larger)  
Q ≧ 350  
I.R.  
1,000MΩ min.  
3
Temperature Appearance  
Cycling  
No defects or abnormalities except color  
change of outer coating  
Perform the 1000 cycles according to the four heat treatments listed in  
the following table. Let sit for 24±2 hours at *room condition, then measure.  
Capacitance Within ±5% or ±0.5pF  
Step  
1
2
3
4
Change  
Q
(Whichever is larger)  
Q ≧ 350  
Temp.  
(°C)  
Room  
Temp.  
Room  
Temp.  
-55+0/-3  
200+5/-0  
I.R.  
1,000MΩ min.  
Time  
15±3  
1
15±3  
1
(min.)  
4
Moisture  
Appearance  
No defects or abnormalities.  
Apply the 24 hours heat (25 to 65°C) and humidity (80 to 98%)  
treatment shown below, 10 consecutive times.  
Resistance  
Capacitance Within ±5% or ± 0.5pF  
Change  
Q
(Whichever is larger)  
Q ≧ 200  
Let sit for 24±2 hours at *room condition, then measure.  
I.R.  
500MΩ min.  
5
6
Biased  
Appearance  
No defects or abnormalities.  
Apply the rated voltage and DC1.3+0.2/-0V (add 100kΩ resistor)  
at 85±3°C and 80 to 85% humidity for 1000±12 hours.  
Remove and let sit for 24±2 hours at *room condition, then measure.  
The charge/discharge current is less than 50mA.  
Humidity  
Capacitance Within ±5% or ± 0.5pF  
Change  
Q
(Whichever is larger)  
Q ≧ 200  
I.R.  
500MΩ min.  
Operational  
Life  
Appearance  
No defects or abnormalities except color  
change of outer coating.  
Apply voltage in Table for 1,000±12h at 200±5°C.  
Let sit for 24±2 hours at *room condition, then measure.  
The charge/discharge current is less than 50mA.  
Capacitance Within ±3% or ±0.3pF  
Change  
Q
(Whichever is larger)  
Q ≧ 350  
Capacitance  
100pF-1000pF  
1200pF-3300pF  
Test Voltage  
50% of the rated voltage  
25% of the rated voltage  
I.R.  
1,000MΩ min.  
7
8
9
External Visual  
No defects or abnormalities.  
Within the specified dimensions.  
To be easily legible.  
Visual inspection.  
Physical Dimension  
Marking  
Using calipers and micrometers.  
Visual inspection.  
10 Resistance  
to Solvents  
Appearance  
No defects or abnormalities.  
Per MIL-STD-202 Method 215  
Capacitance Within the specified tolerance.  
Solvent 1 : 1 part (by volume) of isopropyl alcohol  
3 parts (by volume) of mineral spirits  
Q
Q ≧ 1,000  
I.R.  
10,000MΩ min.  
Solvent 2 : Terpene defluxer  
Solvent 3 : 42 parts (by volume) of water  
1part (by volume) of propylene glycol monomethyl ether  
1 part (by volume) of monoethanolamine  
* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa  
ESRH05C  
7/14  
Reference only  
AEC-Q200  
Test Item  
No.  
Specification  
AEC-Q200 Test Method  
11 Mechanical  
Shock  
Appearance  
No defects or abnormalities.  
Three shocks in each direction should be applied along 3  
mutually perpendicular axes of the test specimen (18 shocks).  
The specified test pulse should be Half-sine and should have a  
duration : 0.5ms, peak value : 1500G and velocity change : 4.7m/s.  
The capacitor should be subjected to a simple harmonic motion  
having a total amplitude of 1.5mm, the frequency being varied  
uniformly between the approximate limits of 10 and 2000Hz.  
The frequency range, from 10 to 2000Hz and return to 10Hz,  
should be traversed in approximately 20 min. This motion  
should be applied for 12 items in each 3 mutually perpendicular  
directions (total of 36 times).  
Capacitance Within the specified tolerance.  
Q
Q ≧ 1,000  
12 Vibration  
Appearance  
No defects or abnormalities.  
Capacitance Within the specified tolerance.  
Q
Q ≧ 1,000  
13-1 Resistance to Appearance  
No defects or abnormalities.  
The lead wires should be immersed in the melted solder 1.5 to 2.0mm  
from the root of terminal at 260±5°C for 10±1 seconds.  
Soldering  
Heat  
Capacitance Within ±2.5% or ±0.25pF  
Change  
(Whichever is larger)  
No defects.  
(Non-  
Dielectric  
Strength  
(Between  
terminals)  
• Post-treatment  
Preheat)  
Capacitor should be stored for 24±2 hours at *room condition.  
13-2 Resistance to Appearance  
No defects or abnormalities.  
First the capacitor should be stored at 120+0/-5°C for 60+0/-5 seconds.  
Then, the lead wires should be immersed in the melted solder  
Soldering  
Heat  
Capacitance Within ±2.5% or ±0.25pF  
Change  
(Whichever is larger)  
No defects.  
1.5 to 2.0mm from the root of terminal at 260±5°C for 7.5+0/-1 seconds.  
(On-  
Dielectric  
Strength  
(Between  
terminals)  
Preheat)  
• Post-treatment  
Capacitor should be stored for 24±2 hours at *room condition.  
13-3 Resistance to Appearance  
No defects or abnormalities.  
Test condition  
Soldering  
Heat  
Capacitance Within ±2.5% or ±0.25pF  
Temperature of iron-tip : 350±10°C  
Soldering time : 3.5±0.5 seconds  
Soldering position  
Change  
(Whichever is larger)  
No defects.  
(soldering  
Dielectric  
iron method) Strength  
(Between  
Straight Lead : 1.5 to 2.0mm from the root of terminal.  
Crimp Lead : 1.5 to 2.0mm from the end of lead bend.  
terminals)  
• Post-treatment  
Capacitor should be stored for 24±2 hours at *room condition.  
Perform the 300 cycles according to the two heat treatments listed in the  
following table (Maximum transfer time is 20 seconds.).  
Let sit for 24±2 hours at *room condition, then measure.  
14 Thermal  
Shock  
Appearance  
No defects or abnormalities.  
Capacitance Within ±5% or ±0.5pF  
Change  
Q
(Whichever is larger)  
Q ≧ 350  
Step  
1
2
I.R.  
1,000MΩ min.  
Temp.  
(°C)  
-55+0/-3  
200+5/-0  
Time  
(min.)  
15±3  
15±3  
15 ESD  
Appearance  
No defects or abnormalities.  
Per AEC-Q200-002  
Capacitance Within the specified tolerance.  
Q
Q ≧ 1,000  
I.R.  
10,000MΩ min.  
16 Solderability  
Lead wire should be soldered with  
uniform coating on the axial direction over  
95% of the circumferential direction.  
The terminal of a capacitor is dipped into a solution of ethanol  
(JIS-K-8101) and rosin (JIS-K-5902) (25%rosin in weight propotion) and  
then into molten solder (JIS-Z-3282) for 2±0.5 seconds. In both cases  
the depth of dipping is up to about 1.5 to 2mm from the terminal body.  
Temp. of solder :  
245±5°C Lead Free Solder (Sn-3.0Ag-0.5Cu)  
235±5°C H60A or H63A Eutectic Solder  
* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa  
ESRH05C  
8/14  
Reference only  
AEC-Q200  
Test Item  
No.  
Specifications  
AEC-Q200 Test Method  
17 Electrical  
Characte-  
rization  
Appearance  
No defects or abnormalities.  
Visual inspection.  
Capacitance Within the specified tolerance.  
The capacitance, Q should be measured at 25°C at the frequency  
and voltage shown in the table.  
Q
Q ≧ 1,000  
Nominal Cap. Frequency  
Voltage  
1±0.1MHz AC0.5 to 5V(r.m.s.)  
1±0.1kHz AC1±0.2V(r.m.s.)  
C ≦ 1000pF  
C > 1000pF  
Insulation  
Resistance  
(I.R.)  
Room  
10,000MΩ min.  
20MΩ min.  
The insulation resistance should be measured at 25±3 °C with a  
DC voltage not exceeding the rated voltage at normal temperature  
and humidity and within 2 min. of charging.  
Temperature  
(Charge/Discharge current ≦ 50mA.)  
High  
The insulation resistance should be measured at 200±5°C with a  
DC voltage not exceeding voltage in Table and within 2 min. of  
charging.  
Temperature  
(Charge/Discharge current ≦ 50mA.)  
Capacitance  
100pF-1000pF  
1200pF-3300pF  
Test Voltage  
50% of the rated voltage  
25% of the rated voltage  
Dielectric  
Strength  
Between  
No defects or abnormalities.  
The capacitor should not be damaged when voltage in Table is  
applied between the terminations for 1 to 5 seconds.  
(Charge/Discharge current ≦ 50mA.)  
Terminals  
Rated Voltage  
DC100V  
Test Voltage  
300% of the rated voltage  
Body  
No defects or abnormalities.  
The capacitor is placed in a container with  
metal balls of 1mm diameter so that each  
terminal, short-circuit, is kept approximately  
2mm from the balls as shown in the figure,  
and voltage in table is impressed for 1 to 5  
seconds between capacitor terminals and  
metal balls.  
Insulation  
Approx.  
2mm  
Metal  
balls  
(Charge/Discharge current ≦ 50mA.)  
Rated Voltage  
DC100V  
Test Voltage  
250% of the rated voltage  
18 Terminal  
Strength  
Tensile  
Termination not to be broken or loosened.  
As in the figure, fix the capacitor body, apply the force gradually  
to each lead in the radial direction of the capacitor until reaching  
10N and then keep the force applied for 10±1 seconds.  
Strength  
F
Bending  
Strength  
Termination not to be broken or loosened.  
Each lead wire should be subjected to a force of 2.5N and then  
be bent 90° at the point of egress in one direction. Each wire is  
then returned to the original position and bent 90° in the opposite  
direction at the rate of one bend per 2 to 3 seconds.  
The capacitance change should be measured after 5min. at  
each specified temperature step.  
19 Capacitance  
Temperature  
Within the specified Tolerance.  
0+30/-72ppm/°C (-55 to 25°C)  
0±30ppm/°C (25 to 125°C)  
Characteristics  
Step  
Temperature(°C)  
25±2  
0+72/-30ppm/°C (125 to 200°C)  
1
2
3
4
5
-55±3  
25±2  
200±5  
25±2  
The temperature coefficient is determined using the capacitance  
measured in step 3 as a reference. When cycling the temperature  
sequentially from step 1 through 5 (-55°C to 150°C)  
the capacitance should be within the specified tolerance for the  
temperature coefficient and capacitance change as Table A.  
The capacitance drift is calculated by dividing the differences  
between the maximum and minimum measured values in the  
step 1, 3 and 5 by the capacitance value in step 3.  
* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa  
ESRH05C  
9/14  
Reference only  
6. Packing specification  
・Bulk type (Packing style code : B)  
The size of packing case and packing way  
Polyethylene bag  
Partition  
270 max.  
125 max.  
Unit : mm  
340 max.  
The number of packing = *1 Packing quantity × *2 n  
*1 : Please refer to [Part number list].  
*2 : Standard n = 20 (bag)  
Note)  
The outer package and the number of outer packing be changed by the order getting amount.  
JKBCRPE02  
10/14  
Reference only  
・Ammo pack taping type (Packing style code : A)  
ꢀꢀꢀꢀꢀꢀA crease is made every 25 pitches, and the tape with capacitors is packed zigzag into a case.  
ꢀꢀꢀꢀꢀꢀWhen body of the capacitor is piled on other body under it.  
The size of packing case and packing way  
240 max.  
Position of label  
340 max.  
Unit : mm  
51 max.  
Hold down tape  
Capacitor  
Base tape  
Hold down  
tape upper  
EKTRPE01  
11/14  
Reference only  
7. Taping specification  
7-1. Dimension of capacitors on tape  
Straight taping type < Lead Style : DG >  
Pitch of component 12.7mm / Lead spacing 2.5mm  
P
P2  
0
△S  
△h2  
△h1  
Marking  
e
P1  
Φd  
F
ΦD0  
P0  
Unit : mm  
Item  
Code  
Dimensions  
12.7+/-1.0  
12.7+/-0.2  
2.5+0.4/-0.2  
Remarks  
Pitch of component  
P
P0  
F
Pitch of sprocket hole  
Lead spacing  
Length from hole center to component  
center  
P2  
6.35+/-1.3  
Deviation of progress direction  
They include deviation by lead bend  
Deviation of tape width direction  
Length from hole center to lead  
Deviation along tape, left or right defect  
Carrier tape width  
P1  
ΔS  
W
5.1+/-0.7  
0+/-2.0  
18.0+/-0.5  
9.0+0/-0.5  
Position of sprocket hole  
W1  
Lead distance between reference and bottom  
plane  
H
20.0+/-0.5  
Protrusion length  
0.5 max.  
4.0+/-0.1  
0.5+/-0.05  
0.6+/-0.3  
1.5 max.  
Diameter of sprocket hole  
Lead diameter  
ΦD0  
Φd  
t1  
Total tape thickness  
They include hold down tape  
thickness  
Total thickness of tape and lead wire  
t2  
Δh1  
Δh2  
L
Deviation across tape  
1.0 max.  
Portion to cut in case of defect  
Hold down tape width  
11.0+0/-1.0  
9.5 min.  
W0  
W2  
e
Hold down tape position  
Coating extension on lead  
1.5+/-1.5  
2.0 max.  
ETP1DBG01A  
12/14  
Reference only  
Inside crimp taping type < Lead Style : M2 >  
Pitch of component 12.7mm / Lead spacing 5.0mm  
Unit : mm  
Item  
Code  
P
Dimensions  
12.7+/-1.0  
12.7+/-0.2  
5.0+0.6/-0.2  
Remarks  
Pitch of component  
Pitch of sprocket hole  
Lead spacing  
P0  
F
Length from hole center to component  
center  
P2  
6.35+/-1.3  
Deviation of progress direction  
They include deviation by lead bend  
Deviation of tape width direction  
Length from hole center to lead  
Deviation along tape, left or right defect  
Carrier tape width  
P1  
ΔS  
W
3.85+/-0.7  
0+/-2.0  
18.0+/-0.5  
9.0+0/-0.5  
Position of sprocket hole  
W1  
Lead distance between reference and bottom  
plane  
H0  
20.0+/-0.5  
Protrusion length  
0.5 max.  
4.0+/-0.1  
0.5+/-0.05  
0.6+/-0.3  
1.5 max.  
Diameter of sprocket hole  
Lead diameter  
ΦD0  
Φd  
t1  
Total tape thickness  
They include hold down tape  
thickness  
Total thickness of tape and lead wire  
t2  
ꢀꢀꢀ2.0 max. (Dimension code : W)  
ꢀꢀꢀ1.0 max. (except as above)  
11.0+0/-1.0  
Δh1  
Δh2  
L
Deviation across tape  
Portion to cut in case of defect  
Hold down tape width  
W0  
W2  
e
9.5 min.  
Hold down tape position  
Coating extension on lead  
1.5+/-1.5  
Up to the end of crimp  
ETP1M201A  
13/14  
Reference only  
7-2. Splicing way of tape  
1) Adhesive force of tape is over 3N at test condition as below.  
W
Hold down tape  
Base tape  
2) Splicing of tape  
a) When base tape is spliced  
•Base tape shall be spliced by cellophane tape.  
(Total tape thickness shall be less than 1.05mm.)  
Progress direction  
in production line  
Hold down tape  
Base tape  
About 30 to 50  
No lifting for the  
Cellophane tape  
direction of  
progressing  
Unit : mm  
b) When hold down tape is spliced  
•Hold down tape shall be spliced with overlapping.  
(Total tape thickness shall be less than 1.05mm.)  
20 to 30  
Hold down tape  
Base tape  
Unit : mm  
Progress direction  
in production line  
c) When both tape are spliced  
•Base tape and hold down tape shall be spliced with splicing tape.  
ETP2R01  
14/14  

相关型号：

SI9130DB

 5- and 3.3-V Step-Down Synchronous Converters

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1-E3

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135_11

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9136_11

 Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130CG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130LG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130_11

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137DB

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137LG

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9122E

 500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification Drivers

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明