RHSQ92A153K0K1H01B [MURATA]

汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C];


型号：	RHSQ92A153K0K1H01B
厂家：	muRata
描述：	汽车[动力总成 / 安全设备],汽车[信息娱乐 / 舒适设备],植入式以外的医疗器械设备 [GHTF A/B/C] 医疗医疗器械
文件：	总15页 (文件大小：649K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Reference Specification

200℃ Operation Leaded MLCC for Automotive with AEC-Q200

RHS Series

Product specifications in this catalog are as of Mar. 2022, and are subject to change or

obsolescence without notice.

Please consult the approval sheet before ordering.Please read rating and Cautions first.

Reference only

CAUTION

1. OPERATING VOLTAGE

When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p

value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the

voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be generated

for a transit period because of resonance or switching. Be sure to use a capacitor within rated voltage

containing these irregular voltage.

When DC-rated capacitors are to be used in input circuits from commercial power source (AC filter),

be sure to use Safety Recognized Capacitors because various regulations on withstand voltage or

impulse withstand established for each equipment should be taken into considerations.

Voltage

DC Voltage

DC+AC Voltage

AC Voltage

Pulse Voltage(1)

Pulse Voltage(2)

Positional

Vo-p

Vp-p

Vo-p

Vp-p

Measurement

2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT

Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range.

Be sure to take into account the heat generated by the capacitor itself.

When the capacitor is used in a high-frequency current, pulse current or the like, it may have the self-

generated heat due to dielectric-loss. In case of Class 2 capacitors (Temp.Char. : X7R,X7S,X8L, etc.),

applied voltage should be the load such as self-generated heat is within 20 °C on the condition of

atmosphere temperature 25 °C. Please contact us if self-generated heat is occurred with Class 1

capacitors (Temp.Char. : C0G,U2J,X8G, etc.). When measuring, use a thermocouple of small thermal

capacity-K of Φ0.1mm and be in the condition where capacitor is not affected by radiant heat of other

components and wind of surroundings. Excessive heat may lead to deterioration of the capacitor’s

characteristics and reliability.

3. FAIL-SAFE

Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that

may be caused by the abnormal function or the failure of our product.

4. OPERATING AND STORAGE ENVIRONMENT

The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store

capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the

like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify

that these processes do not affect product quality by testing the performance of a cleaned, bonded or

molded product in the intended equipment. Store the capacitors where the temperature and relative

humidity do not exceed 5 to 40 °C and 20 to 70%. Use capacitors within 6 months.

5. VIBRATION AND IMPACT

Do not expose a capacitor or its leads to excessive shock or vibration during use.

6. SOLDERING

When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the

capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may

result in thermal shocks that can crack the ceramic element.

7. BONDING AND RESIN MOLDING, RESIN COAT

In case of bonding, molding or coating this product, verify that these processes do not affect the quality

of capacitor by testing the performance of a bonded or molded product in the intended equipment.

In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins

containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer

coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short

circuit.

The variation in thickness of adhesive or molding resin may cause a outer coating resin cracking and/or

ceramic element cracking of a capacitor in a temperature cycling.

8. TREATMENT AFTER BONDING AND RESIN MOLDING, RESIN COAT

When the outer coating is hot (over 100 °C) after soldering, it becomes soft and fragile.

So please be careful not to give it mechanical stress.

EGRH03

1/14

Reference only

Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial

dispersion when the product is used.

9. LIMITATION OF APPLICATIONS

Please contact us before using our products for the applications listed below which require especially

high reliability for the prevention of defects which might directly cause damage to the third party’s life,

body or property.

1. Aircraft equipment

2. Aerospace equipment

3. Undersea equipment

5. Medical equipment

7. Traffic signal equipment

4. Power plant control equipment

6. Transportation equipment (vehicles, trains, ships, etc.)

8. Disaster prevention / crime prevention equipment

9. Data-processing equipment exerting influence on public

10. Application of similar complexity and/or reliability requirements to the applications listed in the above.

NOTICE

1. CLEANING (ULTRASONIC CLEANING)

To perform ultrasonic cleaning, observe the following conditions.

Rinse bath capacity : Output of 20 watts per liter or less.

Rinsing time : 5 min maximum.

Do not vibrate the PCB/PWB directly.

Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires.

2. SOLDERING AND MOUNTING

Insertion of the Lead Wire

• When soldering, insert the lead wire into the PCB without mechanically stressing the lead wire.

• Insert the lead wire into the PCB with a distance appropriate to the lead space.

3. CAPACITANCE CHANGE OF CAPACITORS

• Class 2 capacitors (Temp.Char. : X7R,X7S,X8L etc.)

Class 2 capacitors an aging characteristic, whereby the capacitor continually decreases its capacitance

slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on

a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant

circuit.

Please contact us if you need a detail information.

4.WHEN USING THE FREQUENCY EXCEEDING 20kHz

In the case of use exceeding 150 °c, ESR of the capacitor increase by progress at time in the frequency

exceeding 20kHz, and the self-heating of the capacitor may be higher.

The heating temperature varies depending on the capacitance value and the applied voltage.

If you are considering using more than 20kHz, please contact us in advance.

NOTE

1. Please make sure that your product has been evaluated in view of your specifications with our product

being mounted to your product.

2. You are requested not to use our product deviating from this product specification.

EGRH03

2/14

Reference only

1. Application

This specification is applied to 200℃ Operation Leaded MLCC RHS series

iin accordance with AEC-Q200 requirements used for Automotive Electronic equipment.

2. Rating

• Applied maximum temperature up to 200℃

Note : Maximum accumulative time to 200℃ is within 2000 hours.

• Part Number Configuration

RHS

472

Dimension Lead

(LxW) Style

H01

ex.)

Series

Temperature

Characteristics

Rated

Voltage

Capacitance

Tolerance

Individual

Specification

Package

• Series

Code

RHS

Content

Epoxy coated, 200°C max.

• Temperature Characteristics

Code Temp. Char.

Standard

Temp.

Operating

Temp. Range

Cap. Change

X9Q

-55～125°C

125～200°C

+/-15%

+15/-70%

25°C

-55～200°C

(Murata code)

• Rated Voltage

Code

Rated voltage

DC100V

When the product temperature exceeds 150°C, please use this product

within the voltage and temperature derated conditions in the figure below.

• Capacitance

The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.

ex.) In case of 472

47×10²= 4700pF

• Capacitance Tolerance

Code

Capacitance Tolerance

+/-10%

TEIKAKU

3/14

Reference only

• Dimension (LxW)

Please refer to [ Part number list ].

• Lead Style

*Lead wire is "solder coated CP wire".

Code

Lead Style

Straight type

Lead spacing (mm)

2.5+/-0.8

Straight taping type

Inside crimp type

2.5+0.4/-0.2

5.0+/-0.8

Inside crimp taping type

5.0+0.6/-0.2

• Individual Specification

Murata’s control code.

Please refer to [ Part number list ].

• Package

Code

Package

Taping type of Ammo

Bulk type

3. Marking

Temp. char.

Capacitance

Capacitance tolerance

Rated voltage

Company name code

Letter code : N (X9Q char.)

3 digit numbers

Code

Letter code : 1 (DC100V. Except dimension code : 0,1)

Abbreviation :

(Except dimension code : 0,1)

(Ex.)

Rated voltage

DC100V

Dimension code

0,1

103K

224

K1N

TEIKAKU

4/14

Reference only

4. Part number list

Unit : mm

Dimension (mm)

Dimension Pack

Customer

Part Number

Rated

Volt.

(V)

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

qty.

Lead Style (pcs)

RHSQ92A472K0A2H01B X9Q

RHSQ92A682K0A2H01B X9Q

RHSQ92A103K0A2H01B X9Q

RHSQ92A153K0A2H01B X9Q

RHSQ92A223K0A2H01B X9Q

RHSQ92A333K1A2H01B X9Q

RHSQ92A473K1A2H01B X9Q

RHSQ92A683K1A2H01B X9Q

RHSQ92A104K1A2H01B X9Q

RHSQ92A154K2A2H01B X9Q

RHSQ92A224K2A2H01B X9Q

RHSQ92A472K0K1H01B X9Q

RHSQ92A682K0K1H01B X9Q

RHSQ92A103K0K1H01B X9Q

RHSQ92A153K0K1H01B X9Q

RHSQ92A223K0K1H01B X9Q

RHSQ92A333K1K1H01B X9Q

RHSQ92A473K1K1H01B X9Q

RHSQ92A683K1K1H01B X9Q

RHSQ92A104K1K1H01B X9Q

RHSQ92A154K2K1H01B X9Q

RHSQ92A224K2K1H01B X9Q

100

4700pF

6800pF

±10%

3.9

3.5

2.5

2.6

0A2

1A2

2A2

0K1

1K1

2K1

500

3.9

4.2

5.5

3.9

4.2

5.5

3.5

4.0

3.5

4.0

2.5

5.0

2.6

2.8

3.3

2.6

2.8

3.3

100 10000pF

100 15000pF

100 22000pF

100 33000pF

100 47000pF

100 68000pF

100

0.10μF

0.15μF

0.22μF

4700pF

6800pF

6.0

5.0

6.0

100 10000pF

100 15000pF

100 22000pF

100 33000pF

100 47000pF

100 68000pF

100

0.10μF

0.15μF

0.22μF

PNLIST

5/14

Reference only

Unit : mm

Rated

Volt.

(V)

Dimension (mm)

Dimension Pack

Customer

Part Number

Cap.

Tol.

Murata Part Number

T.C.

Cap.

(LxW)

Lead Style (pcs)

H/H0

qty.

RHSQ92A472K0DGH01A X9Q 100

RHSQ92A682K0DGH01A X9Q 100

4700pF

6800pF

±10%

3.9

4.2

5.5

3.9

4.2

5.5

3.5

2.5

5.0

2.6 20.0

2.8 20.0

3.3 20.0

2.6 20.0

2.8 20.0

3.3 20.0

0DG

1DG

2DG

0M2

1M2

2M2

2000

1500

2000

1500

3.5

4.0

3.5

4.0

RHSQ92A103K0DGH01A X9Q 100 10000pF

RHSQ92A153K0DGH01A X9Q 100 15000pF

RHSQ92A223K0DGH01A X9Q 100 22000pF

RHSQ92A333K1DGH01A X9Q 100 33000pF

RHSQ92A473K1DGH01A X9Q 100 47000pF

RHSQ92A683K1DGH01A X9Q 100 68000pF

RHSQ92A104K1DGH01A X9Q 100

RHSQ92A154K2DGH01A X9Q 100

RHSQ92A224K2DGH01A X9Q 100

RHSQ92A472K0M2H01A X9Q 100

RHSQ92A682K0M2H01A X9Q 100

0.10μF

0.15μF

0.22μF

4700pF

6800pF

6.0

5.0

6.0

RHSQ92A103K0M2H01A X9Q 100 10000pF

RHSQ92A153K0M2H01A X9Q 100 15000pF

RHSQ92A223K0M2H01A X9Q 100 22000pF

RHSQ92A333K1M2H01A X9Q 100 33000pF

RHSQ92A473K1M2H01A X9Q 100 47000pF

RHSQ92A683K1M2H01A X9Q 100 68000pF

RHSQ92A104K1M2H01A X9Q 100

RHSQ92A154K2M2H01A X9Q 100

RHSQ92A224K2M2H01A X9Q 100

0.10μF

0.15μF

0.22μF

PNLIST

6/14

Reference only

5. AEC-Q200 Murata Standard Specifications and Test Methods

No.

AEC-Q200 Test Item

Pre-and Post-Stress

Electrical Test

Specification

AEC-Q200 Test Method

High

Appearance No defects or abnormalities except color

change of outer coating.

Sit the capacitor for 1000±12 hours at 200±5°C. Let sit for 24±2 hours

at *room condition , then measure.

Temperature

Exposure

(Storage)

Capacitance within ±12.5%

Change

•Pretreatment

D.F.

I.R.

0.04 max.

Perform the heat treatment at 150+0/-10°C for 60±5 min and

then let sit for 24±2 hours at *room condition.

More than 1,000MΩ or 50 MΩ・μF

(Whichever is smaller)

Temperature Appearance No defects or abnormalities except color

Perform the 1000 cycles according to the four heat treatments listed in

the following table. Let sit for 24±2 hours at *room condition, then measure.

Cycling

change of outer coating.

Capacitance within ±12.5%

Change

D.F.

0.05 max.

I.R.

1,000MΩ or 50MΩ・μF min.

(Whichever is smaller)

•Pretreatment

Perform the heat treatment at 150+0/-10°C for 60±5 min and

then let sit for 24±2 hours at *room condition.

Apply the 24h heat (25 to 65°C) and humidity (80 to 98%)

treatment shown below, 10 consecutive times.

Let sit for 24±2 hours at *room condition, then measure.

Moisture

Appearance No defects or abnormalities.

Capacitance within ±12.5%

Change

Resistance

D.F.

I.R.

0.05 max.

500MΩ or 25MΩ・μF min.

(Whichever is smaller)

•Pretreatment

Perform the heat treatment at 150+0/-10°C for 60±5 min and

then let sit for 24±2 hours at *room condition.

Apply the rated voltage and DC1.3+0.2/-0V (add 100kΩ resistor)

at 85±3°C and 80 to 85% humidity for 1000±12 hours.

Remove and let sit for 24±2 hours at *room condition, then measure.

The charge/discharge current is less than 50mA.

• Pretreatment

Biased

Appearance No defects or abnormalities.

Capacitance within ±12.5%

Change

Humidity

D.F.

I.R.

0.05 max.

500MΩ or 25MΩ·μF min.

(Whichever is smaller)

Perform a heat treatment at 150+0/-10°C for one hour.

and then set at room temperature for 24±2 hours.

Apply 25% of the rated voltage for 1000±12 hours at 200±5°C.

Let sit for 24±2 hours at *room condition, then measure.

The charge/discharge current is less than 50mA.

•Pretreatment

Operational

Life

Appearance No defects or abnormalities except color

change of outer coating.

Capacitance within ±15.0%

Change

D.F.

I.R.

0.04 max.

Apply test voltage for 60±5 min at test temperature.

Remove and let sit for 24±2 hours at *room condition.

100MΩ or 5MΩ・μF min.

(Whichever is smaller)

External Visual

No defects or abnormalities.

Within the specified dimensions.

To be easily legible.

Visual inspection.

Physical Dimension

Marking

Using calipers and micrometers.

Visual inspection.

10 Resistance

to Solvents

Appearance No defects or abnormalities.

Capacitance Within the specified tolerance.

Per MIL-STD-202 Method 215

Solvent 1 : 1 part (by volume) of isopropyl alcohol

3 parts (by volume) of mineral spirits

Solvent 2 : Terpene defluxer

D.F.

I.R.

0.025 max.

More than 10,000MΩ or 500 MΩ・μF

(Whichever is smaller)

Solvent 3 : 42 parts (by volume) of water

1part (by volume) of propylene glycol monomethyl ether

1 part (by volume) of monoethanolamine

* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa

ESRH08

7/14

Reference only

No.

AEC-Q200 Test Item

Specification

Appearance No defects or abnormalities.

Capacitance Within the specified tolerance.

AEC-Q200 Test Method

11 Mechanical

Shock

Three shocks in each direction should be applied along 3

mutually perpendicular axes of the test specimen (18 shocks).

The specified test pulse should be Half-sine and should have a

duration : 0.5ms, peak value : 1500G and velocity change : 4.7m/s.

The capacitor should be subjected to a simple harmonic motion

having a total amplitude of 1.5mm, the frequency being varied

uniformly between the approximate limits of 10 and 2000Hz.

The frequency range, from 10 to 2000Hz and return to 10Hz,

should be traversed in approximately 20 min. This motion

should be applied for 12 items in each 3 mutually perpendicular

directions (total of 36 times).

D.F.

0.025 max.

12 Vibration

Appearance No defects or abnormalities.

Capacitance Within the specified tolerance.

D.F.

0.025 max.

13-1 Resistance

Appearance No defects or abnormalities.

Change

The lead wires should be immersed in the melted solder 1.5 to 2.0mm

from the root of terminal at 260±5°C for 10±1 seconds.

to Soldering Capacitance Within ±7.5%

Heat

(Non-

Dielectric

Strength

(Between

terminals)

No defects

• Pre-treatment

Preheat)

Capacitor should be stored at 150+0/-10°C for one hour,

then place at *room condition for 24±2 hours before initial measurement.

• Post-treatment

Capacitor should be stored for 24±2 hours at *room condition.

First the capacitor should be stored at 120+0/-5°C for 60+0/-5 seconds.

Then, the lead wires should be immersed in the melted solder

1.5 to 2.0mm from the root of terminal at 260±5°C for 7.5+0/-1 seconds.

13-2 Resistance

Appearance No defects or abnormalities.

to Soldering Capacitance Within ±7.5%

Heat

Change

(On-

Dielectric

Strength

(Between

terminals)

No defects

Preheat)

• Pre-treatment

Capacitor should be stored at 150+0/-10°C for one hour,

then place at *room condition for 24±2 hours before initial measurement.

• Post-treatment

Capacitor should be stored for 24±2 hours at *room condition.

Test condition

13-3 Resistance

Appearance No defects or abnormalities.

Change

to Soldering Capacitance Within ±7.5%

Termperature of iron-tip : 350±10°C

Heat

Soldering time : 3.5±0.5 seconds

(soldering

Dielectric

Strength

(Between

terminals)

No defects

Soldering position

iron method)

Straight Lead : 1.5 to 2.0mm from the root of terminal.

Crimp Lead : 1.5 to 2.0mm from the end of lead bend.

• Pre-treatment

Capacitor should be stored at 150+0/-10°C for one hour,

then place at *room condition for 24±2 hours before initial measurement.

• Post-treatment

Capacitor should be stored for 24±2 hours at *room condition.

Perform the 300 cycles according to the two heat treatments listed in the

following table (Maximum transfer time is 20 seconds.).

Let sit for 24±2 hours at *room condition, then measure.

14 Thermal

Shock

Appearance No defects or abnormalities except color

change of outer coating.

Capacitance within ±12.5%

Change

D.F.

I.R.

0.05 max.

1,000MΩ or 50MΩ・μF min.

(Whichever is smaller)

•Pretreatment

Perform the heat treatment at 150+0/-10°C for 60±5 min and

then let sit for 24±2 hours at *room condition.

Per AEC-Q200-002

15 ESD

Appearance No defects or abnormalities.

Capacitance Within the specified tolerance.

D.F.

I.R.

0.025 max.

More than 10,000MΩ or 500 MΩ・μF

(Whichever is smaller)

16 Solderability

Lead wire should be soldered with

uniform coating on the axial direction

over 95% of the circumferential direction.

The terminal of a capacitor is dipped into a solution of ethanol

(JIS-K-8101) and rosin (JIS-K-5902) (25% rosin in weight propotion) and

then into molten solder (JIS-Z-3282) for 2±0.5 seconds. In both cases the

depth of dipping is up to about 1.5 to 2mm from the terminal body.

Temp. of solder :

245±5°C Lead Free Solder (Sn-3.0Ag-0.5Cu)

235±5°C H60A or H63A Eutectic Solder

* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa

ESRH08

8/14

Reference only

No.

AEC-Q200 Test Item

Specification

No defects or abnormalities.

Capacitance Within the specified tolerance.

AEC-Q200 Test Method

17 Electrical

Characte-

rization

Apperance

Visual inspection.

The capacitance/D.F. should be measured at 25°C at the frequency

and voltage shown in the table.

D.F.

0.025 max.

Insulation

Resistance

(I.R.)

Room

10,000MΩ or 500MΩ・μF min.

The insulation resistance should be measured at 25±3 °C with a

DC voltage not exceeding the rated voltage at normal temperature

and humidity and within 2 min. of charging.

Temperature (Whichever is smaller)

(Charge/Discharge current ≦ 50mA.)

High

0.5MΩ or 0.1MΩ・μF min.

The insulation resistance should be measured at 200±5 °C with a

DC voltage not exceeding 25% of the rated voltage at normal

temperature and humidity and within 2 min. of charging.

(Charge/Discharge current ≦ 50mA.)

Temperature (Whichever is smaller)

Dielectric

Strength

Between

No defects or abnormalities.

The capacitor should not be damaged when DC voltage of 250%

of the rated voltage is applied between the terminations for 1 to 5

seconds.

Terminals

(Charge/Discharge current ≦ 50mA.)

Body

The capacitor is placed in a container with metal

balls of 1mm diameter so that each terminal,

Insulation

Approx.

2mm

short-circuit is kept approximately 2mm from

the balls, and 250% of the rated DC voltage is

impressed for 1 to 5 seconds between

capacitor terminals and metal balls.

Metal

balls

(Charge/Discharge current ≦ 50mA.)

18 Terminal

Strength

Tensile

Termination not to be broken or loosened.

As in the figure, fix the capacitor body, apply the force gradually

Strength

to each lead in the radial direction of the capacitor until reaching

10N and then keep the force applied for 10±1 seconds.

↓

Bending

Strength

Termination not to be broken or loosened.

Each lead wire should be subjected to a force of 2.5N and then

be bent 90° at the point of egress in one direction. Each wire is

then returned to the original position and bent 90° in the opposite

direction at the rate of one bend per 2 to 3 seconds.

The capacitance change should be measured after 5min. at

each specified temperature step.

19 Capacitance

Temperature

Within the specified Tolerance.

-55 to 125°C : within ±15%

Characteristics

125 to 200°C : within +15/-70%

The ranges of capacitance change compared with the above

25°C value over the temperature ranges shown in the table

should be within the specified ranges.

•Pretreatment

Perform the heat treatment at 150+0/-10°C for 60±5 min and

then let sit for 24±2 hours at *room condition.

Perform the initial measurement.

* “room condition” Temperature : 15 to 35°C, Relative humidity : 45 to 75%, Atmosphere pressure : 86 to 106kPa

ESRH08

9/14

Reference only

6. Packing specification

・Bulk type (Packing style code : B)

The size of packing case and packing way

Polyethylene bag

Partition

270 max.

125 max.

Unit : mm

340 max.

The number of packing = ^*1Packing quantity × ^*2n

*1 : Please refer to [Part number list].

*2 : Standard n = 20 (bag)

Note)

The outer package and the number of outer packing be changed by the order getting amount.

JKBCRPE02

10/14

Reference only

・Ammo pack taping type (Packing style code : A)

ꢀꢀꢀꢀꢀꢀA crease is made every 25 pitches, and the tape with capacitors is packed zigzag into a case.

ꢀꢀꢀꢀꢀꢀWhen body of the capacitor is piled on other body under it.

The size of packing case and packing way

240 max.

Position of label

340 max.

Unit : mm

51 max.

Hold down tape

Capacitor

Base tape

Hold down

tape upper

EKTRPE01

11/14

Reference only

7. Taping specification

7-1. Dimension of capacitors on tape

Straight taping type < Lead Style : DG >

Pitch of component 12.7mm / Lead spacing 2.5mm

△S

△h2

△h1

Marking

Φd

ΦD0

Unit : mm

Item

Code

Dimensions

12.7+/-1.0

12.7+/-0.2

2.5+0.4/-0.2

Remarks

Pitch of component

Pitch of sprocket hole

Lead spacing

Length from hole center to component

center

6.35+/-1.3

Deviation of progress direction

They include deviation by lead bend

Deviation of tape width direction

Length from hole center to lead

ΔS

5.1+/-0.7

0+/-2.0

Deviation along tape, left or right defect

Carrier tape width

18.0+/-0.5

9.0+0/-0.5

Position of sprocket hole

Lead distance between reference and

bottom plane

20.0+/-0.5

Protrusion length

0.5 max.

4.0+/-0.1

0.5+/-0.05

0.6+/-0.3

1.5 max.

Diameter of sprocket hole

Lead diameter

ΦD0

Φd

Total tape thickness

They include hold down tape

thickness

Total thickness of tape and lead wire

Δh1

Δh2

Deviation across tape

1.0 max.

Portion to cut in case of defect

Hold down tape width

11.0+0/-1.0

9.5 min.

Hold down tape position

Coating extension on lead

1.5+/-1.5

2.0 max.

ETP1DBG01A

12/14

Reference only

Inside crimp taping type < Lead Style : M2 >

Pitch of component 12.7mm / Lead spacing 5.0mm

Unit : mm

Item

Code

Dimensions

12.7+/-1.0

12.7+/-0.2

5.0+0.6/-0.2

Remarks

Pitch of component

Pitch of sprocket hole

Lead spacing

Length from hole center to component

center

6.35+/-1.3

Deviation of progress direction

They include deviation by lead bend

Deviation of tape width direction

Length from hole center to lead

Deviation along tape, left or right defect

Carrier tape width

ΔS

3.85+/-0.7

0+/-2.0

18.0+/-0.5

9.0+0/-0.5

Position of sprocket hole

Lead distance between reference and

bottom plane

20.0+/-0.5

Protrusion length

0.5 max.

4.0+/-0.1

0.5+/-0.05

0.6+/-0.3

1.5 max.

Diameter of sprocket hole

Lead diameter

ΦD0

Φd

Total tape thickness

They include hold down tape

thickness

Total thickness of tape and lead wire

2.0 max. (Dimension code : W)

1.0 max. (except as above)

11.0+0/-1.0

Δh1

Δh2

Deviation across tape

Portion to cut in case of defect

Hold down tape width

9.5 min.

Hold down tape position

Coating extension on lead

1.5+/-1.5

Up to the end of crimp

ETP1M201A

13/14

Reference only

7-2. Splicing way of tape

1) Adhesive force of tape is over 3N at test condition as below.

Hold down tape

Base tape

2) Splicing of tape

a) When base tape is spliced

•Base tape shall be spliced by cellophane tape.

(Total tape thickness shall be less than 1.05mm.)

Progress direction

in production line

Hold down tape

Base tape

About 30 to 50

No lifting for the

Cellophane tape

direction of

progressing

Unit : mm

b) When hold down tape is spliced

•Hold down tape shall be spliced with overlapping.

(Total tape thickness shall be less than 1.05mm.)

20 to 30

Hold down tape

Base tape

Unit : mm

Progress direction

in production line

c) When both tape are spliced

•Base tape and hold down tape shall be spliced with splicing tape.

ETP2R01

14/14

RHSQ92A153K0K1H01B [MURATA]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E