首页 |元器件品牌

FM0H104ZFTP [NEC]

Super Capacitors; 超级电容器
FM0H104ZFTP
型号： FM0H104ZFTP
厂家： NEC    NEC
描述：

Super Capacitors
超级电容器

电容器
文件： 总39页 (文件大小：476K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
Vol. 1 2  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
FOR CORRECT USE OF SUPER CAPACITORS  
1.Please confirm the operating conditions and the specifications of the  
Super Capacitors befor using them.  
2.The electrolyte of these Super Capacitors is sealed with material such as rubber.  
When you use the capacitors for a long time at high temperature, the moisture of  
the eleotrolyte evaporates and the equivalent series resistance (E.S.R.) increases.  
The fundamental failure mode is the open mode depending on E.S.R. increase.  
When using a capacitor, please introduce a safe design assuming unex-  
pected capacitor failure, such as redundancy in design and protection from  
fire and erroneous operation.  
3.Please read 'Notes on Using the Super Capacitor' on page 60 when you design  
the circuits using the Super Capacitors.  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
CONTENTS  
page  
1. Organization of Super Capacitor Series ……………………………………………………………  
2. Performance for Selection ……………………………………………………………………………  
3. Characteristics of Super Capacitor …………………………………………………………………  
4. Typical Applications ……………………………………………………………………………………  
5. Part Number System ……………………………………………………………………………………  
6. Rated Specifications ……………………………………………………………………………………  
6.1 FC Series（SMD Type） …………………………………………………………………………  
4
5
5
6
7
9
9
6.2 FM Series ………………………………………………………………………………………… 13  
6.3 FG Series ………………………………………………………………………………………… 20  
6.4 FT Series ………………………………………………………………………………………… 22  
6.5 FY Series ………………………………………………………………………………………… 24  
6.6 FR Series ………………………………………………………………………………………… 26  
6.7 FS Series ………………………………………………………………………………………… 28  
6.8 FA，FE Series …………………………………………………………………………………… 30  
6.9 HV Series（High Capacitance Type）………………………………………………………… 32  
7. Packing …………………………………………………………………………………………………… 33  
8. List of Plating Type and Sleeve Type ……………………………………………………………… 34  
9. Measurement Conditions ……………………………………………………………………………… 35  
10. Notes on Using Super Capacitor（Electric Double-Layer Capacitor） ……………………… 36  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
1. Organization of Super Capacitor Series  
－25 to 70℃  
－40 to 85℃  
guaranteed  
guaranteed  
mA order  
back-up  
μA order  
back-up  
For automatic  
mounting  
FC  
series  
3.5 to 5.5V  
（SMD）  
（embossad taping）  
FME  
For automatic  
mounting  
（radial taping）  
FM  
series  
3.5 to 6.5V  
FMR  
Type  
3.5 to 5.5V  
FML  
Type  
5.5V  
－40 to 85℃  
guaranteed  
FT  
series  
5.5V  
FG  
series  
3.5 to 5.5V  
FGR  
Type  
5.5V  
（Csealf-nsuCppaosrtiengtTyyppee）  
FS  
series  
5.5 to 11V  
FY  
series  
3.5 to 5.5V  
FR  
series  
5.5V  
FE  
series  
5.5V  
FA  
series  
5.5 to 11V  
For A order  
current  
HV  
series  
2.7V  
10 to 100F  
4
Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
2. Performance for Selection  
kA  
High power  
SuperCapacitor  
A
BOX type  
High power  
SuperCapacitor  
HV Series  
Low impedance application use  
FA, FE, FS, FT, FM Series  
mA  
High impedance application use  
FG, FY, FC, FM, FR Series  
μ
A
0.01  
0.1  
1
10  
102  
103  
1 hour  
104  
105  
106  
107  
108  
Backup time  
1 minute  
1 day 1 week  
1 month  
( sec )  
Backup time depends on capacitance  
3. Characteristics of Super Capacitor  
Super Capacitor can not be used for applications in AC circuit such as ripple absorption because it has high internal resistance  
(several hundred mΩ to a hundred Ω) compared to aluminum electrolysis capacitor. Thus its main use would be similar to that  
of secondary battery such as power back-up in DC circuit. The following list shows the characteristics of Super Capacitors as  
compared to aluminum electrolyses capacitors for power back-up and secondary batteries.  
Secondary battery  
Capacitor  
NiCd battery  
Lithium ion battery  
◎
Aluminum electrolysis capacito  
Super Capacitor  
○
Back-up ability  
◎
△
－－－  
Eco-hazard  
Cd  
－－－  
－－－  
Operating temperature range  
Charge time  
－20 to 60 ℃  
few hours  
－20 to 50 ℃  
few hours  
－55 to 105 ℃  
few minutes  
limitless (*1)  
none  
－40 to 85 ℃（FR，FT）  
few minutes  
Charge/discharge life time  
Restrictions on charge/discharge  
Flow soldering  
approx. 500 times  
yes  
approx. 500 to 1000 times  
yes  
limitless (*1)  
none  
not applicable  
not applicable  
leakage, explosion  
not applicable  
not applicable  
leakage, combustion, explosion, ignition  
applicable  
applicable  
heat-up, explosion  
applicable  
Automatic mounting  
Safety risks  
applicable (FM and FC series)  
gas emission (*2)  
(*1) Aluminum electrolysis capacitor and Super Capacitor has limited lifetime. However, when used under proper conditions, both can operate  
sufficiently within the designed lifetime of the set they are built in.  
(*2) There is no harm as it is a mere leak of water vapor which transitioned from water contained in the electrolyte (diluted sulfuric acid).  
However, application of abnormal voltage surge exceeding maximum operating voltage may result in leakage and explosion.  
Super Capacitors Vol.12  
5
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
4. Typical Applications  
As in the characteristics remarked previously, Super Capacitor has characteristics intermediate between general capacitors and  
batteries. Because of this, Super Capacitor can be used like a secondary battery when applied to DC circuit. The best suited  
applications of Super Capacitor are back-up device for the power shut-down of micro computers and RAM's. The list below  
shows main application examples.  
Application Examples of Super Capacitor  
Intended use  
(guideline)  
Power supply  
(guideline)  
Application  
Examples of equipments  
Series  
・
Measuring device, Control equipment,  
Communication device,  
Automotive power source  
・FR series  
(85℃ guaranteed)  
・CMOS RAM, IC for clocks  
Long time  
back-up  
500μA and below  
・FC series  
・FG series  
・FY series  
・FM series  
・CMOS micro computer  
・Static RAM/DTS  
(digital tuning system)  
・CMOS micro computer, IC for  
clocks  
・VCR, Microwave oven,  
・Micro computer  
・Micro computer, RAM  
・Driving motor  
・Memory equipped device  
Back-up for  
1 hour or less  
・FT series  
・FS series  
50 mA and below  
・VCR, Printer, Projector  
・Video disk  
・Subsidiary power supply for driving  
motor during voltage drop  
・Camera  
・Power source of toys, LED, buzzer  
・Toys, Display device, Alarm device  
Back-up for  
10 seconds  
or less  
・FA series  
・FE series  
1 A and below  
Up to several A  
・High current supply for a short  
amount of time  
・Actuator, Relay solenoid, Gas igniter  
・Power supply, Subsidiary power  
supply  
Power assist  
・Street sign, Display light , UPS  
・HV series  
6
Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
5. Part Number System  
FM, FC, FT, FG, FS, FR, FY, FE, FA Series  
FG Series bulk type  
FG  
0H  
223  
Z
F
Environmental pollutant reduced  
Capacitance tolerance  
＋80％, －20％  
Nominal capacitance（μF）  
First two digits represent significant figure  
Third digit specifies number of zeroes to follow microfarad code.  
Maximum operating voltage  
0V：3.5Vdc, 0H：5.5Vdc, 0J：6.5Vdc, 1A：11Vdc, 1B：12Vdc  
Series name  
FM Series tape type (Ammo pack)  
FM0H223ZF  
TP  
16  
Height (excluding lead)  
16：16mm  
18：18mm  
Tape type  
Bulk part name  
FC Series tape type (Embossed tape)  
FC0H104ZF TB  
R
24 - SS  
Indivisual management code  
Tape width  
Positive electrode position in relation to tapes forward direction  
Embossed tape type  
Bulk part name  
Super Capacitors Vol.12  
7
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
HV Series  
HV 0E 106  
N
F
Environmental pollutant reduced  
Capacitance tolerance  
±30％  
Nominal capacitance（μF）  
First two digits represent significant fifure  
Third digit specifies number of zeroes to follow microfarad code.  
Maximum operating voltage  
0E：2.7Vdc  
Series name  
8
Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
6. Rated Specifications  
6.1 FC Series  
Features  
Dimensions  
• Enables surface mounting.  
• High rated voltage of 5.5V.  
• High leakage reliability.  
B±0.2  
D±0.5  
A±0.2  
Negative  
H max.  
L
W±0.1  
terminal  
K
Positive  
terminal  
I
P
I
Markings  
Displays nominal capacitance, MAX operating voltage serial number, polarity and etc.  
Polarity  
(negative)  
Nominal  
capacitance  
Polarity  
(negative)  
Nominal  
capacitance  
Series name Logo  
MAX  
operating voltage  
N T  
FC 5.5V  
474  
A1-001  
MAX  
operating voltage  
MAX  
operating voltage  
Polarity  
(negative)  
473  
5.5V  
A1  
473  
5.5V  
A1  
Nominal  
capacitance  
FCS Type  
S
Serial number  
Date code  
Date code  
Date code  
FC0H474ZFTBR32-SS  
FC0H105ZFTBR44-SS  
FC0H473ZFTBR24  
FC0H104ZFTBR24  
FC0H224ZFTBR24  
FC0V104ZFTBR24  
FC0V224ZFTBR24  
FC0V474ZFTBR24  
FCH0V683ZFTBR16  
FCH0V433ZFTBR16  
FCS0H473ZFTBR24  
FCS0H104ZFTBR24  
FCS0H224ZFTBR24  
FCS0V104ZFTBR24  
FCS0V224ZFTBR24  
FCS0V474ZFTBR24  
Standard models  
●FC Type  
Max.  
Nominal  
Max.  
current at  
Voltage  
Holding  
Dimension (Unit:mm)  
Max. ESR  
Operating Capacitance  
Weight  
Part Number  
(at 1kHz)  
Voltage  
(Vdc)  
Discharge  
system (F)  
30 minutes Characteristic  
(g)  
(Ω)  
D
H
A
B
I
W
P
K
L
(mA)  
0.071  
0.15  
0.33  
0.71  
1.50  
0.09  
0.20  
0.42  
Min. (V)  
4.2  
4.2  
4.2  
4.2  
4.2  
̶
＋0.3  
FC0H473ZFTBR24  
FC0H104ZFTBR24  
FC0H224ZFTBR24  
FC0H474ZFTBR32-SS  
FC0H105ZFTBR44-SS  
FC0V104ZFTBR24  
FC0V224ZFTBR24  
FC0V474ZFTBR24  
5.5  
5.5  
5.5  
5.5  
5.5  
3.5  
3.5  
3.5  
0.047  
0.10  
0.22  
0.47  
1.0  
0.10  
0.22  
0.47  
50  
25  
25  
13  
7
50  
25  
25  
10.5  
10.5  
10.5  
16.0  
5.5  
5.5  
8.5  
9.5  
10.8 10.8 3.6±0.5 1.2  
10.8 10.8 3.6±0.5 1.2  
10.8 10.8 3.6±0.5 1.2  
16.3 16.3 6.8±1.0 1.2  
5.0 0.7±0.3  
5.0 0.7±0.3  
5.0 0.7±0.3  
5.0 1.2±0.5  
10.0 1.2±0.5  
5.0 0.7±0.3  
5.0 0.7±0.3  
5.0 0.7±0.3  
0
0
0
0
0
0
0
0
1.0  
1.0  
1.4  
4.0  
6.7  
1.0  
1.0  
1.4  
－0.1  
＋0.3  
－0.1  
＋0.3  
－0.1  
＋0.5  
－0.1  
＋0.5  
21.0 10.5 21.6 21.6 7.0±1.0 1.4  
－0.1  
＋0.3  
－0.1  
10.5  
10.5  
10.5  
5.5  
5.5  
8.5  
10.8 10.8 3.6±0.5 1.2  
10.8 10.8 3.6±0.5 1.2  
10.8 10.8 3.6±0.5 1.2  
＋0.3  
̶
̶
－0.1  
＋0.3  
－0.1  
●FCH Type  
Max.  
Nominal  
Max.  
Voltage  
Holding  
Dimension (Unit:mm)  
Max. ESR  
(at 1kHz)  
(Ω)  
Operating Capacitance  
current at  
Weight  
(g)  
Part Number  
Voltage  
(Vdc)  
3.6  
5.5  
Discharge  
system (F)  
0.068  
0.043  
30 minutes Characteristic  
D
H
A
B
I
W
P
K
L
(mA)  
0.062  
0.065  
Min. (V)  
̶
̶
＋0.3  
FCH0V683ZFTBR16  
FCH0H433ZFTBR16  
40  
50  
6.8  
6.8  
3.7  
5.0  
6.8  
6.8  
6.8 2.9±0.5 0.7  
6.8 2.9±0.5 0.7  
2.5 0.7±0.3  
2.5 0.7±0.3  
0
0
0.3  
0.4  
－0.1  
＋0.3  
－0.1  
●FCS Type  
Max.  
Nominal  
Max.  
Voltage  
Holding  
Dimension (Unit:mm)  
Max. ESR  
(at 1kHz)  
(Ω)  
Operating Capacitance  
current at  
Weight  
(g)  
Part Number  
Voltage  
(Vdc)  
Discharge  
system (F)  
30 minutes Characteristic  
D
H
A
B
I
W
P
K
L
(mA)  
0.071  
0.15  
0.33  
0.09  
0.20  
0.42  
Min. (V)  
4.2  
4.2  
4.2  
̶
̶
̶
＋0.3  
FCS0H473ZFTBR24  
FCS0H104ZFTBR24  
FCS0H224ZFTBR24  
FCS0V104ZFTBR24  
FCS0V224ZFTBR24  
FCS0V474ZFTBR24  
5.5  
5.5  
5.5  
3.5  
3.5  
3.5  
0.047  
0.10  
0.22  
0.10  
0.22  
0.47  
100  
50  
50  
100  
50  
50  
10.7  
10.7  
10.7  
10.7  
10.7  
10.7  
5.5  
5.5  
8.5  
5.5  
5.5  
8.5  
10.8 10.8 3.9±0.5 1.2  
10.8 10.8 3.9±0.5 1.2  
10.8 10.8 3.9±0.5 1.2  
10.8 10.8 3.9±0.5 1.2  
10.8 10.8 3.9±0.5 1.2  
10.8 10.8 3.9±0.5 1.2  
5.0 0.9±0.3  
5.0 0.9±0.3  
5.0 0.9±0.3  
5.0 0.9±0.3  
5.0 0.9±0.3  
5.0 0.9±0.3  
0
0
0
0
0
0
1.0  
1.0  
1.4  
1.0  
1.0  
1.4  
－0.1  
＋0.3  
－0.1  
＋0.3  
－0.1  
＋0.3  
－0.1  
＋0.3  
－0.1  
＋0.3  
－0.1  
Super Capacitors Vol.12  
9
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Precautions for use  
・This series is exclusively for reflow soldering. It is designed for thermal conduction system such as combination use of infrared  
ray and heat blow. Consult with NEC TOKIN before applying other methods.  
・The reflow condition must be kept within reflow profile graphs shown below.  
・Applying reflow soldering is limited to 2 times. After the first reflow, cool down the capacitor thoroughly to 5-35℃ before the  
second reflow.  
Always consult with NEC TOKIN when applying reflow soldering in a more severe condition than the condition described here.  
・FCS Type  
・FC, FCH Type  
Reflow profile  
Peak temperature  
Peak temperature:  
Temperature on the  
capacitor top  
Reflow profile  
235℃，within 10sec.  
250  
200  
300  
250  
260℃  
160  
℃
217℃  
200  
150  
100  
50  
200℃  
150  
100  
50  
70sec  
150℃  
120sec  
150sec  
Tp Time exceeding 200℃  
Time (sec)  
0
0
0
50  
100  
150  
200  
Time (sec)  
250  
300  
350  
400  
Tp Time exceeding 200℃  
・Above "Reflow Profile" graph indicates temperature at the  
terminals and capacitor top.  
250  
240  
230  
220  
210  
200  
Peak temperature  
Over 255℃  
Below 260℃  
Within 10sec.  
Within 45sec.  
Within 60sec.  
Within 70sec.  
150sec.  
Over 230℃  
0
10  
20  
30  
40  
50  
60  
Over 220℃  
Tp (sec)  
Over 217℃  
Time between 150℃ to  
200℃（temperature zone  
over 170℃＝within 50sec.）  
・Above "Reflow Profile" graph indicates temperature at the  
terminals and capacitor top.  
10 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Tape and Reel Dimensions  
[Reel Dimensions]  
(mm)  
TBR44  
Mark  
A
TBR16  
TBR24  
380±2  
TBR32  
E
C
380±2  
330±2  
380±2  
Product height 5.5mm  
80±1  
B
80±1  
100±1  
100±1  
Product height 8.5mm 100±1  
C
D
E
13±0.5  
21±0.8  
2±0.5  
13±0.5  
21±0.8  
2±0.5  
13±0.5 13±0.5  
21±0.8 21±0.8  
D
R:10  
2±0.5  
2±0.5  
Product height 5.5mm 25.5±0.5  
Product height 8.5mm 25.5±1.0  
2.0  
t
W
t
17.5±1.0  
33.5±1.0 45.5±1.0  
A
W
2.0  
2.0  
2.0  
Dimensions of indented [square-hole plastic tape]  
●TBR16/24  
(mm)  
Sprocket hole  
FD  
0
t
1
Mark  
W
TBR16  
16.0  
TBR24  
TBR32  
32.0  
18.0  
20.0  
4.0  
TBR44  
44.0  
23.0  
25.0  
4.0  
P
2
P0  
24.0  
A
A
7.2  
9.0  
11.4  
B
13.0  
P0  
P1  
P2  
F
4.0  
4.0  
Indented square-hole  
Forward direction  
P1  
for fitting super capacitors  
12.0  
2.0  
16.0  
24.0  
2.0  
32.0  
2.0  
t2  
Super capacitors fitting  
on square-hole  
2.0  
7.5  
11.5  
14.2  
1.55  
0.5  
20.2  
1.55  
0.5  
●TBR32/44  
FD0  
φD0  
t1  
1.55  
0.4  
1.55  
P2  
P
0
t
1
0.4  
A
E
1.75  
1.75  
Product height 5.5mm 6.0  
Product height 8.5mm 8.4  
–
1.75  
1.75  
t2  
5.0  
–
10.0  
28.4  
12.0  
40.4  
G
t2  
P1  
Super capacitors fitting  
on square-hole  
R0.75  
0.2  
Recommended land pattern  
Land pattern  
Lead terminal  
(mm)  
(mm)  
Part Number  
A
B
C
Part Number  
A
B
C
FC0H473ZFTBR24  
FC0H104ZFTBR24  
FC0H224ZFTBR24  
FC0H474ZFTBR32-SS  
5.0  
5.0  
5.0  
5.0  
4.6  
4.6  
4.6  
10.0  
10.5  
4.6  
2.5  
2.5  
2.5  
2.5  
3.5  
2.5  
2.5  
2.5  
FC0H473ZFTBR24  
FC0H104ZFTBR24  
FC0H224ZFTBR24  
FC0H474ZFTBR32-SS  
5.0  
5.0  
5.0  
5.0  
3.6  
3.6  
3.6  
6.8  
7.0  
3.6  
3.6  
3.6  
1.2  
1.2  
1.2  
1.2  
1.4  
1.2  
1.2  
1.2  
FC0H105ZFTBR44-SS 10.0  
FC0H105ZFTBR44-SS 10.0  
FC0V104ZFTBR24  
FC0V224ZFTBR24  
FC0V474ZFTBR24  
5.0  
5.0  
5.0  
FC0V104ZFTBR24  
FC0V224ZFTBR24  
FC0V474ZFTBR24  
5.0  
5.0  
5.0  
4.6  
4.6  
FCH0V683ZFTBR16  
FCH0H433ZFTBR16  
2.5  
2.5  
4.0  
4.0  
1.4  
1.4  
FCH0V683ZFTBR16  
FCH0H433ZFTBR16  
2.5  
2.5  
2.9  
2.9  
0.7  
0.7  
Logo  
FCS0H473ZFTBR24  
FCS0H104ZFTBR24  
FCS0H224ZFTBR24  
FCS0V104ZFTBR24  
FCS0V224ZFTBR24  
FCS0V474ZFTBR24  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
4.9  
4.9  
4.9  
4.9  
4.9  
4.9  
2.5  
2.5  
2.5  
2.5  
2.5  
2.5  
FCS0H473ZFTBR24  
FCS0H104ZFTBR24  
FCS0H224ZFTBR24  
FCS0V104ZFTBR24  
FCS0V224ZFTBR24  
FCS0V474ZFTBR24  
5.0  
5.0  
5.0  
5.0  
5.0  
5.0  
3.9  
3.9  
3.9  
3.9  
3.9  
3.9  
1.2  
1.2  
1.2  
1.2  
1.2  
1.2  
B
A
B
Super Capacitors Vol.12 11  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Specifications  
Series name  
FC  
Test conditions (conforming to JIS C 5160-1)  
5.5V type, 3.5V type  
Item  
Category temperature range  
－25℃ to ＋70℃  
MAX operating voltage  
Capacitance  
5.5Vdc, 3.5Vdc  
Refer to standard ratings  
＋80％, －20％  
Refer to “Measurement Conditions”  
Refer to “Measurement Conditions”  
Capacitance allowance  
Measured at 1kHz, 10mA ; See also “Measurement  
Conditions”  
ESR  
Refer to standard ratings  
Current (30-minutes value)  
Refer to standard ratings  
Refer to “Measurement Conditions”  
Surge voltage：4.0V (3.5V type, 3.6V type)  
：6.3V (5.5V type)  
Capacitance  
ESR  
More than 90% of initial ratings  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
Charge：30 sec.  
Discharge：9min 30sec.  
Current (30 minutes value)  
Number of cycles：1000  
Series resistance：0.043F, 0.047F 300Ω  
*
：0.068F  
：0.10F  
240Ω  
150Ω  
56Ω  
Surge  
：0.22F  
Appearance  
No obvious abnormality  
：0.47F  
：1.0F  
30Ω  
15Ω  
Discharge resistance：0Ω  
Temperature：70±2℃  
Capacitance  
ESR  
50% higher than initial value  
Phase 2  
400% or less than initial value  
Capacitance  
ESR  
Capacitance  
ESR  
Current (30 minutes value)  
Capacitance  
ESR  
Current (30 minutes value)  
Capacitance  
ESR  
Conforms to 4.17  
Phase 3  
Phase1：＋25±2℃  
Phase2：－25±2℃  
Phase4：＋25±2℃  
Phase5：＋70±2℃  
Phase6：＋25±2℃  
*
200% or less than initial value  
Characteristics in  
Phase 5  
Phase 6  
Satisfy initial ratings  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Satisfy initial ratings  
different temperature  
Conforms to 4.13  
Frequency：10 to 55 Hz  
Testing time：6 hours  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
*
Vibration resistance  
Current (30 minutes value)  
Appearance  
Capacitance  
ESR  
Current (30 minutes value)  
Cooled down to ambient temperature after reflow  
soldering, then the product must fulfill the condition  
stated left. (See page 10 for reflow condition)  
*
Solder heat resistance  
Appearance  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.12  
Temperature condition：－25℃→Room temperature→  
＋70℃→Room temperature  
Number of cycles：5 Cycles  
*
Temperature cycle  
Appearance  
No obvious abnormality  
Capacitance  
Within ±20% of initial value  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
No obvious abnormality  
Conforms to 4.14  
*
ESR  
Temperature：40±2℃  
Relative humidity：90 to 95％RH  
Testing time：240±8 hours  
High temp. and high  
Current (30 minutes value)  
Appearance  
humidity resistance  
Capacitance  
Within ±30% of initial value  
Below 200% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
Conforms to 4.15  
ESR  
Voltage applied：MAX operating voltage  
*
High temperature load  
Series protection resistance：0Ω  
Current (30 minutes value)  
Appearance  
＋48  
Testing time：1000 Hours  
ꢀ0  
Voltage applied：5.0Vdc (Terminal  
Charging  
condition  
at the case's side be negative)  
Series resistance：0Ω  
Charging time：24 hours  
5.5V type: Voltage between terminal leads  
higher than 4.2V  
3.5V type: Not specified  
*
Self discharge characteristics  
(voltage holding characteristics)  
Let stand for 24 hours in condition  
described below with terminals  
opened.  
Storage  
Ambient temperature：Lower than 25℃  
Relative humidity：Lower than 70%RH  
As for items with “*” , it must fulfill the above condition after the reflow soldering. (See page 10 for reflow conditions)  
12 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
6.2 FM Series  
Dimensions  
10.5±0.5  
T±0.5  
0.5±0.1  
5±0.5  
0.4±0.1  
（Unit：mm）  
Markings  
Negative polarity identification  
N T  
Nominal capacitance  
MAX operating  
voltage  
5.5V  
473  
E：FME type marking  
L ：FML type marking  
R：FMR type marking  
E
A1  
+
–
Date code  
Polarity  
Lead terminal forming example  
Lead length designation  
For transverse mounting ＜L1＞  
Ｌ＝2.2 to 5mm  
Super Capacitors Vol.12 13  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Specifications  
●5.5V Type  
Nominal  
capacitance  
MAX  
operating  
voltage  
（Vdc）  
Voltage  
holding  
Part Number  
MAX ESR  
（at 1 kHz）  
（Ω）  
MAX current  
at 30 min.  
（mA）  
T
Weight  
（g）  
characteristics （mm）  
Charge  
Discharge  
Bulk  
Ammo pack  
（V）  
system(F) system(F)  
0.01 0.014  
0.022 0.028  
0.047 0.06  
FM0H103ZF  
FM0H223ZF  
FM0H473ZF  
FM0H104ZF  
FM0H224ZF  
FM0H103ZFTP（ ）  
FM0H223ZFTP（ ）  
FM0H473ZFTP（ ）  
FM0H104ZFTP（ ）  
FM0H224ZFTP（ ）  
5.5  
5.5  
5.5  
5.5  
5.5  
300  
200  
200  
100  
100  
0.015  
0.033  
0.071  
0.15  
4.2  
4.2  
4.2  
4.2  
4.2  
5.0  
5.0  
5.0  
6.5  
6.5  
1.3  
1.3  
1.3  
1.6  
1.6  
0.10  
0.13  
0.22  
－
0.33  
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"  
●3.5V Type  
Nominal  
capacitance  
Part Number  
MAX operating  
voltage  
（Vdc）  
MAX ESR  
（at 1 kHz）  
（Ω）  
MAX current at  
T
Weight  
（g）  
30 min.  
（mA）  
（mm）  
Charge  
system(F)  
Discharge  
Bulk  
Ammo pack  
system(F)  
0.06  
0.13  
0.30  
FM0V473ZF  
FM0V104ZF  
FM0V224ZF  
FM0V473ZFTP（ ）  
FM0V104ZFTP（ ）  
FM0V224ZFTP（ ）  
3.5  
3.5  
3.5  
0.047  
0.10  
0.22  
200  
100  
100  
0.042  
0.090  
0.20  
5.0  
5.0  
6.5  
1.3  
1.3  
1.6  
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"  
●6.5V Type  
Nominal  
capacitance  
Part Number  
Ammo pack  
FM0J473ZFTP（ ）  
MAX operating  
voltage  
（Vdc）  
MAX ESR  
（at 1 kHz）  
（Ω）  
MAX current at  
30 min.  
T
Weight  
（g）  
（mm）  
Charge  
system(F)  
Discharge  
system(F)  
（mA）  
Bulk  
FM0J473ZF  
6.5  
0.047  
0.062  
200  
0.071  
6.5  
1.6  
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"  
●FME, FML Type (Buckup Large Current, mA Order)  
Nominal  
capacitance  
Part Number  
MAX operating  
voltage  
（Vdc）  
MAX ESR  
（at 1 kHz）  
（Ω）  
MAX current at  
30 min.  
T
Weight  
（mm）  
（g）  
Charge  
system(F)  
Discharge  
（mA）  
Bulk  
Ammo pack  
system(F)  
0.028  
0.06  
FME0H223ZF FME0H223ZFTP（ ）  
FME0H473ZF FME0H473ZFTP（ ）  
FML0H333ZF FML0H333ZFTP（ ）  
5.5  
5.5  
5.5  
0.022  
0.047  
40  
20  
0.033  
0.071  
0.050  
5.0  
5.0  
5.0  
1.3  
1.3  
1.3  
0.033  
6.5  
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"  
●FMR Type (MAX Operating Temperature 85℃ Type)  
Nominal  
MAX  
Voltage  
holding  
Part Number  
MAX ESR  
（at 1 kHz）  
（Ω）  
MAX current  
at 30 min.  
（mA）  
capacitance  
operating  
voltage  
（Vdc）  
T
Weight  
（g）  
characteristics （mm）  
Charge  
Discharge  
Bulk  
Ammo pack  
（V）  
system(F) system(F)  
0.047 0.062  
0.10  
FMR0H473ZF FMR0H473ZFTP（ ）  
FMR0H104ZF FMR0H104ZFTP（ ）  
FMR0V104ZF FMR0V104ZFTP（ ）  
5.5  
5.5  
3.5  
200  
50  
0.071  
0.15  
4.2  
4.2  
－
6.5  
6.5  
6.5  
1.6  
1.6  
1.6  
0.10  
50  
0.090  
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"  
14 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
●FMC Type  
Chip parts applicable to treatment in bond hardening furnace (160±5℃ for 120±10 seonds)  
Dimensions  
b ±0.5  
T±0.5  
d1 ±0.1  
d2 ±0.1  
5±0.5  
（Unit：mm）  
Markings  
Negative polarity identification  
N T  
Nominal capacitance  
MAX operating  
voltage  
5.5V  
473  
C：FMC type marking  
C
K1  
+
–
Date code  
Polarity  
Specifications  
Nominal  
capacitance  
MAX  
operating  
voltage  
（Vdc）  
MAX  
Voltage  
holding  
characteristics  
（V）  
Part Number  
MAX ESR  
（at 1 kHz）  
（Ω）  
a
b
T
d1  
d2  
Weight  
current at  
30 min.  
（mA）  
Charge  
Discharge  
(mm) (mm) (mm) (mm) (mm)  
（g）  
Bulk  
Ammo pack  
system(F) system(F)  
FMC0H473ZF FMC0H473ZFTP（ ）  
FMC0H104ZF FMC0H104ZFTP（ ）  
FMC0H334ZF FMC0H334ZFTP（ ）  
5.5  
5.5  
5.5  
0.047 0.06  
100  
50  
0.071  
0.15  
0.50  
4.2  
4.2  
4.2  
11.5 10.5 5.0  
11.5 10.5 6.5  
15.0 14.0 9.0  
0.5  
0.5  
0.6  
0.4  
0.4  
0.6  
1.3  
1.6  
3.5  
0.10  
–
0.13  
0.33  
25  
To complete the part number, insert lead length (16mm or 18mm) in to the "( )"  
Super Capacitors Vol.12 15  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Taping Specification [except FMC0H334ZFTP( )]  
P2  
P
Δh  
b
c
－
＋
－
＋
P1  
F
W4  
H
t3  
t2  
P0  
D0  
t1  
（Unit：mm）  
Item  
Component Height  
Symbol  
Value  
11.5  
Tolerance  
±0.5  
Remarks  
a
b
Component Width  
10.5  
±0.5  
5.5 V type : 5.0/0.010F to 0.047F, 6.5/0.047F  
3.5 V type : 5.0/0.047F to 0.10F, 6.5/0.22F  
FME type : 5.0/0.022F to 0.047F  
FML type : 5.0/0.033F  
6.5 V type : 6.5/0.047F, 0.10F  
FMR type : 6.5/0.047F  
Component Thickness  
c
－
±0.5  
FMC type : 5.0/0.047F, 6.5/0.10F  
Lead-wire Width  
W4  
t3  
0.5  
0.4  
±0.1  
±0.1  
±1.0  
±0.3  
±0.7  
±1.3  
±0.5  
－
Lead-wire Thickness  
Pitch between Component  
Sprocket Hole Pitch  
Sprocket Hole to Lead  
〃
P
12.7  
12.7  
3.85  
6.35  
5.0  
P0  
P1  
P2  
F
Lead Spacing  
Component Alignment  
Δh  
2.0 Max.  
18.0  
Including tilting caused by bending lead wire.  
＋1.0  
－0.5  
Tape Width  
W
Hold-down tape Width  
Sprocket Hole Position  
Hold-down Tape Position  
Component's Bottom Line Position  
〃
W0  
W1  
W2  
12.5 Min.  
9.0  
－
±0.5  
－
3.0 Max.  
16.0  
No protrusion of tape.  
±0.5  
±0.5  
±0.2  
±0.2  
－
H
18.0  
Sprocket Hole Diameter  
Total tape Thickness  
〃
D0  
t1  
φ4.0  
0.7  
t2  
1.5 Max.  
11.0 Max.  
Defect Component Cut-off Position  
L
－
16 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Taping Specification [except FMC0H334ZFTP ( )]  
P2  
P
Δh  
b
c
－
＋
－
＋
P1  
F
W4  
t
t
3
2
D
0
P0  
t
1
（Unit：mm）  
Item  
Component Height  
Component Width  
Symbol  
Value  
15.0  
14.0  
9.0  
Tolerance  
±0.5  
±0.5  
±0.5  
±0.1  
±0.1  
±1.0  
±0.3  
±0.7  
±1.3  
±0.5  
－
Remarks  
a
b
Component Thickness  
Lead-wire Width  
c
W4  
t3  
0.6  
Lead-wire Thickness  
0.6  
Pitch between Component  
Sprocket Hole Pitch  
Sprocket Hole to Lead  
〃
P
25.4  
12.7  
3.85  
6.35  
5.0  
P0  
P1  
P2  
F
Lead Spacing  
Component Alignment  
Δh  
2.0 Max.  
Including tilting caused by bending lead wire  
＋1.0  
－0.5  
Tape Width  
W
18.0  
Hold-down tape Width  
Sprocket Hole Position  
Hold-down Tape Position  
W0  
W1  
W2  
12.5 Min.  
9.0  
－
±0.5  
－
3.0 Max.  
16.0  
No protrusion of tape  
Component's Bottom Line Position  
±0.5  
±0.5  
±0.2  
±0.2  
－
H
〃
Sprocket Hole Diameter  
Total tape Thickness  
〃
18.0  
D0  
t1  
φ4.0  
0.67  
t2  
1.7 Max.  
11.0 Max.  
Defect Component Cut-off Position  
L
－
Super Capacitors Vol.12 17  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Specifications  
Series name  
5.5V type, 3.5V type, 6.5V type  
FMC type  
Test conditions  
(conforming to JIS C 5160-1)  
FML, FME type  
－25℃ to ＋70℃  
Item  
Category temperature range  
－25℃ to ＋70℃  
MAX operating voltage  
5.5Vdc, 3.5Vdc, 6.5Vdc  
5.5Vdc  
5.5V：0.010F to 0.33F  
3.5V：0.047F to 0.22F  
6.5V：0.047  
Capacitance  
0.022F, 0.033F, 0.047F  
Refer to “Measurement Conditions”  
Refer to “Measurement Conditions”  
Measured at 1kHz, 10mA ; See also  
“Measurement Conditions”  
Capacitance allowance  
ESR  
＋80％, －20％  
＋80％, －20％  
Refer to standard ratings  
Refer to standard ratings  
Current (30-minutes value)  
Refer to standard ratings  
Refer to standard ratings  
Refer to “Measurement Conditions”  
Surge voltage：4.0V (3.5V type)  
Capacitance  
ESR  
More than 90% of initial ratings  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
More than 90% of initial ratings  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
：6.3V (5.5V type)  
：7.4V (6.5V type)  
Charge：30 sec.  
Current (30 minutes value)  
Discharge：9min 30sec.  
Number of cycles：1000  
Series resistance：0.010F  
：0.022F  
1500Ω  
560Ω  
510Ω  
300Ω  
240Ω  
150Ω  
56Ω  
Surge  
：0.033F  
：0.047F  
Appearance  
No obvious abnormality  
No obvious abnormality  
：0.068F  
：0.10F  
：0.22F  
：0.33F  
51Ω  
Discharge resistance：0Ω  
Temperature：70±2℃  
Capacitance  
ESR  
50% or higher than initial value  
400% or less than initial value  
50% or higher than initial value  
400% or less than initial value  
Phase  
2
Phase  
2
Capacitance  
ESR  
Capacitance  
ESR  
Current (30 minutes value)  
Capacitance  
ESR  
Phase  
3
Phase  
3
Conforms to 4.17  
Phase1：＋25±2℃  
Phase2：－25±2℃  
Phase4：＋25±2℃  
Phase5：＋70±2℃  
Phase6：＋25±2℃  
Characteristics  
in different  
temperature  
200% or less than initial value  
Satisfy initial ratings  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Satisfy initial ratings  
200% or less than initial value  
Satisfy initial ratings  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Satisfy initial ratings  
Phase  
5
Phase  
5
Phase  
6
Phase  
6
Current (30 minutes value)  
Lead strength (tensile)  
Capacitance  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
Conforms to 4.9  
Conforms to 4.13  
ESR  
Vibration  
Frequency：10 to 55 Hz  
Current (30 minutes value)  
resistance  
Testing time：6 hours  
Appearance  
Conforms to 4.11  
Over 3/4 of the terminal should  
be covered by the new solder  
Over 3/4 of the terminal should  
be covered by the new solder  
Solder temp：245±5℃  
Solderability  
Dipping time：5±0.5 sec.  
1.6mm from the bottom should be dipped.  
Capacitance  
ESR  
Conforms to 4.10  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
Solder heat  
resistance  
Solder temp：260±10℃  
Dipping time：10±1 sec.  
1.6mm from the bottom should be dipped.  
Current (30 minutes value)  
Appearance  
Capacitance  
ESR  
Conforms to 4.12  
Temperature condition：－25℃→Room temperature→  
Temperature  
cycle  
Current (30 minutes value)  
＋70℃→Room temperature  
Number of cycles：5 Cycles  
Appearance  
Capacitance  
ESR  
No obvious abnormality  
No obvious abnormality  
Within ±20% of initial value  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
No obvious abnormality  
Within ±20% of initial value  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
No obvious abnormality  
Conforms to 4.14  
High temp. and  
high humidity  
resistance  
Temperature：40±2℃  
Relative humidity：90 to 95％RH  
Testing time：240±8 hours  
Current (30 minutes value)  
Appearance  
Capacitance  
ESR  
Within ±30% of initial value  
Below 200% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
Within ±30% of initial value  
Below 200% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
Conforms to 4.15  
High  
temperature  
load  
Temperature：70±2℃  
Voltage applied：MAX operating voltage  
Current (30 minutes value)  
Appearance  
Series protection resistance：0Ω  
＋48  
Testing time：1000 Hours  
ꢀ0  
Voltage applied：5.0Vdc (Terminal at  
Charging the case's side be negative)  
condition Series resistance：0Ω  
Charging time：24 hours  
5.5V type: Voltage between  
terminal leads higher  
than 4.2V  
3.5V type: Not specified  
6.5V type: Not specified  
Self discharge characteristics  
(voltage holding characteristics)  
Let stand for 24 hours in condition  
described below with terminals opened.  
Ambient temperature：Lower than 25℃  
Storage  
Relative humidity：Lower than 70%RH  
18 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Specifications  
Series name  
FMR type  
Test conditions (conforming to JIS C 5160-1)  
Item  
Category temperature range  
－40℃ to ＋85℃  
5.5Vdc, 3.5Vdc  
0.047F, 0.10F  
MAX operating voltage  
Capacitance  
Refer to “Measurement Conditions”  
Refer to “Measurement Conditions”  
Capacitance allowance  
＋80％, －20％  
Measured at 1kHz, 10mA ; See also “Measurement  
Conditions”  
ESR  
Refer to standard ratings  
Current (30-minutes value)  
Refer to standard ratings  
Refer to “Measurement Conditions”  
Surge voltage：4.0V (3.5V type)  
：6.3V (5.5V type)  
Capacitance  
ESR  
More than 90% of initial ratings  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
Charge：30 sec.  
Current (30 minutes value)  
Discharge：9min 30sec.  
Number of cycles：1000  
Series resistance：0.047F 300Ω  
Surge  
：0.10F  
Discharge resistance：0Ω  
Temperature：85±2℃  
150Ω  
Appearance  
No obvious abnormality  
Capacitance  
ESR  
Capacitance  
ESR  
Capacitance  
ESR  
Current (30 minutes value)  
Capacitance  
ESR  
50% or higher than initial value  
Phase 2  
Phase 3  
400% or less than initial value  
30% or higher than initial value  
Below 700% of the initial value  
200% or less than initial value  
Satisfy initial ratings  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Conforms to 4.17  
Phase1：＋25±2℃  
Phase2：－25±2℃  
Phase3：－40±2℃  
Phase4：＋25±2℃  
Phase5：＋70±2℃  
Phase6：＋25±2℃  
Characteristics in  
different temperature  
Phase 5  
Phase 6  
Current (30 minutes value)  
Satisfy initial ratings  
Lead strength (tensile)  
Vibration resistance  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
Conforms to 4.9  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.13  
Frequency：10 to 55 Hz  
Testing time：6 hours  
Appearance  
Conforms to 4.11  
Over 3/4 of the terminal should be covered by  
the new solder  
Solder temp：245±5℃  
Solderability  
Dipping time：5±0.5 sec.  
1.6mm from the bottom should be dipped.  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.10  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
Solder temp：260±10℃  
Dipping time：10±1 sec.  
1.6mm from the bottom should be dipped.  
Solder heat resistance  
Appearance  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.12  
Temperature condition：－40℃→Room temperature→  
＋85℃→Room temperature  
Number of cycles：5 Cycles  
Temperature cycle  
Appearance  
No obvious abnormality  
Capacitance  
Within ±20% of initial value  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
No obvious abnormality  
Conforms to 4.14  
ESR  
High temp. and high  
humidity resistance  
Temperature：40±2℃  
Relative humidity：90 to 95％RH  
Testing time：240±8 hours  
Current (30 minutes value)  
Appearance  
Capacitance  
Within ±30% of initial value  
Below 200% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
Conforms to 4.15  
Temperature：85±2℃  
ESR  
High temperature load  
Voltage applied：MAX operating voltage  
Current (30 minutes value)  
Appearance  
Series protection resistance：0Ω  
＋48  
Testing time：1000 Hours  
ꢀ0  
Voltage applied：5.0Vdc (Terminal  
Charging  
condition  
at the case's side be negative)  
Series resistance：0Ω  
Charging time：24 hours  
5.5V type: Voltage between terminal leads  
higher than 4.2V  
3.5V type: Not specified  
Self discharge characteristics  
(voltage holding characteristics)  
Let stand for 24 hours in condition  
described below with terminals  
opened.  
Storage  
Ambient temperature：Lower than 25℃  
Relative humidity：Lower than 70%RH  
Super Capacitors Vol.12 19  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
6.3 FG Series  
Dimensions  
Markings on sleeve  
F
D ± 0.5  
MAX  
A1  
Super Capacitor  
FG 5.5 V  
0.22 F  
Date  
code  
operating  
voltage  
001 FG 5.5 V  
Serial  
number  
Nominal  
capacitance  
Sleeve  
A1  
0.22 F  
P ± 0.5  
Negative polarity  
identification mark  
○－ ○＋  
d
1
2
± 0.1  
± 0.1  
d
（Terminal）  
●FG Type  
Specifications  
MAX  
operating  
voltage  
（Vdc）  
Nominal capacitance  
MAX  
current at  
30 min.  
（mA）  
Voltage  
Dimension (unit:mm)  
MAX ESR  
（at 1 kHz）  
（Ω）  
Weight  
holding  
characteristics  
（V）  
Part Number  
Charge  
Discharge  
φD  
H
P
ℓ
d1  
d2  
（g）  
system (F) system (F)  
FG0H103ZF  
FG0H223ZF  
FG0H473ZF  
FG0H104ZF  
FG0H224ZF  
FG0H474ZF  
FG0H105ZF  
FG0H225ZF  
FG0H475ZF  
FG0V155ZF  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
3.5  
0.010  
0.022  
0.047  
0.10  
0.22  
0.47  
1.0  
0.013  
0.028  
0.060  
0.13  
0.28  
0.60  
1.3  
300  
200  
200  
100  
100  
120  
65  
0.015  
0.033  
0.071  
0.15  
0.33  
0.71  
1.5  
4.2  
4.2  
4.2  
4.2  
4.2  
4.2  
4.2  
4.2  
4.2  
－
11.0  
11.0  
11.0  
11.0  
13.0  
14.5  
16.5  
21.5  
28.5  
16.5  
5.5  
5.5  
5.08  
5.08  
5.08  
5.08  
5.08  
5.08  
5.08  
7.62  
2.7  
2.7  
2.7  
2.7  
2.2  
2.4  
2.7  
3.0  
6.1  
3.1  
0.2  
0.2  
0.2  
0.2  
0.4  
0.4  
0.4  
0.6  
0.6  
0.4  
1.2  
1.2  
1.2  
1.2  
1.2  
1.2  
1.2  
1.2  
1.4  
1.2  
0.9  
1.0  
1.0  
1.3  
2.5  
5.1  
7.0  
12.1  
27.3  
5.2  
5.5  
6.5  
9.0  
18.0  
19.0  
19.0  
2.2  
2.8  
35  
3.3  
4.7  
6.0  
35  
7.1  
22.0 10.16  
14.0 5.08  
1.5  
2.2  
65  
1.5  
●FGH Type  
Specifications  
MAX  
operating  
voltage  
（Vdc）  
MAX  
Voltage  
holding  
characteristics  
（V）  
Dimension (unit:mm)  
Nominal capacitance  
MAX ESR  
（at 1 kHz）  
（Ω）  
Weight  
current at  
30 min.  
（mA）  
Part Number  
Charge  
Discharge  
φD  
H
P
ℓ
d1  
d2  
（g）  
system (F) system (F)  
FGH0H104ZF  
FGH0H224ZF  
FGH0H474ZF  
FGH0H105ZF  
5.5  
5.5  
5.5  
5.5  
－
－
－
－
0.10  
0.22  
0.47  
1.0  
100  
100  
65  
0.15  
0.33  
0.71  
1.5  
4.2  
4.2  
4.2  
4.2  
11.0  
11.0  
16.5  
21.5  
5.5  
7.0  
8.0  
9.5  
5.08  
5.08  
5.08  
7.62  
2.7  
2.7  
2.7  
3.0  
0.2  
0.2  
0.4  
0.6  
1.2  
1.2  
1.2  
1.2  
1.0  
1.3  
4.1  
7.2  
35  
●FGR Type  
Specifications  
MAX  
operating  
voltage  
（Vdc）  
Nominal capacitance  
MAX  
Voltage  
holding  
characteristics  
（V）  
Dimension (unit:mm)  
MAX ESR  
（at 1 kHz）  
（Ω）  
Weight  
current at  
30 min.  
（mA）  
Part Number  
Charge  
Discharge  
φD  
H
P
ℓ
d1  
d2  
（g）  
system (F) system (F)  
FGR0H474ZF  
FGR0H105ZF  
FGR0H225ZF  
5.5  
5.5  
5.5  
0.47  
1.0  
0.60  
1.3  
120  
65  
0.71  
4.2  
4.2  
4.2  
14.5  
16.5  
21.5  
18.0  
19.0  
19.0  
5.08  
5.08  
7.62  
2.4  
2.7  
3.0  
0.4  
0.4  
0.6  
1.2  
1.2  
1.2  
5.1  
7.0  
1.5  
2.2  
2.8  
35  
3.3  
12.1  
20 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Specifications  
Series name  
Test conditions  
(conforming to JIS C 5160-1)  
FG, FGH type  
－25℃ to ＋70℃  
FGR type  
－40℃ to ＋85℃  
Item  
Category temperature range  
MAX operating voltage  
5.5Vdc, 3.5Vdc  
5.5Vdc  
FG：0.010F to 4.7F  
Capacitance  
0.47F to 2.2F  
Refer to “Measurement Conditions”  
Refer to “Measurement Conditions”  
Measured at 1kHz, 10mA ; See also  
“Measurement Conditions”  
FGH：0.10F to 1.0F  
Capacitance allowance  
ESR  
＋80％, －20％  
＋80％, －20％  
Refer to standard ratings  
Refer to standard ratings  
Current (30-minutes value)  
Refer to standard ratings  
Refer to standard ratings  
Refer to “Measurement Conditions”  
Surge voltage：6.3V (5.5V type)  
Capacitance  
ESR  
More than 90% of initial ratings  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
More than 90% of initial ratings  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
：4.0V(3.5V type)  
Charge：30 sec.  
Current (30 minutes value)  
Discharge：9min 30sec.  
Number of cycles：1000  
Series resistance ：0.010F  
：0.022F  
1500Ω  
560Ω  
300Ω  
150Ω  
56Ω  
：0.047F  
Surge  
：0.10F  
：0.22F  
Appearance  
No obvious abnormality  
No obvious abnormality  
：0.47F  
30Ω  
：1.0F, 1.5F  
15Ω  
：2.2F, 4.7F  
10Ω  
Discharge resistance：0Ω  
Temperature：85±2℃ (FGR)  
：70±2℃ (FG, FGH)  
Capacitance  
ESR  
50% or higher than initial value  
400% or less than initial value  
50% or higher than initial value  
400% or less than initial value  
30% or higher than initial value  
700% or less than initial value  
200% or less than initial value  
Satisfy initial ratings  
Phase  
2
Phase  
2
Conforms to 4.17  
Capacitance  
ESR  
Phase  
3
Phase  
3
Phase1：＋25±2℃  
Phase2：－25±2℃  
Phase3：－40±2℃ (FGR)  
Phase4：＋25±2℃  
Phase5：＋70±2℃ (FG, FGH)  
：＋85±2℃ (FGR)  
Characteristics  
in different  
temperature  
Capacitance  
ESR  
200% or less than initial value  
Satisfy initial ratings  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Satisfy initial ratings  
Phase  
5
Phase  
5
Current (30 minutes value)  
Capacitance  
ESR  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Phase6：＋25±2℃  
Phase  
6
Phase  
6
Current (30 minutes value)  
Satisfy initial ratings  
Lead strength (tensile)  
Capacitance  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
Conforms to 4.9  
Conforms to 4.13  
ESR  
Vibration  
Frequency：10 to 55 Hz  
resistance  
Current (30 minutes value)  
Appearance  
Testing time：6 hours  
Conforms to 4.11  
Over 3/4 of the terminal should  
be covered by the new solder  
Over 3/4 of the terminal should  
be covered by the new solder  
Solder temp：245±5℃  
Solderability  
Dipping time：5±0.5 sec.  
1.6mm from the bottom should be dipped.  
Capacitance  
ESR  
Conforms to 4.10  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
Solder heat  
resistance  
Solder temp：260±10℃  
Dipping time：10±1 sec.  
1.6mm from the bottom should be dipped.  
Current (30 minutes value)  
Appearance  
Capacitance  
ESR  
Conforms to 4.12  
Temperature condition：Category MIN temp→Room temp→  
Temperature  
cycle  
Category MAX temp→Room temp  
Current (30 minutes value)  
Appearance  
Capacitance  
Number of cycles：5 Cycles  
No obvious abnormality  
No obvious abnormality  
Within ±20% of initial value  
Within ±20% of initial value  
Not to exceed 120% of initial  
ratings  
Not to exceed 120% of initial  
ratings  
Not to exceed 120% of initial  
ratings  
Not to exceed 120% of initial  
ratings  
Conforms to 4.14  
ESR  
High temp. and  
high humidity  
resistance  
Temperature：40±2℃  
Relative humidity：90 to 95％RH  
Testing time：240±8 hours  
Current (30 minutes value)  
Appearance  
Capacitance  
ESR  
No obvious abnormality  
No obvious abnormality  
Conforms to 4.15  
Within ±30% of initial value  
Below 200% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
Within ±30% of initial value  
Below 200% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
High  
temperature  
load  
Temp：Category MAX temp ±2℃  
Voltage applied：MAX operating voltage  
Current (30 minutes value)  
Appearance  
Series protection resistance：0Ω  
＋48  
Testing time：1000 Hours  
ꢀ0  
Voltage applied：5.0Vdc (Terminal at  
Charging the case's side be negative)  
condition Series resistance：0Ω  
Charging time：24 hours  
5.5V type: Voltage between  
terminal leads higher  
than 4.2V  
Self discharge characteristics  
(voltage holding characteristics)  
Voltage between terminal leads  
higher than 4.2V  
Let stand for 24 hours in condition  
3.5V type: Not specified  
described below with terminals opened.  
Storage  
Ambient temperature：Lower than 25℃  
Relative humidity：Lower than 70%RH  
Super Capacitors Vol.12 21  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
6.4 FT Series  
Dimensions  
Markings on sleeve  
F
D ± 0.5  
A1  
Super Capacitor  
FT 5.5 V  
Date  
code  
MAX  
operating voltage  
001 FT 5.5 V  
A1 85℃ 0.22 F  
Serial  
number  
Nominal  
85℃ 0.22 F  
capacitance  
Sleeve  
Negative polarity  
identification mark  
P ± 0.5  
○－ ○＋  
d
d
1
2
± 0.1  
± 0.1  
（Terminal）  
Specifications  
MAX  
operating  
voltage  
（Vdc）  
Nominal capacitance  
Dimension (unit:mm)  
MAX ESR MAX current  
Weight  
Part Number  
（at 1 kHz） at 30 min.  
Charge  
Discharge  
system (F)  
φD  
H
P
d1  
d2  
ℓ
（Ω）  
（mA）  
（g）  
system (F)  
FT0H104ZF  
FT0H224ZF  
FT0H474ZF  
FT0H105ZF  
FT0H225ZF  
FT0H335ZF  
FT0H565ZF  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
0.10  
0.22  
0.47  
1.0  
0.14  
0.28  
0.60  
1.3  
16  
10  
0.15  
0.33  
0.71  
1.5  
11.5  
14.5  
16.5  
21.5  
28.5  
36.5  
44.5  
8.5  
5.08  
5.08  
5.08  
7.62  
0.4  
0.4  
0.4  
0.6  
0.6  
0.6  
1.0  
1.2  
1.2  
1.2  
1.2  
1.4  
1.7  
1.4  
2.7  
2.2  
2.7  
3.0  
6.1  
6.1  
6.1  
1.6  
4.1  
12.0  
13.0  
13.0  
6.5  
3.5  
1.8  
1.0  
0.6  
5.3  
10.0  
18.0  
38.0  
72.0  
2.2  
2.8  
3.3  
14.0 10.16  
15.0 15.00  
17.0 20.00  
3.3  
4.2  
5.0  
5.6  
7.2  
8.4  
22 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Specifications  
Series name  
FT type  
Test conditions (conforming to JIS C 5160-1)  
Item  
Category temperature range  
－40℃ to ＋85℃  
5.5Vdc  
MAX operating voltage  
Capacitance  
0.1F to 5.6F  
＋80％, －20％  
Refer to “Measurement Conditions”  
Refer to “Measurement Conditions”  
Capacitance allowance  
Measured at 1kHz, 10mA ; See also “Measurement  
Conditions”  
ESR  
Refer to standard ratings  
Current (30-minutes value)  
Refer to standard ratings  
Refer to “Measurement Conditions”  
Capacitance  
ESR  
Current (30 minutes value)  
More than 90% of initial ratings  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
Surge voltage：6.3V  
Charge：30 sec.  
Discharge：9min 30sec.  
Number of cycles：1000  
Series resistance：0.10F  
：0.22F  
150Ω  
56Ω  
30Ω  
15Ω  
10Ω  
10Ω  
10Ω  
Surge  
：0.47F  
：1.0F  
Appearance  
No obvious abnormality  
：2.2F  
：3.3F  
：5.6F  
Discharge resistance：0Ω  
Temperature：85±2℃  
Capacitance  
ESR  
Capacitance  
ESR  
Capacitance  
ESR  
Current (30 minutes value)  
Capacitance  
ESR  
50% or higher than initial value  
Phase 2  
Phase 3  
400% or less than initial value  
30% or higher than initial value  
700% or less than initial value  
200% or less than initial value  
Satisfy initial ratings  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Conforms to 4.17  
Phase1：＋25±2℃  
Phase2：－25±2℃  
Phase3：－40±2℃  
Phase4：＋25±2℃  
Phase5：＋70±2℃  
Phase6：＋25±2℃  
Characteristics in  
different temperature  
Phase 5  
Phase 6  
Current (30 minutes value)  
Satisfy initial ratings  
Lead strength (tensile)  
Vibration resistance  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
Conforms to 4.9  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.13  
Frequency：10 to 55 Hz  
Testing time：6 hours  
Appearance  
Conforms to 4.11  
Over 3/4 of the terminal should be covered by  
the new solder  
Solder temp：245±5℃  
Solderability  
Dipping time：5±0.5 sec.  
1.6mm from the bottom should be dipped.  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.10  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
Solder temp：260±10℃  
Dipping time：10±1 sec.  
1.6mm from the bottom should be dipped.  
Solder heat resistance  
Appearance  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.12  
Temperature condition：－40℃→Room temperature→  
＋85℃→Room temperature  
Number of cycles：5 Cycles  
Temperature cycle  
Appearance  
No obvious abnormality  
Capacitance  
Within ±20% of initial value  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
No obvious abnormality  
Conforms to 4.14  
ESR  
High temp. and high  
humidity resistance  
Temperature：40±2℃  
Relative humidity：90 to 95％RH  
Testing time：240±8 hours  
Current (30 minutes value)  
Appearance  
Capacitance  
Within ±30% of initial value  
Below 200% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
Conforms to 4.15  
Temperature：85±2℃  
ESR  
High temperature load  
Voltage applied：MAX operating voltage  
Current (30 minutes value)  
Appearance  
Series protection resistance：0Ω  
＋48  
Testing time：1000 Hours  
ꢀ0  
Super Capacitors Vol.12 23  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
6.5 FY Series  
Dimensions  
Markings on sleeve  
F
D ± 0.5  
A1  
MAX  
Date  
operating voltage  
code  
001 FYD 5.5 V  
FYD 5.5 V  
0.047 F  
0.047 F  
Nominal  
capacitance  
Serial  
number  
A1  
Sleeve  
P ± 0.5  
Negative polarity  
identification mark  
○－ ○＋  
d
1
2
± 0.1  
± 0.1  
d
（Terminal）  
●FYD Type  
Specifications  
MAX  
operating  
voltage  
（Vdc）  
Nominal capacitance  
MAX  
Voltage  
holding  
characteristics  
（V）  
Dimension (unit:mm)  
MAX ESR  
（at 1 kHz）  
（Ω）  
Weight  
current at  
30 min.  
（mA）  
Part Number  
Charge  
Discharge  
φD  
H
P
ℓ
d1  
d2  
（g）  
system (F) system (F)  
FYD0H223ZF  
FYD0H473ZF  
FYD0H104ZF  
FYD0H224ZF  
FYD0H474ZF  
FYD0H105ZF  
FYD0H145ZF  
FYD0H225ZF  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
0.022  
0.047  
0.10  
0.22  
0.47  
1.0  
0.033  
0.070  
0.14  
0.35  
0.75  
1.6  
220  
220  
100  
120  
65  
0.033  
0.071  
0.15  
0.33  
0.71  
1.5  
4.2  
4.2  
4.2  
4.2  
4.2  
4.2  
4.2  
4.2  
11.5  
11.5  
13.0  
14.5  
16.5  
21.5  
21.5  
28.5  
8.5  
8.5  
5.08  
5.08  
5.08  
5.08  
5.08  
7.62  
7.62  
2.7  
2.7  
2.2  
2.4  
2.7  
3.0  
3.0  
6.1  
0.4  
0.4  
0.4  
0.4  
0.4  
0.6  
0.6  
0.6  
1.2  
1.2  
1.2  
1.2  
1.2  
1.2  
1.2  
1.4  
1.6  
1.7  
8.5  
2.4  
15.0  
15.0  
16.0  
19.0  
4.3  
6.0  
35  
11.0  
12.0  
22.9  
1.4  
2.1  
45  
2.1  
2.2  
3.3  
35  
3.3  
22.0 10.16  
●FYH Type  
Specifications  
MAX  
operating  
voltage  
（Vdc）  
MAX  
Voltage  
holding  
characteristics  
（V）  
Dimension (unit:mm)  
Nominal capacitance  
MAX ESR  
（at 1 kHz）  
（Ω）  
Weight  
current at  
30 min.  
（mA）  
Part Number  
Charge  
Discharge  
φD  
H
P
ℓ
d1  
d2  
（g）  
system (F) system (F)  
FYH0H223ZF  
FYH0H473ZF  
FYH0H104ZF  
FYH0H224ZF  
FYH0H474ZF  
FYH0H105ZF  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
0.022  
0.047  
0.10  
0.22  
0.47  
1.0  
0.033  
0.075  
0.16  
0.30  
0.70  
1.5  
200  
100  
50  
0.033  
0.071  
0.15  
0.33  
0.71  
1.5  
4.2  
4.2  
4.2  
4.2  
4.2  
4.2  
11.5  
13.0  
16.5  
16.5  
21.5  
28.5  
7.0  
7.0  
5.08  
5.08  
5.08  
5.08  
7.62  
2.7  
2.2  
2.7  
2.7  
3.0  
6.1  
0.4  
0.4  
0.4  
0.4  
0.6  
0.6  
1.2  
1.2  
1.2  
1.2  
1.2  
1.4  
1.5  
2.2  
3.4  
3.6  
7.2  
13.9  
7.5  
60  
9.5  
35  
10.0  
20  
11.0 10.16  
●FGL Type  
Specifications  
MAX  
operating  
voltage  
（Vdc）  
Nominal capacitance  
MAX  
Voltage  
holding  
characteristics  
（V）  
Dimension (unit:mm)  
MAX ESR  
（at 1 kHz）  
（Ω）  
Weight  
current at  
30 min.  
（mA）  
Part Number  
Charge  
Discharge  
φD  
H
P
ℓ
d1  
d2  
（g）  
system (F) system (F)  
FYL0H103ZF  
FYL0H223ZF  
FYL0H473ZF  
5.5  
5.5  
5.5  
0.01  
0.022  
0.047  
0.013  
0.028  
0.061  
300  
200  
200  
0.015  
0.033  
0.071  
4.2  
4.2  
4.2  
11.0  
11.0  
12.0  
5.0  
5.0  
5.0  
5.08  
5.08  
5.08  
2.7  
2.7  
2.7  
0.2  
0.2  
0.2  
1.2  
1.2  
1.2  
0.9  
1.0  
1.2  
24 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Specifications  
Series name  
FY type (FYD, FYH, FYL)  
－25℃ to ＋70℃  
Test conditions (conforming to JIS C 5160-1)  
Item  
Category temperature range  
MAX operating voltage  
Capacitance  
5.5Vdc  
Refer to standard ratings  
Refer to “Measurement Conditions”  
Refer to “Measurement Conditions”  
Capacitance allowance  
＋80％, －20％  
FYD：0.022F to 2.2F  
FYH：0.022F to 1.0F  
FYL：0.010F to 0.047F  
Measured at 1kHz, 10mA ; See also “Measurement  
Conditions”  
ESR  
Current (30-minutes value)  
Refer to standard ratings  
Refer to “Measurement Conditions”  
Surge voltage：6.3V  
Capacitance  
ESR  
More than 90% of initial ratings  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
Charge：30 sec.  
Discharge：9min 30sec.  
Number of cycles：1000  
Current (30 minutes value)  
Series resistance：0.010F  
：0.022F  
1500Ω  
560Ω  
300Ω  
240Ω  
150Ω  
56Ω  
：0.047F  
Surge  
：0.068F  
：0.10F  
：0.22F  
Appearance  
No obvious abnormality  
：0.47F  
30Ω  
：1.0F, 1.4F  
：2.2F  
15Ω  
10Ω  
Discharge resistance：0Ω  
Temperature：70±2℃  
Capacitance  
ESR  
Capacitance  
ESR  
Capacitance  
ESR  
Current (30 minutes value)  
Capacitance  
ESR  
50% or higher than initial value  
400% or less than initial value  
Phase 2  
Phase 3  
Conforms to 4.17  
Phase1：＋25±2℃  
Phase2：－25±2℃  
Phase4：＋25±2℃  
Phase5：＋70±2℃  
Phase6：＋25±2℃  
200% or less than initial value  
Satisfy initial ratings  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Characteristics in  
different temperature  
Phase 5  
Phase 6  
Current (30 minutes value)  
Satisfy initial ratings  
Lead strength (tensile)  
Vibration resistance  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
Conforms to 4.9  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.13  
Frequency：10 to 55 Hz  
Testing time：6 hours  
Appearance  
Conforms to 4.11  
Over 3/4 of the terminal should be covered by  
the new solder  
Solder temp：245±5℃  
Solderability  
Dipping time：5±0.5 sec.  
1.6mm from the bottom should be dipped.  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.10  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
Solder temp：260±10℃  
Dipping time：10±1 sec.  
1.6mm from the bottom should be dipped.  
Solder heat resistance  
Appearance  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.12  
Temperature condition：－25℃→Room temperature→  
Temperature cycle  
＋70℃→Room temperature  
Number of cycles：5 Cycles  
Appearance  
No obvious abnormality  
Capacitance  
Within ±20% of initial value  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
No obvious abnormality  
Conforms to 4.14  
ESR  
High temp. and high  
humidity resistance  
Temperature：40±2℃  
Relative humidity：90 to 95％RH  
Testing time：240±8 hours  
Current (30 minutes value)  
Appearance  
Capacitance  
Within ±30% of initial value  
Below 200% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
Conforms to 4.15  
Temperature：70±2℃  
ESR  
High temperature load  
Voltage applied：MAX operating voltage  
Current (30 minutes value)  
Appearance  
Series protection resistance：0Ω  
＋48  
Testing time：1000 Hours  
ꢀ0  
Voltage applied：5.0Vdc (Terminal  
Charging  
condition  
at the case's side be negative)  
Series resistance：0Ω  
Charging time：24 hours  
Let stand for 24 hours in condition  
Self discharge characteristics  
(voltage holding characteristics)  
Voltage between terminal leads higher than 4.2V  
described below with terminals opened.  
Ambient temperature：Lower than 25℃  
Relative humidity：Lower than 70%RH  
Storage  
Super Capacitors Vol.12 25  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
6.6 FR Series  
Dimensions  
Markings on sleeve  
F
D ± 0.5  
A1  
Date  
code  
MAX  
operating voltage  
001 FR  
5.5 V  
FR  
5.5 V  
Serial  
number  
Nominal  
capacitance  
85℃ 0.022 F  
85℃ 0.022 F  
A1  
Sleeve  
Negative polarity  
identification mark  
P ± 0.5  
○－ ○＋  
d
1
2
± 0.1  
± 0.1  
d
（Terminal）  
Specifications  
MAX  
operating  
voltage  
（Vdc）  
Nominal capacitance  
MAX  
current at  
30 min.  
（mA）  
Voltage  
Dimension (unit:mm)  
MAX ESR  
（at 1 kHz）  
（Ω）  
Weight  
holding  
characteristics  
（V）  
Part Number  
Charge  
Discharge  
φD  
H
P
ℓ
d1  
d2  
（g）  
system (F) system (F)  
FR0H223ZF  
FR0H473ZF  
FR0H104ZF  
FR0H224ZF  
FR0H474ZF  
FR0H105ZF  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
0.022  
0.047  
0.10  
0.22  
0.47  
1.0  
0.028  
0.060  
0.15  
0.33  
0.75  
1.6  
220  
110  
150  
180  
100  
60  
0.033  
0.071  
0.15  
0.33  
0.71  
1.5  
4.2  
4.2  
4.2  
4.2  
4.2  
4.2  
11.5  
14.5  
14.5  
14.5  
16.5  
21.5  
14.0  
14.0  
15.5  
21.0  
21.5  
22.0  
5.08  
5.08  
5.08  
5.08  
5.08  
7.62  
2.7  
2.4  
2.4  
2.4  
2.7  
3.0  
0.4  
0.4  
0.4  
0.4  
0.4  
0.6  
1.2  
1.2  
1.2  
1.2  
1.2  
1.2  
2.3  
3.9  
4.3  
5.3  
7.5  
13.3  
26 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Specifications  
Series name  
FR type  
Test conditions (conforming to JIS C 5160-1)  
Item  
Category temperature range  
－40℃ to ＋85℃  
5.5Vdc  
MAX operating voltage  
Capacitance  
0.022F to 1.0F  
＋80％, －20％  
Refer to “Measurement Conditions”  
Refer to “Measurement Conditions”  
Capacitance allowance  
Measured at 1kHz, 10mA ; See also “Measurement  
Conditions”  
ESR  
Refer to standard ratings  
Current (30-minutes value)  
Refer to standard ratings  
Refer to “Measurement Conditions”  
Capacitance  
ESR  
Current (30 minutes value)  
More than 90% of initial ratings  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
Surge voltage：6.3V (5.5V type)  
Charge：30 sec.  
Discharge：9min 30sec.  
Number of cycles：1000  
Series resistance：0.022F  
：0.047F  
560Ω  
300Ω  
240Ω  
150Ω  
56Ω  
Surge  
：0.068F  
：0.10F  
Appearance  
No obvious abnormality  
：0.22F  
：0.47F  
30Ω  
：1.0F  
15Ω  
Discharge resistance：0Ω  
Temperature：70±2℃  
Capacitance  
ESR  
Capacitance  
ESR  
Capacitance  
ESR  
Current (30 minutes value)  
Capacitance  
ESR  
50% or higher than initial value  
Phase 2  
Phase 3  
400% or less than initial value  
30% or higher than initial value  
700% or less than initial value  
200% or less than initial value  
Satisfy initial ratings  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Conforms to 4.17  
Phase1：＋25±2℃  
Phase2：－25±2℃  
Phase3：－40±2℃  
Phase4：＋25±2℃  
Phase5：＋70±2℃  
Phase6：＋25±2℃  
Characteristics in  
different temperature  
Phase 5  
Phase 6  
Current (30 minutes value)  
Satisfy initial ratings  
Lead strength (tensile)  
Vibration resistance  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
Conforms to 4.9  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.13  
Frequency：10 to 55 Hz  
Testing time：6 hours  
Appearance  
Conforms to 4.11  
Over 3/4 of the terminal should be covered by  
the new solder  
Solder temp：245±5℃  
Solderability  
Dipping time：5±0.5 sec.  
1.6mm from the bottom should be dipped.  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.10  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
Solder temp：260±10℃  
Dipping time：10±1 sec.  
1.6mm from the bottom should be dipped.  
Solder heat resistance  
Appearance  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.12  
Temperature condition：－40℃→Room temperature→  
＋85℃→Room temperature  
Number of cycles：5 Cycles  
Temperature cycle  
Appearance  
No obvious abnormality  
Capacitance  
Within ±20% of initial value  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
No obvious abnormality  
Conforms to 4.14  
ESR  
High temp. and high  
humidity resistance  
Temperature：40±2℃  
Relative humidity：90 to 95％RH  
Testing time：240±8 hours  
Current (30 minutes value)  
Appearance  
Capacitance  
Within ±30% of initial value  
Below 200% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
Conforms to 4.15  
Temperature：85±2℃  
ESR  
High temperature load  
Voltage applied：MAX operating voltage  
Current (30 minutes value)  
Appearance  
Series protection resistance：0Ω  
＋48  
Testing time：1000 Hours  
ꢀ0  
Voltage applied：5.0Vdc (Terminal  
Charging  
condition  
at the case's side be negative)  
Series resistance：0Ω  
Charging time：24 hours  
Self discharge characteristics  
(voltage holding characteristics)  
Voltage between terminal leads higher than 4.2V  
Let stand for 24 hours in condition  
described below with terminals opened.  
Ambient temperature：Lower than 25℃  
Relative humidity：Lower than 70%RH  
Storage  
Super Capacitors Vol.12 27  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
6.7 FS Series  
Dimensions  
Markings on sleeve  
F
D ± 0.5  
Date  
code  
A1  
MAX  
operating voltage  
001 FS 5.5 V  
FS 5.5 V  
0.22 F  
Serial  
number  
Nominal  
capacitance  
A1  
0.22 F  
Sleeve  
Negative polarity  
identification mark  
P ± 0.5  
○－ ○＋  
d
1
2
± 0.1  
± 0.1  
d
（Terminal）  
Specifications  
MAX  
operating  
voltage  
（Vdc）  
Nominal capacitance  
Dimension (unit:mm)  
MAX ESR MAX current  
Weight  
Part Number  
（at 1 kHz） at 30 min.  
Charge  
Discharge  
system (F)  
φD  
H
P
ℓ
d1  
d2  
（Ω）  
（mA）  
（g）  
system (F)  
FS0H223ZF  
FS0H473ZF  
FS0H104ZF  
FS0H224ZF  
FS0H474ZF  
FS0H105ZF  
FS1A474ZF  
FS1A105ZF  
FS1B105ZF  
FS1B505ZF  
5.5  
0.022  
0.047  
0.10  
0.22  
0.47  
1.0  
0.033  
0.072  
0.15  
0.33  
0.75  
1.3  
60.0  
40.0  
25.0  
25.0  
13.0  
7.0  
0.033  
0.071  
0.15  
0.33  
0.71  
1.5  
11.5  
13.0  
16.5  
16.5  
21.5  
28.5  
28.5  
28.5  
28.5  
44.8  
8.5  
8.5  
5.08  
5.08  
5.08  
5.08  
7.62  
2.7  
2.2  
2.7  
2.7  
3.0  
6.1  
6.1  
6.1  
6.1  
9.5  
0.4  
0.4  
0.4  
0.4  
0.6  
0.6  
0.6  
0.6  
0.6  
1.0  
1.2  
1.2  
1.2  
1.2  
1.2  
1.4  
1.4  
1.4  
1.4  
1.4  
1.6  
2.6  
4.1  
5.3  
10  
5.5  
5.5  
8.5  
5.5  
13.0  
13.0  
5.5  
5.5  
14.0 10.16  
25.5 10.16  
31.5 10.16  
38.0 10.16  
60.0 20.00  
18  
11.0  
11.0  
12.0  
12.0  
0.47  
1.0  
0.60  
1.3  
7.0  
1.41  
3.0  
32  
7.0  
35  
1.0  
1.3  
7.5  
3.6  
40  
5.0  
6.5  
4.0  
18.0  
160  
28 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Specifications  
Series name  
FS type  
Test conditions (conforming to JIS C 5160-1)  
Item  
Category temperature range  
－25℃ to ＋70℃  
MAX operating voltage  
5.5Vdc, 11Vdc, 12Vdc  
5.5V：0.022F to 1.0F  
11V：0.47, 1.0  
Capacitance  
Refer to “Measurement Conditions”  
Refer to “Measurement Conditions”  
12V：1.0F, 5.0F  
Capacitance allowance  
ESR  
＋80％, －20％  
5.5V：0.0022F to 1.0F  
11V：0.47F, 1.0F  
12V：1.0F, 5.0F  
Measured at 1kHz, 10mA ; See also “Measurement  
Conditions”  
Current (30-minutes value)  
Refer to standard ratings  
Refer to “Measurement Conditions”  
Capacitance  
ESR  
Current (30 minutes value)  
More than 90% of initial ratings  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
Surge voltage：6.3V (5.5V type)  
：12.6V (11V type)  
：13.6V (12V type)  
Charge：30 sec.  
Discharge：9min 30sec.  
Number of cycles：1000  
Series resistance：0.022F  
：0.047F  
560Ω  
300Ω  
150Ω  
56Ω  
Surge  
：0.10F  
Appearance  
No obvious abnormality  
：0.22F  
：0.47F  
30Ω  
：1.0F  
15Ω  
10Ω  
：5.0F  
Discharge resistance：0Ω  
Temperature：70±2℃  
Capacitance  
ESR  
Capacitance  
ESR  
Capacitance  
ESR  
Current (30 minutes value)  
Capacitance  
ESR  
50% or higher than initial value  
300% or less than initial value  
Phase 2  
Phase 3  
Conforms to 4.17  
Phase1：＋25±2℃  
Phase2：－25±2℃  
Phase4：＋25±2℃  
Phase5：＋70±2℃  
Phase6：＋25±2℃  
150% or less than initial value  
Satisfy initial ratings  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Characteristics in  
different temperature  
Phase 5  
Phase 6  
Current (30 minutes value)  
Satisfy initial ratings  
Lead strength (tensile)  
Vibration resistance  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
Conforms to 4.9  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.13  
Frequency：10 to 55 Hz  
Testing time：6 hours  
Appearance  
Conforms to 4.11  
Over 3/4 of the terminal should be covered by  
the new solder  
Solder temp：245±5℃  
Solderability  
Dipping time：5±0.5 sec.  
1.6mm from the bottom should be dipped.  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.10  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
No obvious abnormality  
Solder temp：260±10℃  
Dipping time：10±1 sec.  
1.6mm from the bottom should be dipped.  
Solder heat resistance  
Appearance  
Capacitance  
ESR  
Current (30 minutes value)  
Conforms to 4.12  
Temperature condition：－25℃→Room temperature→  
＋70℃→Room temperature  
Number of cycles：5 Cycles  
Temperature cycle  
Appearance  
Over 90% of the initial value (5.5V type)  
Within ±20% of initial value (11V type, 12Vtype)  
Capacitance  
Conforms to 4.14  
High temp. and high  
humidity resistance  
Temperature：40±2℃  
Relative humidity：90 to 95％RH  
Testing time：240±8 hours  
ESR  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
No obvious abnormality  
Current (30 minutes value)  
Appearance  
Over 85% of the initial value (5.5V type)  
Within ±20% of initial value (11V type, 12Vtype)  
Below 200% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
Capacitance  
Conforms to 4.15  
Temperature：70±2℃  
ESR  
High temperature load  
Voltage applied：MAX operating voltage  
Series protection resistance：0Ω  
Current (30 minutes value)  
Appearance  
＋48  
Testing time：1000 Hours  
ꢀ0  
Super Capacitors Vol.12 29  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
6.8 FA Series, FE Series  
●FA Series  
Dimensions  
Markings on sleeve  
F
D ± 0.5  
Rated voltage  
A1  
Date  
code  
001 FA  
5 V  
FA  
FA  
5 V  
0.1 F  
0.1 F  
Nominal  
capacitance  
A1  
001 FA  
Serial  
number  
5 V  
0.1 F  
5 V  
0.1 F  
Sleeve  
Negative polarity  
identification mark  
P ± 0.5  
○－ ○＋  
d
d
1
2
± 0.1  
± 0.1  
（Terminal）  
Specifications  
MAX  
Nominal capacitance  
MAX  
Dimension (unit:mm)  
Rated  
voltage  
（Vdc）  
MAX ESR  
（at 1 kHz）  
（Ω）  
operating  
current at  
30 min.  
（mA）  
Weight  
（g）  
Part Number  
Charge  
Discharge  
voltage  
（Vdc）  
φD  
H
P
ℓ
d1  
d2  
system (F) system (F)  
FA0H473ZF  
FA0H104ZF  
FA0H224ZF  
FA0H474ZF  
FA0H105ZF  
FA1A223ZF  
FA1A104ZF  
FA1A224ZF  
FA1A474ZF  
5.5  
5
5
0.047  
0.10  
0.22  
0.47  
1.0  
0.075  
0.16  
0.35  
0.75  
1.6  
20.0  
8.0  
5.0  
3.5  
2.5  
20.0  
8.0  
6.0  
4.0  
0.071  
0.15  
0.33  
0.71  
1.5  
16.0  
21.5  
28.5  
36.5  
44.5  
16.0  
28.5  
36.5  
44.5  
15.5  
15.5  
16.5  
16.5  
18.5  
25.0  
25.5  
27.5  
28.5  
5.1  
7.6  
5.0  
5.5  
9.5  
9.5  
9.5  
5.0  
9.5  
9.5  
9.5  
0.4  
0.6  
0.6  
0.6  
1.0  
0.4  
0.6  
1.0  
1.0  
1.2  
1.2  
1.4  
1.7  
1.4  
1.2  
1.4  
1.4  
1.4  
6.2  
12  
25  
42  
65  
7.5  
32  
55  
83  
5.5  
5.5  
5
10.2  
15.0  
20.0  
5.1  
5.5  
5
5.5  
5
11.0  
11.0  
11.0  
11.0  
10  
10  
10  
10  
0.022  
0.10  
0.22  
0.47  
0.035  
0.16  
0.35  
0.75  
0.066  
0.30  
0.66  
1.41  
10.2  
15.0  
20.0  
●FE Series  
Dimensions  
Markings on sleeve  
F
D ± 0.5  
A1  
Date  
code  
MAX  
operating voltage  
001 FE 5.5 V  
0.047 F  
FE 5.5 V  
0.047 F  
Nominal  
capacitance  
Serial  
number  
Sleeve  
A1  
P ± 0.5  
○－ ○＋  
Negative polarity  
identification mark  
d
1
2
± 0.1  
± 0.1  
d
（Terminal）  
Specifications  
MAX  
Nominal capacitance  
Dimension (unit:mm)  
MAX ESR MAX current  
operating  
Weight  
（g）  
Part Number  
（at 1 kHz） at 30 min.  
Charge  
Discharge  
system (F)  
voltage  
（Vdc）  
φD  
H
P
ℓ
d1  
d2  
（Ω）  
（mA）  
system (F)  
FE0H473ZF  
FE0H104ZF  
FE0H224ZF  
FE0H474ZF  
FE0H105ZF  
FE0H155ZF  
5.5  
5.5  
5.5  
5.5  
5.5  
5.5  
0.047  
0.10  
0.22  
0.47  
1.0  
0.075  
0.16  
0.35  
0.75  
1.4  
14.0  
6.5  
3.5  
1.8  
1.0  
0.6  
0.071  
0.15  
0.33  
0.71  
1.5  
14.5  
16.5  
21.5  
28.5  
36.5  
44.5  
14.0  
14.0  
15.5  
16.5  
18.5  
18.5  
5.1  
5.1  
2.2  
2.7  
3.0  
6.1  
6.1  
6.1  
0.4  
0.4  
0.6  
0.6  
0.6  
1.0  
1.2  
1.2  
1.2  
1.4  
1.7  
1.4  
3.9  
5
7.6  
9.5  
16  
38  
72  
10.2  
15.0  
20.0  
1.5  
2.1  
2.3  
30 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
Specifications  
Series name  
Test conditions  
(conforming to JIS C 5160-1)  
FA  
FE  
Item  
Category temperature range  
－25℃ to ＋70℃  
－40℃ to ＋70℃  
MAX operating voltage  
Capacitance  
5.5Vdc, 11Vdc  
5.5Vdc  
5.5V：0.047F to 1.0F  
11V：0.022F to 0.47F  
＋80％, －20％  
0.047F to 1.5F  
Refer to “Measurement Conditions”  
Refer to “Measurement Conditions”  
Measured at 1kHz, 10mA ; See also  
“Measurement Conditions”  
Capacitance allowance  
ESR  
＋80％, －20％  
Refer to standard ratings  
Refer to standard ratings  
Refer to standard ratings  
Current (30-minutes value)  
Refer to standard ratings  
Refer to “Measurement Conditions”  
Capacitance  
ESR  
More than 90% of initial ratings  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
Surge voltage：6.3V (5.5V type)  
：12.6V (11V type)  
Charge：30 sec.  
Current (30 minutes value)  
Discharge：9min 30sec.  
Number of cycles：1000  
Series resistance ：0.047F  
：0.10F  
300Ω  
Surge  
150Ω  
56Ω  
30Ω  
15Ω  
：0.22F  
Appearance  
No obvious abnormality  
：0.47F  
：1.0F, 1.5F  
Discharge resistance：0Ω  
Temperature：70±2℃  
Capacitance  
ESR  
Capacitance  
ESR  
Capacitance  
ESR  
Current (30 minutes value)  
Capacitance  
ESR  
70% or higher than initial value  
Phase  
2
Phase  
2
300% or less than initial value  
Conforms to 4.17  
40% or higher than initial value  
400% or less than initial value  
200% or less than initial value  
Satisfy initial ratings  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Satisfy initial ratings  
Phase  
3
Phase  
3
Phase1：＋25±2℃  
Phase2：－25±2℃  
Phase3：－40±2℃ (FE type)  
Phase4：＋25±2℃  
Phase5：＋70±2℃  
Phase6：＋25±2℃  
Characteristics  
in different  
temperature  
150% or less than initial value  
Satisfy initial ratings  
1.5CV (mA) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Satisfy initial ratings  
Phase  
5
Phase  
5
Phase  
6
Phase  
6
Current (30 minutes value)  
Lead strength (tensile)  
Capacitance  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
Conforms to 4.9  
Conforms to 4.13  
Frequency：10 to 55 Hz  
Testing time：6 hours  
ESR  
Vibration  
Current (30 minutes value)  
resistance  
Appearance  
Conforms to 4.11  
Over 3/4 of the terminal should  
be covered by the new solder  
Over 3/4 of the terminal should  
be covered by the new solder  
Solder temp：245±5℃  
Solderability  
Dipping time：5±0.5 sec.  
1.6mm from the bottom should be dipped.  
Capacitance  
ESR  
Conforms to 4.10  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
Solder heat  
resistance  
Solder temp：260±10℃  
Dipping time：10±1 sec.  
1.6mm from the bottom should be dipped.  
Current (30 minutes value)  
Appearance  
Capacitance  
ESR  
Conforms to 4.12  
Temperature condition：－25℃ (－40℃ for FE type)→  
Room temperature→  
Temperature  
cycle  
Current (30 minutes value)  
＋70℃→Room temperature  
Appearance  
Capacitance  
No obvious abnormality  
Over 90% of initial value  
No obvious abnormality  
Number of cycles：5 Cycles  
Within ±20% of initial value  
Not to exceed 120% of initial  
ratings  
Not to exceed 120% of initial  
ratings  
Not to exceed 120% of initial  
ratings  
Not to exceed 120% of initial  
ratings  
Conforms to 4.14  
ESR  
High temp. and  
high humidity  
resistance  
Temperature：40±2℃  
Relative humidity：90 to 95％RH  
Testing time：240±8 hours  
Current (30 minutes value)  
Appearance  
Capacitance  
ESR  
No obvious abnormality  
Over 85% of initial value  
Below 120% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
No obvious abnormality  
Within ±30% of initial value  
Below 200% of initial ratings  
Below 200% of initial ratings  
No obvious abnormality  
Conforms to 4.15  
High  
temperature  
load  
Temperature：70±2℃  
Voltage applied：MAX operating voltage  
Current (30 minutes value)  
Appearance  
Series protection resistance：0Ω  
＋48  
Testing time：1000 Hours  
ꢀ0  
Super Capacitors Vol.12 31  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
6.9 HV Series (High capacitance Type)  
Dimensions  
Markings on sleeve  
H
L min.  
ΔL min.  
2.7V  
10F  
Negative terminal  
SuperCapacitor  
HV  
Positive terminal  
Specifications  
MAX  
operating  
voltage  
（Vdc）  
Dimension (unit:mm)  
Nominal  
MAX ESR MAX current  
Weight  
（g）  
Part Number  
capacitance （at 1 kHz） at 30 min.  
φD  
H
P
φd  
L
ΔL  
（F）  
（Ω）  
（mA）  
HVS0E106NF  
HVS0E226NF  
HVS0E506NF  
HVS0E107NF  
2.7  
2.7  
2.7  
2.7  
10  
22  
100  
100  
30  
8
10.0  
12.5  
18.0  
22.0  
35±2  
35±2  
40±5  
50±5  
5.0  
5.0  
0.6  
0.6  
0.8  
1.0  
15.0  
15.0  
15.0  
15.0  
5.0  
5.0  
5.0  
5.0  
4.5  
6.5  
18  
40  
81  
50  
7.5  
14.0  
24.0  
100  
30  
10.2  
Specifications  
Item  
Specifications  
Test conditions (conforming to JIS C 5160-2)  
－25℃ to ＋60℃ (50F, 100F),  
－25℃ to ＋70℃ (10F, 22F),  
2.7Vdc  
10F, 22F, 50F, 100F  
±30％  
Category temperature range  
MAX operating voltage  
Capacitance  
Capacitance allowance  
Refer to “Measurement Conditions”  
Refer to “Measurement Conditions”  
Measured at 1kHz, 10mA ; See also “Measurement  
Conditions”  
ESR  
Refer to standard ratings  
Current (30-minutes value)  
Refer to standard ratings  
Refer to “Measurement Conditions”  
Capacitance  
ESR  
Capacitance  
ESR  
Current (30 minutes value)  
Capacitance  
ESR  
50% higher than initial value  
400% or less than initial value  
150% or less than initial value  
Satisfy initial ratings  
Phase 2  
Phase 4  
Conforms to 4.13  
Characteristics in  
different temperature  
Phase2：Category MIN temp.  
Phase4：Category MAX temp.  
Phase5：25℃  
1.5×10－3CV (A) or below  
Within ±20% of initial value  
Satisfy initial ratings  
Phase 5  
Current (30 minutes value)  
Satisfy initial ratings  
Lead strength (tensile)  
Vibration resistance  
No terminal damage  
Satisfy initial ratings  
No obvious abnormality  
Conforms to 4.5  
Capacitance  
ESR  
Current (30 minutes value)  
Appearance  
Conforms to 4.9  
Frequency：10 to 55 Hz  
Testing time：6 hours  
Conforms to 4.7  
Over 3/4 of the terminal should be covered by  
the new solder  
Solder temp：245±5℃  
Dipping time：5±0.5 sec.  
1.6mm from the bottom should be dipped.  
Solderability  
Capacitance  
Conforms to 4.6  
ESR  
Satisfy initial ratings  
No obvious abnormality  
Satisfy initial ratings  
Solder temp：260±10℃  
Dipping time：10±1 sec.  
1.6mm from the bottom should be dipped.  
Solder heat resistance  
Current (30 minutes value)  
Appearance  
Capacitance  
Conforms to 4.8  
Temperature condition：－25℃→Room temperature→  
＋70℃ (10F, 22F), ＋60℃ (50F, 100F)→  
Room temperature  
Number of cycles：5 Cycles  
Conforms to 4.14  
Temperature：40±2℃ (50F, 100F)  
Relative humidity：90 to 95％RH  
Testing time：240±8 hours  
ESR  
Temperature cycle  
Current (30 minutes value)  
Appearance  
No obvious abnormality  
Capacitance  
ESR  
Current (30 minutes value)  
Appearance  
Within ±20% of initial value  
Not to exceed 120% of initial ratings  
Not to exceed 120% of initial ratings  
No obvious abnormality  
High temp. and high  
humidity resistance  
Capacitance  
ESR  
Current (30 minutes value)  
Within ±30% of initial value  
Below 200% of initial ratings  
Below 200% of initial ratings  
Conforms to 4.10  
Temperature：＋70℃ (10F, 22F), ＋60℃ (50F, 100F)  
Voltage applied：MAX operating voltage  
Series protection resistance：0Ω  
Testing time：1000 Hours  
High temperature load  
Appearance  
No obvious abnormality  
＋48  
ꢀ0  
32 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
7. Packing  
1. FM Series  
(1) Bulk  
•Packing method：Pack in vinyl bags then pack them into cardboard boxes.  
•Standard packing quantity：1000pcs (100pcs / vinyl bag×10)  
However：FM0H104ZF-L1 and FM0H224ZF-L1＝800pcs, FMC0H334ZF＝400pcs, FMC0H334ZF-L1＝300pcs  
(2) Taping  
•Packing method：Ammo pack  
•Standard packing quantity：1000pcs However, FMC0H334ZFTP( ) = 400pcs  
2. FC Series  
Part name  
Packing unit  
FC0H473ZFTBR24  
FC0H104ZFTBR24  
FC0H224ZFTBR24  
FC0H474ZFTBR32-SS  
FC0H105ZFTBR44-SS  
FC0V104ZFTBR24  
FC0V224ZFTBR24  
FC0V474ZFTBR24  
FCS0H473ZFTBR24  
FCS0H104ZFTBR24  
FCS0H224ZFTBR24  
FCS0V104ZFTBR24  
FCS0V224ZFTBR24  
FCS0V474ZFTBR24  
FCH0V683ZFTBR16  
FCH0H433ZFTBR16  
1000 PCS. / reel  
1000 PCS. / reel  
500 PCS. / reel  
200 PCS. / reel  
150 PCS. / reel  
1000 PCS. / reel  
1000 PCS. / reel  
500 PCS. / reel  
1000 PCS. / reel  
1000 PCS. / reel  
500 PCS. / reel  
1000 PCS. / reel  
1000 PCS. / reel  
500 PCS. / reel  
1500 PCS. / reel  
1500 PCS. / reel  
3．FG, FT, FS, FR, FY, FA Series  
(1) Bulk (Small type)  
•Packing method：Pack in vinyl bags then pack them into cardboard boxes.  
•Standard packing quantity: see chart below.  
（Unit：Pises）  
Series name  
Capacitance  
0.010F  
FA  
FS  
FY  
FYH  
－
FE  
FR  
FG  
FT  
5.5V type 11V type  
5.5V type 11V type, 12V type  
FYD  
－
FYL  
2000  
2000  
1600  
－
－
－
240  
－
－
－
－
1000  
800  
600  
400  
－
－
－
－
－
－
－
－
－
2000  
2000  
2000  
1600  
800  
－
－
0.022F  
0.047F  
0.10F  
0.22F  
0.47F  
1.0F  
－
1000  
1000  
800  
400  
240  
－
1600  
800  
600  
500  
－
800  
400  
400  
300  
240  
－
400  
－
400  
400  
－
－
－
1000  
400  
400  
－
－
－
－
－
－
－
－
300  
－
－
－
－
－
－
240  
(2) Bulk (large type)  
•Packing method: Pin the terminal onto a conductive mat; then pack it into individual cardboard box with insulation material.  
•Standard packing quantity: see chart below.  
（Unit：Pises）  
Series name  
Capacitance  
0.10F  
FA  
FS  
FY  
FYH  
－
FE  
FR  
FG  
FT  
5.5V type 11V type  
5.5V type 11V type, 12V type  
FYD  
－
FYL  
－
－
－
－
－
－
－
－
－
－
－
90  
50  
30  
20  
－
－
－
－
－
－
－
50  
30  
20  
－
－
－
－
－
－
－
－
－
90  
50  
30  
－
20  
－
－
－
－
－
－
－
90  
50  
－
－
－
－
－
－
－
－
－
50  
50  
－
－
－
－
－
20  
－
－
－
－
90  
－
－
－
－
－
－
－
－
－
－
－
－
90  
－
－
50  
30  
－
－
20  
0.22F  
0.47F  
1.0F  
1.4F  
1.5F  
2.2F  
3.3F  
4.7F  
5.0F  
5.6F  
－
－
－
90  
50  
－
－
90  
90  
－
－
－
－
160  
90  
－
50  
－
－
－
－
－
50  
－
－
－
－
－
－
4. Winded type (HV Series)  
•Packing method：Pack in vinyl bags then pack them into cardboard boxes.  
•Standard packing quantity：320pcs (10F), 224pcs (22F), 120pcs (50F), 80pcs (100F)  
Super Capacitors Vol.12 33  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
8. List of Plating Type and Sleeve Type  
By changing the solder plating from leaded solder to lead-free solder, and the outer tube material of can-cased conventional  
SuperCapacitor from polyvinyl chloride to Polyethylene Terephathatate (PET), our new SuperCapacitor has now became even  
more friendlier to the environment.  
a. Iron ＋ copper base ＋ lead-free solder plating (Sn-1Cu)  
b. SUS nickel base ＋ copper base ＋ reflow lead-free solder plating (100% Sn, reflow processed)  
c. Iron ＋ copper base ＋ lead-free solder plating (100% Sn)  
Series  
FA  
Part Number  
All FA Series  
Plating  
a
Sleeve  
PET (Blue)  
FE  
All FE Series  
a
PET (Blue)  
FS  
All FS Series  
a
PET (Blue)  
FR  
All FR Series  
a
PET (Blue)  
FT  
All FT Series  
a
PET (Blue)  
All FYD type  
a
PET (Blue)  
All FYH type  
a
PET (Blue)  
FY  
FYL0H473ZF  
a
PET (Blue)  
FYL0H223ZF  
b
PET (Blue)  
FYL0H103ZF  
b
PET (Blue)  
FG0H103ZF  
FG0H223ZF  
FG0H473ZF  
FG0H104ZF  
FG0H224ZF  
FG0H474ZF  
FG0H105ZF  
FG0H225ZF  
FG0H475ZF  
FGH0H104ZF  
FGH0H224ZF  
FGH0H474ZF  
FGH0H105ZF  
All FGR type  
All FM Series  
b
b
b
b
a
a
a
a
a
b
b
a
a
a
a
b
b
b
a
a
b
b
b
b
b
b
b
b
b
b
b
c
PET（Blue）  
PET（Blue）  
PET（Blue）  
PET（Blue）  
PET（Blue）  
PET（Blue）  
PET（Blue）  
PET（Blue）  
PET（Blue）  
PET（Blue）  
PET（Blue）  
PET（Blue）  
PET（Blue）  
PET（Blue）  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
No tube used  
PET (Blue)  
FG  
FM  
FC0H473ZFTBR24  
FC0H104ZFTBR24  
FC0H224ZFTBR24  
FC0H474ZFTBR32-SS  
FC0H105ZFTBR44-SS  
FC0V104ZFTBR24  
FC0V224ZFTBR24  
FC0V474ZFTBR24  
FCH0V683ZFTBR16  
FCH0H433ZFTBR16  
FCS0H473ZFTBR24  
FCS0H104ZFTBR24  
FCS0H224ZFTBR24  
FCS0V104ZFTBR24  
FCS0V224ZFTBR24  
FCS0V474ZFTBR24  
All HV Series  
FC  
HV  
Recommended Pb-free solder : Sn / 3.5Ag / 0.75Cu  
Sn / 3.0Ag / 0.5Cu  
Sn / 0.7Cu  
Sn / 2.5Ag / 1.0Bi / 0.5Cu  
34 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
9. Measurement Conditions  
(1) Capacitance ( Charge System )  
Capacitance is calculated from expression (9) by measuring the charge time constant ( τ ) of the capacitor (C). Prior to  
measurement, short between both pins of the capacitor for 30 minutes or more to let it discharge. In addition, follow the indication  
of the product when determining the polarity of the capacitor during charging.  
τ
RC  
EO: 3.0 (V) … Product with maximum operating voltage  
Capacitance: C =  
(F)  
(9)  
3.5 V  
5.0 (V) … Product with maximum operating voltage  
5.5 V  
6.0 (V) … Product with maximum operating voltage  
Swich  
6.5 V  
10.0 (V) … Product with maximum operating voltage  
R
C
+
–
11 V  
E
O
VC  
C
12.0 (V) … Product with maximum operating voltage  
12 V  
τ: Time from start of charging until Vc becomes  
0.632E0 (V) (sec)  
RC:See table below (Ω).  
FY  
FYH  
–
FM, FME  
FMR, FML  
FG  
FGR  
5000 Ω  
2000 Ω  
–
FC, FCH  
FCS  
FA  
–
FE  
FS  
–
FR  
–
FMC  
FGH  
FT  
FYD  
–
FYL  
5000 Ω  
0.010F  
0.022F  
0.033F  
0.043F  
0.047F  
0.068F  
0.10F  
–
–
–
–
5000 Ω  
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1000 Ω  
1000 Ω 2000 Ω 2000 Ω 2000 Ω 2000 Ω  
2000 Ω  
Discharge  
–
Discharge  
–
–
–
–
–
–
–
–
–
–
–
–
–
Discharge  
–
–
1000 Ω 1000 Ω 1000 Ω 2000 Ω 1000 Ω 2000 Ω 1000 Ω  
2000 Ω  
1000 Ω 2000 Ω  
–
–
–
–
–
–
–
–
–
–
–
Discharge  
510 Ω  
510 Ω  
510 Ω 1000 Ω 510 Ω  
1000 Ω  
1000 Ω  
1000 Ω 1000 Ω Discharge 510 Ω Discharge  
0H: Discharge  
0.22F  
200 Ω  
200 Ω  
200 Ω  
510 Ω  
510 Ω  
–
510 Ω  
–
1000 Ω Discharge 200 Ω Discharge  
0V: 1000 Ω  
0.33F  
0.47F  
1.0F  
1.4F  
1.5F  
2.2F  
3.3F  
4.7F  
5.0F  
5.6F  
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Discharge  
–
–
–
–
100 Ω  
100 Ω  
100 Ω  
200 Ω  
200 Ω  
200 Ω  
–
–
–
–
–
–
–
–
–
1000 Ω Discharge 100 Ω Discharge  
51 Ω  
51 Ω  
100 Ω  
100 Ω  
100 Ω  
100 Ω  
510 Ω Discharge 100 Ω Discharge  
–
–
–
–
–
–
–
–
51 Ω  
–
–
–
–
–
200 Ω  
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
510 Ω  
200 Ω  
–
–
–
–
–
–
–
–
–
–
51 Ω  
51 Ω  
–
–
20 Ω  
–
–
–
–
–
–
–
–
100 Ω  
–
–
–
–
–
–
–
–
–
100 Ω  
–
100 Ω  
–
–
*Capacitance values according to the constant current discharge method.  
Table 3 Capacitance measurement  
Capacitance (Discharge System)  
In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the condensor terminal  
reaches 5.5 V.  
Then, use a constant current load device and measure the time for the terminal voltage to drop from 3.0 to 2.5 V upon  
discharge at 0.22 mA for 0.22 F, for example, and calculate the static capacitance according to the equation shown below.  
Note: The current value is 1 mA discharged per 1F.  
0.22mA(I)  
SW  
5.5V  
V
1
1
: 3.0V  
: 2.5V  
A
V
1
2
V
I×(T2－T1)  
V1－V2  
V
5.5V  
C
R
V
Capactance：C＝  
(F)  
Duration (sec.)  
30 min.  
T1  
T2  
Super Capacitors Vol.12 35  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
10. Notes on Using Super Capacitor  
(Electric Double-Layer Capacitor)  
1. Circuitry design  
1.1 Useful life  
The electrical double layered capacitor (super capacitor) uses electrolyte and is sealed with rubber etc. Water in the  
electrolyte can evaporate in use over long periods at high temperatures, thus reducing electrostatic capacity which in turn will  
create greater internal resistance. The characteristics of the super capacitor can vary greatly depending on the environment  
it is used in. Therefore, controlling the usage environment will ensure prolonged life of the part.  
Basic breakdown mode is an open mode due to increased internal resistance.  
1.2 Fail rate in the field  
Based on field data, the fail rate is calculated at approx. 0.006Fit. We estimate that unreported failures are ten times this  
amount. Therefore, we assume that the fail rate is below 0.06Fit.  
1.3 Voltage application when maximum usable voltage is exceeded  
Performance may be compromised, and in some cases leakage or damage may occur if applied voltage exceeds maximum  
working voltage.  
1.4 Use of capacitor as a smoothing capacitor (ripple absorption) in electrical circuits  
As super capacitors contain a high level of internal resistance, they are not recommended for use as electrical smoothing  
capacitors in electrical circuits.  
Performance may be compromised, and in some cases leakage or damage may occur if a super capacitor is used in ripple  
absorption.  
1.5 Series connections  
As applied voltage balance to each super capacitor is lost when used in series connection, excess voltage may be applied to  
some super capacitors, which will not only negatively affect its performance but may also cause leakage and/or damage.  
Allow ample margin for maximum voltage or attach a circuit for applying equal voltage to each super capacitor (partial  
pressure resistor/voltage divider) when using super capacitors in series connection.  
Also, arrange super capacitors so that the temperature between each capacitor will not vary.  
1.6 Outer sleeve insulation  
The outer sleeve wrapped around the super capacitor indicates that it is sealed, however the outer sleeve is not guaranteed  
for insulation purposes. Therefore, it cannot be used where insulation is necessary.  
1.7 Polar characteristics  
The super capacitor is manufactured so that the terminal on the outer case is negative (-). Align the (-) symbol during use. Even  
though discharging has been carried out prior to shipping, any residual electrical charge may negatively affect other parts.  
1.8 Use next to heat emitters  
Useful life of the super capacitor will be significantly affected if used near heat emitting items (coils, power transistors, and  
posistors etc) where the super capacitor itself may become heated.  
1.9 Usage environment  
This device cannot be used in any acidic, alkaline or similar type of environment.  
36 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
1.10 Super capacitors fitted with pressure valves  
HV series super capacitors are fitted with pressure valves Make an opening in the top of the pressure valve to avoid any  
damage to the super capacitor when the pressure valve is in use. Allow at least a 2mm opening for models with a diameter  
of φ18mm or less, and at least a 3mm opening for models with a diameter of φ22mm.  
2. Mounting  
2.1 Mounting onto a reflow furnace  
Except for the FC series, it is not possible to mount this capacitor onto an IR / VPS reflow furnace. Do not immerse the  
capacitor into a soldering dip tank.  
2.2 Flow soldering conditions  
Keep solder under 260℃ and soldering time to within 10 seconds when using the flow automatic soldering method. (Except  
for the FC and HV series)  
2.3 Installation using a soldering iron  
Care must be taken to prevent the soldering iron from touching other parts when soldering. Keep the tip of the soldering iron  
under 400℃ and soldering time to within 3 seconds. Always make sure that the temperature of the tip is controlled. Internal  
capacitor resistance is likely to increase if the terminals are overheated.  
2.4 Lead terminal processing  
Do not attempt to bend or polish the capacitor terminals with sand paper etc. Soldering may not be possible if the metallic  
plating is removed from the top of the terminals.  
2.5 Cleaning, Coating, and Potting  
Except for the FM series, cleaning, coating, and potting must not be carried out. Consult us if this type of procedure is  
necessary.  
Terminals should be dried at less than the maximum operating temperature after cleaning.  
3. Storage  
3.1 Temperature and Humidity  
Make sure that the super capacitor is stored according to the following conditions: Temp.: 5～35℃ (Standard 25), Humidity:  
20～70% (Standard: 50%). Do not allow the build up of condensation through sudden temperature change.  
3.2 Environment conditions  
Make sure that there are no corrosive gasses like sulfur dioxide as penetration of the lead terminals is possible.  
Always store this item in an area with low dust and dirt levels.  
Make sure that the packaging will not be deformed through heavy loading, movement and/or knocks.  
Keep out of direct sunlight, and away from radiation, static electricity, and magnetic fields.  
3.3 Maximum storage period  
This item may be stored up to one year from the date of delivery if stored at the conditions stated above.  
This product should be safe to use even after being stored for over a 1 year period. However, depending on the storage  
conditions, we recommend that the soldering is checked.  
4. Dismantling  
There is a small amount of electrolyte stored within thecapacitor. Do not attempt to dismantle as direct skin contact with the  
electrolyte will cause burning.  
This product should be treated as industrial waste and not is not to be disposed of by fire.  
Super Capacitors Vol.12 37  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
38 Super Capacitors Vol.12  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  
When using our products, the following precautions should  
be taken.  
(1) Safety designing of an apparatus or a system allowing for failures of electronic components used  
in the system  
In general, failures will occur in electronic components at a certain probability. NEC TOKIN  
makes every effort to improve the quality and reliability of electronic component products.  
However, it is impossible to completely eliminate the probability of failures. Therefore, when  
using NEC TOKIN’s electronic component products, systems should be carefully designed to  
ensure redundancy in the event of an accident which would result in injury or death, fire, or social  
damage, to ensure the prevention of the spread of fire, and the prevention of faulty operation.  
(Please refer to pre-cautions to be taken when using SuperCapacitor capacitors for the details of  
failures.)  
(2) Quality level of various kinds of parts, and equipment in which the parts can be utilized  
Electronic components have a standard quality level unless otherwise specified.  
NEC TOKIN classifies the level of quality of electronic component products into three levels, in  
order from a lower level, a standard quality level, a special quality level, and a custom quality level  
in which a customer individually specifies a quality assurance program. Each of the quality levels  
has recommended applications.  
If a user wants to use the electronic parts having a standard quality level in applications other than  
the applications specified for the standard quality level, they should always consult a member of  
our company’s sales staff before using the electronic parts.  
Standard quality level:  
Computers, office automation equipment, communications equipment,  
measuring instruments, AV equipment, household electrical appli-  
ances, machine tools, personal equipment, industrial robots  
Special quality level:  
Transportation equipment (automobiles, railways, shipping, or the  
like), traffic signals, disaster prevention/crime prevention systems,  
safety devices, and medical equipment which is not directly intended  
for life-support purposes  
Custom quality level:  
Equipment for airplanes, aerospace equipment, nuclear power control  
systems, and medical equipment, apparatus or systems for life-sup-  
port purposes  
Unless otherwise shown, the quality level of NEC TOKIN’s electronic component products included  
in documents such as catalogues, data sheets or data books is the standard quality level.  
(3) This manual is subject to change without notice.  
The contents of this manual are based on data which is correct as of July 2010, and they may be  
changed without notice. If our products are used for mass-production design, please cousult with  
a member of our company’s sales staff by way of precaution.  
(4) Reprinting and copying of this manual without prior written permission from NEC TOKIN Corpo-  
ration are not permitted.  
(5) Industrial property problems  
In the event any problems associated with industrial property of a third party arising as a result of  
the use of our products, NEC TOKIN assumes no responsibility for problems other than problems  
directly associated with the constitution and manufacturing method of the products.  
(6) Should any of these products come under the category of strategic goods or services (according  
to Japan's foreign trade and foreign exchange regulations), the sender must obtain an export  
license from the Japanese Government befor said products can be exported outside Japan.  
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.  
●Please request for a specification sheet for detailed product data prior to the purchase.  
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.  
2010.11.8 9565S C A VOL12E  

相关型号：

SI9130DB

 5- and 3.3-V Step-Down Synchronous Converters

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1-E3

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135_11

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9136_11

 Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130CG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130LG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130_11

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137DB

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137LG

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9122E

 500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification Drivers

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明