NXS0104UM [NEXPERIA]
Dual supply translating transceiver; open drain; auto direction sensingProduction;型号: | NXS0104UM |
厂家: | Nexperia |
描述: | Dual supply translating transceiver; open drain; auto direction sensingProduction |
文件: | 总23页 (文件大小:329K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NXS0104
Dual supply translating transceiver; open drain;
auto direction sensing
Rev. 4 — 30 June 2021
Product data sheet
1. General description
The NXS0104 is a 4-bit, dual supply translating transceiver with auto direction sensing, that
enables bidirectional voltage level translation. It features two 4-bit input-output ports (An and Bn),
one output enable input (OE) and two supply pins (VCC(A) and VCC(B)). VCC(A) can be supplied at
any voltage between 1.65 V and 3.6 V and VCC(B) can be supplied at any voltage between 2.3 V
and 5.5 V, making the device suitable for translating between any of the voltage nodes (1.8 V,
2.5 V, 3.3 V and 5.0 V). Pins An and OE are referenced to VCC(A) and pins Bn are referenced to
VCC(B). A LOW level at pin OE causes the outputs to assume a high-impedance OFF-state. This
device is fully specified for partial power-down applications using IOFF. The IOFF circuitry disables
the output, preventing the damaging backflow current through the device when it is powered down.
2. Features and benefits
•
Wide supply voltage range:
VCC(A): 1.65 V to 3.6 V and VCC(B): 2.3 V to 5.5 V
Maximum data rates:
Push-pull: 24 Mbps
•
•
•
•
•
•
IOFF circuitry provides partial Power-down mode operation
Inputs accept voltages up to 5.5 V
ESD protection:
•
•
•
•
HBM: ANSI/ESDA/Jedec JS-001 Class 2 exceeds 2.5 kV for A port
HBM: ANSI/ESDA/Jedec JS-001 Class 3B exceeds 15 kV for B port
CDM: ANSI/ESDA/Jedec JS-002 Class C3 exceeds 1.5 kV
IEC61000-4-2 contact discharge exceeds 8000 V for B port
•
•
•
Latch-up performance exceeds 100 mA per JESD 78B Class II
Multiple package options
Specified from -40 °C to +85 °C and -40 °C to +125 °C
3. Applications
•
•
•
•
Desktop PC
Handset
Smartphone
Tablet
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
4. Ordering information
Table 1. Ordering information
Type number
Package
Temperature range Name
Description
Version
NXS0104PW
NXS0104BQ
-40 °C to +125 °C
TSSOP14
plastic thin shrink small outline package; 14 leads;
body width 4.4 mm
SOT402-1
-40 °C to +125 °C
DHVQFN14 plastic dual in-line compatible thermal enhanced
very thin quad flat package; no leads; 14 terminals;
body 2.5 × 3 × 0.85 mm
SOT762-1
NXS0104GU12 -40 °C to +125 °C
XQFN12
plastic, extremely thin quad flat package; no leads;
12 terminals; body 1.70 × 2.0 × 0.50 mm
SOT1174-1
SOT8019-1
NXS0104UM
-40 °C to +125 °C
WLCSP12
wafer level chip-scale package; 12 bumps;
1.36 × 1.86 × 0.60 mm
5. Marking
Table 2. Marking
Type number
Marking code
NXS0104
S0104
NXS0104PW
NXS0104BQ
NXS0104GU12
NXS0104UM
m4
m4
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
2 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
6. Functional diagram
V
V
CC(B)
CC(A)
OE
T1
T1
T1
T1
T2
T2
T2
T2
ONE
SHOT
ONE
SHOT
10 kΩ
10 kΩ
10 kΩ
10 kΩ
10 kΩ
10 kΩ
10 kΩ
GATE BIAS
T3
A1
B1
B2
B3
B4
ONE
SHOT
ONE
SHOT
GATE BIAS
T3
A2
A3
A4
ONE
SHOT
ONE
SHOT
GATE BIAS
T3
ONE
SHOT
ONE
SHOT
10 kΩ
GATE BIAS
T3
aaa-029696
Fig. 1. Logic symbol
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
3 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
7. Pinning information
7.1. Pinning
NXS0104
terminal 1
index area
2
3
4
5
6
13
12
11
10
9
A1
B1
B2
B3
B4
n.c.
A2
A3
NXS0104
A4
(1)
GND
n.c.
1
2
3
4
5
6
7
14
13
12
11
10
9
V
V
CC(B)
CC(A)
A1
B1
A2
A3
B2
B3
B4
n.c.
OE
aaa-029698
Transparent top view
A4
(1) This is not a ground pin. There is no electrical or
mechanical requirement to solder the pad. In case
soldered, the solder land should remain floating or
connected to GND.
n.c.
GND
8
aaa-029697
Fig. 2. Pin configuration SOT402-1 (TSSOP14)
Fig. 3. Pin configuration SOT762-1 (DHVQFN14)
NXS0104
terminal 1
index area
V
1
2
3
4
5
11
V
CC(A)
CC(B)
A1
10 B1
A2
A3
A4
9
8
7
B2
B3
B4
aaa-029699
Transparent top view
Fig. 4. Pin configuration SOT1174-1 (XQFN12)
NXS0104
NXS0104
bump A1
index area
1
2
3
1
2
3
A
B
C
D
A
B
C
D
B1
V
V
A1
CC(B)
B2
B3
B4
A2
A3
CC(A)
OE
GND
A4
aaa-032891
aaa-032892
Transparent top view
Transparent top view
Fig. 5. Bump configuration SOT8019-1 (WLCSP12)
Fig. 6. Bump mapping for SOT8019-1 (WLCSP12)
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
4 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
7.2. Pin description
Table 3. Pin description
Symbol
Pin
Description
SOT402-1, SOT762-1 SOT1174-1
VCC(A)
1
1
supply voltage A
A1, A2, A3, A4
n.c.
2, 3, 4, 5
2, 3, 4, 5
data input or output (referenced to VCC(A)
)
6, 9
-
not connected
GND
7
6
ground (0 V)
OE
8
12
output enable input (active HIGH; referenced to VCC(A))
B4, B3, B2, B1
VCC(B)
10, 11, 12, 13
14
7, 8, 9, 10
11
data input or output (referenced to VCC(B)
)
supply voltage B
Table 4. Bump description for SOT8019-1 (WLCSP12)
Symbol
VCC(A)
Bump
Description
B2
supply voltage A
A1, A2, A3, A4
GND
A3, B3, C3, D3
data input or output (referenced to VCC(A)
)
D2
ground (0 V)
OE
C2
output enable input (active HIGH; referenced to VCC(A)
)
B1, B2, B3, B4
VCC(B)
A1, B1, C1, D1
A2
data input or output (referenced to VCC(B)
)
supply voltage B
8. Functional description
Table 5. Function table
H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state.
Supply voltage
VCC(A) [1]
Input
OE
L
Input/output
VCC(B)
An
Bn
1.65 V to 3.6 V
1.65 V to 3.6 V
GND[2]
2.3 V to 5.5 V
2.3 V to 5.5 V
GND[2]
Z
Z
H
input or output
Z
output or input
Z
X
[1] VCC(A) must be less than or equal to VCC(B) and VCC(A) must not exceed 3.6 V.
[2] When either VCC(A) or VCC(B) is at GND level, the device goes into power-down mode.
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
5 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
9. Limiting values
Table 6. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min
-0.5
-0.5
-0.5
-0.5
Max
+6.5
+6.5
+6.5
+6.5
Unit
V
VCC(A) supply voltage A
VCC(B) supply voltage B
V
VI
input voltage
A port and OE input
B port
[1]
[1]
V
V
VO
output voltage
Active mode
A or B port
[1] [2]
-0.5
VCCO + 0.5 V
Power-down or 3-state mode
A port
[1]
-0.5
-0.5
-50
-50
-
+4.6
+6.5
-
V
B port
V
IIK
input clamping current
output clamping current
output current
VI < 0 V
mA
mA
mA
mA
mA
°C
IOK
IO
VO < 0 V
-
VO = 0 V to VCCO
ICC(A) or ICC(B)
[2]
±50
100
-
ICC
IGND
Tstg
Ptot
supply current
-
ground current
-100
-65
storage temperature
total power dissipation
+150
Tamb = -40 °C to +125 °C
SOT402-1 (TSSOP14)
SOT762-1 (DHVQFN14)
[3]
[4]
-
-
500
250
mW
mW
SOT1174-1 (XQFN12)
SOT8019-1 (WLCSP12)
[1] The minimum input and minimum output voltage ratings may be exceeded if the input and output current ratings are observed.
[2] VCCO is the supply voltage associated with the output.
[3] For SOT402-1 (TSSOP14) package: Ptot derates linearly with 7.3 mW/K above 81 °C.
For SOT762-1 (DHVQFN14) package: Ptot derates linearly with 9.6 mW/K above 98 °C.
[4] For SOT8019-1 (WLCSP12) package: Ptot derates linearly with 7.3 mW/K above 116 °C.
10. Recommended operating conditions
Table 7. Recommended operating conditions [1] [2]
Symbol Parameter
Conditions
Min
1.65
2.3
Max
3.6
Unit
V
VCC(A) supply voltage A
VCC(B) supply voltage B
5.5
V
Tamb
ambient temperature
-40
+125
°C
Δt/ΔV
input transition rise and fall rate
A or B port; push-pull driving
VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
-
-
10
10
ns/V
ns/V
OE input
VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
[1] The A and B sides of an unused I/O pair must be held in the same state, both at VCCI or both at GND.
[2] VCC(A) must be less than or equal to VCC(B) and VCC(A) must not exceed 3.6 V.
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
6 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
11. Static characteristics
Table 8. Typical static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); Tamb = 25 °C.[1]
Symbol Parameter
Conditions
Min
Typ
Max Unit
II
input leakage
current
OE input;
-
-
±1
μA
VCC(A) = 1.65 V to 3.6 V; VCC(B) = 2.3 V to 5.5 V
IOZ
IOFF
OFF-state output A or B port; OE = 0 V;
-
-
±1
μA
current
VCC(A) = 1.65 V to 3.6 V; VCC(B) = 2.3 V to 5.5 V
power-off leakage A port; VCC(A) = 0 V; VCC(B) = 0 V to 5.5 V
-
-
-
-
-
±1
±1
-
μA
μA
pF
current
B port; VCC(B) = 0 V; VCC(A) = 0 V to 3.6 V
CI
input capacitance OE input; VCC(A) = 3.3 V; VCC(B) = 3.3 V
2
CI/O
input/output
capacitance
A port; VCC(A) = 3.3 V; VCC(B) = 3.3 V
enabled
-
-
10
4
-
-
pF
pF
disabled
B port; VCC(A) = 3.3 V; VCC(B) = 3.3 V
enabled
disabled
-
-
10
7
-
-
pF
pF
[1] VCC(A) must be less than or equal to VCC(B) and VCC(A) must not exceed 3.6 V.
Table 9. Typical supply current
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); Tamb = 25 °C.
VCC(A)
VCC(B)
2.5 V
ICC(A)
0.1
Unit
3.3 V
ICC(A)
0.1
5.0 V
ICC(A)
0.1
ICC(B)
0.5
0.1
-
ICC(B)
1.5
ICC(B)
4.6
1.8 V
2.5 V
3.3 V
μA
μA
μA
0.1
0.1
0.8
0.1
3.8
-
0.1
0.1
0.1
2.8
Table 10. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).[1]
Symbol Parameter Conditions -40 °C to +85 °C
-40 °C to +125 °C
Unit
Min
Max
Min
Max
VIH
HIGH-level input A port
voltage
VCC(A) = 1.65 V to 1.95 V;
VCC(A) - 0.2
VCC(A) - 0.4
VCC(A)
VCC(A)
VCC(A) - 0.2
VCC(A) - 0.4
VCC(A)
VCC(A)
V
V
VCC(B) = 2.3 V to 5.5 V
VCC(A) = 2.3 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
B port
VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
VCC(B) - 0.4
VCC(B)
VCC(B) - 0.4
VCC(B)
V
V
OE input
VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
0.65VCC(A)
VCC(A)
0.65VCC(A)
VCC(A)
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
7 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
Symbol Parameter
Conditions
-40 °C to +85 °C
-40 °C to +125 °C
Unit
Min
Max
Min
Max
VIL
LOW-level input A or B port
voltage
VCC(A) = 1.65 V to 3.6 V;
0
0.15
0
0.15
V
V
V
V
VCC(B) = 2.3 V to 5.5 V
OE input
VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
0
0.35VCC(A)
0
0.35VCC(A)
VOH
HIGH-level
A port; IO = -20 μA; VI ≥ VCC(B) - 0.4 V
output voltage
VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
0.67VCC(A)
0.67VCC(B)
-
-
0.67VCC(A)
0.67VCC(B)
-
-
B port; IO = -20 μA; VI ≥ VCC(A) - 0.2 V
VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
VOL
LOW-level
A or B port; IO = 1 mA; VI ≤ 0.15 V
output voltage
VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
-
-
-
-
-
0.4
±2
±2
±2
±2
-
-
-
-
-
0.4
±12
±12
±12
±12
V
II
input leakage
current
OE input; VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
μA
μA
μA
μA
IOZ
IOFF
OFF-state
output current
A or B port; VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
power-off
A port; VCC(A) = 0 V;
leakage current VCC(B) = 0 V to 5.5 V
B port; VCC(B) = 0 V;
VCC(A) = 0 V to 3.6 V
ICC
supply current
OE = 0 V or VCC(A); An, Bn open
ICC(A)
VCC(A) = 1.65 V to 3.6 V;
-
2.4
-
15
μA
VCC(B) = 2.3 V to 5.5 V
VCC(A) = 3.6 V; VCC(B) = 0 V
VCC(A) = 0 V; VCC(B) = 5.5 V
-
-
2.2
-1
-
-
15
-8
μA
μA
ICC(B)
VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
-
12
-
30
μA
VCC(A) = 3.6 V; VCC(B) = 0 V
VCC(A) = 0 V; VCC(B) = 5.5 V
-
-
-1
1
-
-
-5
6
μA
μA
ICC(A) + ICC(B)
VCC(A) = 1.65 V to 3.6 V;
VCC(B) = 2.3 V to 5.5 V
-
14.4
-
45
μA
[1] VCC(A) must be less than or equal to VCC(B) and VCC(A) must not exceed 3.6 V.
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
8 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
12. Dynamic characteristics
Table 11. Dynamic characteristics for temperature range -40 °C to +85 °C
Voltages are referenced to GND (ground = 0 V); for test circuit see Fig. 10; for waveforms see Fig. 7 to Fig. 9.
Symbol Parameter
Conditions
VCC(B)
Unit
2.5 V ± 0.2 V
3.3 V ± 0.3 V
5.0 V ± 0.5 V
Min
Max
Min
Max
Min
Max
VCC(A) = 1.8 V ± 0.15 V
tPHL
tPLH
tPHL
tPLH
HIGH to LOW
propagation delay
A to B
-
-
-
-
4.6
7.1
4.4
5.3
-
-
-
-
4.7
6.8
4.5
4.5
-
-
-
-
5.8 ns
7.0 ns
4.7 ns
0.5 ns
200 ns
LOW to HIGH
propagation delay
A to B
HIGH to LOW
propagation delay
B to A
LOW to HIGH
propagation delay
B to A
ten
enable time
disable time
OE to A, B
[1]
-
-
200
35
-
-
200
35
-
-
tdis
OE to A, B; no external load [1] [2]
35
ns
OE to A
OE to B
A port
-
140
125
9.5
-
140
175
9.3
9.1
-
145 ns
125 ns
7.6 ns
7.6 ns
-
-
-
tTLH
LOW to HIGH
output transition
time
3.2
3.3
2.3
2.7
1.8
2.7
B port
10.8
tTHL
HIGH to LOW
output transition
time
A port
B port
2.0
2.9
5.9
7.6
1.9
2.8
6.0
7.5
1.7
2.8
13.3 ns
10.0 ns
tsk(o)
tW
output skew time between channels
[3]
-
41
-
0.7
-
-
41
-
0.7
-
-
41
-
0.7 ns
pulse width
data rate
data inputs
-
ns
fdata
24
24
24
Mbps
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
9 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
Symbol Parameter
Conditions
VCC(B)
Unit
2.5 V ± 0.2 V
3.3 V ± 0.3 V
5.0 V ± 0.5 V
Min
Max
Min
Max
Min
Max
VCC(A) = 2.5 V ± 0.2 V
tPHL
tPLH
tPHL
tPLH
HIGH to LOW
propagation delay
A to B
-
-
-
-
3.2
3.5
3.0
2.5
-
-
-
-
3.3
4.4
3.6
1.6
-
-
-
-
3.4 ns
4.6 ns
4.3 ns
0.7 ns
200 ns
LOW to HIGH
propagation delay
A to B
HIGH to LOW
propagation delay
B to A
LOW to HIGH
propagation delay
B to A
ten
enable time
disable time
OE to A, B
[1]
-
-
200
35
-
-
200
35
-
-
tdis
OE to A, B; no external load [1] [2]
35
ns
OE to A
OE to B
A port
-
105
125
7.5
8.5
-
105
175
6.6
7.3
-
105 ns
120 ns
6.5 ns
6.3 ns
-
-
-
tTLH
LOW to HIGH
output transition
time
2.8
3.2
2.6
2.9
1.8
2.4
B port
tTHL
HIGH to LOW
output transition
time
A port
B port
1.9
2.2
5.7
7.8
1.9
2.4
5.5
6.7
1.8
2.6
5.3 ns
6.6 ns
tsk(o)
tW
output skew time between channels
[3]
-
41
-
0.7
-
-
41
-
0.7
-
-
41
-
0.7 ns
pulse width
data rate
data inputs
-
ns
fdata
24
24
24
Mbps
VCC(A) = 3.3 V ± 0.3 V
tPHL
tPLH
tPHL
tPLH
HIGH to LOW
propagation delay
A to B
-
-
-
-
-
-
-
-
-
-
-
-
2.4
4.2
2.5
2.5
-
-
-
-
3.1 ns
4.4 ns
3.3 ns
2.6 ns
200 ns
LOW to HIGH
propagation delay
A to B
HIGH to LOW
propagation delay
B to A
LOW to HIGH
propagation delay
B to A
ten
enable time
disable time
OE to A, B
[1]
-
-
-
-
-
-
-
-
-
-
-
-
-
-
200
35
-
-
tdis
OE to A, B; no external load [1] [2]
35
ns
OE to A
OE to B
A port
-
150
170
6.2
6.9
-
150 ns
120 ns
6.3 ns
7.4 ns
-
-
tTLH
LOW to HIGH
output transition
time
2.3
2.5
1.9
2.1
B port
tTHL
HIGH to LOW
output transition
time
A port
B port
-
-
-
-
2.0
2.3
5.4
7.4
1.9
2.4
5.0 ns
7.6 ns
tsk(o)
tW
output skew time between channels
[3]
-
-
-
-
-
-
-
41
-
0.7
-
-
41
-
0.7 ns
pulse width
data rate
data inputs
-
ns
fdata
24
24
Mbps
[1] ten is the same as tPZL and tPZH; tdis is the same as tPLZ and tPHZ
.
[2] These values are guaranteed by design.
[3] Skew between any two outputs of the same package switching in the same direction.
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
10 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
Table 12. Dynamic characteristics for temperature range -40 °C to +125 °C
Voltages are referenced to GND (ground = 0 V); for test circuit see Fig. 10; for waveforms see Fig. 7 to Fig. 9.
Symbol Parameter
Conditions
VCC(B)
Unit
2.5 V ± 0.2 V
3.3 V ± 0.3 V
5.0 V ± 0.5 V
Min
Max
Min
Max
Min
Max
VCC(A) = 1.8 V ± 0.15 V
tPHL
tPLH
tPHL
tPLH
HIGH to LOW
propagation delay
A to B
-
-
-
-
5.8
8.5
5.5
6.7
-
-
-
-
5.9
8.5
5.7
5.7
-
-
-
-
7.3 ns
8.8 ns
5.9 ns
0.7 ns
200 ns
LOW to HIGH
propagation delay
A to B
HIGH to LOW
propagation delay
B to A
LOW to HIGH
propagation delay
B to A
ten
enable time
disable time
OE to A, B
[1]
-
-
200
45
-
-
200
45
-
-
tdis
OE to A, B; no external load [1] [2]
45
ns
OE to A
OE to B
A port
-
140
125
11.9
13.5
-
140
175
11.7
11.4
-
145 ns
125 ns
9.5 ns
9.5 ns
-
-
-
tTLH
LOW to HIGH
output transition
time
3.2
3.3
2.3
2.7
1.8
2.7
B port
tTHL
HIGH to LOW
output transition
time
A port
B port
2.0
2.9
7.4
9.5
1.9
2.8
7.5
9.4
1.7
2.8
16.7 ns
12.5 ns
tsk(o)
tW
output skew time between channels
[3]
-
50
-
0.8
-
-
41
-
0.8
-
-
41
-
0.8 ns
pulse width
data rate
data inputs
-
ns
fdata
20
24
24
Mbps
VCC(A) = 2.5 V ± 0.2 V
tPHL
tPLH
tPHL
tPLH
HIGH to LOW
propagation delay
A to B
-
-
-
-
4.0
4.4
3.8
3.2
-
-
-
-
4.2
5.2
4.5
2.0
-
-
-
-
4.3 ns
5.5 ns
5.4 ns
0.9 ns
200 ns
LOW to HIGH
propagation delay
A to B
HIGH to LOW
propagation delay
B to A
LOW to HIGH
propagation delay
B to A
ten
enable time
disable time
OE to A, B
[1]
-
-
200
45
-
-
200
45
-
-
tdis
OE to A, B; no external load [1] [2]
45
ns
OE to A
OE to B
A port
-
105
125
9.3
-
105
175
8.3
9.7
-
105 ns
120 ns
7.8 ns
8.3 ns
-
-
-
tTLH
LOW to HIGH
output transition
time
2.8
3.2
2.6
2.9
1.8
2.4
B port
10.4
tTHL
HIGH to LOW
output transition
time
A port
B port
1.9
2.2
7.2
9.8
1.9
2.4
6.9
8.4
1.8
2.6
6.7 ns
8.3 ns
tsk(o)
tW
output skew time between channels
[3]
-
50
-
0.8
-
-
41
-
0.8
-
-
41
-
0.8 ns
pulse width
data rate
data inputs
-
ns
fdata
20
24
24
Mbps
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
11 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
Symbol Parameter
Conditions
VCC(B)
Unit
2.5 V ± 0.2 V
3.3 V ± 0.3 V
5.0 V ± 0.5 V
Min
Max
Min
Max
Min
Max
VCC(A) = 3.3 V ± 0.3 V
tPHL
tPLH
tPHL
tPLH
HIGH to LOW
propagation delay
A to B
-
-
-
-
-
-
-
-
-
-
-
-
3.0
5.3
3.2
3.2
-
-
-
-
3.9 ns
5.5 ns
4.2 ns
3.3 ns
200 ns
LOW to HIGH
propagation delay
A to B
HIGH to LOW
propagation delay
B to A
LOW to HIGH
propagation delay
B to A
ten
enable time
disable time
OE to A, B
[1]
-
-
-
-
-
-
-
-
-
-
-
-
-
-
200
45
-
-
tdis
OE to A, B; no external load [1] [2]
45
ns
OE to A
OE to B
A port
-
150
170
7.0
8.0
-
150 ns
120 ns
7.4 ns
9.3 ns
-
-
tTLH
LOW to HIGH
output transition
time
2.3
2.5
1.9
2.1
B port
tTHL
HIGH to LOW
output transition
time
A port
B port
-
-
-
-
2.0
2.3
6.8
9.3
1.9
2.4
6.3 ns
9.5 ns
tsk(o)
tW
output skew time between channels
[3]
-
-
-
-
-
-
-
41
-
0.8
-
-
41
-
0.8 ns
pulse width
data rate
data inputs
-
ns
fdata
24
24
Mbps
[1] ten is the same as tPZL and tPZH; tdis is the same as tPLZ and tPHZ
.
[2] These values are guaranteed by design.
[3] Skew between any two outputs of the same package switching in the same direction.
12.1. Waveforms and test circuit
V
I
An, Bn
input
V
M
GND
t
t
PHL
PLH
V
OH
90 %
Bn, An
output
V
M
10 %
V
OL
t
t
THL
TLH
001aal918
Measurement points are given in Table 13.
VOL and VOH are typical output voltage levels that occur with the output load.
Fig. 7. The data input (An, Bn) to data output (Bn, An) propagation delay times
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
12 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
V
I
V
OE input
M
GND
t
PLZ
V
CCO
output
LOW-to-OFF
V
X
V
OL
t
PHZ
V
OH
V
Y
output
HIGH-to-OFF
GND
outputs
enabled
outputs
disabled
aaa-029700
Measurement points are given in Table 13.
VOL and VOH are typical output voltage levels that occur with the output load.
VCCO is the supply voltage associated with the output.
Fig. 8. Disable times
V
I
OE input
GND
V
M
V
I
An, Bn
input
V
V
M
M
GND
(1)
t
en
V
CCO
An, Bn
output
V
M
V
OL
aaa-029701
(1) The enable time (ten) indicates the amount of time the user must allow for one one-shot circuitry to become
operational after OE is taken HIGH. See also Section 13.6
Measurement points are given in Table 13.
VOL is a typical output voltage level that occur with the output load.
VCCO is the supply voltage associated with the output.
Fig. 9. Enable times
Table 13. Measurement points
Supply voltage
VCCO
Input
Output
VM [2]
VM [1]
VX
VY
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
5.0 V ± 0.5 V
0.5VCCI
0.5VCCI
0.5VCCI
0.5VCCI
0.5VCCO
0.5VCCO
0.5VCCO
0.5VCCO
VOL + 0.15 V
VOL + 0.15 V
VOL + 0.3 V
VOL + 0.3 V
VOH - 0.15 V
VOH - 0.15 V
VOH - 0.3 V
VOH - 0.3 V
[1] VCCI is the supply voltage associated with the input.
[2] VCCO is the supply voltage associated with the output.
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
13 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
t
W
V
I
90 %
negative
pulse
V
V
M
M
10 %
0 V
t
t
r
f
t
t
r
f
V
I
90 %
positive
pulse
V
V
M
M
10 %
0 V
t
W
V
EXT
V
V
CC(B)
CC(A)
R
L
V
V
O
I
G
DUT
C
R
L
L
aaa-029721
Test data is given in Table 14.
All input pulses are supplied by generators having the following characteristics:
PRR ≤ 10 MHz; ZO = 50 Ω; dV/dt ≥ 1.0 V/ns.
RL = Load resistance.
CL = Load capacitance including jig and probe capacitance.
VEXT = External voltage for measuring switching times.
Fig. 10. Test circuit for measuring switching times
Table 14. Test data
Supply voltage
VCC(A)
Input
Load
CL
VEXT
VCC(B)
VI [1] Δt/ΔV
RL [2]
tPLH, tPHL tPZH, tPHZ tPZL, tPLZ [3]
1.65 V to 3.6 V 2.3 V to 5.5 V VCCI
≤ 1.0 ns/V
15 pF
50 kΩ, 1 MΩ open
open
2VCCO
[1] VCCI is the supply voltage associated with the input.
[2] For measuring data rate, pulse width, propagation delay and output rise and fall measurements, RL = 1 MΩ.
For measuring enable and disable times, RL = 50 kΩ.
[3] VCCO is the supply voltage associated with the output.
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
14 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
13. Application information
13.1. Applications
Voltage level-translation applications. The NXS0104 can be used in point-to-point applications to
interface between devices or systems operating at different supply voltages. The device is primarily
targeted at I2C or 1-wire which use open-drain drivers, it may also be used in applications where
push-pull drivers are connected to the ports, however the NXB0104 may be more suitable.
1.8 V
3.3 V
1 µF
V
CC(A)
V
CC(B)
0.1 µF
0.1 µF
OE
1.8 V
SYSTEM
CONTROLLER
3.3 V
SYSTEM
NXS0104
A1
A2
A3
A4
B1
B2
B3
B4
DATA
DATA
GND
aaa-029702
Fig. 11. Typical operating circuit
13.2. Architecture
The architecture of the NXS0104 is shown in Fig. 12. The device does not require an extra input
signal to control the direction of data flow from A to B or B to A.
V
V
CC(B)
CC(A)
T1
T2
ONE
ONE
SHOT
SHOT
10 kΩ
10 kΩ
GATE BIAS
T3
A
B
001aal965
Fig. 12. Architecture of NXS0104 I/O cell (one channel)
The NXS0104 is a "switch" type voltage translator, it employs two key circuits to enable voltage
translation:
1. A pass-gate transistor (N-channel) that ties the ports together.
2. An output edge-rate accelerator that detects and accelerates rising edges on the I/O pins.
The gate bias voltage of the pass gate transistor (T3) is set at approximately one threshold voltage
above the VCC level of the low-voltage side. During a LOW-to-HIGH transition the output one-shot
accelerates the output transition by switching on the PMOS transistors (T1, T2) bypassing the
10 kΩ pull-up resistors and increasing current drive capability. The one-shot is activated once
the input transition reaches approximately 0.5VCCI; it is de-activated approximately 50 ns after
the output reaches 0.5VCCO. During the acceleration time the driver output resistance is between
approximately 50 Ω and 70 Ω.
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
15 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
To avoid signal contention and minimize dynamic ICC, the user should wait for the one-shot circuit
to turn-off before applying a signal in the opposite direction. Pull-up resistors are included in the
device for DC current sourcing capability.
13.3. Input driver requirements
As the NXS0104 is a switch type translator, properties of the input driver directly effect the output
signal. The external open-drain or push-pull driver applied to an I/O determines the static current
sinking capability of the system; the max data rate, HIGH-to-LOW output transition time (tTHL) and
propagation delay (tPHL) are dependent upon the output impedance and edge-rate of the external
driver. The limits provided for these parameters in the datasheet assume a driver with output
impedance below 50 Ω is used.
13.4. Output load considerations
The maximum lumped capacitive load that can be driven is dependant upon the one-shot pulse
duration. In cases with very heavy capacitive loading there is a risk that the output will not reach
the positive rail within the one-shot pulse duration.To avoid excessive capacitive loading and to
ensure correct triggering of the one-shot it's recommended to use short trace lengths and low
capacitance connectors on NXS0104 PCB layouts. To ensure low impedance termination and
avoid output signal oscillations and one-shot re-triggering, the length of the PCB trace should be
such that the round trip delay of any reflection is within the one-shot pulse duration.
13.5. Power up
During operation VCC(A) must never be higher than VCC(B), however during power-up
VCC(A) ≥ VCC(B) does not damage the device, so any power supply can be ramped up first. There is
no special power-up sequencing required. The NXS0104 includes circuitry that disables all output
ports when either VCC(A) or VCC(B) is switched off.
13.6. Enable and disable
An output enable input (OE) is used to disable the device. Setting OE to LOW causes all I/Os
to assume the high-impedance OFF-state. The disable time (tdis with no external load) indicates
the delay between when OE goes LOW and when outputs actually become disabled. The enable
time (ten) indicates the amount of time the user must allow for one one-shot circuitry to become
operational after OE is taken HIGH. To ensure the high-impedance OFF-state during power-up or
power-down, pin OE should be tied to GND through a pull-down resistor, the minimum value of the
resistor is determined by the current-sourcing capability of the driver.
13.7. Pull-up or pull-down resistors on I/O lines
Each A port I/O has an internal 10 kΩ pull-up resistor to VCC(A), and each B port I/O has an internal
10 kΩ pull-up resistor to VCC(B). If a smaller value of pull-up resistor is required, an external resistor
must be added parallel to the internal 10 kΩ, this will effect the VOL level. When OE goes LOW the
internal pull-ups of the NXS0104 are disabled.
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
16 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
14. Package outline
TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm
SOT402-1
D
E
A
X
c
y
H
v
M
A
E
Z
8
14
Q
(A )
3
A
2
A
A
1
pin 1 index
θ
L
p
L
1
7
detail X
w
M
b
p
e
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
A
(1)
(2)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
Q
v
w
y
Z
θ
1
2
3
p
E
p
max.
8o
0o
0.15
0.05
0.95
0.80
0.30
0.19
0.2
0.1
5.1
4.9
4.5
4.3
6.6
6.2
0.75
0.50
0.4
0.3
0.72
0.38
mm
1.1
0.65
1
0.2
0.13
0.1
0.25
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
99-12-27
03-02-18
SOT402-1
MO-153
Fig. 13. Package outline SOT402-1 (TSSOP14)
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
17 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
DHVQFN14: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads;
14 terminals; body 2.5 x 3 x 0.85 mm
SOT762-1
B
A
E
D
A
A
1
c
detail X
terminal 1
index area
C
terminal 1
index area
e
1
v
w
C
C
A B
y
y
C
1
e
b
2
6
L
1
7
8
E
h
e
14
k
13
9
D
h
X
k
0
2
4 mm
w
scale
Dimensions (mm are the original dimensions)
(1) (1)
(1)
Unit
A
A
b
c
D
D
h
E
E
e
e
k
L
v
y
y
1
1
h
1
max
nom
min
1
0.05 0.30
0.02 0.25 0.2 3.0 1.50 2.5 1.00 0.5
0.00 0.18 2.9 1.35 2.4 0.85
3.1 1.65 2.6 1.15
0.5
0.4 0.1 0.05 0.05 0.1
0.2 0.3
mm
2
Note
sot762-1_po
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
References
Outline
version
European
projection
Issue date
IEC
JEDEC
JEITA
15-04-10
15-05-05
SOT762-1
MO-241
Fig. 14. Package outline SOT762-1 (DHVQFN14)
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
18 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
XQFN12: plastic, extremely thin quad flat package; no leads;
12 terminals; body 1.70 x 2.00 x 0.50 mm
SOT1174-1
X
B
A
E
D
terminal 1
index area
A
A
1
A
3
detail X
C
B
A
∅ v
∅ w
C
C
b
y
1
y
C
5
1
7
e
1
e
11
terminal 1
index area
L
1
L
0
1
2 mm
scale
Dimensions
(1)
Unit
A
A
A
b
D
E
e
e
1
L
L
1
v
w
y
y
1
1
3
max 0.5 0.05
mm nom
min
0.25 1.8 2.1
0.127 0.20 1.7 2.0
0.15 1.6 1.9
0.55
0.4
1.6 0.50 0.15 0.1 0.05 0.05 0.05
0.45
0.00
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
sot1174-1_po
References
Outline
version
European
projection
Issue date
IEC
- - -
JEDEC
MO-288
JEITA
- - -
10-04-07
10-04-21
SOT1174-1
Fig. 15. Package outline SOT1174-1 (XQFN12)
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
19 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
WLCSP12: wafer level chip-scale package, 12 bumps; 1.36 x 1.86 x 0.60 mm
SOT8019-1
s
C
(2×)
E
A
B
y
1
C
bump A1
index area
A
2
A
D
y
C
(12×)
A
1
detail X
s
C
B
(2×)
C
e
e
Ø v
A
b
C
(12×)
D
C
B
A
e
e
e
1/2 e
1
2
3
bump A1
index area
X
0
2 mm
scale
s
Dimensions (mm are the original dimensions)
Unit
A
A
A
b
D
E
e
v
y
y
1
1
2
max 0.6325 0.183 0.4495 0.245
nom
min 0.5675 0.143 0.4245 0.205
mm
0.6000 0.163 0.4370 0.225 1.86 1.36 0.5 0.025 0.05 0.05 0.10
sot8019-1_po
Issue date
References
Outline
version
European
projection
IEC
JEDEC
JEITA
20-08-11
20-08-12
SOT8019-1
Fig. 16. Package outline SOT8019-1 (WLCSP12)
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
20 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
15. Abbreviations
Table 15. Abbreviations
Acronym
Description
CDM
DUT
ESD
HBM
I2C
Charged Device Model
Device Under Test
ElectroStatic Discharge
Human Body Model
Inter-Integrated Circuit
Printed Circuit Board
Pulse Rate Repetition
PCB
PRR
16. Revision history
Table 16. Revision history
Document ID
Release date Data sheet status
20210630 Product data sheet
Type number NXS0104UM (SOT8019-1 / WLCSP12) added.
Change notice Supersedes
NXS0104 v.4
Modifications:
- NXS0104 v.3
•
NXS0104 v.3
Modifications:
20201113
Table 11 and Table 12: Disable times updated..
20200827 Product data sheet
Product data sheet
-
NXS0104 v.2
•
NXS0104 v.2
Modifications:
-
NXS0104 v.1
•
•
Table 6: Derating values for Ptot total power dissipation updated.
Table 11 and Table 12: Footnotes corrected.
NXS0104 v.1
20190228
Product data sheet
-
-
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
21 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
injury, death or severe property or environmental damage. Nexperia and its
suppliers accept no liability for inclusion and/or use of Nexperia products in
such equipment or applications and therefore such inclusion and/or use is at
the customer’s own risk.
17. Legal information
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Data sheet status
Document status Product
Definition
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. Nexperia makes no representation
or warranty that such applications will be suitable for the specified use
[1][2]
status [3]
Objective [short]
data sheet
Development
This document contains data from
the objective specification for
product development.
without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using Nexperia products, and Nexperia accepts no liability for
any assistance with applications or customer product design. It is customer’s
sole responsibility to determine whether the Nexperia product is suitable
and fit for the customer’s applications and products planned, as well as
for the planned application and use of customer’s third party customer(s).
Customers should provide appropriate design and operating safeguards to
minimize the risks associated with their applications and products.
Preliminary [short]
data sheet
Qualification
Production
This document contains data from
the preliminary specification.
Product [short]
data sheet
This document contains the product
specification.
[1] Please consult the most recently issued document before initiating or
completing a design.
Nexperia does not accept any liability related to any default, damage, costs
or problem which is based on any weakness or default in the customer’s
applications or products, or the application or use by customer’s third party
customer(s). Customer is responsible for doing all necessary testing for the
customer’s applications and products using Nexperia products in order to
avoid a default of the applications and the products or of the application or
use by customer’s third party customer(s). Nexperia does not accept any
liability in this respect.
[2] The term 'short data sheet' is explained in section "Definitions".
[3] The product status of device(s) described in this document may have
changed since this document was published and may differ in case of
multiple devices. The latest product status information is available on
the internet at https://www.nexperia.com.
Definitions
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those
given in the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. Nexperia does not give any representations or
warranties as to the accuracy or completeness of information included herein
and shall have no liability for the consequences of use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is
intended for quick reference only and should not be relied upon to contain
detailed and full information. For detailed and full information see the relevant
full data sheet, which is available on request via the local Nexperia sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Terms and conditions of commercial sale — Nexperia products are
sold subject to the general terms and conditions of commercial sale, as
published at http://www.nexperia.com/profile/terms, unless otherwise agreed
in a valid written individual agreement. In case an individual agreement is
concluded only the terms and conditions of the respective agreement shall
apply. Nexperia hereby expressly objects to applying the customer’s general
terms and conditions with regard to the purchase of Nexperia products by
customer.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
Nexperia and its customer, unless Nexperia and customer have explicitly
agreed otherwise in writing. In no event however, shall an agreement be
valid in which the Nexperia product is deemed to offer functions and qualities
beyond those described in the Product data sheet.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Disclaimers
Limited warranty and liability — Information in this document is believed
to be accurate and reliable. However, Nexperia does not give any
representations or warranties, expressed or implied, as to the accuracy
or completeness of such information and shall have no liability for the
consequences of use of such information. Nexperia takes no responsibility
for the content in this document if provided by an information source outside
of Nexperia.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific Nexperia product is automotive qualified, the
product is not suitable for automotive use. It is neither qualified nor tested in
accordance with automotive testing or application requirements. Nexperia
accepts no liability for inclusion and/or use of non-automotive qualified
products in automotive equipment or applications.
In no event shall Nexperia be liable for any indirect, incidental, punitive,
special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal
or replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards,
customer (a) shall use the product without Nexperia’s warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
Nexperia’s specifications such use shall be solely at customer’s own risk,
and (c) customer fully indemnifies Nexperia for any liability, damages or failed
product claims resulting from customer design and use of the product for
automotive applications beyond Nexperia’s standard warranty and Nexperia’s
product specifications.
Notwithstanding any damages that customer might incur for any reason
whatsoever, Nexperia’s aggregate and cumulative liability towards customer
for the products described herein shall be limited in accordance with the
Terms and conditions of commercial sale of Nexperia.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
Right to make changes — Nexperia reserves the right to make changes
to information published in this document, including without limitation
specifications and product descriptions, at any time and without notice. This
document supersedes and replaces all information supplied prior to the
publication hereof.
Trademarks
Suitability for use — Nexperia products are not designed, authorized or
warranted to be suitable for use in life support, life-critical or safety-critical
systems or equipment, nor in applications where failure or malfunction
of an Nexperia product can reasonably be expected to result in personal
Notice: All referenced brands, product names, service names and
trademarks are the property of their respective owners.
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
22 / 23
Nexperia
NXS0104
Dual supply translating transceiver; open drain; auto direction sensing
Contents
1. General description......................................................1
2. Features and benefits.................................................. 1
3. Applications.................................................................. 1
4. Ordering information....................................................2
5. Marking..........................................................................2
6. Functional diagram.......................................................3
7. Pinning information......................................................4
7.1. Pinning.........................................................................4
7.2. Pin description.............................................................5
8. Functional description................................................. 5
9. Limiting values............................................................. 6
10. Recommended operating conditions........................6
11. Static characteristics..................................................7
12. Dynamic characteristics............................................ 9
12.1. Waveforms and test circuit...................................... 12
13. Application information........................................... 15
13.1. Applications..............................................................15
13.2. Architecture..............................................................15
13.3. Input driver requirements.........................................16
13.4. Output load considerations......................................16
13.5. Power up................................................................. 16
13.6. Enable and disable..................................................16
13.7. Pull-up or pull-down resistors on I/O lines............... 16
14. Package outline........................................................ 17
15. Abbreviations............................................................21
16. Revision history........................................................21
17. Legal information......................................................22
© Nexperia B.V. 2021. All rights reserved
For more information, please visit: http://www.nexperia.com
For sales office addresses, please send an email to: salesaddresses@nexperia.com
Date of release: 30 June 2021
©
NXS0104
All information provided in this document is subject to legal disclaimers.
Nexperia B.V. 2021. All rights reserved
Product data sheet
Rev. 4 — 30 June 2021
23 / 23
相关型号:
NXS0108BQ
Dual supply translating transceiver; open drain; auto direction sensingProduction
NEXPERIA
NXS0108BQ-Q100
Dual supply translating transceiver; open drain; auto direction sensingProduction
NEXPERIA
NXS0108PW
Dual supply translating transceiver; open drain; auto direction sensingProduction
NEXPERIA
NXS0108PW-Q100
Dual supply translating transceiver; open drain; auto direction sensingProduction
NEXPERIA
NXS0506UP
SD 3.0-compatible memory card integrated auto-direction control and level translator with EMI filter and ESD protectionProduction
NEXPERIA
©2020 ICPDF网 联系我们和版权申明