PLF0G681MDO1TD [NICHICON]

Aluminum Electrolytic Capacitor, Polarized, Aluminum (solid Polymer), 4V, 20% +Tol, 20% -Tol, 680uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT;


型号：	PLF0G681MDO1TD
厂家：	NICHICON CORPORATION
描述：	Aluminum Electrolytic Capacitor, Polarized, Aluminum (solid Polymer), 4V, 20% +Tol, 20% -Tol, 680uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT 电容器固定电容器
文件：	总2页 (文件大小：104K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

Radial Lead Type, Standard

LF series

Ultra Low ESR, High ripple current.

Load life of 2000 hours at 105°C.

Radial lead type :

Lead free flow soldering condition correspondence.

Adapted to the RoHS directive (2002/95/EC).

Specifications

Item

Performance Characteristics

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

–55 ~ +105°C

2.5 ~ 16V

270 ~ 1000µF

±20% at 120Hz, 20°C

Not more than value of Standard ratings 120Hz, 20°C

tan

(

Not more than value of Standard ratings 100kHz, 20°C

ESR

Leakage Current ( 2)

Not more than value of Standard ratings. After 2 minute's application of rated voltage. 20°C

Characteristics of Temperature

Impedance Ratio

Z+105°C / Z+20°C

Z–55°C / Z+20°C

1.25

(100kHz)

Capacitance change

(

)

Within ± 20% of initial value

After 2000 hours' application of rated voltage

at 105°C, capacitors meet the specified value

for life characteristics listed at right.

tan δ

150% or less of the initial specified value

Initial specified value or less

Endurance

Damp Heat

(

ESR

Leakage current ( 2)

Capacitance change

(

)

Within ± 20% of initial value

After 1000 hours' application of rated voltage

at 60°C 90%RH, capacitors meet the specified value

for life characteristics listed at right.

tan δ

150% or less of the initial specified value

Initial specified value or less

(

ESR

Leakage current ( 2)

To comply with recommended conditions for

reflow soldering. Pre-heating shall be done

at 150 ~ 200°C and for 60 ~ 180 sec.

Peak temp. is 265°C, within 10 sec.

Measurement for solder temperature profile shall

be made at a point on the terminal nearest where

the terminals protrude through the soldering side

of PC board.

Capacitance change

Within ± 10% of initial value ( 3)

130% or less of the initial specified value

Initial specified value or less

tan δ

Resistance to

Soldering Heat

(

ESR

Leakage current ( 2)

Marking

Navy blue print on the case top

1 ESR measurements should be made at a point on the terminal nearest the end seal of the capacitor.

2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the

temperature of 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

Type numbering system (Example : 4V 560 F)

Dimensions

Taping code

(mm)

Size

φD

φd

φ8 × 9L φ8 × 12L φ10 × 13L

8.0

8.5

3.5

0.6

8.0

11.5

3.5

10.0

12.5

5.0

0.6

Voltage

2.5

6.3

Code

Please refer to page 21 about the end seal configulation.

Dimension table in next page.

CAT.8100V

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

LF series

Standard ratings

(

)

ESR (mΩ)

Rated ripple

(mArms)

Rated Voltage

Rated Capacitance

(µF)

Case Size

φD×L (mm)

Leakage Current

(0.2CV)(µA)

tan δ

Part Number

(

)

code

(at 100kHz 20˚C)

560

680

820

1000

560

680

820

470

680

270

470

270

470

0.08

280

340

410

500

448

544

656

592

857

540

940

864

1504

4800

5700

5200

6200

6500

5200

5500

6200

6500

5200

5500

6300

4900

5700

4800

5000

PLF0E561MCO1

PLF0E681MDO1

PLF0E821MCO6

PLF0E821MDO1

PLF0E102MDO1

PLF0G561MCO6

PLF0G561MDO1

PLF0G681MDO1

PLF0G821MDO1

PLF0J471MCO6

PLF0J471MDO1

PLF0J681MDO1

PLF1A271MDO1

PLF1A471MDO1

PLF1C271MDO1

PLF1C471MDO1

8 × 9

8 × 12

8 × 9

2.5

(0E)

8 × 12

10 × 13

8 × 9

8 × 12

10 × 13

8 × 9

(0G)

6.3

(0J)

8 × 12

10 × 13

8 × 12

10 × 13

8 × 12

10 × 13

(1A)

(1C)

No marked,

will be put at 12th digit of type numbering system.

Rated Ripple (mArms) at 105°C 100kHz

: In this case,

will be put at 12th digit of type numbering system.

Taping specifications are given in page 24.

Please refer to page 3 for the minimum order quantity.

CAT.8100V

相关型号：