LM3641M [NSC]
Lithium-Ion Battery Pack Protection Circuit; 锂离子电池保护电路型号: | LM3641M |
厂家: | National Semiconductor |
描述: | Lithium-Ion Battery Pack Protection Circuit |
文件: | 总17页 (文件大小:331K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
January 1999
LM3641
Lithium-Ion Battery Pack Protection Circuit
General Description
Features
n Automatic battery disconnect when the cell is
over-charged or over-discharged.
The LM3641 Lithium Protection Integrated Circuit resides in-
side a 3.6V Lithium-Ion battery pack consisting of a single
cell or multiple parallel cells. The IC controls the ON/OFF
state of a pair of low threshold N-channel power MOSFETs
placed in series with the battery cell(s). The purpose of this
MOSFET pair is to protect the cell(s) from inadvertent elec-
trical over-stress. The IC compares the cell voltage against
internally programmed minimum and maximum limits. Tran-
sient voltage faults of approximately 1.25 seconds are toler-
ated.
n Maximum cell voltage for MOSFET conduction is factory
programmable between 4.0V and 4.4V with a 25 mV
tolerance (0˚C to +60˚C).
n Minimum cell voltage for MOSFET conduction =
±
±
0.57•VMAX 3.5% (0˚C to +60˚C).
±
n Internal 4 mΩ current sense resistor provides 0.5A
maximum accuracy for detection of overcurrent faults.
The maximum charge and discharge current is factory
programmable between 1A and 5A. A single overcurrent
fault event opens and protects the MOSFET pair.
n Automatic detection of safe pack conditions for recovery
(MOSFET pair ON) from a fault condition (over/under
discharged or overcurrent).
The IC also monitors the bi-directional current flow in the bat-
tery pack by measuring the voltage across a robust 4 mΩ
current sensing resistor internal to the protection IC pack-
age. The IC turns OFF the MOSFET pair whenever any fault
limit is exceeded. Momentary current surges 4 ms are tol-
erated.
<
n Average current drain = 1.2 µA typical.
The Enable pin allows external ON/OFF control of the MOS-
FET pair and resets the IC after the MOSFET pair is turned
OFF and the pack is safe to operate again.
n Optional Enable pack terminal can be used to prevent
accidental short circuit of pack and for maximizing the
shelf life of the pack (IC powers down when the pack is
not in use).
n Over-current events cause connection of an internal
50 kΩ “FET-Bypass” resistance across OFF MOSFET
The limits for overcharge and overdischarge voltage, as well
as independent limits for each direction of overcurrent are
factory adjusted employing EEPROM.
>
pair. Loads 3–7 MΩ are required for return to
conduction mode.
n Over-charged states cause connection of a 5 kΩ
“Cell-Bypass” resistor to ensure that the cell is not
allowed to be overcharged by leakage paths.
Typical Application
DS012931-1
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
© 1999 National Semiconductor Corporation
DS012931
www.national.com
Connection Diagram and Ordering Information
Top View
8-Lead SOIC (M08A)
DS012931-2
Actual Size
DS012931-3
Order Number LM3641M
See NS Package Number M08A
This device is factory programmable. Contact your local NSC sales office for ordering information.
www.national.com
2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
ESD Susceptibility
2 kV
Human Body Model (Note 3)
Lead Temperature
(Soldering, 10s)
260˚C
Maximum Input Supply Voltage
Operating Range (Note 1)
(VDD
)
−0.3V to 5.5V
V+ or GATE or Full Pin Voltage
Enable or V− Pin Current
Power Dissipation (Note 2)
−0.3V to VDD + 0.3V
Ambient Temperature Range
Junction Temperature Range
0˚C to +60˚C
−40˚C to +125˚C
±
200 µA
Internally limited
LM3641
Electrical Characteristics
Specifications with standard type face for TJ = 25˚C, and those with bold type apply over full Operating Temperature Range.
Unless otherwise specified, VSS = 0V, VDD = 3.6V, VENABLE = VDD
.
Symbol
Parameter
Conditions
Typical
(Note 4)
Limit
(Note 5)
Units
VMAX
Overcharge Protection
Accuracy
0˚C to +60˚C
A.S.(Note 6)
V
±
25
mV(max)
<
@
VMAX-85
Overcharge Protection
Accuracy
Temp = 85˚C
VMAX 25˚C
VMAX-RANGE
Overcharge Protection
Program Range
4.2
V
4.0
4.4
V(max)
V(min)
V
VSAFE
VMIN
Max Cell Voltage Overshoot
VMAX + 100 mV
0.57•VMAX
(referred to VMAX
)
Overdischarge Protection
Accuracy
V
V(max)
V(min)
V
+0.04 • VMAX
−0.04 • VMAX
VGATE-FETS-ON
IGATE-FETS-ON
Gate Pin High
1 MΩ Load
VDD −50 mV
2
Gate Pin FET Turn-on
Impedence
kΩ
IGATE-FETS-OFF
IMAX-CHG
Gate Pin OFF Current
VGate = 0V
10
nA
A
Overcurrent Protection
Accuracy — Charging
A.S.(Note 6)
+0.5
−0.5
A(max)
A(min)
IMAX-DIS
Overcurrent Protection
Accuracy — Disharging
A.S.(Note 6)
A
+0.5
−0.5
A(max)
A(min)
ISUPPLY
Supply Current (VDD, V+,
control pins) (Note 7)
normal mode
120
1
µApeak
µA rms
=
VDD 3.6V
excludes IR2
4
µA rms(max)
IENABLE PIN
IV+
Enable Pin Current (sink)
VENABLE = VDD
400
40
1
nA
nA rms
s
Cell Sense Pin Current (sink) VDD = 3.6V
<
V+ VMAX
tSAMPLE
Cell Voltage Sampling
Period — Normal and
Overdischarge Modes
0.75
1.5
s(min)
s(max)
s
>
tSAMPLE-OVERCHARGED
Cell Voltage Sampling
Period — Overcharged
V+ VMAX
0.25
4
0.19
0.28
s(min)
s(max)
NSAMPLE
Number of consecutive
samples for overcharge or
overdischarge prior to
disconnect
3
www.national.com
LM3641
Electrical Characteristics (Continued)
Specifications with standard type face for TJ = 25˚C, and those with bold type apply over full Operating Temperature Range.
Unless otherwise specified, VSS = 0V, VDD = 3.6V, VENABLE = VDD
.
Symbol
Parameter
Conditions
Typical
(Note 4)
Limit
(Note 5)
Units
tOVERCHARGE
Overcharge Transient
1.6
s
Rejection Time (Note 8)
0.57
2.64
s(min)
s(max)
s
tOVERDISCHARGE
Overdischarge Transient
Rejection Time (Note 8)
4
3
6
s(min)
s(max)
ms
tOVERCURRENT
DC
Overcurrent Transient
Rejection Time
6
<
Duty Cycle of Pulse Charging VMAX VCELL
87.5
%
<
VSAFE
>
VCELL VSAFE
50
%
→
→
tENABLE-DELAY
Delay from Rising/Falling
Enable pin to FETs ON/OFF
(Note 9)
L
H
H
L
5
3
ms
±
VRECOVERY
MOSFET Threshold Voltage
36
mV
V
VMIN-CHARGE
Minimum Cell Voltage that
0
can be charged, VGATE
VDD (Note 10)
≈
>
VFULL-HIGH
Maximum High Output
Voltage of Full Pin
V+ VMAX
VDD − 1.2V
10
<
IFULL 4 µA
<
IFULL-OFF
Source/Sink Current of Full
Pin in TRI-STATE®
V+ VMAX
nA
VFULL = 0V
<
IR-SENSE
RSENSE
Maximum RSENSE Current
RSENSE Range
Duration 6 ms
60
4
A
mΩ
Note 1: Absolute Maximum ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is in-
tended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see Electrical Characteristics. The guar-
anteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2: The maximum allowable power dissipation is calculated by using P
= (T
JMAX
− T )/θ , where T = 150˚C, T is the ambient temperature, and θ
JA JMAX A JA
DMAX
A
= 160˚C/W.
Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin.
Note 4: Typical numbers are at 25˚C and represent the most likely parametric norm.
Note 5: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate National’s Averaging Outgoing Quality Level (AOQL).
Note 6: Application Specific. This analog parameter’s value is programmed during National’s production testing of the device. Please contact your local NSC sales
office to specify the V
between 1A and 5A. I can be programmed between 1A and 5A.
, I
MAX-DIS
includes V pin peak currents that occur at each t
and I
values when ordering this device. V
can be programmed between 4.0V and 4.4V. I
MAX-CHG
can be programmed
MAX MAX-CHG
MAX-DIS
MAX
Note 7:
I
period. The I peak current duration is approximately 2.2 ms and the I
DD VDD
peak current
SUPPLY
is approximately 120 µA.
DD
sample
Note 8: Computed from 4 sample periods of the worst case values of t
SAMPLE
and t .
SAMPLE-OVERCHARGED
<
<
Note 9: High pulses 3 ms (typ) will be typically ignored and low pulses 5 ms (typ) will be typically ignored.
Note 10: will be limited by the threshold of M3.
V
MIN-CHARGE
www.national.com
4
Typical Performance Characteristics
Maximum Current and Normalized
Maximum Voltage vs. Temperature
GATE Pin and MOSFET GATE
Voltage vs CELL Voltage
DS012931-4
DS012931-5
Supply Current
Supply Current vs Time
DS012931-7
DS012931-6
Pin* Current vs
Pin* Voltage
Supply and Enable Current
vs Enable Voltage
DS012931-8
DS012931-9
5
www.national.com
Block Diagram
DS012931-10
Test Circuit
DS012931-11
www.national.com
6
OVERCURRENT PROTECTION
Product Description
The battery current is monitored continuously by measuring
the voltage across the internal sense resistor. If the terminal
current exceeds IMAX-CHG (programmable) in the charge
mode for longer than tOVERCURRENT, the MOSFET pair dis-
connects. Similarly, if the terminal current exceeds IMAX-DIS
(programmable) in the discharge mode for longer than
Normal charging of Li-Ion packs requires Constant Voltage
Constant Current (CVCC) chargers that terminate charging
at a voltage value just below the maximum protection volt-
age (VMAX). Only in the event of an invalid charger or an out
of compliance charger operation should the protection IC ter-
minate charging.
t
OVERCURRENT, the MOSFET pair disconnects. Recovery to
conduction mode requires either 1) a momentary detach-
ment of the pack so the Enable pin can be cycled low, then
high or 2) a direct low to high signal to the Enable pin con-
trolled from logic.
OVERCHARGE PROTECTION
The IC protects the cell(s) against overcharge. Normally, the
cell voltage is sampled once a second. Four consecutive
>
samples of VCELL VMAX result in the MOSFET pair turning
OFF. The transient response for overvoltage requires one
sample at the tSAMPLE period (1s typical) and three tSAMPLE-
OVERVOLTAGE periods (0.25s typical). The first overcharge
event is asynchronous to the 1 second sampling so the delay
between the actual instance of overcharge and the first
ENABLE PIN
The pack can be protected from accidental short circuits
should the Enable pin be made available as a third battery
pack terminal. This third pack terminal is tied to the pack’s
positive terminal through a connection on either a valid
charger or load. Shorting the high impedance Enable pin to
the pack’s positive terminal enables all functions of the pro-
tection circuit. The Enable pin disables the MOSFET pair
whenever this pin is floating, such as when the battery pack
is detached from a valid load or charger. Floating the Enable
pin also forces the protection circuit into FET’s OFF mode to
maximize the shelf life of the battery pack. When the Enable
pin is used to recover from overcharge, overdischarge or
overcurrent events, the voltage measurement system
memory is cleared of previous results. If the MOSFET by-
pass resistor is active, and the Enable goes low, the bypass
resistor turns OFF. A series resistor of 470 kΩ to 1 MΩ be-
tween the Enablel terminal of the pack and the Enable pin of
the IC, protects the IC from ESD events at the pack’s termi-
nals.
sample can result anywhere in the range of zero to tSAMPLE
.
>
The requirement for 4 consecutive samples of VCELL VMAX
filters noise from the cell due to transient currents. Should
the cell voltage exceed VMAX by more than 100 mV (VSAFE),
the MOSFETs will turn off on the first sample reading. This
provides an extra measure of safety. The return to conduc-
tion mode requires that a load be applied to the pack or
<
→
VCELL VMAX − 20 mV. Also a L H signal on the Enable pin
>
will reset the GATE high, but if VCELL VMAX, the GATE will
go low again after 1.75 seconds. Whenever an overcharge
disconnect has occurred, a cell bypass resistor (≈5 kΩ) is
switched across the VDD and VSS pins and the Full pin pulls
to near VDD. The cell bypass resistor ensures that the cell is
discharged even though some component of R1’s current
will still flow in the cell, if a charger is applied. The cell by-
<
pass resistor is removed when VCELL VMAX again.
SLEEPMODE
ACTIVE RECTIFICATION
Sleepmode is a reduced current state that occurs when the
Enable pin is floating or low. The FETs are turned OFF.
Sleepmode minimizes the artificial self-discharge of the pack
when the pack is not in use.
Overcharged cells can be discharged by the application of a
load to the pack. Active Rectification is the biasing of the
power MOSFETs GATE so that the VDS = VRECOVERY for dis-
charge currents. The MOSFETs turn OFF for charge cur-
rents. The Active Rectification amplifier assures uninter-
rupted conduction for discharge currents only. The Full pin’s
INVALID CHARGER
Assume a charger that exceeds the VMAX rating of the IC is
applied to the pack. The power MOSFETs will eventually turn
>
output impedance is ≈80 kΩ when active high (VCELL
<
VMAX) and TRI-STATE when inactive (VCELL
VMAX). The
<
OFF due to overcharge if ICHARGER IMAX-CHG, or turn OFF
Full pin can optionally supply a small FET current necessary
to stabilize the Active Rectification loop by maintaining at
least (VDD−1V)/R6+80k)•ID in the MOSFET. The Full pin’s
overcharge signal could be used in applications where the
due to overcurrent if the invalid charger’s current exceeds
I
MAX-CHG. If the charger was applied to the pack with the po-
larity reversed, then the MOSFETs would eventually turn
OFF due to either overdischarge or overcurrent depending
on the magnitude of the charger’s available current. In either
case, the voltage on the V− pin will be driven by the open cir-
cuit voltage of the charger. The V− pin is clamped by internal
diodes to VDD and VSS and the pin’s current limited by R1
(see the typical curve “Pin Current vs. Pin Voltage”) with R1
= 100k, the pin current will not exceed the maximum recom-
charger is logically disabled by the protection circuit,
a
change time-out circuit is initiated or whenever an over-
charge signal is otherwise desired. The Full signal will go low
(TRI-STATE with an external resistor pulldown) and cell by-
<
pass turns off if a cell decays to VCELL VMAX
.
OVERDISCHARGE PROTECTION
±
±
mended value of 200 µA for a 20V invalid charger. Higher
invalid charger voltages can be tolerated when using higher
values for R1. Proper LCCE operation is not limited, even by
values for R1 in excess of 1 MΩ.
The cell(s) are also protected against overdischarge. Four
<
consecutive 1 Hz samples of VCELL
VMIN result in the
MOSFET pair turning OFF. Cells that have discharged below
VMIN due to long periods of self-discharge can still be
charged. Return to conduction mode for overdischarged
packs automatically occurs if a charger is applied to the
→
pack. Also a L H signal on the Enable pin will reset the
<
GATE high, however if VCELL
OFF again in 4 seconds.
VMIN, the GATE will turn
7
www.national.com
OFF, the MOSFET pair remain OFF (4). This example exag-
gerates the rate of these events. The actual operation would
result in many ON/OFF cycles at a decreasing duty cycle
prior to complete termination of charge.
Product Description (Continued)
NORMAL TERMINATION OF CHARGING
As you can see in Figure 1, the cell voltage must exceed
VMAX for 4 consecutive samples before the MOSFET pair is
turned OFF (1). Once VMAX is exceeded, the sampling rate
increases to 4 Hz. The sampling rate will return to 1 Hz only
LOAD APPLIED IN OVERCHARGED STATE
If a load is momentarily applied while the cell is in over-
charged state, then the MOSFET pair is momentarily turned
ON, see Figure 4. The MOSFET pair will stay ON only as
long as the load is applied. The MOSFET pair will stay ON
after the load is removed only if the cell voltage remains be-
low VMAX for 4 consecutive samples. Possible events are
shown as examples of operation:
<
after 4 consecutive samples result in VCELL
VMAX. After
the MOSFET pair is OFF (2), the voltage across the cell(s)
relax and the cell voltage will drop below VMAX. On the next
sample, (3), the MOSFET pair will turn ON. As long as the
charger is applied and the MOSFET pair turn ON, the cell
voltage will exceed VMAX again. The cycle of 4 samples ON
a 1 samples OFF will continue until the cell voltage equals
(1) A momentary load is applied to an overcharged cell, the
MOSFET pair stay ON only as long as the load is applied.
The gate drive is limited so that the MOSFET pair ON volt-
age will match a bias voltage generated internal to the IC,
V
MAX after the MOSFET pair is OFF, (4). This example exag-
gerates the rate of these events. The actual operation would
result in many ON/OFF cycles at a decreasing duty cycle
prior to complete termination of charge. The cell bypass re-
sistor will discharge the cell enough to turn on the GATE over
a period of minutes.
V
RECOVERY. This bias voltage is the minimum MOSFET ON
voltage that allows for the detection of a load. This mode of
operation is Active Rectification. Note that the MOSFET pair
do not turn ON for the momentary application of a charger.
NORMAL TERMINATION OF DISCHARGING
(2) A load is applied for less than 4 samples. The MOSFET
pair is ON for the load period, but turn OFF after the load is
The cell voltage must go below VMIN for 4 consecutive
samples before the MOSFET pair is turned OFF (1), which is
shown in Figure 2. Once the MOSFET pair is OFF and the
current is interrupted, the voltage across the cell(s) will in-
crease and the cell voltage could exceed VMIN (2). The
MOSFET pair remain off until a charger is applied to the
pack (3). The presence of a charger turns the MOSFET pair
ON. Deeply discharged cells will be charged, although for
some narrow bands of VCELL, the GATE may occasionally
pulse OFF momentarily.
<
removed. Only after the 4th sample of VCELL VMAX will the
MOSFET pair turn ON, this time will full drive potential.
(3) Assume the application of a charger. Conduction is al-
lowed because the FETs are ON, but the MOSFET pair will
stay ON only for 4 consecutive overcharge samples. See the
diagram for the “Normal Termination of Charging”.
(4) The MOSFET pair will turn OFF after the 4 consecutive
overcharge samples.
<
(5) A load is applied and after VCELL VMAX for 4 consecu-
TERMINATION OF ILLEGALLY HIGH CHARGING
tive samples, the MOSFET pair turn ON full. As long as
VCELL stays below VMAX, the MOSFET pair will stay ON.
Should a high charge current be applied to the pack near the
end of charge, the cell voltage could exceed VSAFE, which is
approximately 100 mV greater than VMAX (1), see Figure 3.
On the first detection of a cell voltage in excess of VSAFE-
OVERCHARGE, the MOSFET pair will be turned OFF (2). The
sample rate increases to 4 Hz after the first detection of
Should a load be applied that exceeds the overcurrent-
discharge current limit while the IC is in active rectification
mode, the MOSFET pair will turn OFF. Recovery requires
that either the IC detects a load greater than 3–7 MΩ or that
the cell voltage remains under VMAX for 4 samples. If the
load that caused overcurrent remains after the cell voltage
drops under VMAX for 4 samples, then the MOSFET pair will
turn ON once more and normal overcurrent mode is entered.
>
VCELL VMAX. It is desirable under these circumstances for
the MOSFET pair to turn ON for only the shortest allowed
time period, which is 0.25 seconds. Each sample exceeding
V
SAFE causes the MOSFET pair to turn OFF (3). Should the
cell voltage not drop below VMAX after the MOSFET pair turn
DS012931-12
FIGURE 1. Normal Termination of Charging
www.national.com
8
Product Description (Continued)
DS012931-13
FIGURE 2. Normal Termination of Discharging
DS012931-14
FIGURE 3. Termination of Illegally High Charging
DS012931-15
FIGURE 4. Load Applied in Overcharged State
•
The maximum cell voltage limit is trimmed by EEPROM
and offers optimal accuracy. Each EEPROM cell has re-
dundant EEPROM transistors for additional reliability.
The EEPROM register also contains a parity check bit. In
the rare event that an EEPROM bit would change state,
the power MOSFETs will be turned OFF rather than allow
the IC to operate out of specification.
Fail Safe Features
The safety provided by the LM3641 goes beyond the normal
operation of the IC. The design of the IC includes many as-
pects that continue to assure protection of the cells even
when malfunctions occur.
•
A rugged internal sense resistor offers precise overcur-
rent response (magnitude and time) which allows smaller
volume power MOSFETs to be used. If the internal resis-
tor’s sense circuitry’s input open circuit (very unlikely),
the MOSFET pair will turn OFF. The IC will fail safe.
•
The external MOSFETs are specified to provide ad-
equate illegal charger withstand capability. Because of
M3, the IC is designed to never be exposed to more than
the actual cell voltage. Therefore the IC’s maximum rated
supply voltage does not limit the magnitude of illegal
charger voltages that can be protected by the IC. M3’s Vt
also guarantees that shorted cells can not be charged.
•
If any pin becomes detached from the PCB, either the
MOSFETs will turn OFF or the part will continue to protect
the Cell.
9
www.national.com
Disconnect
Charging
Battery pack mode of operation where
the MOSFET pair is OFF.
Fail Safe Features (Continued)
•
In the event of an extremely high charge current, the cell
voltage could exceed the maximum supply rating of the
IC. The IC is protected by internal voltage clamps and the
external 100Ω resistors R3 and R4.
State of current conduction into positive
terminal of battery pack from a current
limited voltage source that does not ex-
ceed the maximum voltage rating of the
MOSFET pair.
•
The external MOSFET pair turn-off resistor R2 aids in fail
safe operation in the rare event that the IC fails. Dual in-
dependently controlled series switches internal to the IC
must both turn on to allow the MOSFET pair to conduct.
If either control signal is in error, the external resistor R2
will ensure that the MOSFET pair turn OFF.
Discharging
IC Enabled
IC Disabled
State of current conduction out of the
positive terminal of battery pack into a
load.
The state when the Enable pin potential
is set to the V+ potential. The IC operates
with full functionality.
•
•
The LM3641 is 100
% tested for all aspects of operation.
The digital design-for-test methodology allows the cir-
cuitry to be tested at a greatly accelerated rate while
maintaining near perfect fault coverage.
The IC state when the Enable pin is float-
ing or pulled low, such as in a detached
pack. The Enable pin will be pulled to VSS
with an internal current source,
IENABLE PIN. The IC will go into power-
down and the MOSFET pair is turned
OFF to protect the pack from accidental
short circuits, invalid chargers or invalid
loads.
The cell bypass resistor prevents leakage current from
continuing to charge overcharged cells.
PCB Safety Considerations
•
The power MOSFET turn-OFF resistor R2 is critical for
proper turn-OFF of the MOSFETs during a fault condition.
Precaution is necessary so that this resistor or its con-
tacts to the FET terminals is not interrupted by defects
during and after the PCB assembly. The most robust de-
sign is to replicate this resistor and its connections (see
Figure 6).
Recovery
The ability to safely return to conduction
mode after a fault condition has caused
the MOSFET pair to turn OFF. Recovery
is accomplished with a low to high signal
on the Enable pin for overcharge, over-
discharge and overcurrent.
•
The IC bypass capacitor, C1, maintains stable operation
of the IC’s analog functions. This component’s presence
can be assured with a redundant capacitor (see Figure
6).
Recovery from overdischarge is auto-
matic with the application of a charger.
Recovery from overcharge is automatic
with the application of a load. Recovery
from overcurrent is automatic when the
impedance at the terminal pack exceeds
4–7 MΩ.
Pin Description
tFET-TURN-OFF
The turn-off time of the MOSFET pair.
This parameter is dependent on the ex-
ternal components used, however the
typical time is 1–4 ms.
Power-down
A reduced power state resulting from a
floating Enable. The MOSFET pair is al-
ways OFF.
DS012931-16
FIGURE 5. Connection Diagram
Cell-Bypass
resistor
A resistor that is connected across the
cell(s) whenever overcharge conditions
are detected. If the MOSFET pair is OFF
and a charger applied, then some of the
current in the V− pin would flow through
the cell. This resistor ensures that the cell
is discharged and not charged during
such an event. This resistor also com-
pensates for the possibility of leaking
OFF MOSFET pair overcharging the
cell(s).
Rsense Terminal of the internal current sensing resistor.
VSS
Negative IC supply and sense pin for the cell’s
negative terminal.
Enable Enable/Disable for MOSFET drive and power-
down mode. Also used to recover from fault condi-
tions.
V+
Sense pin for the cell’s positive terminal.
Positive IC supply.
VDD
Full
High impedance pull-up signal indicating that the
overcharge transition has occurred.
MOSFET Bypass A resistor that is connected across the
resistor
MOSFETs after overcurrent fault. When
the pack impedance 3–7 MΩ, the MOS-
FET bypass resistor reduces the MOS-
FET voltage to less than VRECOVERY and
the MOSFET turns ON. If the MOSFET
bypass resistor is active, and the Enable
goes low, the bypass resistor turns OFF.
V−
Pin used to monitor the negative terminal potential
of the battery pack.
GATE
Gate drive for the external MOSFET pair. This pin
is switched to VDD in the ON condition and is high
impedance for the OFF condition.
LCCE
Return to conduction mode for overdis-
charged packs does not require a low to
high edge on the Enable pin. The appli-
cation of a charger will turn on the FETs.
Glossary of Terms
Conduction
Battery pack mode of operation when the
MOSFET pair is ON.
www.national.com
10
charger is applied to the pack.
This current is limited by the V−
pin’s external resistor, R1.
Glossary of Terms (Continued)
This is also defined as the Low Cell
Charge Enable (LCCE). This way, deeply
discharged packs can be charged even if
the cell voltage is too low to enable the
logic to operate. See also, the M3 section
in the “Component Selection”.
IENABLE PIN
The internal pulldown current for
the Enable pin; terminated at
VSS
.
tSAMPLE
The time period between cell
voltage measurements.
tSAMPLE-4X
The time period between cell
Glossary of Specification
voltage measurements after
1
overcharge measurement and
before 4 normal cell voltage mea-
surements.
Parameters
VMAX
The maximum steady state cell
voltage for disconnect mode.
tOVERCURRENT
The time period for which the bat-
tery current must be greater than
the maximum current limit prior to
turning the MOSFET pair OFF.
VSAFE-OVER-CHARGE
The maximum cell voltage over-
shoot for conduction mode, re-
ferred to VMAX
.
VMIN
The minimum steady state cell
voltage for conduction mode.
tFET-TURN-ON
Turn-on time (MOSFET pair VGS
>
Vt) with 1 MΩ and 2 nF load at
VMIN-CELL-CHARGE
The minimum cell voltage for
which conduction mode for
charging is guaranteed. Cell volt-
ages below this value will not be
charged, that is the MOSFET pair
will remain OFF. This feature en-
sures that very deeply dis-
charged cells will be chargeable.
the GATE pin.
tENABLE-RECOVERY
The delay time after the Enable
pin is reconnected to V+ before
the MOSFET pair is allowed to
turn-on. This prevents switching
“chatter” of the MOSFET pair
during insertion to a charger or
load.
VGATE-FETS-ON
The maximum pull-up voltage of
the GATE pin in conduction
mode.
Component Selection
IGATE-FETS-ON
The pull-up current available
from the GATE pin in transition to
the conduction mode. This cur-
rent collapses to zero at GATE =
M1 & M2
The power N-MOSFETs must be able to isolate the cell from
invalid charge voltages, when the MOSFETs are OFF. The
breakdown voltage from drain to source determines the
maximum charger or reversed charger voltage tolerated. In-
valid chargers that exceed this breakdown voltage will allow
unlimited charge currents and therefore it is recommended
to provide secondary protection with passive thermal and/or
current fuses.
VDD
.
IGATE-FETS-OFF
VRECOVERY
The leakage current of the GATE
pin in disconnect mode.
The voltage across the MOSFET
pair that is used to detect if a
charger or a load is connected to
the battery pack. This voltage is
the difference between the V−
and VSS pins. The voltage be-
tween these pins is forced to
The maximum gate to source DC voltage is the cell voltage.
The VGS may peak momentarily during the MOSFETs turn
ON from an OFF condition with a charger applied. This
causes the charger voltage to appear across the gate to
source voltage. So, choose MOSFETs than can withstand
this voltage.
equal VRECOVERY after
a load
has been applied to an over-
charged pack in order to dis-
charge the pack without the
MOSFET cycling ON/OFF.
The LM3641 has limited gate pin drive current and therefore,
the maximum VGS rating of the MOSFETs must be higher
than the illegal charger voltage. The selection of the MOS-
FETs’ ON impedance is a pack power efficiency consider-
ation.
IMAX-CHG
IMAX-DIS
ISUPPLY
The maximum magnitude termi-
nal current allowed during charge
mode.
The MOSFETs maximum DC current operation should ex-
ceed the maximum rating of the LM3641’s overcurrent pro-
tection. Junction thermal conditions of the MOSFETs are of
prime importance in designing a reliable system. For ex-
ample, a dual MOSFET can have an IMAX rating of 5A. This
rating however is valid when either one of the MOSFETs is
ON. If both MOSFETs are ON, the rating for IMAX is less than
2.5A, because you have twice the RDSON, so twice the
power dissipation. Two single MOSFETs might give you a
better solution.
The maximum magnitude termi-
nal current allowed during dis-
charge mode.
The IC supply excluding the cur-
rent needed to supply the MOS-
FET turn-on current. The MOS-
FET turn-on current is calculated
by VCELL/R2 4 µA. The IC sup-
ply current flows between the
The peak currents encountered during short circuit are of
prime consideration in specifying the MOSFETs. The peak
current of parallel connected cells will be greater. Different
cell chemistries give different peak currents. The ON resis-
V
DD and VSS pins. Additional cur-
rent can flow from the VDD and
VSS pins to the V− pin when the
MOSFET pair is OFF and
a
11
www.national.com
The operating VGSmax ≤ VCELL. The Vt of M3 has signifi-
cance in that it determines what minimum value of cell volt-
age is allowed for charging. When the cell voltage is lower
than the VGSM3 required to conduct VCELL/R2, M1 and M2
can not be turned ON and the pack is unchargeable. This is
useful for preventing the charging of shorted cells, while re-
viving packs that have become deeply discharged during ex-
tended storage.
Component Selection (Continued)
tance of the MOSFETs ultimately determines the peak cur-
rent in short circuit and therefore is a useful parameter for
determining if the MOSFETs are compatible for the applica-
tion. The proper pack design dictates that the MOSFETs are
capable of withstanding repeated short circuit events over
the life of the pack without developing opens or shorts be-
tween the drain and source.
R’s and C’s
M3
For the resistors and capacitors used in the application cir-
This P-MOSFET is necessary for isolating the IC from invalid
chargers. Its drain to source voltage breakdown should ex-
ceed that of M1 and M2. The on conductance and gm can be
very poor and serve the purpose of driving the power MOS-
FETs M1 and M2 as the steady state drive is only VCELL/R2.
cuit, Table 1 will give the acceptable value range and the ef-
fected parameters. The function of each of these compo-
nents is described in the “Application Circuit” section.
TABLE 1. Component Acceptable Value Range and Effected Parameters
Component
Acceptable Value Range
100 kΩ–1 MΩ
1 MΩ
Parameters Effected
Tolerated magnitude of invalid charger
R1
R2
ISUPPLY vs. MOSFET turnoff delay
R3, R4
R5
50Ω–500Ω
Current limit in extreme over voltage condition vs. IR drop of ISUPPLY
Current limit in pack ESD event vs. IR drop of IENABLE
IOL vs. VOH of Full signal
100 kΩ–1 MΩ
100 kΩ–1 MΩ
0.01 µF–0.1 µF
0.01 µF–0.1 µF
0.01 µF–0.1 µF
220 pF–1 nF
R6
C1
Depends on frequency of noise loading the pack
Depends on impedance spectrum of Cells
C2
C3
Depends on MOSFET/Cell behavior during pack short circuit
Equally effective during pack short circuit
C4
www.national.com
12
Application Circuit
DS012931-17
FIGURE 6. Application Circuit
The pack current flows through the series path of the cell, the
sense resistor and the power MOSFETs, M1 and M2. M3
isolates the IC against high compliance voltage chargers
when the power MOSFETs are OFF. The V− pin detects the
polarity of voltage across the power MOSFETs. R1 limits the
current into the V− pin when a charger is applied and the
MOSFETs are OFF. R3 and R4 limit the current into the IC in
the event of extreme charge current. They also prevent the
cell to be shorted when the VDD or V+ pin becomes shorted,
either internally or externally. R5 provides ESD protection of
the IC from the pack terminal “E”. C1 bypasses transient Cell
currents so that the IC supply current is not interrupted. The
bypass of VDD is critical for stable operation, therefore it is
advised that 2 parallel bypass capacitors C1A and C1B be
used for redundancy. C2 is necessary to prevent the power
MOSFETs from oscillating when the pack is short circuited.
C3 suppresses possible oscillation of the MOSFETs during
pack short circuit. C3 can be duplicated for extra safety. The
same can be said for R2, which is used for proper turn OFF
of the MOSFETs during a fault condition. C4 isolates the En-
able pin from false reset signals during a pack short circuit
event. Series C2 and C3 also provide high frequency bypass
of the Cells which exhibit large impedance increase beyond
10–100 kHz. R6 has to be added to pull up the Full pin. The
Enable section is optional. R5 and C4 are only needed if the
3rd terminal of the pack is used for the Enable function (see
Product Description, “Enable Pin” section). If not used, short
the Enable pin to the VDD pin.
13
www.national.com
State Diagram
DS012931-19
FIGURE 7. State Diagram for LM3641 Operation
www.national.com
14
15
Physical Dimensions inches (millimeters) unless otherwise noted
8-Lead SOIC (M08A)
Order Number LM3641M
NS Package Number M08A
This device is factory programmable. Contact your local NSC sales office for ordering information.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE-
VICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI-
CONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or sys-
tems which, (a) are intended for surgical implant into
the body, or (b) support or sustain life, and whose fail-
ure to perform when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be rea-
sonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
Fax: +49 (0) 1 80-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
Email: sea.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
This datasheet has been download from:
www.datasheetcatalog.com
Datasheets for electronics components.
相关型号:
©2020 ICPDF网 联系我们和版权申明