LM4125AIM5X-2.0/NOPB [NSC]
IC,VOLT REFERENCE,FIXED,2V,BIPOLAR,TSOP,5PIN,PLASTIC;型号: | LM4125AIM5X-2.0/NOPB |
厂家: | National Semiconductor |
描述: | IC,VOLT REFERENCE,FIXED,2V,BIPOLAR,TSOP,5PIN,PLASTIC 光电二极管 |
文件: | 总13页 (文件大小:330K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
National Semiconductor is now part of
Texas Instruments.
Search http://www.ti.com/ for the latest technical
information and details on our current products and services.
November 2003
LM4125
Precision Micropower Low Dropout Voltage Reference
General Description
Features
n Small SOT23-5 package
n Low dropout voltage:
The LM4125 is a precision low power low dropout bandgap
voltage reference with up to 5 mA output current source and
sink capability.
@
120 mV Typ 1 mA
n High output voltage accuracy:
n Source and Sink current output:
n Supply current:
n Low Temperature Coefficient:
n Fixed output voltages:
n Industrial temperature Range:
0.2%
5 mA
This series reference operates with input voltages as low as
2V and up to 6V consuming 160 µA (Typ.) supply current. In
power down mode, device current drops to less than 2 µA.
160 µA Typ.
50 ppm/˚C
2.048, 2.5,and 4.096
−40˚C to +85˚C
The LM4125 comes in two grades (A and Standard) and
three voltage options for greater flexibility. The best grade
devices (A) have an initial accuracy of 0.2%, while the stan-
dard have an initial accuracy of 0.5%, both with a tempco of
50ppm/˚C guaranteed from −40˚C to +125˚C.
n (For extended temperature range, −40˚C to 125˚C,
contact National Semiconductor)
The very low dropout voltage, low supply current and power-
down capability of the LM4125 makes this product an ideal
choice for battery powered and portable applications.
Applications
n Portable, battery powered equipment
n Instrumentation and process control
n Automotive & Industrial
n Test equipment
The device performance is guaranteed over the industrial
temperature range (−40˚C to +85˚C), while certain specs are
guaranteed over the extended temperature range (−40˚C to
+125˚C). Please contact National for full specifications over
the extended temperature range. The LM4125 is available in
a standard 5-pin SOT-23 package.
n Data acquisition systems
n Precision regulators
n Battery chargers
n Base stations
n Communications
n Medical equipment
Connection Diagram
20069802
Refer to the Ordering Information Table in this Data Sheet for Specific Part Number
SOT23-5 Surface Mount Package
© 2003 National Semiconductor Corporation
DS200698
www.national.com
Ordering Information
Industrial Temperature Range (−40˚C to + 85˚C)
LM4125 Supplied as
1000 Units, Tape and
Reel
LM4125 Supplied as
3000 Units, Tape and
Reel
Initial Output Voltage Accuracy at 25˚C
And Temperature Coefficient
Top
Marking
LM4125AIM5-2.0
LM4125AIM5-2.5
LM4125AIM5-4.1
LM4125IM5-2.0
LM4125IM5-2.5
LM4125IM5-4.1
LM4125AIM5X-2.0
LM4125AIM5X-2.5
LM4125AIM5X-4.1
LM4125IM5X-2.0
LM4125IM5X-2.5
LM4125IM5X-4.1
R80A
R81A
R82A
R80B
R81B
R82B
0.2%, 50 ppm/˚C max (A grade)
0.5%, 50 ppm/˚C max
SOT-23 Package Marking Information
Only four fields of marking are possible on the SOT-23’s small surface. This
table gives the meaning of the four fields.
Field Information
First Field:
R = Reference
Second and third Field:
80 = 2.048V Voltage Option
81 = 2.500V Voltage Option
82 = 4.096V Voltage Option
Fourth Field:
A-B = Initial Reference Voltage Tolerance
A = 0.2%
B = 0.5%
www.national.com
2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Lead Temperature:
Soldering, (10 sec.)
Vapor Phase (60 sec.)
Infrared (15 sec.)
+260˚C
+215˚C
+220˚C
Maximum Voltage on input or
enable pins
−0.3V to 8V
Indefinite
Operating Range (Note 1)
Storage Temperature
Range
Output Short-Circuit Duration
Power Dissipation (TA = 25˚C) (Note 2):
MA05B package − θJA
Power Dissipation
−65˚C to +150˚C
−40˚C to +85˚C
−40˚C to +125˚C
280˚C/W
350 mW
Ambient Temperature
Range
ESD Susceptibility (Note 3)
Human Body Model
Junction Temperature
Range
2 kV
Machine Model
200V
Electrical Characteristics
LM4125-2.048V and 2.5V Unless otherwise specified VIN = 3.3V, ILOAD = 0, COUT = 0.01µF, TA = Tj = 25˚C.
Limits with standard typeface are for Tj = 25˚C, and limits in boldface type apply over the −40˚C ≤ TA ≤ +85˚C temperature
range.
Min
(Note 5)
Typ
(Note 4)
Max
(Note 5)
Symbol
Parameter
Conditions
Units
Output Voltage Initial
Accuracy
0.2
%
LM4125A-2.048
LM4125A-2.500
LM4125-2.048
LM4125-2.500
Temperature
VOUT
0.5
50
%
TCVOUT/˚C
−40˚C ≤ TA ≤ +125˚C
14
0.0007
0.03
ppm/˚c
Coefficient
∆VOUT/∆VIN
Line Regulation
3.3V ≤ VIN ≤ 6V
0.008
0.01
0.08
0.17
0.04
0.1
%/V
0 mA ≤ ILOAD ≤ 1 mA
1 mA ≤ ILOAD ≤ 5 mA
0.01
∆VOUT/∆ILOAD
Load Regulation
%/mA
−1 mA ≤ ILOAD ≤ 0 mA
−5 mA ≤ ILOAD ≤ −1 mA
ILOAD = 0 mA
0.04
0.01
45
0.12
65
100
150
200
210
300
Dropout Voltage
(Note 6)
ILOAD = +1 mA
ILOAD = +5 mA
120
180
VIN−VOUT
mV
VN
IS
Output Noise Voltage 0.1 Hz to 10 Hz
20
36
µVPP
µVPP
µA
(Note 8)
10 Hz to 10 kHz
Supply Current
160
257
290
VIN = 3.3V, VOUT = 0
VIN = 6V, VOUT = 0
−40˚C ≤ TA ≤ 125˚C
15
17
6
6
30
30
ISC
Short Circuit Current
mA
Hyst
Thermal Hysteresis
(Note 7)
0.5
mV/V
3
www.national.com
Electrical Characteristics
LM4125-2.048V and 2.5V Unless otherwise specified VIN = 3.3V, ILOAD = 0, COUT = 0.01µF, TA = Tj = 25˚C.
Limits with standard typeface are for Tj = 25˚C, and limits in boldface type apply over the −40˚C ≤ TA ≤ +85˚C temperature
range. (Continued)
Min
(Note 5)
Typ
(Note 4)
100
Max
(Note 5)
Symbol
∆VOUT
Parameter
Conditions
Units
@
Long Term Stability
(Note 9)
1000 hrs. 25˚C
ppm
Electrical Characteristics
LM4125-4.096V
Unless otherwise specified VIN = 5V, ILOAD = 0, COUT = 0.01µF, TA = Tj = 25˚C. Limits with standard typeface are for Tj =
25˚C, and limits in boldface type apply over the −40˚C ≤ TA ≤ +85˚C temperature range.
Typ (Note Max (Note
Symbol
Parameter
Conditions
Min (Note 5)
Units
4)
5)
Output Voltage Initial
Accuracy
0.2
%
VOUT
LM4125A-4.096
LM4125-4.096
Temperature
0.5
50
%
TCVOUT/˚C
−40˚C ≤ TA ≤ +125˚C
14
0.0007
0.03
ppm/˚c
Coefficient
∆VOUT/∆VIN
Line Regulation
5V ≤ VIN ≤ 6V
0.008
0.01
0.08
0.17
0.04
0.1
%/V
0 mA ≤ ILOAD ≤ 1 mA
1 mA ≤ ILOAD ≤ 5 mA
0.01
∆VOUT/∆ILOAD
Load Regulation
%/mA
−1 mA ≤ ILOAD ≤ 0 mA
−5 mA ≤ ILOAD ≤ −1 mA
ILOAD = 0 mA
0.04
0.01
45
0.12
65
100
150
200
210
300
Dropout Voltage
(Note 6)
ILOAD = +1 mA
ILOAD = +5 mA
120
180
VIN−VOUT
mV
VN
IS
Output Noise Voltage 0.1 Hz to 10 Hz
20
36
µVPP
µVPP
µA
(Note 8)
10 Hz to 10 kHz
Supply Current
160
257
290
VOUT = 0
15
17
6
6
30
30
ISC
Short Circuit Current
mA
VIN = 6V, VOUT = 0
−40˚C ≤ TA ≤ 125˚C
Hyst
Thermal Hysteresis
(Note 7)
0.5
100
mV/V
ppm
@
1000 hrs. 25˚C
∆VOUT
Long Term Stability
(Note 9)
www.national.com
4
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see Electrical Characteristics. The
guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed
test conditions.
Note 2: Without PCB copper enhancements. The maximum power dissipation must be de-rated at elevated temperatures and is limited by T
(maximum
JMAX
junction temperature), θ (junction to ambient thermal resistance) and T (ambient temperature). The maximum power dissipation at any temperature is: PDiss
J-A
A
MAX
= (T
− T )/θ
up to the value listed in the Absolute Maximum Ratings.
JMAX
A
J-A
Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200 pF capacitor discharged
directly into each pin.
Note 4: Typical numbers are at 25˚C and represent the most likely parametric norm.
Note 5: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate National’s Averaging Outgoing Quality Level (AOQL).
Note 6: Dropout voltage is the differential voltage between V
and V at which V
changes ≤ 1% from V
at V = 3.3V for 2.0V, 2.5V and 5V for 4.1V. A
OUT IN
OUT
IN
OUT
parasitic diode exists between input and output pins; it will conduct if V
is pulled to a higher voltage than V .
OUT
IN
Note 7: Thermal hysteresis is defined as the change in +25˚C output voltage before and after exposing the device to temperature extremes.
Note 8: Output noise voltage is proportional to V . V for other voltage option is calculated using (V /1.8) * V . V (2.5V) = (36µV /1.8) * 2.5 = 46µV .
PP
OUT
N
N(1.8V)
OUT
N
PP
Note 9: Long term stability is change in V
at 25˚C measured continuously during 1000 hrs.
REF
5
www.national.com
LM4125 Typical Operating Characteristics
Unless otherwise specified, VIN = 3.3V, VOUT = 2.5V,
ILOAD = 0, COUT = 0.022µF and TA = 25˚C.
Long Term Drift
Typical Temperature Drift
20069812
20069813
Short Circuit Current vs Temperature
Dropout Voltage vs Output Error
20069814
20069815
Dropout Voltage vs Load Current
Load Regulation
20069833
20069818
www.national.com
6
LM4125 Typical Operating Characteristics Unless otherwise specified, VIN = 3.3V, VOUT = 2.5V,
ILOAD = 0, COUT = 0.022µF and TA = 25˚C. (Continued)
GND Pin Current at No Load
GND Pin Current
vs Temperature
20069819
20069821
GND Pin Current vs Load
0.1Hz to 10Hz output Noise
20069823
20069822
Output Impedance vs Frequency
PSRR vs Frequency
20069824
20069825
7
www.national.com
LM4125 Typical Operating Characteristics Unless otherwise specified, VIN = 3.3V, VOUT = 2.5V,
ILOAD = 0, COUT = 0.022µF and TA = 25˚C. (Continued)
Start-Up Response
Load Step Response
Thermal Hysteresis
Load Step Response
20069826
20069828
Line Step Response
20069829
20069830
20069831
www.national.com
8
sion references and is induced by thermal-mechanical pack-
age stress. Changes in environmental storage temperature,
operating temperature and board mounting temperature are
all factors that can contribute to thermal hysteresis.
Pin Functions
Output (Pin 5): Reference Output.
Input (Pin 4):Positive Supply.
Ground (Pin 2):Negative Supply or Ground Connection.
Application Hints
The standard application circuit for the LM4125 is shown in
Figure 1. It is designed to be stable with ceramic output
capacitors in the range of 0.022µF to 0.1µF. Note that
0.022µF is the minimum required output capacitor. These
capacitors typically have an ESR of about 0.1 to 0.5Ω.
Smaller ESR can be tolerated, however larger ESR can not.
The output capacitor can be increased to improve load tran-
sient response, up to about 1µF. However, values above
0.047µF must be tantalum. With tantalum capacitors, in the
1µF range, a small capacitor between the output and the
reference pin is required. This capacitor will typically be in
the 50pF range. Care must be taken when using output
capacitors of 1µF or larger. These application must be thor-
oughly tested over temperature, line and load.
20069832
FIGURE 1.
INPUT CAPACITOR
Noise on the power-supply input can effect the output noise,
but can be reduced by using an optional bypass capacitor
between the input pin and the ground.
An input capacitor is typically not required. However, a 0.1µF
ceramic can be used to help prevent line transients from
entering the LM4125. Larger input capacitors should be
tantalum or aluminium.
PRINTED CIRCUIT BOARD LAYOUT CONSIDERATION
The mechanical stress due to PC board mounting can cause
the output voltage to shift from its initial value. References in
SOT packages are generally less prone to assembly stress
than devices in Small Outline (SOIC) package.
The typical thermal hysteresis specification is defined as the
change in +25˚C voltage measured after thermal cycling.
The device is thermal cycled to temperature -40˚C and then
measured at 25˚C. Next the device is thermal cycled to
temperature +125˚C and again measured at 25˚C. The re-
sulting VOUT delta shift between the 25˚C measurements is
thermal hysteresis. Thermal hysteresis is common in preci-
To reduce the stress-related output voltage shifts, mount the
reference on the low flex areas of the PC board such as near
to the edge or the corner of the PC board.
9
www.national.com
Typical Application Circuits
Voltage Reference with Complimentary Output
Voltage Reference with Negative Output
20069806
Precision High Current Low Droput Regulator
20069803
Precision High Current Low Dropout Regulator
20069807
Precision Voltage Reference
with Force and Sense Output
20069804
Precision High Current
Negative Voltage Regulator
20069809
Programmable Current Source
20069805
20069810
www.national.com
10
Typical Application Circuits
Power Supply Splitter
(Continued)
Precision Regulator with Current Limiting Circuit
20069820
20069811
11
www.national.com
Physical Dimensions inches (millimeters)
unless otherwise noted
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification
(CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明