LM4877 [NSC]
1 Watt Audio Power Amplifier in micro SMD package with Shutdown Logic Low; 1瓦音频功率放大器的micro SMD封装,具有关断逻辑低型号: | LM4877 |
厂家: | National Semiconductor |
描述: | 1 Watt Audio Power Amplifier in micro SMD package with Shutdown Logic Low |
文件: | 总14页 (文件大小:431K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
February 2000
LM4877
1 Watt Audio Power Amplifier in micro SMD package
with Shutdown Logic Low
General Description
Key Specifications
The LM4877 is a bridge-connected audio power amplifier ca-
pable of delivering 1 W of continuous average power to an
8Ω load with less than .2% (THD) from a 5V power supply.
n Power Output at 0.2% THD
n Shutdown Current
1 W (typ)
0.01 µA (typ)
Boomer audio power amplifiers were designed specifically to
provide high quality output power with a minimal amount of
external components. Since the LM4877 does not require
output coupling capacitors or bootstrap capacitors. It is opti-
mally suited for low-power portable applications.
Features
n micro SMD package (see App. note AN-1112)
n 5V - 2V operation
n No output coupling capacitors or bootstrap capacitors.
n Unity-gain stable
n External gain configuration capability
The LM4877 features an externally controlled, low-power
consumption shutdown mode, as well as an internal thermal
shutdown protection mechanism.
The unity-gain stable LM4877 can be configured by external
gain-setting resistors.
Applications
n Cellular Phones
n Portable Computers
n Low Voltage Audio Systems
Typical Application
Connection Diagram
8 Bump micro SMD
DS101290-23
Top View
Order Number LM4877IBP, LM4877IBPX
See NS Package Number BPA08B6B
DS101290-1
FIGURE 1. Typical Audio Amplifier Application Circuit
Boomer® is a registered trademark of National Semiconductor Corporation.
© 2000 National Semiconductor Corporation
DS101290
www.national.com
Absolute Maximum Ratings (Note 2)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Soldering Information
See AN-1112 ″Micro-SMD Wafers Level Chip Scale
Package″.
Supply Voltage
6.0V
−65˚C to +150˚C
−0.3V to VDD +0.3V
Internally Limited
2500V
Operating Ratings
Storage Temperature
Input Voltage
Temperature Range
Power Dissipation (Note 3)
ESD Susceptibility (Note 4)
ESD Susceptibility (Note 5)
Junction Temperature
TMIN ≤ TA ≤ TMAX
−40˚C ≤ TA ≤ 85˚C
2.0V ≤ VDD ≤ 5.5V
Supply Voltage
250V
150˚C
Electrical Characteristics VDD = 5V (Notes 1, 2, 9)
The following specifications apply for VDD = 5V and 8Ω Load unless otherwise specified. Limits apply for TA = 25˚C.
LM4877
Units
Symbol
Parameter
Conditions
Typical
Limit
(Limits)
(Note 6)
(Note 7)
VDD
Supply Voltage
2.0
5.5
7
V (min)
V (max)
mA (max)
µA (max)
mV (max)
W
IDD
Quiescent Power Supply Current
Shutdown Current
VIN = 0V, Io = 0A
5.3
0.01
5
ISD
VPIN5 = 0V
2
VOS
Po
Output Offset Voltage
Output Power
VIN = 0V
50
THD = 0.2% (max); f = 1 kHz
1
THD+N
Total Harmonic Distortion+Noise
Po = 0.25 Wrms; AVD = 2; 20 Hz ≤
f ≤ 20 kHz
0.1
%
PSRR
Power Supply Rejection Ratio
VDD = 4.9V to 5.1V
65
dB
Electrical Characteristics VDD = 3.3V (Notes 1, 2, 9)
The following specifications apply for VDD = 3.3V and 8Ω Load unless otherwise specified. Limits apply for TA = 25˚C.
LM4877
Units
Symbol
Parameter
Conditions
Typical
Limit
(Note 7)
2.0
(Limits)
(Note 6)
VDD
Supply Voltage
V (min)
V (max)
mA (max)
µA (max)
mV (max)
W
5.5
IDD
Quiescent Power Supply Current
Shutdown Current
VIN = 0V, Io = 0A
4
0.01
5
ISD
VPIN5 = 0V
VOS
Po
Output Offset Voltage
Output Power
VIN = 0V
THD = 1% (max); f = 1 kHz
.5
.45
THD+N
Total Harmonic Distortion+Noise
Po = 0.25 Wrms; AVD = 2; 20 Hz ≤
f ≤ 20 kHz
0.15
%
PSRR
Power Supply Rejection Ratio
VDD = 3.2V to 3.4V
65
dB
Electrical Characteristics VDD = 2.6V (Notes 1, 2, 8, 9)
The following specifications apply for VDD = 2.6V and 8Ω Load unless otherwise specified. Limits apply for TA = 25˚C.
LM4877
Units
Symbol
VDD
Parameter
Conditions
Typical
Limit
(Note 7)
2.0
(Limits)
(Note 6)
Supply Voltage
V (min)
V (max)
5.5
IDD
Quiescent Power Supply Current
VIN = 0V, Io = 0A
3.4
mA (max)
www.national.com
2
Electrical Characteristics VDD = 2.6V (Notes 1, 2, 8, 9)
The following specifications apply for VDD = 2.6V and 8Ω Load unless otherwise specified. Limits apply for TA
=
25˚C. (Continued)
LM4877
Units
Symbol
Parameter
Conditions
Typical
(Note 6)
0.01
Limit
(Note 7)
(Limits)
ISD
VOS
P0
Shutdown Current
VPIN5 = 0V
VIN = 0V
µA (max)
mV (max)
Output Offset Voltage
5
Output Power ( 8Ω )
Output Power ( 4Ω )
THD = 0.3% (max); f = 1 kHz
THD = 0.5% (max); f = 1 kHz
0.25
0.5
W
W
THD+N
PSRR
Total Harmonic Distortion+Noise
Po = 0.25 Wrms; AVD = 2; 20 Hz ≤
f ≤ 20 kHz
0.25
%
Power Supply Rejection Ratio
VDD = 2.5V to 2.7V
65
dB
Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified.
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is func-
tional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guar-
antee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is
given, however, the typical value is a good indication of device performance.
Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
, θ , and the ambient temperature T . The maximum
JMAX JA
A
allowable power dissipation is P
= (T
–T )/θ or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4877, T
= 150˚C. The
DMAX
JMAX
A
JA
JMAX
typical junction-to-ambient thermal resistance is 150˚C/W.
Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 5: Machine Model, 220 pF–240 pF discharged through all pins.
Note 6: Typicals are measured at 25˚C and represent the parametric norm.
Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 8: Low Voltage Circuit - See Fig. 4
Note 9: Shutdown current is measured in a Normal Room Environment. Exposure to direct sunlight will increase I by a maximum of 2µA.
SD
Electrical Characteristics VDD = 5/3.3/2.6V Shutdown Input
LM4877
Units
Symbol
Parameter
Conditions
(Limits)
Typical
Limit
1.2
VIH
VIL
Shutdown Input Voltage High
Shutdown Input Voltage Low
V(min)
V(max)
0.4
External Components Description (Figure 1)
Components
Functional Description
1.
Ri
Inverting input resistance which sets the closed-loop gain in conjunction with Rf. This resistor also forms a
high pass filter with Ci at fC= 1/(2π RiCi).
2.
Ci
Input coupling capacitor which blocks the DC voltage at the amplifiers input terminals. Also creates a
highpass filter with Ri at fc = 1/(2π RiCi). Refer to the section, Proper Selection of External Components,
for an explanation of how to determine the value of Ci.
3.
4.
Rf
Feedback resistance which sets the closed-loop gain in conjunction with Ri.
CS
Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing
section for information concerning proper placement and selection of the supply bypass capacitor.
5.
CB
Bypass pin capacitor which provides half-supply filtering. Refer to the section, Proper Selection of External
Components, for information concerning proper placement and selection of CB.
3
www.national.com
Typical Performance Characteristics
THD+N vs Frequency
THD+N vs Frequency
at 5V and 8Ω
at 3.3V and 8Ω
DS101290-3
DS101290-6
DS101290-4
DS101290-8
THD+N vs Frequency
at 2.6V and 8Ω
THD+N vs Frequency
at 2.6V and 4Ω
DS101290-5
THD+N vs Output Power
VDD = 5V
THD+N vs Output Power
VDD = 3.3V
DS101290-7
www.national.com
4
Typical Performance Characteristics (Continued)
THD+N vs
THD+N vs
Output Power
Output Power
2.6V at 8Ω
2.6V at 4Ω
DS101290-9
DS101290-10
Output Power vs
Supply Voltage
Output Power vs
Load Resistance
DS101290-11
DS101290-12
Power Dissipation vs
Output Power
VDD = 5V
Power Derating Curve
DS101290-14
DS101290-26
5
www.national.com
Typical Performance Characteristics (Continued)
Power Dissipation vs
Output Power
VDD = 3.3V
Power Dissipation vs
Output Power
VDD = 2.6V
DS101290-27
DS101290-28
Clipping Voltage vs
Supply Voltage
Supply Current vs
Shutdown Voltage
@
LM4877 VDD = 5/3.3/2.6Vdc
DS101290-15
DS101290-35
Frequency Response vs
Input Capacitor Size
Power Supply
Rejection Ratio
DS101290-17
DS101290-18
www.national.com
6
Typical Performance Characteristics (Continued)
Open Loop
Frequency Response
Noise Floor
DS101290-19
DS101290-16
7
www.national.com
duced supply voltage, higher load impedance, or reduced
ambient temperature. The National Reference Design board
using a 5V supply and an 8 ohm load will run in a 110˚C am-
bient environement without exceeding TJMAX. Internal power
dissipation is a function of output power. Refer to the Typical
Performance Characteristics curves for power dissipation
information for different output powers and output loading.
Application Information
BRIDGE CONFIGURATION EXPLANATION
As shown in Figure 1, the LM4877 has two operational am-
plifiers internally, allowing for a few different amplifier con-
figurations. The first amplifier’s gain is externally config-
urable, while the second amplifier is internally fixed in a
unity-gain, inverting configuration. The closed-loop gain of
the first amplifier is set by selecting the ratio of Rf to Ri while
the second amplifier’s gain is fixed by the two internal 10 kΩ
resistors. Figure 1 shows that the output of amplifier one
serves as the input to amplifier two which results in both am-
plifiers producing signals identical in magnitude, but out of
phase by 180˚. Consequently, the differential gain for the IC
is
POWER SUPPLY BYPASSING
As with any amplifier, proper supply bypassing is critical for
low noise performance and high power supply rejection. The
capacitor location on both the bypass and power supply pins
should be as close to the device as possible. Typical applica-
tions employ a 5V regulator with 10 µF Tantalum or electro-
lytic capacitor and a 0.1 µF bypass capacitor which aid in
supply stability. This does not eliminate the need for bypass-
ing the supply nodes of the LM4877. The selection of a by-
pass capacitor, especially CB, is dependent upon PSRR re-
quirements, click and pop performance as explained in the
section Proper Selection of External Components, sys-
tem cost, and size constraints.
A
VD= 2 *(Rf/Ri)
By driving the load differentially through outputs Vo1 and
Vo2, an amplifier configuration commonly referred to as
“bridged mode” is established. Bridged mode operation is
different from the classical single-ended amplifier configura-
tion where one side of its load is connected to ground.
SHUTDOWN FUNCTION
A bridge amplifier design has a few distinct advantages over
the single-ended configuration, as it provides differential
drive to the load, thus doubling output swing for a specified
supply voltage. Four times the output power is possible as
compared to a single-ended amplifier under the same condi-
tions. This increase in attainable output power assumes that
the amplifier is not current limited or clipped. In order to
choose an amplifier’s closed-loop gain without causing ex-
cessive clipping, please refer to the Audio Power Amplifier
Design section.
In order to reduce power consumption while not in use, the
LM4877 contains a shutdown pin to externally turn off the
amplifier’s bias circuitry. This shutdown feature turns the am-
plifier off when a logic low is placed on the shutdown pin. By
switching the shutdown pin to ground, the LM4877 supply
current draw will be minimized in idle mode. While the device
will be disabled with shutdown pin voltages less than
0.4VDC, the idle current may be greater than the typical
value of 0.01 µA.
A bridge configuration, such as the one used in LM4877,
also creates a second advantage over single-ended amplifi-
ers. Since the differential outputs, Vo1 and Vo2, are biased
at half-supply, no net DC voltage exists across the load. This
eliminates the need for an output coupling capacitor which is
required in a single supply, single-ended amplifier configura-
tion. Without an output coupling capacitor, the half-supply
bias across the load would result in both increased internal
IC power dissipation and also possible loudspeaker damage.
In many applications, a microcontroller or microprocessor
output is used to control the shutdown circuitry which pro-
vides a quick, smooth transition into shutdown. Another solu-
tion is to use a single-pole, single-throw switch in conjunction
with an external pull-up resistor. When the switch is closed,
the shutdown pin is connected to ground and disables the
amplifier. If the switch is open, then the external pull-up re-
sistor will enable the LM4877. This scheme guarantees that
the shutdown pin will not float thus preventing unwanted
state changes. Another way to operate the shutdown circuit
is with a pulldown resistor (R1), as shown in the applications
circuit on Figure 3. J1 operates the shutdown function. J1
must be installed to operate the part. A switch may be in-
stalled in place of J1 for easier evaluation of the shutdown
function.
POWER DISSIPATION
Power dissipation is a major concern when designing a suc-
cessful amplifier, whether the amplifier is bridged or single-
ended. A direct consequence of the increased power deliv-
ered to the load by a bridge amplifier is an increase in
internal power dissipation. Since the LM4877 has two opera-
tional amplifiers in one package, the maximum internal
power dissipation is 4 times that of a single-ended amplifier.
The maximum power dissipation for a given application can
be derived from the power dissipation graphs or from Equa-
tion 1.
PROPER SELECTION OF EXTERNAL COMPONENTS
Proper selection of external components in applications us-
ing integrated power amplifiers is critical to optimize device
and system performance. While the LM4877 is tolerant of
external component combinations, consideration to compo-
nent values must be used to maximize overall system qual-
ity.
PDMAX = 4*(VDD)2/(2π2RL)
(1)
It is critical that the maximum junction temperature TJMAX of
150˚C is not exceeded. TJMAX can be determined from the
power derating curves by using PDMAX and the PC board foil
area. By adding additional copper foil, the thermal resistance
of the application can be reduced from a free air value of
150˚C/W, resulting in higher PDMAX. Additional copper foil
can be added to any of the leads connected to the LM4877.
It is especially effective when connected to VDD, GND, and
the output pins. Refer to the application information on the
LM4877 reference design board for an example of good heat
sinking. If TJMAX still exceeds 150˚C, then additional
changes must be made. These changes can include re-
The LM4877 is unity-gain stable which gives a designer
maximum system flexibility. The LM4877 should be used in
low gain configurations to minimize THD+N values, and
maximize the signal to noise ratio. Low gain configurations
require large input signals to obtain a given output power. In-
put signals equal to or greater than 1 Vrms are available
from sources such as audio codecs. Please refer to the sec-
tion, Audio Power Amplifier Design, for a more complete
explanation of proper gain selection.
Besides gain, one of the major considerations is the closed-
loop bandwidth of the amplifier. To a large extent, the band-
www.national.com
8
AUDIO POWER AMPLIFIER DESIGN
Application Information (Continued)
A 1W/8Ω AUDIO AMPLIFIER
width is dictated by the choice of external components
shown in Figure 1. The input coupling capacitor, Ci, forms a
first order high pass filter which limits low frequency re-
sponse. This value should be chosen based on needed fre-
quency response for a few distinct reasons.
Given:
Power Output
Load Impedance
Input Level
1 Wrms
8Ω
1 Vrms
20 kΩ
Selection Of Input Capacitor Size
Input Impedance
Large input capacitors are both expensive and space hungry
for portable designs. Clearly, a certain sized capacitor is
needed to couple in low frequencies without severe attenua-
tion. But in many cases the speakers used in portable sys-
tems, whether internal or external, have little ability to repro-
duce signals below 100 Hz to 150 Hz. Thus, using a large
input capacitor may not increase actual system perfor-
mance.
±
100 Hz–20 kHz 0.25 dB
Bandwidth
A designer must first determine the minimum supply rail to
obtain the specified output power. By extrapolating from the
Output Power vs Supply Voltage graphs in the Typical Per-
formance Characteristics section, the supply rail can be
easily found. A second way to determine the minimum sup-
ply rail is to calculate the required Vopeak using Equation 2
and add the output voltage. Using this method, the minimum
In addition to system cost and size, click and pop perfor-
mance is effected by the size of the input coupling capacitor,
Ci. A larger input coupling capacitor requires more charge to
reach its quiescent DC voltage (nominally 1/2 VDD). This
charge comes from the output via the feedback and is apt to
create pops upon device enable. Thus, by minimizing the ca-
pacitor size based on necessary low frequency response,
turn-on pops can be minimized.
supply voltage would be (Vopeak + (VOD
+ VODBOT)), where
VOD
and VOD
are extrapolated frToOmP the Dropout Volt-
TOP
age BvOsT Supply Voltage curve in the Typical Performance
Characteristics section.
(2)
Using the Output Power vs Supply Voltage graph for an 8Ω
load, the minimum supply rail is 4.6V. But since 5V is a stan-
dard voltage in most applications, it is chosen for the supply
rail. Extra supply voltage creates headroom that allows the
LM4877 to reproduce peaks in excess of 1W without produc-
ing audible distortion. At this time, the designer must make
sure that the power supply choice along with the output im-
pedance does not violate the conditions explained in the
Power Dissipation section.
Besides minimizing the input capacitor size, careful consid-
eration should be paid to the bypass capacitor value. Bypass
capacitor, CB, is the most critical component to minimize
turn-on pops since it determines how fast the LM4877 turns
on. The slower the LM4877’s outputs ramp to their quiescent
DC voltage (nominally 1/2 VDD), the smaller the turn-on pop.
Choosing CB equal to 1.0 µF along with a small value of Ci
(in the range of 0.1 µF to 0.39 µF), should produce a virtually
clickless and popless shutdown function. While the device
will function properly, (no oscillations or motorboating), with
Once the power dissipation equations have been addressed,
the required differential gain can be determined from Equa-
tion 3.
CB equal to 0.1 µF, the device will be much more susceptible
to turn-on clicks and pops. Thus, a value of CB equal to
1.0 µF is recommended in all but the most cost sensitive de-
signs.
(3)
Rf/Ri = AVD/2
LOW VOLTAGE APPLICATIONS ( BELOW 3.0 VDD
)
From Equation 3, the minimum AVD is 2.83; use AVD = 3.
The LM4877 will function at voltages below 3 volts but this
mode of operation requires the addition of a 1kΩ resistor
from each of the differential output pins ( pins 8 and 4 ) di-
rectly to ground. The addition of the pair of 1kΩ resistors ( R4
& R5 ) assures stable operation below 3 Volt Vdd operation.
The addition of the two resistors will however increase the
idle current by as much as 5mA. This is because at 0v input
both of the outputs of the LM4877’s 2 internal opamps go to
1/2 VDD ( 2.5 volts for a 5v power supply ), causing current to
flow through the 1K resistors from output to ground. See fig
4.
Since the desired input impedance was 20 kΩ, and with a
AVD impedance of 2, a ratio of 1.5:1 of Rf to Ri results in an
allocation of Ri = 20 kΩ and Rf = 30 kΩ. The final design step
is to address the bandwidth requirements which must be
stated as a pair of −3 dB frequency points. Five times away
from a −3 dB point is 0.17 dB down from passband response
±
which is better than the required 0.25 dB specified.
fL = 100 Hz/5 = 20 Hz
fH = 20 kHz * 5 = 100 kHz
As stated in the External Components section, Ri in con-
junction with Ci create a highpass filter.
Jumper options have been included on the reference design,
Fig. 4, to accommodate the low voltage application. J2 & J3
connect R4 and R5 to the outputs.
Ci ≥ 1/(2π*20 kΩ*20 Hz) = 0.397 µF; use 0.39 µF
The high frequency pole is determined by the product of the
desired frequency pole, fH, and the differential gain, AVD
.
With a AVD = 3 and fH = 100 kHz, the resulting GBWP =
150 kHz which is much smaller than the LM4877 GBWP of
4 MHz. This figure displays that if a designer has a need to
design an amplifier with a higher differential gain, the
LM4877 can still be used without running into bandwidth limi-
tations.
9
www.national.com
Application Information (Continued)
HIGHER GAIN AUDIO AMPLIFIER
DS101290-24
Figure 2
The LM4877 is unity-gain stable and requires no external
components besides gain-setting resistors, an input coupling
capacitor, and proper supply bypassing in the typical appli-
cation. However, if a closed-loop differential gain of greater
than 10 is required, a feedback capacitor may be needed as
shown in Figure 2 to bandwidth limit the amplifier. This feed-
back capacitor creates a low pass filter that eliminates
possible high frequency oscillations. Care should be taken
when calculating the -3dB frequency in that an incorrect
combination of R3 and C4 will cause rolloff before 20kHz. A
typical combination of feedback resistor and capacitor that
will not produce audio band high frequency rolloff is R3
=
20kΩ and C4 = 25pf. These components result in a -3dB
point of approximately 320 kHz. It is not recommended that
the feedback resistor and capacitor be used to implement a
band limiting filter below 100kHZ.
www.national.com
10
Application Information (Continued)
DIFFERENTIAL AMPLIFIER CONFIGURATION FOR
LM4877
DS101290-29
Figure 3
Mono LM4877 Reference Design Board - Assembly Part Number:
980011207-100 Revision: A Bill of Material
Item
Part Number
Part Description
Qty
Ref Designator
1
551011208-001
LM4877 Mono Reference
1
Design Board PCB etch 001
10
482911183-001
LM4877 Audio AMP micro
SMD 8 Bumps
1
U1
20
21
25
30
31
35
151911207-001
151911207-002
152911207-001
472911207-001
472911207-002
210007039-002
Cer Cap 0.1uF 50V +80/-20
1
1
1
3
2
3
C1
C2
1206
Cer Cap 0.39uF 50V Z5U 20
1210
Tant Cap 1uF 16V 10
C3
Size=A 3216
Res 20K Ohm 1/10W 5
R1, R2, R3
R4, R5,
J1, J2, J3
0805
Res 1K Ohm 1/10W 5
0805
Jumper Header Vertical
Mount 2X1 0.100
36
210007582-001
Jumper Shunt 2 position
0.100
3
11
www.national.com
Application Information (Continued)
Silk Screen
Top Layer
DS101290-30
DS101290-31
Bottom Layer
Inner Layer VDD
DS101290-32
DS101290-33
Inner Layer Ground
DS101290-34
www.national.com
12
Application Information (Continued)
REFERENCE DESIGN BOARD and PCB LAYOUT
GUIDELINES
DS101290-25
Figure 4
PCB Layout Guidelines
Single-Point Power / Ground Connections
This section provides practical guidelines for mixed signal
PCB layout that involves various digital/analog power and
ground traces. Designers should note that these are only
″rule-of-thumb″ recommendations and the actual results will
depend heavily on the final layout.
The analog power traces should be connected to the digital
traces through a single point (link). A ″Pi-filter″ can be helpful
in minimizing High Frequency noise coupling between the
analog and digital sections. It is further recommended to put
digital and analog power traces over the corresponding digi-
tal and analog ground traces to minimize noise coupling.
General Mixed Signal Layout Recommendation
Placement of Digital and Analog Components
Power and Ground Circuits
All digital components and high-speed digital signals traces
should be located as far away as possible from the analog
components and the analog circuit traces.
For 2 layer mixed signal design, it is important to isolate the
digital power and ground trace paths from the analog power
and ground trace paths. Star trace routing techniques (bring-
ing individual traces back to a central point rather than daisy
chaining traces together in a serial manner) can have a ma-
jor impact on low level signal performance. Star trace routing
refers to using individual traces to feed power and ground to
each circuit or even device. This technique will take require
a greater amount of design time but will not increase the final
price of the board. The only extra parts required will be some
jumpers.
Avoiding Typical Design / Layout Problems
Avoid ground loops or running digital and analog traces par-
allel to each other (side-by-side) on the same PCB layer.
When traces must cross over each other do it at 90 degrees.
Running digital and analog traces at 90 degrees to each
other from the top to the bottom side as much as possible will
minimize capacitive noise coupling and cross talk.
13
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
Note: Unless otherwise specified.
1. Epoxy coating.
2. 63Sn/37Pb eutectic bump.
3. Recommend non-solder mask defined landing pad.
4. Pin 1 is established by lower left corner with respect to text orientation pins are numbered counterclockwise.
5. Reference JEDEC registration MO-211, variation BC.
8-Bump micro SMD
Order Number LM4877IBP, LM4877IBPX
NS Package Number BPA08B6B
X1 = 1.31 X2 = 1.97 X3 = 0.850
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号:
©2020 ICPDF网 联系我们和版权申明